Search NASA⌕ Search

SEARCH · Search NASA

Results for “spall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Solutions for discharge chamber sputtering and anode deposit spalling in small mercury ion thrusters

Small electron bombardment mercury ion thrusters are considered for attitude-control and station-keeping operations in the case of earth synchronous satellites. The required operational lifetimes of the order of 20,000 hours could present problems because of the occurrence of sputter erosion of thruster discharge chamber components. The investigation reported is concerned with a study of these problems and the development of approaches for overcoming them.

Power, J. L.↗
NASA NTRS1980

A precoat prevents ceramic stopoffs from spalling

Nickel-alloy precoat applied with plasmagun improves adhesion of ceramic materials applied to protect areas from unintentional brazing. Metal surface should be grit-blasted before precoating. Coating does not interfere with brazing or contaminate vacuum pumping systems.

Brennan, A.↗
NASA NTRS1983

Correlation of compressive stress with spalling of plasma sprayed ceramic materials

Ceramics on metal substrates for potential use as high temperature seals or other applications are exposed to forces originating from differences in thermal expansion between the ceramic and the metal substrate. This report develops a relationship between the difference in expansion of the ceramic and the substrate, defines conditions under which shear between the ceramic and the substrate occurs, and those under which bending forces are produced in the ceramic. The off-axis effect of compression forces resulting from high temperature plastic flow of the ceramic producing buckling of the ceramic is developed. Shear is associated with the edge or boundary stresses on the component while bending is associated with the distortion of an interior region. Both modes are significant in predicting life of the ceramic.

Mullen, R. L.↗
NASA NTRS1983

Correlation of compressive and shear stress with spalling of plasma-sprayed ceramic materials

Ceramics on metal substrates for potential use as high temperature seals or other applications are exposed to forces originating from differences in thermal expansion between the ceramic and the metal substrate. This report develops a relationship between the difference in expansion of the ceramic and the substrate, defines conditions under which shear between the ceramic and the substrate occurs, and those under which bending forces are produced in the ceramic. The off-axis effect of compression forces resulting from high temperature plastic flow of the ceramic producing buckling of the ceramic is developed. Shear is associated with the edge or boundary stresses on the component while bending is associated with the distortion of an interior region. Both modes are significant in predicting life of the ceramic. Previously announced in STAR as N83-27016

Mullen, R. L.↗
NASA NTRS2001

Investigation into Spectroscopic Techniques for Thermal Barrier Coating Spall Detection

Spectroscopic methods are proposed for detection of thermal barrier coating (TBC) spallation from engine hot zone components. These methods include absorption and emission of airborne marker species originally embedded in the TBC bond coat. In this study, candidate marker materials for this application were evaluated. Thermochemical analysis of candidate marker materials combined with additional constraints such as toxicity and uniqueness to engine environment, provided a short list of four potential species: platinum, copper oxide, zinc oxide. and indium. The melting point of indium was considered to be too low for serious consideration. The other three candidate marker materials, platinum, copper oxide, and zinc oxide were placed in a high temperature furnace and emission and absorption properties were measured over a temperature range from 800-1400 C and a spectral range from 250 to 18000 nm. Platinum did not provide the desired response, likely due to the low vapor Pressure of the metallic species and the low absorption of the oxide species. It was also found, however. that platinum caused a broadening of the carbon dioxide absorption at 4300 nm. The nature of this effect is not known. Absorption and emission caused by sodium and potassium impurities in the platinum were found in the platinum tests. Zinc oxide did not provide the desired response, again, most likely due to the low vapor pressure of the metallic species and the low absorption of the oxide species. Copper oxide generated two strongly temperature dependent absorption peaks at 324.8 and 327.4 nm. The melting point of copper oxide was determined to be too low for serious consideration as marker material.

deGroot, Wim↗
DOE OSTI2021

Sonic Lift-off of GaAs-based Solar Cells with Reduced Surface Facets

Spalling has been proposed as a promising kerfless technique for slicing thin wafers and devices, enhancing the wafer yield from an ingot by reducing kerf-losses and enabling substrate reuse for the case of costly devices. The main challenge of spalling is to control the roughness and thickness variation of the spalled wafers that can be as high as 100% of the wafer thickness. Here, we have shown previously that the thickness variations are largely influenced by the interaction of the crack front with its own reflected waves. Herein we show that through Sonic Lift-off we can offer a modification to standard spalling technologies that minimizes the interaction of reflected waves with the crack front during lift-off of GaAs(100)-based solar cells. We show that the average surface facets amplitude can be reduced by 96% while obtaining a high quality bulk with no discernible residual strain as measured by PL. The resulting spalling depth can easily be tuned from 100 µm to less than 15µm. The electrical characterization of the Sonic lift-off cell shows no degradation of the VOC and a power conversion within 99% relative of a non-spalled baseline.

42 ENGINEERING↗
DOE OSTI2023

The effect of microstructure on the dynamic shock response of 1045 steel

Herein, the effect of microstructure on the shock response of 1045 steel is investigated via plate impact experiments and postmortem characterization. Three unique microstructures are explored: ferrite-pearlite, martensite, and ferrite with spheroidal cementite (i.e. spheroidized). Two spall recovery experiments, at approximate peak pressures of 3.2 and 3.5 GPa, are conducted to assess the Hugoniot elastic limit (HEL), spall strength, and damage morphology of the various microstructures. The ferrite-pearlite and martensite microstructures exhibit continuous yielding at both quasi-static and dynamic rates, while the spheroidized condition displays discontinuous yielding. Discontinuous yielding of the spheroidized microstructure is attributed to a combined low initial dislocation density coupled with a low dislocation nucleation rate. The spall strength of ferrite-pearlite is consistently lower than the spheroidized microstructure, attributed to elongated cementite that is more susceptible to cracking than more spherical cementite precipitates. Despite a high density of boundaries, martensite exhibits the highest spall strength. A large percentage of the boundaries within the martensite microstructure are found to be low energy (i.e. Σ3 or low angle), and are thus less susceptible to spall damage. Overall, the high spall strength of martensite is likely linked to traditional strengthening mechanisms that limit dislocation motion.

36 MATERIALS SCIENCE↗