Search NASA⌕ Search

SEARCH · Search NASA

Results for “stitched composite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Blended-Wing-Body (BWB) Fuselage Structural Design for Weight Reduction

Structural analysis and design of efficient pressurized fuselage configurations for the advanced Blended-Wing-Body (BWB) flight vehicle is a challenging problem. Unlike a conventional cylindrical pressurized fuselage, stress level in a box type BWB fuselage is an order of magnitude higher, because internal pressure primarily results in bending stress instead of skin-membrane stress. In addition, resulting deformation of aerodynamic surface could significantly affect performance advantages provided by lifting body. The pressurized composite conformal multi-lobe tanks of X-33 type space vehicle also suffered from similar problem. In the earlier BWB design studies, Vaulted Ribbed Shell (VLRS), Flat Ribbed Shell (FRS); Vaulted shell Honeycomb Core (VLHC) and Flat sandwich shell Honeycomb Core (FLHC) concepts were studied. The flat and vaulted ribbed shell concepts were found most efficient. In a recent study, a set of composite sandwich panel and cross-ribbed panel were analyzed. Optimal values of rib and skin thickness, rib spacing, and panel depth were obtained for minimal weight under stress and buckling constraints. In addition, a set of efficient multi-bubble fuselage (MBF) configuration concept was developed. The special geometric configuration of this concept allows for balancing internal cabin pressure load efficiently, through membrane stress in inner-stiffened shell and inter-cabin walls, while the outer-ribbed shell prevents buckling due to external resultant compressive loads. The initial results from these approximate finite element analyses indicate progressively lower maximum stresses and deflections compared to the earlier study. However, a relative comparison of the FEM weight per unit floor area of the segment unit indicates that the unit weights are still relatively higher that the conventional B777 type cylindrical or A380 type elliptic fuselage design. Due to the manufacturing concern associated with multi-bubble fuselage, a Y braced box-type fuselage alternative with special resin-film injected (RFI) stitched carbon composite with foam-core was designed by Boeing under a NASA research contract for the 480 passenger version. It is shown that this configuration can be improved to a modified multi-bubble fuselage which has better stress distribution, for same material and dimension.

Mukhopadhyay, V.↗
NASA NTRS1993

Effects of temperature and humidity cycling on the strengths of textile reinforced carbon/epoxy composite materials

Results are presented from an experimental evaluation of the combined effects of temperature and humidity cycling on AS4/3501-6 composites (unstitched, Kevlar 29 stitched, and S-2 glass stitched uniweave fabric) and AS4/E905L composites (2-D, S-2 glass stitched 2-D, and 3-D braided fabric). The AS4/3501-6 uniweave material had a quasi-isotropic layup, whereas the AS4/E905L materials were braided in a (+/-30 deg/0 deg)(sub s) orientation. Data presented include compression strengths and compression-compression fatigue results for uncycled composites and cycled composites (160, 480, 720, and 1280 cycles from 140 deg F at 95 percent relative humidity to -67 deg F). To observe the presence of microcracking within the laminates, photomicrographs were taken of each material type at the end of each cycling period. Microcracks were found to be more prevalent within stitched laminates, predominantly around individual stitches. The glass stitched laminates showed significant microcracking even before cycling. Less microcracking was evident in the Kevlar stitched materials, whereas the unstitched uniweave material developed microcracks only after cycling. The 3-D braid did not develop microcracks. The static compression strengths of the unstitched and Kevlar stitched uniweave materials were degraded by about 10 percent after 1280 temperature/humidity cycles, whereas the reduction in compression strength for the glass stitched uniweave was less than 3 percent. The reduction in compression strength for the glass stitched 2-D braid was less than 8 percent. The unstitched 2-D and 3-D braids did not lose strength from temperature/humidity cycling. The compression-compression fatigue properties of all six material types were not affected by temperature/humidity cycling.

Cano, Roberto J.↗
NASA NTRS1988

Low cost damage tolerant composite fabrication

The resin transfer molding (RTM) process applied to composite aircraft parts offers the potential for using low cost resin systems with dry graphite fabrics that can be significantly less expensive than prepreg tape fabricated components. Stitched graphite fabric composites have demonstrated compression after impact failure performance that equals or exceeds that of thermoplastic or tough thermoset matrix composites. This paper reviews methods developed to fabricate complex shape composite parts using stitched graphite fabrics to increase damage tolerance with RTM processes to reduce fabrication cost.

Palmer, R. J.↗
NASA NTRSDate not supplied

Out-of-plane behavior of selectively stitched curved beams subjected to four-point bending

Through-the-thickness stitching can be used to provide a pathway to reduce interlaminar damage in laminated polymer composites. To decrease the amount of stitching, a selective stitching process is necessary to reduce the total manufacturing time in stitched polymer composites. In this study, L-shaped laminates are stitched in the radius section to arrest out-of-plane damage that can occur when subjected to four-point bending loads. A cohesive zone finite element model of the L-shaped laminate was developed. An embedded spring element approach was used to represent the through-the-thickness reinforcements within the finite element model. Specimens with stitches in the radius region of the L-shaped laminate were found to have greater maximum loads before failure. The through-the-thickness stitches are observed to locally reduce the radial stresses in the radius region of the L-shaped laminate, which results in delamination growth away from the radius centerline and greater load-carrying capability.

Stitched Composites↗
NASA NTRS1993

Effects of thermal and moisture cycling on the internal structure of stitched RTM laminates

Conventional aerospace composites are strong and stiff in the directions parallel to the carbon fibers, but they are prone to delaminations and damage in the through-the-thickness directions. Recent research has shown that substantial improvements in damage tolerance are obtained from textile composites with Z-direction reinforcement provided by stitching, weaving, or braiding. Because of the mismatch in thermal and moisture expansion properties of the various material components, there is a potential for microcracks to develop in the resin matrix. These cracks can form to relieve the mechanical stresses that are generated during curing or in-service temperature cycles.

Walker, Jeff↗
NASA NTRS2019

GOES-R Solar UltraViolet Imager Extended Coronal Imaging

GOES-16 and GOES-17 each hosts a Solar UltraViolet Imager (SUVI) that images the Sun in six extreme ultraviolet (EUV) wavelengths: 9.4 nm, 13.1nm, 17.1nm, 19.5nm, 28.4nm, and 30.4nm. The SUVI is nominally Sun-pointed and has a four-minute imaging sequence covering all the channels and meeting the dynamic range requirements. Based on the SUVI capabilities observed on-orbit, a campaign to image the extended solar corona was undertaken in 2018. This was performed by off-pointing the SUVI line-of-sight to the left and right of the Sun and producing a composite image by stitching together the off-pointed and the Sun-centered images. The imaging area in the composite is about three times the nominal image area in the East-West direction (about 5 RSun versus 1.8 RSun for nominal images). The campaign was conducted in February (4 hours), June (72 hours), and August-September of 2018 (5 weeks). Results from the campaign indicated the presence of solar corona to three solar radii, even in the quiet Sun part of the solar cycle. NOAA can operationalize this concept by tasking the SUVI on one of GOES-E and GOES-W. Such long-term operation will provide data that is needed to establish the much needed connectivity between the EUV and white light coronagraph data for the CME events.

Extended Coronal↗
NASA NTRS1992

Test and analysis results for composite transport fuselage and wing structures

Automated tow placement (ATP) and stitching of dry textile composite preforms followed by resin transfer molding (RTM) are being investigated by researchers at NASA LaRC and Douglas Aircraft Company as cost-effective manufacturing processes for obtaining damage tolerant fuselage and wing structures for transport aircraft. The Douglas work is being performed under a NASA contract entitled 'Innovative Composites Aircraft Primary Structures (ICAPS)'. Data are presented in this paper to assess the damage tolerance of ATP and RTM fuselage elements with stitched-on stiffeners from compression tests of impacted three-J-stiffened panels and from stiffener pull-off tests. Data are also presented to assess the damage tolerance of RTM wing elements which had stitched skin and stiffeners from impacted single stiffener and three blade-stiffened compression tests and stiffener pull-off tests.

Deaton, Jerry W.↗
NASA NTRS1992

Test and analysis results for composite transport fuselage and wing structures

Automated tow placement (ATP) and stitching of dry textile composite preforms followed by resin transfer molding (RTM) are being studied as cost effective manufacturing processes for obtaining damage tolerant fuselage and wing structures for transport aircraft. Data are presented to assess the damage tolerance of ATP and RTM fuselage elements with stitched-on stiffeners from compression tests of impacted three J-stiffened panels and from stiffener pull-off tests. Data are also presented to assess the damage tolerance of RTM wing elements which had stitched skin and stiffeners from impacted single stiffener and three blade stiffened compression tests and stiffener pull-off tests.

Deaton, Jerry W.↗
NASA NTRS2012

Vibroacoustic Characterization of a New Hybrid Wing-Body Fuselage Concept

A lighter, more robust airframe design is required to withstand the loading inherent to next generation non cylindrical commercial airliners. The Pultruded Rod Stitched Efficient Unitized Structure concept, a highly integrated composite design involving a stitched and co-cured substructure, has been developed to meet such requirements. While this structure has been shown to meet the demanding out-of-plane loading requirements of the flat-sided pressurized cabin design, there are concerns that the stiff co-cured details will result in relatively high acoustic radiation efficiencies at frequencies well below the thin skin acoustic coincidence frequency. To address this concern and establish a set of baseline vibroacoustic characteristics, a representative test panel was fabricated and a suite of tests were conducted that involved measurements of panel vibration and radiated sound power during point force and diffuse acoustic field excitations. Experimental results are shown and compared with Finite Element and Statistical Energy Analysis model predictions through the use of modal and energy correlation techniques among others. The behavior of the structure subject to turbulent boundary layer excitation is also numerically examined.

Allen, Albert R.↗
NASA NTRS1999

Probabilistic Assessment of Fracture Progression in Composite Structures

This report describes methods and corresponding computer codes that are used to evaluate progressive damage and fracture and to perform probabilistic assessment in built-up composite structures. Structural response is assessed probabilistically, during progressive fracture. The effects of design variable uncertainties on structural fracture progression are quantified. The fast probability integrator (FPI) is used to assess the response scatter in the composite structure at damage initiation. The sensitivity of the damage response to design variables is computed. The methods are general purpose and are applicable to stitched and unstitched composites in all types of structures and fracture processes starting from damage initiation to unstable propagation and to global structure collapse. The methods are demonstrated for a polymer matrix composite stiffened panel subjected to pressure. The results indicated that composite constituent properties, fabrication parameters, and respective uncertainties have a significant effect on structural durability and reliability. Design implications with regard to damage progression, damage tolerance, and reliability of composite structures are examined.

Chamis, Christos C.↗
NASA NTRS2019

Impact Damage Tolerance of Composite Laminates with Through-The-Thickness Stitches

The ability of through-the-thickness stitches to contain damage during a low-velocity impact event and increase the residual strength of stitched panels was investigated in this research. The impact response, spread of interlaminar delaminations, dent depth, surface damage, and static residual strength after impact were studied for carbon-epoxy specimens fabricated from HTS40 TohoTenax standard modulus fibers, stitched together with Vectran 1200 denier thread and infused with API 1078 resin after through-the-thickness stitching. Three different stitch patterns were used to explore the ability to arrest impact damage during and after impact. Simply supported boundary conditions were maintained during the impact testing. Non-destructive evaluations were performed using ultrasonic C-scans and X-ray computed tomography (CT) imaging to determine the shape, size, and location of delaminations. Results indicate that while the dynamic response during the impact event was almost the same for the unstitched specimens and all stitch patterns considered, the extent of delamination and the compression strength after impact varied greatly. For both the 60 J and 80 J impact energies, the delamination area was significantly less for the stitched specimens than for the unstitched specimens, but the range of delamination areas among the stitch patterns was much larger for the lower impact energy than for the greater impact energy. Similarly, while the presence of stitching influenced the compression after impact strength, the strength values for all stitch patterns were very similar. These results are a step toward quantifying the influence of through-the-thickness stitching.

Ranatunga, Vipul↗
NASA NTRS1995

Impact testing of textile composite materials

The objectives of this report were to evaluate the impact damage resistance and damage tolerance of a variety of textile composite materials. Static indentation and impact tests were performed on the stitched and unstitched uniweave composites constructed from AS4/3501-6 Carbon/Epoxy with a fiberglass yarn woven in to hold the fibers together while being stitched. Compression and tension were measured after the tests to determine the damage resistance, residual strength and the damage tolerance of the specimens.

Portanova, Marc↗
NASA NTRSDate not supplied

On the Representation of Through-The-Thickness Reinforcements in Finite Element Analysis of Stitched, Blade Stiffened Panels

Modern aircraft employ laminated composites for their tailorable in-plane properties, high specific strengths, and high specific stiffnesses. However, laminated composites exhibit relatively poor interlaminar properties without through-the-thickness reinforcements. Quantifying the necessary amount of through-the-thickness reinforcements is necessary to reduce cost and meet damage tolerance certification requirements. In this study, a discrete superposed cohesive element (DSCE) approach is applied to represent the mixed-mode delamination behavior of stitched stiffened panels subjected to seven-point bending. This approach is compared to a one-dimensional embedded spring element (ESE) method. The DSCE approach uses two superposed bilinear traction-separation laws to obtain a representative load-displacement response determined from interlaminar tensile and shear tests. Additionally, several stitch configurations (unstitched, stitched, and overstitched) are evaluated in terms of their load-displacement response and crack-arrestment capability. Results indicate that the DSCE and ESE approaches show good agreement with respect to the predicted load-displacement response, but the ESE method tends to overpredict the crack growth behavior by approximately 13%. Stitches were not observed to fail during skin-stringer separation. Using an overstitched laminate with stitches near the flange edge provides the greatest crack-arrestment capability. Furthermore, the skin retains 92% of its stiffness after skin-stringer separation occurs.

composites↗
NASA NTRSDate not supplied

On the Representation of Through-The-Thickness Reinforcements in Finite Element Analysis of Stitched, Blade Stiffened Panels

Modern aircraft employ laminated composites for their tailorable in-plane properties, high specific strengths, and high specific stiffnesses. However, laminated composites exhibit relatively poor interlaminar properties without through-the-thickness reinforcements. Quantifying the necessary amount of through-the-thickness reinforcements is necessary to reduce cost and meet damage tolerance certification requirements. In this study, a discrete superposed cohesive element (DSCE) approach is applied to represent the mixed-mode delamination behavior of stitched stiffened panels subjected to seven-point bending. This approach is compared to a one-dimensional embedded spring element (ESE) method. The DSCE approach uses two superposed bilinear traction-separation laws to obtain a representative load-displacement response determined from interlaminar tensile and shear tests. Additionally, several stitch configurations (unstitched, stitched, and overstitched) are evaluated in terms of their load-displacement response and crack-arrestment capability. Results indicate that the DSCE and ESE approaches show good agreement with respect to the predicted load-displacement response, but the ESE method tends to overpredict the crack growth behavior by approximately 13%. Stitches were not observed to fail during skin-stringer separation. Using an overstitched laminate with stitches near the flange edge provides the greatest crack-arrestment capability. Furthermore, the skin retains 92% of its stiffness after skin-stringer separation occurs.

composites↗
NASA NTRS2014

Evaluation of RTM370 Polyimide Composites by Resin Film Infusion (RFI)

RTM370 imide oligomer based on 2,3,3',4'-biphenyl dianhydride (a-BPDA), 3,4'-oxydianiline (3,4'-ODA) and terminated with the 4-phenylethynylphthalic (PEPA) endcap has been shown to exhibit a low melt viscosity (10-30 poise) at 280 C with a pot-life of 1-2 h and a high cured glass-transition temperature (Tg) of 370 C. RTM370 resin has been successfully infused into fiberglass-stitched T650-35 carbon-fabric preforms (ranged from 3- to 6-mm thick) by resin film infusion (RFI). The resulting composite panels were inspected by ultrasonic C-scan and by photomicrographs before and after post-curing as a quality control. Mechanical tests such as unnotched compression (UNC), open-hole compression (OHC), and short-beam shear strength (SBS) at ambient and elevated temperatures were performed before and after isothermal aging at 288 C for 1000 h to assess high-temperature performance. Thermal cycling of RTM370 stitched composites was also conducted from -54 C to 288 C for up to 1600 cycles to evaluate the microcrack resistance of RTM370 polyimide composites fabricated by RFI.

Polyimide↗
NASA NTRS1993

Mechanical characterization of 2D, 2D stitched, and 3D braided/RTM materials

Braided composite materials have potential for application in aircraft structures. Fuselage frames, floor beams, wing spars, and stiffeners are examples where braided composites could find application if cost effective processing and damage tolerance requirements are met. Another important consideration for braided composites relates to their mechanical properties and how they compare to the properties of composites produced by other textile composite processes being proposed for these applications. Unfortunately, mechanical property data for braided composites do not appear extensively in the literature. Data are presented in this paper on the mechanical characterization of 2D triaxial braid, 2D triaxial braid plus stitching, and 3D (through-the-thickness) braid composite materials. The braided preforms all had the same graphite tow size and the same nominal braid architectures, (+/- 30 deg/0 deg), and were resin transfer molded (RTM) using the same mold for each of two different resin systems. Static data are presented for notched and unnotched tension, notched and unnotched compression, and compression after impact strengths at room temperature. In addition, some static results, after environmental conditioning, are included. Baseline tension and compression fatigue results are also presented, but only for the 3D braided composite material with one of the resin systems.

Deaton, Jerry W.↗