Search NASA⌕ Search

SEARCH · Search NASA

Results for “stacking sequences”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Compression fatigue behavior of composites in the presence of delaminations

Three different stacking sequences of a 64-ply layup were tested in an experimental investigation of the effect of idealized imbedded delaminations on the compression fatigue behavior of quasi-isotropic T300/5208 graphite-epoxy laminates. Postfailure examination of specimen cross sections revealed the absence of any fiber microbuckling, suggesting that the predominant failure mode was the propagation of imbedded delaminations in the tab region. One- and two-dimensional delaminations, respectively located across the entire width below the surface ply and buried one or four plies below the surface, were considered. A novel procedure employing minute, laser-drilled holes was successfully used in extending the application of diidobutane-enhaced radiography to buried delaminations.

Ramkumar, R. L.↗
NASA NTRS1983

Fracture behavior of hybrid composite laminates

The tensile fracture behavior of 15 center-notched hybrid laminates was studied. Three basic laminate groups were tested: (1) a baseline group with graphite/epoxy plies, (2) a group with the same stacking sequence but where the zero-deg plies were one or two plies of S-glass or Kevlar, and (3) a group with graphite plies but where the zero-deg plies were sandwiched between layers of perforated Mylar. Specimens were loaded linearly with time; load, far field strain, and crack opening displacement (COD) were monitored. The loading was stopped periodically and the notched region was radiographed to reveal the extent and type of damage (failure progression). Results of the tests showed that the hybrid laminates had higher fracture toughnesses than comparable all-graphite laminates. The higher fracture toughness was due primarily to the larger damage region at the ends of the slit; delamination and splitting lowered the stress concentration in the primary load-carrying plies. A linear elastic fracture analysis, which ignored delamination and splitting, underestimated the fracture toughness. For almost all of the laminates, the tests showed that the fracture toughness increased with crack length. The size of the damage region at the ends of the slit and COD measurements also increased with crack length.

Kennedy, J. M.↗
NASA NTRS1983

Dynamic-mechanical response of graphite/epoxy composite laminates and neat resin

Dynamic mechanical measurement results are presented for the case of carbon fiber-reinforced, epoxy matrix composite laminates subjected to loading perpendicular to the lamination plane, as well as for neat epoxy resin under the same conditions, where temperatures ranged between 20 and 200 C and deformation levels lie within the linear viscoelastic region. In-phase and out-of-phase stiffnesses are found to become superposed, forming master curves that cover a 12-decade frequency range. The application of a master curve scaling procedure shows that the in-phase stiffness has the same shape, and out-of-phase stiffness has the same dispersion, for all laminates irrespective of stacking sequence and are, in turn, nearly identical to those for the neat epoxy resin. An empirical function is found for the relaxation modulus which, when converted to a dynamic modulus, yields good overall agreement for both of the dynamic stiffness components as a function of frequency.

Yang, P.↗
NASA NTRS1983

Modeling stiffness loss in boron/aluminum laminates below the fatigue limit

Boron/aluminum can develop significant internal matrix cracking when fatigued. These matrix cracks can result in a 40 percent secant modulus loss in some laminates, even when fatigued below the fatigue limit. It is shown that the same amount of fatigue damage will develop during stress or strain-controlled tests. Stacking sequence has little influence on secant modulus loss. The secant modulus loss in unidirectional composites is small, whereas the losses are substantial in laminates containing off-axis plies. A simple analysis is presented that predicts unnotched laminate secant modulus loss due to fatigue. The analysis is based upon the elastic modulus and Poisson's ratio of the fiber and matrix, fiber volume fraction, fiber orientations, and the cyclic-hardened yield stress of the matrix material. Excellent agreement was achieved between model predictions and experimental results. With this model, designers can project the material stiffness loss for design load or strain levels and assess the feasibility of its use in stiffness-critical parts. Previously announced in STAR as N82-24298

Johnson, W. S.↗
NASA NTRS1984

Effect of microcracks on the thermal expansion of composite laminates

A finite element analysis was used to quantitatively predict the effect of matrix microcracks in the 90 deg plies of graphite/epoxy composites on the coefficient of thermal expansion in the 0 deg direction, alpha (y) (perpendicular to the cracks). Results were generated for (0m/90n)s, (0/+ or 45/90)s and (0/90/ + or - 45)s graphite/epoxy laminate configurations. Analytical predictions were compared with experimental results for the two quasi-isotropic laminate configurations. Both analytical and experimental results showed that microcracks reduced the effective stiffness of the 90 deg plies, thus causing the laminates, thermal response to be more like that of a (0) laminate. The change in alpha(y) was a function of lamina material properties, microcrack density, fiber orientation, and stacking sequence. A combination of classical lamination theory and finite element analysis was used to predict the effect of microcracks in both the 90 deg and 0 deg plies. Analytical results showed that the addition of microcracks in the 0 deg plies do affect alpha(y), but to a lesser extent than those in the 90 deg plies.

Bowles, D. E.↗
NASA NTRS1984

A comparison of several methods of calculating fracture toughness from composite laminate test data

Critical fracture toughness was determined by two different techniques for graphite/epoxy laminates of three stacking sequences and several thicknesses. Critical fracture toughness was determined by a finite element stress analysis of a center-cracked tension specimen which yielded the stress intensity factor as a function of specimen thickness and applied load. As an alternative approach the critical strain energy release rate was determined from the compliance calibration technique. Test results from both procedures are compared and discussed.

Harris, C. E.↗
NASA NTRS1984

Composite Fracture Toughness and Impact Characterization

The basic threat to the more widespread use of composites in aircraft primary structure is the problem of residual strength in the presence of damage. Specific problem areas that need to be addressed include the following: (1) modeling/understanding composite failure (impact: relate strain energy release rate to strain-to-failure, open hole compression: relate shear crippling to strain-to-failure, and account for variables such as thickness and stacking sequence); (2) micromechanics models; (3) consider the use of hybrid combinations, both interply and intraply, using graphite, Kevlar, and glass; and (4) modeling/understanding the role of the interface. Solving these problems involves a multidisciplinary approach including dynamics, structural stability, composite mechanics, and fracture mechanics.

Source record↗
NASA NTRS1985

Thermal expansion of selected graphite reinforced polyimide-, epoxy-, and glass-matrix composite

The thermal expansion of three epoxy-matrix composites, a polyimide-matrix composite and a borosilicate glass-matrix composite, each reinforced with continuous carbon fibers, has been measured and compared. The expansion of a composite with a rubber toughened epoxy-matrix and P75S carbon fibers was very different from the expansion of two different single phase epoxy-matrix composites with P75S fibers although all three had the same stacking sequence. Reasonable agreement was obtained between measured thermal-expansion data and results from classical laminate theory. The thermal expansion of a material may change markedly as a result of thermal cycling. Microdamage, induced by 250 cycles between -156 C and 121 C in the graphite/polyimide laminate, caused a 53 percent decrease in the coefficient of thermal expansion. The thermal expansion of the graphite/glass laminate was not changed by 100 thermal cycles from -129 C to 38 C; however, a residual strain of about 10 x 10 to the minus 6 power was measured for the laminate tested.

Tompkins, S. S.↗
NASA NTRS1983

Determination of interlaminar fracture toughness and fracture mode dependence of composites using the edge delamination test

Edge delamination testing has been conducted in order to determine the mixed mode interlaminar fracture toughness of unnotched (+, -35/0/90)s and (0/+, -35/90)s laminates with graphite fibers and epoxy matrices, with or without elastomer additives. Although the two stacking sequences were chosen so that the total strain energy release rates were equal, the percentages of crack opening and shear mode energy release rates were found to vary widely between the layups. Plots of interlaminar fracture toughness as a function of crack opening energy release rate percentage have been drawn to generate delamination failure criteria which reflect the observed fracture mode dependence.

Obrien, T. K.↗
NASA NTRS1983

Detection of acoustic emission from composite laminates using PVF2 transducers

Polyvinylidene fluoride (PVF2), a semicrystalline polymer exhibiting piezoelectricity, is presently used as a sensing transducer in acoustic emission (AE) monitoring of several different composite laminate materials in order to obtain both quasi-static and fatigue loading results. AE signals obtained from PVF2 transducers are compared with those obtained by standard AE sensors. It is noted that PVF2 transducers may, through the application of spectral signal analysis, be able to distinguish between two distinct failure modes which have been observed in two composite laminates of the same material, but employing different lamina stacking sequences.

Stiffler, R.↗
NASA NTRS1985

Importance of anisotropic bending stiffnesses on buckling of symmetrically laminated composite plates loaded in compression

The differential equation governing buckling of symmetrically laminated composite plates loaded in compression is presented in nondimensional form. From this equation, nondimensional material coefficients are obtained and a nondimensional parameter is presented that is used to assess when anisotropic bending stiffnesses can be neglected in a buckling analysis. Results obtained using finite element analyses are presented that show how boundary conditions, aspect ratio, fiber orientation, stacking sequence, and thickness affect the importance of the anisotropic bending stiffnesses.

Nemeth, M. P.↗
NASA NTRS1985

Postbuckling of flat unstiffened graphite-epoxy plates loaded in shear

An experimental and analytical study was conducted of the postbuckling response and failure characteristics of 8-, 16-, and 24-ply unstiffened graphite/epoxy plates under shear loading, including orthotropic, quasi-orthotropic, entirely +, -45 deg ply, and (0/90)s-class plates. Postbuckling stiffness is noted to be influenced by the stacking sequence and by the inplane boundary condition imposed on the test section by a picture frame test fixture. The ratio of failure load to buckling load was higher for specimens that had higher width-to-thickness ratios. It is noted that high displacement gradients may induce transverse shear stresses, and that delamination was the failure mechanism for many of the 8-ply specimens. An adhesive failure between the composite specimen and metal edge reinforcements initiated failure of the 16- and 24-ply specimens.

Rouse, M.↗
NASA NTRS1985

On the use of crack-tip-opening displacement to predict the fracture strength of notched graphite/epoxy laminates

Using the center-cracked tension specimen geometry, the fracture strength of notched graphite/epoxy laminates is measured experimentally. Four replicate tests are conducted for a variety of laminate-stacking sequences, thicknesses, and notch lengths. Extensive notch-tip damage prior to fracture is characteristic of most laminates. The values of critical crack-tip-opening displacement (CTOD) are calculated from values of crack-opening displacement measured at the notch center line at failure and are found to be independent of notch size for the laminates studied. A Dugdale (1950) model is used along with the estimated CTOD to predict notched laminate strength.

Harris, C. E.↗
NASA NTRS1985

Fatigue Damage in Notched Composite Laminates Under Tension-Tension Cyclic Loads

The results are given of an investigation to determine the damage states which develop in graphite epoxy laminates with center holes due to tension-tension cyclic loads, to determine the influence of stacking sequence on the initiation and interaction of damage modes and the process of damage development, and to establish the relationships between the damage states and the strength, stiffness, and life of the laminates. Two quasi-isotropic laminates were selected to give different distributions of interlaminar stresses around the hole. The laminates were tested under cyclic loads (R=0.1, 10 Hz) at maximum stresses ranging between 60 and 95 percent of the notched tensile strength.

Stinchcomb, W. W.↗
NASA NTRS1985

Fracture of thick graphite/epoxy laminates with part-through surface flaws

Fracture behavior of tensile specimens containing through-the-thickness flaws and part-through semi-elliptic surface flaws was investigated. The material was T300/5208 graphite/epoxy, with a stacking sequence 0/+ or - 45/90 sub ns. Laminate thicknesses ranged from 8 to 120 plies. Fracture toughness for specimens with through-the-thickness flaws was a function of laminate thickness. Fracture toughness was also independent of crack size. Fracture toughness for the thick laminates was also independent of specimen geometry (center-cracked tension specimen, compact tension specimen, and three-point bend specimen). Using the asymptotic value of facture toughness and linear elastic isotropic fracture mechanics, the notched strength of tensile specimens with semi-elliptic surface flaws was predicted. The strength ratio is a function of the flaw depth (a/t) and flaw aspect (a/c) ratios. Comparisons between predicted and experimental strengths are good for large values of a/t. The notched strength of filament wound graphite/epoxy tensile specimens with part-through surface flaws was also predicted.

Morris, D. H.↗
NASA NTRS1986

Sublaminate analysis of interlaminar fracture in composites

A simple analysis method based upon a transverse shear deformation theory and a sublaminate approach is utilized to analyze a mixed-mode edge delamination specimen. The analysis provides closed form expressions for the interlaminar shear stresses ahead of the crack, the total energy release rate, and the energy release rate components. The parameters controlling the behavior are identified. The effect of specimen stacking sequence and delamination interface on the strain energy release rate components is investigated. Results are compared with a finite element simulation for reference. The simple nature of the method makes it suitable for preliminary design analyses which require a large number of configurations to be evaluated quickly and economically.

Armanios, E. A.↗
NASA NTRS1986

Temperature dependent nonlinear metal matrix laminae behavior

An analytical method is described for computing the nonlinear thermal and mechanical response of laminated plates. The material model focuses upon the behavior of metal matrix materials by relating the nonlinear composite response to plasticity effects in the matrix. The foundation of the analysis is the unidirectional material model which is used to compute the instantaneous properties of the lamina based upon the properties of the fibers and matrix. The unidirectional model assumes that the fibers properties are constant with temperature and assumes that the matrix can be modelled as a temperature dependent, bilinear, kinematically hardening material. An incremental approach is used to compute average stresses in the fibers and matrix caused by arbitrary mechanical and thermal loads. The layer model is incorporated in an incremental laminated plate theory to compute the nonlinear response of laminated metal matrix composites of general orientation and stacking sequence. The report includes comparisons of the method with other analytical approaches and compares theoretical calculations with measured experimental material behavior. A section is included which describes the limitations of the material model.

Barrett, D. J.↗
NASA NTRS1986

Fracture of thick laminated composites

The fracture of thick laminated graphite/epoxy composites has been the subject of an extensive research program. The program was divided into three major areas of investigation which included laminate thickness, laminate stacking sequence, and part-through surface flaws. The results from this program are reviewed with emphasis placed on their applicability to the design of thick laminated composite structures.

Harris, C. E.↗