Search NASA⌕ Search

SEARCH · Search NASA

Results for “stress voiding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks

Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.

42 ENGINEERING↗
DOE OSTI2023

An examination of the precipitation behavior of proton irradiated dual phase 308L weldment filler materials

Voids, G phase particles, and Ni-Si rich clusters in proton irradiated dual phase 308L groove filler of a SA508–304 L dissimilar metal weldment are analyzed using advanced characterization techniques. These weldments are often used in light water nuclear reactors and are subject to enhanced corrosion and associated stress corrosion cracking (SCC). Radiation damage is known to accelerate SCC. Ni-Si enriched clusters were observed in proton irradiated γ austenite, while G phase M 6 Ni 16 Si 7 (where M transition metal element) precipitates were observed in proton irradiated δ ferrite. Compositional analysis of the G phase precipitates and Ni-Si clusters from STEM-EDS and APT are compared. Unlike G phase particles in proton irradiated δ ferrite, Ni-Si clusters in proton irradiated γ austenite are not rich in Mn. Both STEM-EDS and APT line-scan profiles of the Ni-Si clusters show that the Fe and Cr concentration gradient between matrix γ austenite and the Ni-Si clusters is not as sharp as those between matrix δ ferrite and G phase. Further, HR-STEM imaging indicates that the lattice parameter of the Ni-Si clusters is commensurate with γ austenite and the clusters do not represent the precipitation of a second phase. Finally, our analysis demonstrates the density and volume fraction of G phase particles and the density of voids scales with proton irradiation damage and the energy to recoils.

308L groove filler↗
DOE OSTI2020

Microstructural characterization of cold-worked 316 stainless steel flux thimble tubes irradiated up to 100 dpa in a commercial Pressurized Water Reactor

Two flux thimble tubes (FTT) made of 15% cold-worked 316 stainless steel (SS) were harvested from Ringhals Pressurized Water Reactor (PWR) Unit 2, with peak damages of 76 and 100 displacements per atom (dpa) after 29 and 34 years’ service, respectively. Specimens sectioned from parent tubes were comprehensively characterized with nominal damage levels of ~0, ~41, ~74, 76, and 100 dpa at a nominal temperature range of 285-323 °C. Both FTTs contained helium and hydrogen gases as transmutation products. The helium follows a production rate of ~9.8 appm/dpa, while environmental factors complicate hydrogen production obscuring an exact H/dpa ratio. Irradiation-induced dislocation loops, nano-cavities, solute clusters, and microsegregation were all observed. The dislocation loops and nano-cavities indicated saturation at 41 dpa. The solute clusters continued to evolve with Ni-Si clusters formed at 41 dpa, and Ni-Si-Mn-P clusters formed at 74 and 100 dpa, but neither clusters exhibited distinct diffraction patterns at any damage levels. Solute clusters were observed to frequently be co-located with dislocation loops, but fully decorated loops were rarely detected. Significant radiation-induced segregation (RIS) was observed around grain boundaries at all damage levels. The modified inverse Kirkendall (MIK) model captured the RIS behavior of major elements. Large cavities within or around an Mn-S rich region were observed for the first time. Through all the damage levels, void swelling is always below 0.05%, making significant dimensional change unlikely in core internals when used at similar conditions. Meanwhile, the role of overwhelming nanocavities, presumably helium bubbles, should be considered in other potential degradation mechanisms, including irradiation-assisted stress corrosion cracking, embrittlement, and loss of fracture toughness, which remain the concerns for extended operation of nuclear power plants.

Post Irradiation Examination, Isotope Dilution Mas↗
DOE OSTI2023

Predicting Failure Using Deep Learning SAND Report

Accurate prediction of ductile failure is critical to Sandia’s NW mission, but the models are computationally heavy. The costs of including high-fidelity physics and mechanics that are germane to the failure mechanisms are often too burdensome for analysts either because of the person-hours it requires to input them or because of the additional computational time, or both. In an effort to deliver analysts a tool for representing these phenomena with minimal impact to their existing workflow, our project sought to develop modern data-driven methods that would add microstructural information to business-as-usual calculations and expedite failure predictions. The goal is a tool that receives as input a structural model with stress and strain fields, as well as a machine-learned model, and output predictions of structural response in time, including failure. As such, our project spent substantial time performing high-fidelity, three-dimensional experiments to elucidate materials mechanisms of void nucleation and evolution. We developed crystal-plasticity finite-element models from the experimental observations to enrich the findings with fields not readily measured. We developed engineering length-scale simulations of replicated test specimens to understand how the engineering fields evolve in the presence of fine-scale defects. Finally, we developed deep learning convolutional neural networks, and graph-based neural networks to encode the findings of the experiments and simulations and make forward predictions in time for structural performance. This project demonstrated the power of data-driven methods for model development, which have the potential to vastly increase both the accuracy and speed of failure predictions. These benefits and the methods necessary to develop them are highlighted in this report. However, many challenges remain to implementing these in real applications, and these are discussed along with potential methods for overcoming them.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Mechanics of vitrimer particle compression and fusion under heat press

The compression and fusion of vitrimer particles is a fundamental problem underlying the recycling of vitrimers. Incomplete particle compression can lead to voids in the fused vitrimer, thereby impacting its mechanical property. In this work, we present a two-dimensional finite element model to capture the interplay of multiple complex mechanisms including random particle packing, large deformation, inter-particle contact, thermally activated bulk stress relaxation, and interface healing. Specifically, we focus on understanding two key components of this problem: i) evolution of porosity during compression and fusion of randomly packed vitrimer particles, and ii) effective tensile modulus and strength of fused vitrimer. Using the finite element model, we first show that using smaller particles can reduce the porosity in the fused vitrimer, which only slightly increases the effective modulus, but the increase in tensile strength is more pronounced. In addition, under the same processing conditions, particles with mixed sizes can achieve better densification and higher tensile strength after fusion than uniformly sized particles with the same average radius. Regarding the effects of processing conditions, we discuss how the porosity and effective modulus of the fused vitrimer depend on the processing time, temperature and pressure, and find a general trend consistent with experimental observations, i.e. longer processing time, higher temperature or higher pressure can lead to lower porosity and higher modulus of the fused vitrimer. Finally, the theoretical insights towards the compression and fusion process as well as the simulation framework can be useful in optimizing the powder-based heat press process of vitrimer and its composites.

42 ENGINEERING↗
DOE OSTI2023

Influence of Potassium Metal‐Support Interactions on Dendrite Growth

Abstract Combined synchrotron X‐ray nanotomography imaging, cryogenic electron microscopy (cryo‐EM) and modeling elucidate how potassium (K) metal‐support energetics influence electrodeposit microstructure. Three model supports are employed: O‐functionalized carbon cloth (potassiophilic, fully‐wetted), non‐functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo‐FIB) cross‐sections yield complementary three‐dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub‐10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore‐free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate‐metal interaction on K metal film nucleation and growth, as well as the associated stress state.

Liu, Pengcheng↗
DOE OSTI2020

Shockwave dissipation by interface-dominated porous structures

The advent of additive manufacturing (AM) has enabled topological control of structures at the micrometer scale, transforming the properties of polymers for a variety of applications. Examples include tailored mechanical responses, acoustic properties, and thermal properties. Porous polymer materials are a class of materials used for shock and blast mitigation, yet they frequently possess a lack of structural order and are largely developed and evaluated via trial-and-error. Here, we demonstrate control of shockwave dissipation through interface-dominated structures prepared by AM using 2-photon polymerization. A fractal structure with voids, or free surfaces, arranged less than 100 μm apart, allows for rarefaction interactions on the timescale of the shockwave loading. Simulations and dynamic x-ray phase contrast imaging experiments show that fractal structures with interfaces assembled within a “critical” volume reduce shockwave stress and wave velocity by over an order of magnitude within the first unit cell.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mechanically graded granular scaffolds for osteochondral tissue engineering

Engineered scaffolds designed to approximate the mechanical microenvironment of the osteochondral unit often address this complexity using discrete, two-phase architectures that introduce mechanical discontinuities and interfacial stress concentrations rather than a contiguous stiffness transition. To address this challenge, we created a photoannealed polyethylene glycol (PEG) granular scaffold with a spatially controlled stiffness gradient within a cell-permissive, macroporous architecture. Stiffness was dictated by photoannealing microgels using a photomask. We tuned void volume and available surface area by varying microgel diameter and tested how mesenchymal stromal cells (MSCs) interpret local mechanical environments. MSCs exhibited position-dependent differences in morphology, cytoskeletal structure, matrix deposition, and lineage-specific gene expression within the gradient scaffolds. Softer regions supported rounded cell morphology and deposition of a glycosaminoglycan-rich matrix, whereas stiffer regions promoted cell elongation, increased cytoskeletal tension, and expression of mineral-associated markers. Gradients formed from smaller microgels magnified these spatial responses by increasing cellular confinement and adhesion site availability. Disruption of actomyosin contractility eliminated these regional differences, demonstrating that MSCs rely on tension-dependent mechanotransduction to interpret the gradient. These findings reveal that coupling microgel architecture with continuous stiffness transitions provides a tractable platform to study multiscale mechanobiologic regulation and spatially guide osteochondral tissue formation.

Biological and medical sciences↗
DOE OSTI2023

Influence of Potassium Metal-Support Interactions on Dendrite Growth

We report combined synchrotron X-ray nanotomography imaging, cryogenic electron microscopy (cryo-EM) and modeling elucidate how potassium (K) metal-support energetics influence electrodeposit microstructure. Three model supports are employed: O-functionalized carbon cloth (potassiophilic, fully-wetted), non-functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo-FIB) cross-sections yield complementary three-dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub-10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore-free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate-metal interaction on K metal film nucleation and growth, as well as the associated stress state.

36 MATERIALS SCIENCE↗
DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗
DOE OSTI2021

1000 Wh L−1 lithium-ion batteries enabled by crosslink-shrunk tough carbon encapsulated silicon microparticle anodes

Abstract Microparticulate silicon (Si), normally shelled with carbons, features higher tap density and less interfacial side reactions compared to its nanosized counterpart, showing great potential to be applied as high-energy lithium-ion battery anodes. However, localized high stress generated during fabrication and particularly, under operating, could induce cracking of carbon shells and release pulverized nanoparticles, significantly deteriorating its electrochemical performance. Here we design a strong yet ductile carbon cage from an easily processing capillary shrinkage of graphene hydrogel followed by precise tailoring of inner voids. Such a structure, analog to the stable structure of plant cells, presents ‘imperfection-tolerance’ to volume variation of irregular Si microparticles, maintaining the electrode integrity over 1000 cycles with Coulombic efficiency over 99.5%. This design enables the use of a dense and thick (3 mAh cm–2) microparticulate Si anode with an ultra-high volumetric energy density of 1048 Wh L–1 achieved at pouch full-cell level coupled with a LiNi0.8Co0.1Mn0.1O2 cathode.

25 ENERGY STORAGE↗
DOE OSTI2022

Atomistic modeling of tensile deformation and fracture of carbon fibers: Nanoscale stress redistribution, effect of local structural characteristics and nanovoids

The mechanisms of tensile deformation and fracture of carbon fibers are investigated in large-scale molecular dynamics simulations. The simulations performed for computational samples with different structural characteristics enable analysis of the structural sensitivity of the mechanical properties. It is found that the carbon fiber nanostructure can be represented by a fine (nanoscale) mixture of stiff and soft regions. Despite the nanoscale structural heterogeneity of the computational fibers, their fracture strain and tensile strength exceed the experimental values by almost an order of magnitude. Here, this observation is explained by the ability of the carbon fiber nanostructure, largely consisting of curved and folded layers of turbostratic carbon, to exhibit continuous nanoscale load redistribution during the deformation. The transient, fluid nature of a percolating cluster of stress-holding structural elements prevents stress localization at the early stage of the deformation and enables the fiber nanostructure to adapt to the increasing load. Overall, the results of the simulations suggest that the design of advanced carbon fiber manufacturing and post-processing methods focused on the elimination of critical mesoscopic structural defects (internal voids, foreign inclusions, and surface flaws) can yield a substantial increase in the strength and fracture strain of carbon fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Grain-boundary fracture mechanisms in Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolytes: When phase transformation acts as a temperature-dependent toughening mechanism

Garnet-type, solid electrolytes, such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising alternative to liquid electrolytes for lithium-metal batteries. However, such solid-electrolyte materials frequently exhibit undesirable lithium (Li) metal plating and fracture along grain boundaries. In this work, we employ atomistic simulations to investigate the mechanisms and key fracture properties associated with intergranular fracture along one such boundary. Our results show that, in the case of a Σ5 (310) grain boundary, this boundary exhibits brittle fracture behavior, i.e. the absence of dislocation activity ahead of the propagating crack tip, accompanied with a decrease in work of separation, peak stress, and maximum stress intensity factor as the temperature increases from 300 K to 1500 K. As the crack propagates, we predict two temperature-dependent Li clustering regimes. For temperatures at or below 900 K, Li tends to cluster in the bulk region away from the crack plane driven by a void-coalescence mechanism concomitant a simultaneous cubic-to-tetragonal phase transition. The tetragonalization of LLZO in this temperature regime acts as an emerging toughening mechanism. At higher temperatures, this phase transition mechanism is suppressed leading to a more uniform distribution of Li throughout the grain-boundary system and lower fracture properties as compared to lower temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of Re and Al additions on the microstructure and mechanical properties of Nb-18Ti-12W alloy

Microstructure and mechanical properties at 25–1200 °C of new refractory alloys, Nb-18Ti-12W (NTW), Nb-18Ti-12W-5Re (NTW-R) and Nb-18Ti-12W-5Re-1Al (NTW-RA), all compositions are in atomic percent, are reported. The alloys are developed as an alternative to a denser, more expensive and difficult-to-process refractory alloy WC-3009. After production by arc melting and hot isostatic pressing at 1400 °C, 207 MPa for 3 h, the alloys have a BCC crystal structure with the average grain size of ~150–200 μm and contain low volume fraction of (Ti,N)-rich precipitates near grain boundaries. NTW shows excellent malleability at all studied temperatures. Its yield stress at 25 °C, 1000 °C and 1200 °C is 874 MPa, 353 MPa and 202 MPa, respectively. The NTW-R and NTW-RA alloys are stronger at all the studied temperatures; however, they lack in compression ductility at 25 °C. As a result, extensive deformation twinning and formation of intergranular voids precede the fracture of these two alloys at 25 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Micro-tensile characteristics of As-fabricated and irradiated AGR-2 TRISO fuel particle buffer, IPyC, and buffer-IPyC interlayer regions

A recently developed micro-tensile sample preparation technique was implemented to evaluate the tensile strengths of the buffer, IPyC, and buffer-IPyC interlayer regions of the unirradiated and irradiated AGR-2 TRISO fuel particles. Understanding the mechanical properties of the buffer-IPyC interlayer is essential for developing thermomechanical models of buffer-IPyC separation, yet there is a lack of experimental data on its micro-tensile properties. TEM analysis was conducted on these regions to determine the microstructural changes relevant to the samples' tensile properties. In the unirradiated TRISO particle samples, the buffer layer demonstrated the weakest tensile strength, while the IPyC layer exhibited the highest. Conversely, in the irradiated TRISO particle samples, the buffer-IPyC interlayer region showed the lowest tensile strength, with the IPyC layer being the strongest. Fractures in the samples from the buffer-IPyC region predominantly occurred either in the buffer layer or at the buffer-IPyC interface. However, some buffer-IPyC interlayer samples displayed stress-strain and fracture behaviors more akin to the IPyC layer than the buffer layer. Analysis of diffraction patterns suggests that irradiation may have increased anisotropy in the three regions tested. Despite this suggested increase in anisotropy, there was no evidence that it affected the measured strengths. The irradiated TRISO particles demonstrated a considerable increase in void space and a decrease in ultimate tensile strength within the buffer-IPyC interlayer region due to the densification and contraction of the buffer layer. Minor variations in diffraction ring patterns were also observed. These changes, coupled with a significant reduction in the Weibull modulus/shape parameter, imply that irradiation-induced densification leads to tearing between the buffer and IPyC layers at locations of elevated porosity in the buffer-IPyC interlayer region.

Tristructural isotropic (TRISO)↗
DOE OSTI2022

Effect of grain size on damage and failure in two-phase materials: Homogenized CuPb

It is well known that spall failure strongly depends on the microstructure of a material. There have been numerous studies to study the effect of grain size on the overall spall strength and the total amount of damage in single element metals like copper. However, such systematic studies remain rare in two-phase materials and alloys. In this work, two incipient spall experiments were performed on a Cu–1%Pb alloy to understand the effect of grain size on the damage and failure in a two-phase material. Overall, these results showed that even though the spall strength did not change as a function of grain size, there were significant differences in the total amount of damage as a function of grain size. A clear increase in the total damage present in the material was seen as the grain size was increased from 32 to either 70 or 75 μm in either of the experiments. Furthermore, this difference was attributed to variations in the void growth rate as the grain size was increased.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing Microstructure-induced Swelling & Thermal Property Changes in Ion-Irradiated Oxide Fuels using Laser-generated Surface Acoustic Waves

Radiation of fuel rods with neutrons during a fission reaction in a nuclear reactor is known to affect the material microstructure of the fuel as a result of fission fragment damage, and lead to the formation of atomic-level defects such as voids, dislocation loops, and lattice swelling from fission-gas release. A consequence of the radiation-induced damage in nuclear fuels is the drastic alteration of material properties, in particular, the reduction of the thermal conductivity – a key parameter that governs the transport of thermal energy released from fissile fuel atoms to the surrounding coolant. Swelling can induce high stresses and ultimate failure of the cladding. A fundamental understanding of the role of radiation-induced damage on the thermal transport and mechanical properties of nuclear fuels is therefore critical for efficient, reliable and safe operation of a nuclear power plant. As opposed to conventional post-irradiation examination techniques that are often time-consuming and require significant sample preparation, laser-based characterization methods have emerged as promising non-contact, non-destructive tools to measure the evolution of microstructure-induced material property changes. Moreover, laser methods offer the promise of in-situ characterization while the material is being irradiated. This project aims to develop an improved understanding of the impact of radiation-induced changes to material microstructure on the thermal and elastic properties of nuclear materials. A laser ultrasonic technique, known as the transient grating (TG) spectroscopy method, is used to simultaneously measure thermal diffusivity and elastic properties in unirradiated and ion-irradiated oxide nuclear fuel samples. The results will complement on-going investigations on electron- and phonon-mediated thermal transport in nuclear materials and will provide foundational work for incorporating the influence of defects in fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗