SEARCH · Search NASA

Results for “software defined radio (SDR)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Tactically Extensible and Modular Communications - X-Band TEMCOM-X

This paper will discuss a proposed CubeSat size (3U) telemetry system concept being developed at Marshall Space Flight Center (MSFC) in cooperation with the U.S. Department of the Army and Dynetics Corporation. This telemetry system incorporates efficient, high-bandwidth communications by developing flight-ready, low-cost, Protoflight software defined radio (SDR) and Electronically Steerable Patch Array (ESPA) antenna subsystems for use on platforms as small as CubeSats and unmanned aircraft systems (UASs). The current telemetry system is slightly larger in dimension of footprint than required to fit within a 0.5U CubeSat volume. Extensible and modular communications for CubeSat technologies will partially mitigate current capability gaps between traditional strategic space platforms and lower-cost small satellite solutions. Higher bandwidth capacity will enable high-volume, low error-rate data transfer to and from tactical forces or sensors operating in austere locations (e.g., direct imagery download, unattended ground sensor data exfiltration, interlink communications), while also providing additional bandwidth and error correction margin to accommodate more complex encryption algorithms and higher user volume.

Sims, William Herbert↗

NASA NTRS2015

High Data Rates for AubieSat-2 A & B, Two CubeSats Performing High Energy Science in the Upper Atmosphere

This paper will discuss a proposed CubeSat size (3 Units / 6 Units) telemetry system concept being developed at Marshall Space Flight Center (MSFC) in cooperation with Auburn University. The telemetry system incorporates efficient, high-bandwidth communications by developing flight-ready, low-cost, PROTOFLIGHT software defined radio (SDR) payload for use on CubeSats. The current telemetry system is slightly larger in dimension of footprint than required to fit within a 0.75 Unit CubeSat volume. Extensible and modular communications for CubeSat technologies will provide high data rates for science experiments performed by two CubeSats flying in formation in Low Earth Orbit. The project is a collaboration between the University of Alabama in Huntsville and Auburn University to study high energy phenomena in the upper atmosphere. Higher bandwidth capacity will enable high-volume, low error-rate data transfer to and from the CubeSats, while also providing additional bandwidth and error correction margin to accommodate more complex encryption algorithms and higher user volume.

Sims, William H.↗

NASA NTRS2015

Reconfigurable, Cognitive Software-Defined Radio

Software-defined radio (SDR) technology allows radios to be reconfigured to perform different communication functions without using multiple radios to accomplish each task. Intelligent Automation, Inc., has developed SDR platforms that switch adaptively between different operation modes. The innovation works by modifying both transmit waveforms and receiver signal processing tasks. In Phase I of the project, the company developed SDR cognitive capabilities, including adaptive modulation and coding (AMC), automatic modulation recognition (AMR), and spectrum sensing. In Phase II, these capabilities were integrated into SDR platforms. The reconfigurable transceiver design employs high-speed field-programmable gate arrays, enabling multimode operation and scalable architecture. Designs are based on commercial off-the-shelf (COTS) components and are modular in nature, making it easier to upgrade individual components rather than redesigning the entire SDR platform as technology advances.

Bhat, Arvind↗

NASA NTRS2015

Reconfigurable Very Long Instruction Word (VLIW) Processor

Future NASA missions will depend on radiation-hardened, power-efficient processing systems-on-a-chip (SOCs) that consist of a range of processor cores custom tailored for space applications. Aries Design Automation, LLC, has developed a processing SOC that is optimized for software-defined radio (SDR) uses. The innovation implements the Institute of Electrical and Electronics Engineers (IEEE) RazorII voltage management technique, a microarchitectural mechanism that allows processor cores to self-monitor, self-analyze, and selfheal after timing errors, regardless of their cause (e.g., radiation; chip aging; variations in the voltage, frequency, temperature, or manufacturing process). This highly automated SOC can also execute legacy PowerPC 750 binary code instruction set architecture (ISA), which is used in the flight-control computers of many previous NASA space missions. In developing this innovation, Aries Design Automation has made significant contributions to the fields of formal verification of complex pipelined microprocessors and Boolean satisfiability (SAT) and has developed highly efficient electronic design automation tools that hold promise for future developments.

Velev, Miroslav N.↗

NASA NTRS2016

An Optical Receiver Post-Processing System for the Integrated Radio and Optical Communications Software Defined Radio Test Bed

The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center is investigating the feasibility of a hybrid radio frequency (RF) and optical communication system for future deep space missions. As a part of this investigation, a test bed for a radio frequency (RF) and optical software defined radio (SDR) has been built. Receivers and modems for the NASA deep space optical waveform are not commercially available so a custom ground optical receiver system has been built. This paper documents the ground optical receiver, which is used in order to test the RF and optical SDR in a free space optical communications link.

optical communication↗

NASA NTRS2016

An Optical Receiver Post Processing System for the Integrated Radio and Optical Communications Software Defined Radio Test Bed

The Integrated Radio and Optical Communications (iROC) project at the National Aeronautics and Space Administrations (NASA) Glenn Research Center is investigating the feasibility of a hybrid radio frequency (RF) and optical communication system for future deep space missions. As a part of this investigation, a test bed for a radio frequency (RF) and optical software defined radio (SDR) has been built. Receivers and modems for the NASA deep space optical waveform are not commercially available so a custom ground optical receiver system has been built. This paper documents the ground optical receiver, which is used in order to test the RF and optical SDR in a free space optical communications link.

waveforms↗

NASA NTRS2017

PNT Activities at NASA Glenn Research Center

This presentation provides a review of Position Navigation and Timing activities at the Glenn Research Center. Topics include 1) contributions to simulation studies for the Space Service Volume of the Global Navigation Satellite System, 2) development and integration efforts for a Software Defined Radio (SDR) waveform for the Space Communications and Navigation (SCaN) testbed, currently onboard the International Space Station and 3) a GPS L5 testbed intended to explore terrain mapping capabilities with communications signals. Future directions are included and a brief discussion of NASA, GRC and the SCAN office.

Time↗

NASA NTRS2017

Software Defined Radios - Architectures, Systems and Functions

Software Defined Radio (SDR) technology has been proven in the commercial sector since the early 90's. Today's rapid advancement in mobile telephone reliability and power management capabilities exemplifies the effectiveness of the SDR technology for the modern communications market. SDR technology offers potential to revolutionize satellite transponder technology by increasing science data through-put capability by at least an order of magnitude. While the SDR is adaptive in nature and is "One-size-fits-all" by design, conventional transponders are built to a specific platform and must be redesigned for every new bus. The SDR uses a minimum amount of analog/Radio Frequency (RF) components to up/down-convert the RF signal to/from a digital format. Once analog data is digitized, all processing is performed using hardware logic. Typical SDR processes include; filtering, modulation, up/down converting and demodulation. These innovations have reduced the cost of transceivers, a decrease in power requirements and a commensurate reduction in volume. An additional pay-off is the increased flexibility of the SDR: allowing the same hardware to implement multiple transponder types by altering hardware logic -no change of analog hardware is required -all of which can be ultimately accomplished in orbit.

Sims, Herb↗

NASA NTRS2017

Software Defined Radios - Architectures, Systems and Functions

Software Defined Radio is an industry term describing a method of utilizing a minimum amount of Radio Frequency (RF)/analog electronics before digitization takes place. Upon digitization all other functions are performed in software/firmware. There are as many different types of SDRs as there are data systems. Software Defined Radio (SDR) technology has been proven in the commercial sector since the early 90's. Today's rapid advancement in mobile telephone reliability and power management capabilities exemplifies the effectiveness of the SDR technology for the modern communications market. In contrast the foundations of transponder technology presently qualified for satellite applications were developed during the early space program of the 1960's. SDR technology offers potential to revolutionize satellite transponder technology by increasing science data through-put capability by at least an order of magnitude. While the SDR is adaptive in nature and is "One-size-fits-all" by design, conventional transponders are built to a specific platform and must be redesigned for every new bus. The SDR uses a minimum amount of analog/Radio Frequency components to up/down-convert the RF signal to/from a digital format. Once analog data is digitized, all processing is performed using hardware logic. Typical SDR processes include; filtering, modulation, up/down converting and demodulation. This presentation will show how the emerging SDR market has leveraged the existing commercial sector to provide a path to a radiation tolerant SDR transponder. These innovations will reduce the cost of transceivers, a decrease in power requirements and a commensurate reduction in volume. A second pay-off is the increased flexibility of the SDR by allowing the same hardware to implement multiple transponder types by altering hardware logic - no change of analog hardware is required - all of which can be ultimately accomplished in orbit. This in turn would provide high capability and low cost transponder to programs of all sizes.

Sims, William H.↗

NASA NTRS2017

Software Defined Radios - Architectures, Systems and Functions

Sims, Herb↗

NASA NTRS2018

Development of an Optical Slice for an RF and Optical Software Defined Radio

A key component in the Integrated Radio and Optical Communications project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) is the radio frequency (RF) and optical software defined radio (SDR). A NASA RF SDR might consist of a general purpose processor to run the Space Telecommunications Radio System (STRS) Architecture for radio command and control, a reconfigurable signal processing device such as a field programmable gate array (FPGA) which houses the waveform, and a digital to analog converter for (DAC) transmitting data. Prior to development, SDR architecture trades on how to combine the RF and optical elements were studied. A modular architecture with physically separate RF and optical hardware slices was chosen and the optical slice of an SDR was designed and developed. The Harris AppSTAR("TM") platform, which consists of an FPGA processing platform with a mezzanine card targeted for RF communications, was used as the base platform in prototyping the optical slice. A serially concatenated pulse position modulation (SCPPM) optical waveform was developed. The waveform follows the standard described in the Consultative Committee for Space Data Systems (CCSDS) Optical Communions Coding and Synchronization Red Book. A custom optical mezzanine printed circuit board card was developed at NASA GRC for optical transmission. The optical mezzanine card replaces the DAC, which is used in the transmission of RF signals. This paper describes RF and optical SDR architecture trades, the Harris AppSTAR("TM") platform, the design of the SCPPM waveform, and the development of the optical mezzanine card.

optical communications↗

NASA NTRS2018

Development of an Optical Slice for an RF and Optical Software Defined Radio

A key component in the Integrated Radio and Optical Communications project at the National Aeronautics and Space Administration's (NASA) Glenn Research Center (GRC) is the radio frequency (RF) and optical software defined radio (SDR). A NASA RF SDR might consist of a general purpose processor to run the Space Telecommunications Radio System (STRS) Architecture for radio command and control, a reconfigurable signal processing device such as a field programmable gate array (FPGA) which houses the waveform, and a digital to analog converter (DAC) for transmitting data. Prior to development, SDR architecture trades on how to combine the RF and optical elements were studied. A modular architecture with physically separate RF and optical hardware slices was chosen and the optical slice of an SDR was designed and developed. The Harris AppSTARTM platform, which consists of an FPGA processing platform with a mezzanine card targeted for RF communications, was used as the base platform in prototyping the optical slice. A serially concatenated pulse position modulation (SCPPM) optical waveform was developed. The waveform follows the standard described in the Consultative Committee for Space Data Systems (CCSDS) Optical Communications Coding and Synchronization Red Book. A custom optical mezzanine printed circuit board card was developed at NASA GRC for optical transmission. The optical mezzanine card replaces the DAC, which is used in the transmission of RF signals. This paper describes RF and optical SDR architecture trades, the Harris AppSTAR platform, the design of the SCPPM waveform, and the development of the optical mezzanine card.

Nappier, Jennifer M.↗

NASA NTRS2018

Cognitive Anti-Jamming Satellite-To-Ground Communications on NASA's SCaN Testbed

Machine learning aided cognitive anti-jamming communications is designed, developed and demonstrated on a live satellite-to-ground link. A wideband autonomous cognitive radio (WACR) is designed and implemented as a hardware-in-the- loop (HITL) prototype. The cognitive engine (CE) of the WACR is implemented on a PC while the software-defined radio (SDR) platform utilized two different radios for spectrum sensing and actual communications. The cognitive engine performs spectrum knowledge acquisition over the complete spectrum range available for the SATCOM system operation and learns an anti-jamming communications protocol to avoid both intentional jammers and inadvertent interferers using reinforcement learning. When the current satellite-to-ground link is jammed, the cognitive engine of the ground receiver directs the satellite transmitter to switch to a new channel that is predicted to be jammer-free for the longest possible duration. The end-to-end, closed-loop system was tested on the NASA Space Communications and Navigation (SCaN) Testbed on the International Space Station (ISS). The experimental results demonstrated the feasibility of satellite-to-ground cognitive anti-jamming communications along with excellent anti-jamming capability of machine learning aided cognitive protocols against several different types of jammers.

Jayaweera, Sudharman K.↗

NASA NTRS2018

Cognitive Anti-jamming Satellite-to-Ground Communications on NASA's SCaN Testbed

Machine learning aided cognitive anti-jamming communications is designed, developed and demonstrated on an experimental satellite-to-ground link. A wideband autonomous cognitive radio (WACR) is designed and implemented as a hardware-in the-loop (HITL) prototype. The cognitive engine (CE) of the WACR is implemented on a PC while the software-defined radio (SDR) platform utilized two different radios for spectrum sensing and actual communications. The cognitive engine performs spectrum knowledge acquisition over the complete spectrum range available for the SATCOM system operation and learns an anti-jamming communications protocol to avoid both intentional jammers and inadvertent interferers using reinforcement learning. When the current satellite-to-ground link is jammed, the cognitive engine of the ground receiver directs the satellite transmitter to switch to a new channel that is predicted to be jammer-free for the longest possible duration. The end-to-end, closed-loop system was tested with the NASA's Space Communications and Networking (SCaN) testbed on the International Space Station (ISS). The experimental results demonstrated the feasibility of satellite-to-ground cognitive anti-jamming communications along with excellent anti-jamming capability of machine-learning aided cognitive protocols against several different types of jammers.

Jayaweera, Sudharman K.↗

NASA NTRS2019

Analysis of At-Altitude LTE Power Spectra for C2 Communications for UAS Traffic Management

The National Aeronautics and Space Administration’s (NASA) Unmanned Aircraft Systems Traffic Management (UTM) project works to develop tools and technologies essential for safely enabling civilian low-altitude small Unmanned Aerial Systems (sUAS, also known as drones) operations. This paper presents results of work completed in the paper [1] presented at the 2018 ICNS conference where proposed approaches were explored for evaluating and analyzing sUAS Command and Control (C2) links based on commercial cellular networks. This paper focuses on the UTM Project’s Technology Capability Level 3 (TCL-3) test results which address the communications portion identified within the same paper. A software defined radio (SDR) was flown as a sUAS payload to capture received signal spectrum in Long Term Evolution (LTE) frequency bands of interest. The purpose was to measure the RF environment at UTM altitudes to characterize the interference potential. The SDR payload was flown at various stationary altitudes where the LTE over-the-air complex (I/Q) samples were captured by the SDR and later post-processed. The SDR received inputs through an omnidirectional antenna. The complex samples captured were an aggregate of transmissions received from all line-of-sight (LOS) towers within the geographic area for the specific radio frequency bandwidth the SDR is programmed to capture. Using this approach, the complex samples captured do not distinguish between the various eNodeB's (Long Term Evolution (LTE) transmitting towers). The complex samples were post processed via a Discrete Fourier Transform (DFT) algorithm to view the captured spectrum along with the power levels across the captured LTE bandwidth. This SDR payload process of capturing complex samples was done at two different regions within the US: 1) NASA's Ames Research Center (ARC) in Moffett Field, CA, and 2) Griffiss Airfield in Rome, NY. The data capture at the ARC site was done at two physical locations within the Ames campus where many stationary altitude captures where done as high as 800 ft. above ground level (AGL). The data captured at the Griffiss Airport (also known as the NY Corridor Site) were acquired at one location with three specific stationary altitude levels – {Ground Level (GL), 300 ft., and 400 ft.}. The LTE spectrum power levels were captured for two LTE carriers, AT&T and Verizon, at both sites where their respective spectra and power levels were measured and compared at various altitudes. The overall results show that there is an increase in LTE spectrum power levels at higher altitudes for drones. A detailed analysis of this data and conclusions drawn from the results are presented in this paper.

Kerczewski, Robert J.↗

NASA NTRS2018

TES-8: Advanced Exo-Brake, VR and COM Experiments

The TES-8 was jettisoned from the International Space Station on January 31, 2019. As an orbital laboratory and 8th in on-going series, the design makes use of a standard set of interfaces and safety features that permit rapid re-flight. On this flight, an advanced Exo-Brake is flown with de-orbit targeting capability that will engender sample return capability from LEO platforms. A Virtual Reality data recording system uses stereo imaging and efficient data-compression with an NVIDIA GPU (Graphics Processing Unit) to permit compression and transmission of very large data files. An SDR (Software Defined Radio) will download data to the NEN (Near Earth Network) for the first time - demonstrating potential use in cis-lunar space using S-band. For the first time, a comparison will be made regarding the functionality of the Iridium and Globalstar short burst data modems - as essential communication tools for future nano-sat projects. Lastly, the 7 micro-processors and 4 cameras provide an excellent learning platform for university students and NASA young professionals.

Exo-Brake↗

NASA NTRS2019

The Joint ESA/NASA Galileo/GPS Receiver Onboard the ISS – the GARISS Project

ESA and NASA conducted a joint Galileo/GPS space receiver experiment on-board the International Space Station (ISS). The objectives (Enderle 2017) of the joint project were to demonstrate the robustness of a combined Galileo/GPS waveform uploaded to NASA hardware already operating in the challenging space environment - the SCaN (Space Communications and Navigation) software defined radio (SDR) testbed (FPGA) - on-board the ISS. These activities data included the analysis of the Galileo/GPS signal and on-board Position/Velocity/Time (PVT) performance, processing of the Galileo/GPS raw data (code- and carrier phase) for Precise Orbit Determination (POD), and validate the added value of a space-borne dual GNSS receiver compared to a single-system GNSS receiver operating under the same conditions. This paper will provide a general overview of the Galileo/GPS experiment – called GARISS - on-board the ISS, describe design, test and validation and also the operations of the experiment. Further, the various analysis conducted in the con is joint project and also the results obtained will be presented with a focus on the (Precise) Orbit Determination results.

Enderle, Werner↗

NASA NTRSDate not supplied

NASA Near Earth Network (NEN) DVB-S2 Demonstration Testing for Enhancing Higher Data Rates for CubeSat/Small Satellite Missions at X-/Ka-band

National Aeronautics and Space Administration (NASA) CubeSat/SmallSat missions are moving to higher data rates. Digital Video Broadcast, Satellite Second Generation (DVB-S2) is a communications standard that uses power and bandwidth efficient modulation and coding techniques to deliver performance approaching radio frequency (RF) channel theoretical limits. The Near Earth Network (NEN) will test DVB-S2’s ability to provide higher data rates for CubeSat/SmallSat missions at X-band and Ka-band at Wallops Flight Facility (WFF). The goal is to upgrade the NEN with DVB-S2 to increase science data return for missions and enable support for more CubeSat/SmallSat missions. This paper describes NEN DVB-S2 X-band and Ka-band demonstration objectives, scope, and performance measures as well as NEN channel test configuration. The NEN has planned 2020 tests to demonstrate all modulation and coding schemes in the Consultative Committee for Space Data Systems (CCSDS) DVB-S2 standard over X-band and Ka-band. A link analysis study for the trade-offs among achievable data rates, modulations, codes, spacecraft antenna sizes and power amplifiers (PA) is provided. This paper identifies Commercial off-the-shelf (COTS) CubeSat/SmallSat X-band and Ka-band communication systems and discusses low cost DVB-S2 X-band software defined radio (SDR) transmitter development concepts and implementation with a practical system for CubeSats/SmallSats.

Yen Wong↗