Search NASA⌕ Search

SEARCH · Search NASA

Results for “spark ignition engines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1932

The Use of Large Valve Overlap in Scavenging a Supercharged Spark-ignition Engine Using Fuel Injection

This investigation was conducted to determine the effect of more complete scavenging on the full throttle power and the fuel consumption of a four-stroke-cycle engine. The NACA single-cylinder universal test engine equipped with both a fuel-injection system and a carburetor was used. The engine was scavenged by using a large valve overlap and maintaining a pressure in the inlet manifold of 2 inches of mercury above atmospheric. The maximum valve overlap used was 112 degrees. Tests were conducted for a range of compression ratios from 5.5 to 8.5. Except for variable speed tests, all tests were conducted at an engine speed of 1,500 r.p.m. The results of the tests show that the clearance volume of an engine can be scavenged by using a large valve overlap and about 2 to 5 inches of mercury pressure difference between the inlet and exhaust valve. With a fuel-injection system when the clearance volume was scavenged, a b.m.e.p. of over 185 pounds per square inch and a fuel consumption of 9.45 pound per brake horsepower per hour were obtained with a 6.5 compression ratio. An increase of approximately 10 pounds per square inch b.m.e.p. was obtained with a fuel-injection system over that with a carburetor.

Schey, Oscar W↗
NASA NTRS1934

Performance of a Fuel-Injection Spark-Ignition Engine Using a Hydrogenated Safety Fuel

This report presents the performance of a single-cylinder test engine using a hydrogenated safety fuel. The safety fuel has a flash point of 125 degrees f. (Cleveland open-dup method), which is high enough to remove most of the fire hazard, and an octane number of 95, which permits higher compression ratios to be used than are permissible with most undoped gasolines.

Schey, Oscar W↗
NASA NTRS1939

The Influence of Directed Air Flow on Combustion in Spark-Ignition Engine

The air movement within the cylinder of the NACA combustion apparatus was regulated by using shrouded inlet valves and by fairing the inlet passage. Rates of combustion were determined at different inlet-air velocities with the engine speed maintained constant and at different engine speeds with the inlet-air velocity maintained approximately constant. The rate of combustion increased when the engine speed was doubled without changing the inlet-air velocity; the observed increase was about the same as the increase in the rate of combustion obtained by doubling the inlet-air velocity without changing the engine speed. Certain types of directed air movement gave great improvement in the reproducibility of the explosions from cycle to cycle, provided that other variables were controlled. Directing the inlet air past the injection valve during injection increased the rate of burning.

Rothrock, A M↗
NASA NTRS1940

Measurement of Knock Characteristics in Spark-ignition Engines

This paper presents a discussion of three potential sources of error in recording engine knocking which are: the natural oscillation of the membrane, the shock process between test contacts, and the danger of burned contacts. Following this discussion, the paper calls attention to various results which make the bouncing-pin indicator appear fundamentally unsuitable for recording knock phenomena.

Schutz, R↗
DOE OSTI2021

Cycle-to-cycle variability in spark-assisted compression ignition engines near optimal mean combustion phasing

Stoichiometric spark-assisted compression ignition (SACI) combustion with exhaust gas recirculation (EGR) dilution has demonstrated higher part-load thermal efficiencies compared to spark-ignited engines, while maintaining ultra-low tailpipe emissions. However, SACI is often characterized by high cyclic variability in heat release or torque output, which poses a challenge to its implementation in light-duty vehicles. This paper presents an experimental investigation of cyclic variability in stoichiometric SACI combustion under EGR-dilute conditions, while maintaining mean combustion phasing (θ 50 ) near optimal timing for thermal efficiency. The present work focuses on SACI conditions where the flame-based heat release fraction is between approximately 10% and 40% of the overall heat release, and therefore contributes significantly to the combustion process. For the SACI conditions examined, the variability in θ 50 was driven by variability in autoignition timing, which in turn correlated with the start of measurable heat release (θ 02 ). High variability in θ 50 caused unstable work output due to very late combustion with poor or no end-gas autoignition. The use of a high ignition energy dual-coil offset ignition system had negligible impact in reducing θ 50 variability. Analysis of experimental data from close to 1000 operating conditions showed that the magnitude of θ 50 variability correlates with the flame-based heat release fraction ([Formula: see text]), for a large range of intake pressures, spark timings and exhaust gas recirculation levels. For the SACI conditions examined, combustion phasing variability was largely determined by flame-based combustion and particularly the initial flame formation (θ IGN-02 ), and minimally by the end-gas autoignition heat release. The analysis also demonstrated that θ 50 variability is amplified as the contribution of the flame to the overall heat release increases.

Engineering↗
DOE OSTI2022

Alkyl dialkoxyalkanoates as bioderived, high cetane diesel fuels

A fuel for an internal combustion engine includes a C 5 to C 30 dialkoxyalkanoate corresponding to formula (I), wherein the R 1 group is —H or a —CH 3 group, the R 2 and R 2 ′ groups are alkyl groups independently selected to have 1 to 9 carbon atoms; and the R 3 group is selected to have 1 to 9 carbon atoms. The compounds described herein may be used as neat fuels or mixed fuels (with diesel, biodiesel, jet fuel, marine fuel or other fuel compounds) in autoignition or spark ignition engines, such as diesel engines, gasoline (spark ignition) engines, MCCI, Homogeneous Charge Compression Ignition (HCCI) engines, or more generally in Low-Temperature Gasoline Combustion (LTGC) engines (using gasoline-like fuels), that have the high-efficiency advantages of HCCI but can operate with some level of charge inhomogeneities. Methods of making these compounds are environmentally friendly and can be done in a continuous manner.

Myllenbeck, Nicholas↗
DOE OSTI2020

Impact of Selected High-Performance Fuel Blends on Three-Way Catalyst Light Off under Synthetic Spark-Ignition Engine-Exhaust Conditions

The U.S. Department of Energy funded Co-Optimization of Fuels and Engines initiative aims to simultaneously develop advanced engines along with high-performance fuels to reduce petroleum consumption. The engine exhaust of spark-ignited light-duty vehicles contains pollutants such as nitrogen oxides, carbon monoxide (CO), and non-methane organic gases. When operated above their “light-off” temperature, three-way catalysts (TWCs) efficiently control the emissions of these pollutants from the vehicle exhaust. However, below the catalyst light-off temperature, during cold start, the TWCs are not effective. Thus, the stringent environmental regulations necessitate cold-start compliance of advanced engines operating on novel fuels for commercialization. Exhaust composition strongly impacts the effectiveness of TWCs. Hence, ensuring that the high-performance fuels under consideration do not have detrimental effects on current emissions control technology is necessary. To mitigate cold-start emissions, a low light-off temperature of the fuel on the TWC is desirable. As real-world fuels are multicomponent blends, we conducted investigations into the light-off behavior of representative fuel mixtures on a three-mode redox-aged commercial TWC under synthetic engine-exhaust conditions. The high-performance fuels in this study included 10–30% volumetric levels of ethanol, isobutanol, diisobutylene, and an aromatic mixture. Each of these high-performance fuel components was mixed into a gasoline surrogate blendstock for oxygenate blending (BOB). Our results showed that aromatics and alkenes in the surrogate BOB inhibit low-temperature reactivity of alkanes, alcohols, and CO on the TWC and dominate the blend light-off behavior. All the high-performance fuel blends had a very similar light-off behavior to the surrogate gasoline BOB, indicating that blending up to 30% (by vol.) of high-performance blendstocks in a gasoline base fuel can potentially reduce greenhouse gas emissions through improved engine efficiency and petroleum displacement without jeopardizing the ability to meet emissions regulations. While some high-performance blendstocks demonstrated lower light-off temperatures than a surrogate gasoline blend, taking advantage of the higher catalytic reactivity of these blendstocks to reduce cold-start emissions would require reducing the aromatic content in petroleum-based market fuels.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1982

Free-piston Stirling hydraulic engine and drive system for automobiles

The calculated fuel economy for an automotive free piston Stirling hydraulic engine and drive system using a pneumatic accumulator with the fuel economy of both a conventional 1980 spark ignition engine in an X body class vehicle and the estimated fuel economy of a 1984 spark ignition vehicle system are compared. The results show that the free piston Stirling hydraulic system with a two speed transmission has a combined fuel economy nearly twice that of the 1980 spark ignition engine - 21.5 versus 10.9 km/liter (50.7 versus 25.6 mpg) under comparable conditions. The fuel economy improvement over the 1984 spark ignition engine was 81 percent. The fuel economy sensitivity of the Stirling hydraulic system to system weight, number of transmission shifts, accumulator pressure ratio and maximum pressure, auxiliary power requirements, braking energy recovery, and varying vehicle performance requirements are considered. An important finding is that a multispeed transmission is not required. The penalty for a single speed versus a two speed transmission is about a 12 percent drop in combined fuel economy to 19.0 km/liter (44.7 mpg). This is still a 60 percent improvement in combined fuel economy over the projected 1984 spark ignition vehicle.

Beremand, D. G.↗
DOE OSTI2021

Numerical investigation of a fueled pre-chamber spark-ignition natural gas engine

Pre-chamber spark-ignition (PCSI) is a leading advanced ignition concept for internal combustion engines with the potential to enable diesel-like efficiency in medium-duty/heavy-duty (MD/HD) natural gas (NG) engines. By leveraging distributed ignition sources from multiple turbulent jets, the PCSI technology can deliver extremely short combustion duration in ultra-lean mixtures and significantly improve the engine thermal efficiency. However, in the automotive industry there is a lack of adequate science base and predictive simulation tools required for commercial development of PCSI engines. Here, in this study, Reynolds-Average Navier-Stokes simulations are carried out to describe the combustion process in lean-burn NG engines, focusing on the combustion modeling approach. Two combustion models, multi-zone well-stirred reactor (MZ-WSR) and G-equation, are used to simulate the combustion process in an MD NG engine equipped with a fueled-PCSI system for four operating conditions close to the lean operating limit. A skeletal chemical mechanism and a laminar flame speed tabulation are used to compute the combustion accurately. Simulation results are compared with experimental data regarding measured cylinder pressure, heat release rate, and combustion duration. By dividing the PCSI combustion process into four distinct phases, the difference between the two models’ results for each phase is analyzed in detail. The MZ-WSR model overestimates the combustion duration for early flame kernel growth in the pre-chamber due to the lack of a specific formulation to take turbulence-chemistry interaction into account. Despite the prolonged combustion duration and low pressure built-up inside the pre-chamber, the model matches the combustion rate in the main-chamber. In contrast, the G-equation model delivers good agreements for the pre-chamber combustion and turbulent jet-driven combustion processes. However, the model starts to underestimate the combustion rate in the main-chamber, especially under ultra-lean mixture conditions. Finally, improvements are needed for both models to simulate the later combustion stage that occurred in the near-wall regions.

33 ADVANCED PROPULSION SYSTEMS↗