Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface alloying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Effect of Cooling Rate on Nano-Eutectic Formation in Laser Surface Remelted and Rare Earth Modified Hypereutectic Al-20Si Alloys

Laser Surface Remelting (LSR) was applied to arc-melted Al-20Si-0.2Sr, Al-20Si-0.2Ce, and Al-20Si hypereutectic alloys to refine microstructures. Experiments revealed that microstructures in the melt pool varied from fully eutectic to a mixture of Al dendrites and inter-dendritic eutectic. We calculated cooling rates using the Eagar-Tsai model and correlated cooling rates with characteristic microstructures, revealing that a cooling rate on the order of 104 K/s could lead to maximized fully eutectic microstructure morphology. Due to rapid solidification, the Si composition in the LSR eutectic was measured at 18.2 wt.%, higher than the equilibrium eutectic composition of 12.6 wt.%Si. Compared to Al-20Si, Ce addition had no significant effect on the volume fraction of the fully eutectic structure but refined Si fibers to approximately 30 nm in diameter. Sr addition did not further refine the diameter of eutectic Si fibers compared to Al-20Si but increased the volume fraction of the fully eutectic microstructure morphology. The refinement ratio (φ) of the Si fiber diameter from the bottom of the melt pool to the surface for the three alloys was similar, at around 28%. The established correlation between the cooling rate and the size and morphology of the microstructure within the melt pool will enable tailoring of the microstructure in laser-processed as well as deposited alloys for high strength and plasticity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atmospheric Pressure Plasma Treatment of Magnesium Alloy for Enhanced Coating Adhesion and Corrosion Resistance

Atmospheric pressure plasma (AP) treatment, using an open-air jet of ionized CO 2 , N 2 , or air, was applied to AZ91D Mg alloy surfaces to investigate its effects on primer coating adhesion and corrosion resistance. The CO 2 and air AP treatments formed an O- and C-rich surface layer (Mg-O-C) consisting of agglomerated nanoparticles and pits with a depth of a few microns and increasing the surface roughness by 6–8 times compared with the reference 600 grit-finished surface. Then, three commercial primers, zinc phosphate (ZnP), chromate-containing epoxy, and MIL23377, were applied on the treated surfaces to evaluate the corrosion resistance associated with the coating adhesion. Microscopic analysis demonstrated stronger interlocking between the primer layer and the nano-/microrough Mg-O-C surface compared to the untreated (600 grit-finished) surfaces, indicating improved coating adhesion and corrosion resistance. Crosscut tests of the MIL23377 primer on the CO 2 and air AP-treated surfaces showed the highest level of adhesion, ASTM class 5B. Salt spray corrosion tests showed that after 8 days of exposure, the primer coatings on air AP-treated surfaces had corrosion areas that were more than four times smaller than that of the 600 grit-finished surface. The N 2 AP treatment showed similar adhesion enhancement. The preliminary operation expenses for AP treatment using CO 2 , N 2 , and air were estimated at USD 30.62, USD 35.45, and USD 29.75 (from an air cylinder)/USD 0.66 (from an air compressor) per m 2 , respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Distinguishing Elements at the Sub‐Nanometer Scale on the Surface of a High Entropy Alloy

Materials in crystalline form possess translational symmetry (TS) when the unit cell is repeated in real space with long- and short-range orders. The periodic potential in the crystal regulates the electron wave function and results in unique band structures, which further define the physical properties of the materials. Amorphous materials lack TS due to the randomization of distances and arrangements between atoms, causing the electron wave function to lack a well-defined momentum. High entropy materials provide another way to break the TS by randomizing the potential strength at periodic atomic sites. The local elemental distribution has a great impact on physical properties in high entropy materials. It is critical to distinguish elements at the sub-nanometer scale to uncover the correlations between the elemental distribution and the material properties. Here, the use of synchrotron X-ray scanning tunneling microscopy (SX-STM) with sub-nm scale resolution in identifying elements on a high entropy alloy (HEA) surface is demonstrated. By examining the elementally sensitive X-ray absorption spectra with an STM tip to enhance the spatial resolution, the elemental distribution on an HEA's surface at a sub-nm scale is extracted. In conclusion, these results open a pathway towards quantitatively understanding high entropy materials and their material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Engineering Active Sites of Metal/Metal Oxide Catalysts by Oxide Ligand Overlayers

Abstract Engineering sites of supported metal catalysts is essential to enhancing activity and selectivity. Such enhancement is typically achieved by particle size modification, surface alloying, or attaching molecular ligands. Yet, control strategies for complex, multifunctional molecules and catalysts, where selectivity is crucial, are lacking. Here, we demonstrate that submonolayer WO x with tunable coverage preferentially decorates well‐coordinated Pt terrace sites as a stable ligand. By combining experimental kinetics with probe molecules, in situ spectroscopies, and first‐principles modeling, we show that the WO x coverage on Pt modifies the metal‐to‐acid site balance while retaining the acid strength intact and results in optimal reactivity for metal‐acid catalyzed reactions at a specific metal, size, and support‐dependent WO x coverage. The oxide can also alter the reactant adsorption mode, reversing selectivity and pathways from terrace‐ to step‐dominated, as evidenced in furfural decarbonylation and hydrogenation. The insights open avenues for improving metal/metal oxide catalysts beyond the specific system.

Zhou, Jiahua↗
DOE OSTI2020

Au x Pd (300‐ x ) Alloy Nanoparticles for the Oxygen Reduction Reaction in Alkaline Media

Abstract Au x Pd (300‐ x ) nanoalloys were prepared using a dendrimer‐templating method and their electrocatalytic efficiencies towards the oxygen reduction reaction (ORR) were analyzed in alkaline media. The composition‐dependent PdO x reduction potentials of the Au x Pd (300‐ x ) nanoalloys were correlated to the oxygen‐binding (O‐binding) energy of the catalysts. Multiple PdO x reduction peaks were present for the Au 150 Pd 150 and Au 50 Pd 250 catalysts. These peaks were assigned to the alloyed and bulk‐like Pd active sites on the alloyed surface. The results described here are significant because modulation of the O‐binding energies improved the ORR activity on the nanoalloys. Specifically, a linear trend in O‐binding energies of Au x Pd (300‐ x ) dendrimers (DENs) as a function of Pd composition resulted in a volcano‐shaped trend in ORR activity. The optimal O‐binding energy of Au 50 Pd 250 resulted in an approximate 89 mV shift in PdO x reduction relative to Pd 300 and a shift of approximately 76 mV in ORR peak potential.

Trindell, Jamie A.↗
DOE OSTI2024

A data-driven multiscale model for reactive wetting simulations

Here, we describe a data-driven, multiscale technique to model reactive wetting of a silver–aluminum alloy on a Kovar™ (Fe-Ni-Co alloy) surface. We employ molecular dynamics simulations to elucidate the dependence of surface tension and wetting angle on the drop’s composition and temperature. A design of computational experiments is used to efficiently generate training data of surface tension and wetting angle from a limited number of molecular dynamics simulations. The simulation results are used to parameterize models of the material’s wetting properties and compute the uncertainty in the models due to limited data. The data-driven models are incorporated into an engineering-scale (continuum) model of a silver–aluminum sessile drop on a Kovar™ substrate. Model predictions of the wetting angle are compared with experiments of pure silver spreading on Kovar™ to quantify the model-form errors introduced by the limited training data versus the simplifications inherent in the molecular dynamics simulations. The paper presents innovations in the determination of “convergence” of noisy MD simulations before they are used to extract the wetting angle and surface tension, and the construction of their models which approximate physio-chemical processes that are left unresolved by the engineering-scale model. Together, these constitute a multiscale approach that integrates molecular-scale information into continuum scale models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Effect of excess Mg to control corrosion in molten MgCl 2 and KCl eutectic salt mixture

Structural alloys may experience corrosion when exposed to molten chloride salts due to selective dissolution of active alloying elements. One way to prevent this is to make the molten salt reducing. For the KCl + MgCl 2 eutectic salt mixture, pure Mg can be added to achieve this. However, Mg can form intermetallic compounds with nickel at high temperatures, which may cause alloy embrittlement. This work shows that an optimum level of excess Mg could be added to the molten salt which will prevent corrosion of alloys like 316 H, while not forming any detectable Ni-Mg intermetallic phases on Ni-rich alloy surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

H 2 O-assisted O 2 reduction by H 2 on Pt and PtAu bimetallic nanoparticles: Influences of composition and reactant coverages on kinetic regimes, rates, and selectivities

Hydrogen peroxide (H 2 O 2 ) can replace hazardous oxidants in industrial processes but is currently too expensive for many such applications. While direct synthesis of H 2 O 2 (H 2 + O 2 → H 2 O 2 ) may reduce costs in comparison to incumbent technology, current catalysts lack the requisite stability and selectivity. Here, we examine the direct synthesis of H 2 O 2 on bimetallic Pt 1 Au x (0 ≤ x ≤ 230) and Pt catalysts at steady-state in pure water and relate kinetic parameters for H 2 O 2 and H 2 O formation to possible active site structures informed by complementary characterization methods. X-ray photoelectron spectra show significant Pt surface enrichment compared to the bulk composition. Analysis of infrared spectra of mixed monolayers of 12 CO* and 13 CO* indicate that Pt and Au form substitutional surface alloys. The Pt 1 Au x nanoparticles with the greatest mole fractions of Au predominantly expose Pt monomers (i.e., isolated Pt atoms), yet Pt atoms exposed upon all these nanoparticles possess electronic structures distinct from bulk Pt. Despite these differences, rate measurements are consistent with product formation through proton-electron transfer pathways for all Pt 1 Au x catalysts. In situ XAS indicate that Pt remains metallic during H 2 O 2 synthesis. Under the most oxidizing conditions, selectivities toward H 2 O 2 increase strongly with the Au to Pt ratio from 2% for monometallic Pt to 85% for Pt 1 Au 170 . However, selectivities are similar among all catalysts within reducing conditions. Comparisons of apparent activation enthalpies for the formation of H 2 O 2 and H 2 O across these catalysts and the range of conditions suggest that Pt monomers within Au provide the greatest selectivities for H 2 O 2 formation, because these active sites present high barriers for O-O bond rupture. Further, selectivities decrease with increasing ratios of H 2 to O 2 pressures, because Pt atoms aggregate and form oligomers that readily dissociate dioxygen intermediates. The combined use of spectroscopy, kinetics, and concepts employed in reaching these conclusions take inspiration from the legacy of Prof. Michel Boudart, and specifically his elegant methods for interrogating bimetallic catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Carburization of metals by a chemical mechanism of carbon transport through molten fluoride salts

Carburization of structural alloys used in Fluoride Cooled High Temperature Reactors (FHR) can result from the interaction between the metal and graphite components and cause changes in alloy properties. However, carburization requires transport of carbon from graphite to alloy surfaces through the molten fluoride coolant. This work introduces an alternative to previously proposed carbon transport mechanisms. The new mechanism is based on the generation of carbonate ions (CO 3 2- ) by oxide impurities in the salt reacting with graphite. CO 3 2- is then reduced on metal surfaces to deposit carbon. This work demonstrates the reduction of dissolved CO 3 2- on pure Fe, Ni, Cr, Mo, and W surfaces without an applied potential in molten FLiNaK at 700 °C. Finally, we also demonstrate that the interaction between oxide and graphite in molten FLiNaK media produces CO 3 2- .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Periodic Trends in Adsorption Energies around Single-Atom Alloy Active Sites

Single-atom alloys (SAAs) make up a special class of alloy surface catalysts that offer well-defined, isolated active sites in a more inert metal host. The dopant sites are generally assumed to have little or no influence on the properties of the host metal, and transport of chemical reactants and products to and from the dopant sites is generally assumed to be facile. Here, by performing density functional theory calculations and surface science experiments, we identify a new physical effect on SAA surfaces, whereby adsorption is destabilized by ≤300 meV on host sites within the perimeter of the reactive dopant site. We identify periodic trends for this behavior and demonstrate a zone of exclusion around the reactive sites for a range of adsorbates and combinations of host and dopant metals. Experiments confirm an increased barrier for diffusion of CO toward the dopant on a RhCu SAA. Furthermore, this effect offers new possibilities for understanding and designing active sites with tunable energetic landscapes surrounding them.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Elementally Resolved Dissolution Kinetics of a Ni-Fe-Cr-Mn-Co Multi-Principal Element Alloy in Sulfuric Acid Using AESEC-EIS

Atomic emission spectroelectrochemistry (AESEC) combined with linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) provided insights on both active and passive dissolution of Ni-Fe-Cr-Mn-Co multi-principal element alloy. Elemental dissolution rates measured by AESEC during open circuit experiment were in agreement with those extrapolated from AESEC-LSV and indicated element-specific dissolution tendencies. AESEC-EIS at open circuit potential showed nearly in-phase elemental dissolution during potential modulation which suggests direct dissolution from the alloy surface to the electrolyte. In the passive potential domain, no oscillation of the elemental dissolution rate was detected by AESEC-EIS, suggesting non-oxidative chemical dissolution of the outer layer of the passive film. In this case, dissolution at the passive film/electrolyte interface was equal to the metal oxidation rate (passive current density) at the metal/passive film interface and the passive current density was independent of potential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evolution of Microstructure and Surface Characteristics of FeCrAl alloys when Subjected to Flow Boiling Testing

FeCrAl alloys are candidate materials for manufacturing accident-tolerant fuel (ATF) cladding intended for light water reactors to increase fuel reliability and safety during design-basis and beyond-design-basis accident scenarios. The evolution of the materials' surface characteristics, microstructure, and mechanical properties when exposed to the Critical Heat Flux (CHF) in flow boiling testing is crucial for safety analysis while providing insights into their thermal-hydraulic performance in nuclear reactors. After CHF, the surface chemistry of two FeCrAl alloys, APMT and C26M, was studied to understand their evolution at the early stage of high-temperature excursions in short time periods. The results indicated a thin layer composed of oxides and hydroxides of Al, Cr, and Fe with varying proportions at different depths in the layer, as indicated by X-ray photoelectron spectroscopy (XPS) and depth profiling. The cross-sections prepared by focused ion beam (FIB) revealed the growth of an oxide layer, in the range of 90-180 nm thick, on the alloys' surfaces. The evolution of the materials' surface chemistry also led to a noticeable post CHF excursion increase in their wettability, with a slight increase in roughness. Further, the investigation of the materials' mechanical properties indicated a modest increase in hardness by 10-15% as well as an increase in their yield strength, as evidenced by the microindentation and ring compression tests conducted before and after CHF testing. Scanning electron Microscopy (SEM) and X-ray diffraction (XRD) were used to investigate microstructural features of the materials and their changes after CHF treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling the Effect of Surface Platinum–Tin Alloys on Propane Dehydrogenation on Platinum–Tin Catalysts

Uncertainty analysis, reported experimental literature data, and density functional theory were synthesized to model the effect of surface tin coverage on platinum-based catalysts for nonoxidative propane dehydrogenation to propylene. Here, this study tests four different platinum–tin skin surface models as potential catalytic sites, Pt 3 Sn/Pt(100), PtSn/Pt(100), Pt 3 Sn/Pt(111), and Pt 2 Sn/Pt(211), and compares them to the corresponding pure Pt surface sites using an uncertainty analysis methodology that uses BEEF-vdW with its ensembles (BMwE) to generate the uncertainty for the energies of the intermediates and transition states. One experimental data set with two experimental observations, selectivity to propylene and turnover frequency of propylene, was used as a calibration data set to evaluate the impact of the experimental data on informing the models. This study finds that the prior model for Pt 3 Sn/Pt(100) is the most active and Pt 2 Sn/Pt(211) is the most selective toward propylene. Active sites on the (100) facet have the highest probability of being responsible for C 1 and C 2 product formations (C–C bond cleavage). Increasing the Sn coverage on the (100) surface facet to a PtSn/Pt(100) active site leads to a significantly reduced rate and might explain the experimentally observed higher selectivity of Sn-doped catalysts relative to pure Pt catalysts. Next, this study finds that for all surfaces, except PtSn/Pt(100), the rate-controlling steps are the initial dehydrogenation steps alongside some partially rate-controlling second dehydrogenation steps. For PtSn/Pt(100), only the initial terminal dehydrogenation step to CH 3 CH 2 CH 2 * and second dehydrogenation steps are rate-controlling. Next, the calibrated models for all surfaces were found to be selective toward propylene production and model the reported turnover frequency successfully. Nevertheless, Pt 2 Sn/Pt(211) emerges as the active site with some (minor) evidence as the main active site based on Jeffreys’ scale interpretation of Bayes factors. This observation agrees with prior studies that also found step sites to be most likely the most relevant active sites for pure Pt catalysts. Overall, the results indicate that tin, in addition to affecting the binding strength of the adsorbed species, prevents deeper dehydrogenation (reducing coking) and cracking reactions through increasing activation barriers for unwanted side reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Selective laser melting of oxide dispersion strengthened MA956 alloy and its surface finishing by magnetic field assisted finishing

Selective laser melting (SLM) is a prominent metal additive manufacturing (AM) capable of processing a myriad of engineering materials with high precision and design freedom. However, similar to other AM processes, poor surface finishing has been an omnipresent problem in SLM technology. In this study, magnetic field assisted finishing (MAF) was used to finish SLM fabricated oxide dispersion strengthened (ODS) MA956, an iron-chromium-aluminum alloy. The effect of laser processing parameters on part density and surface roughness was first studied. Using a multi-objective optimization technique, the optimal parameters to obtain the highest density and lowest surface roughness were determined. Finally, MAF was applied to the parts built with the obtained optimal SLM parameters, but without significant improvement on the surfaces of as-printed samples. Hence, the surfaces of as-printed samples were post-processed (ground) to yield better initial surface conditions prior to MAF. The effect of initial roughness, iron particles size, and abrasive size on MAF performance was studied. Initial roughness had the most dominant effect followed by abrasive size. The underlying mechanism behind the dependency on initial roughness on final surface quality was analyzed by studying the change on the surface profiles with different starting initial roughness. The initial roughness required for MAF to be effective was determined. In conclusion, using the optimal processing conditions, MAF was applied to the post-processed samples to attain the final average surface roughness (R a ) as little as 0.36 μm starting from initial average roughness (R a ) of 1.53 μm.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Surface-hardened aluminum-rare earth alloys and methods of making the same

Embodiments of surface-hardened aluminum-rare earth alloys and methods of making the alloys are disclosed. In some embodiments, the alloy comprises aluminum and 4 wt % to 60 wt % of a rare earth component X having a maximum solid solubility of ≤0.5 wt % in aluminum. The surface-hardened alloy component has an alloy bulk portion and a hardened alloy surface portion. At least a portion of the hardened alloy surface portion has a Vickers hardness that is at least 30% greater than a Vickers hardness of the alloy bulk portion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Laser Surface Processing of Alloys for Corrosion Protection (Final Project Report of Marine Energy Seedling Project)

This is the final project report for the MHK Seedling project. The report describes use of laser surface processing (LSP) to modify the surface of test materials (Al, steel) and the corrosion testing performed on the resulting samples in different corrosion environments. Data shows that LSP improved the corrosion resistance of Al and steel used in this work relative to respective non-LSP samples. The data also showed that each material had a specific range of laser processing conditions where the beneficial effects of LSP (i.e. improvement in corrosion protection) were observed. Application of LSP to enable low-cost materials in marine environments, additional microstructural analysis and long-term testing are proposed to further develop this technology for marine renewable energy and systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Surface facet dependence of competing alloying mechanisms

Metal alloys are ubiquitous in many branches of heterogeneous catalysis, and it is now fairly well established that the local atomic structure of an alloy can have a profound influence on its chemical reactivity. While these effects can be difficult to probe in nanoparticle catalysts, model studies using well defined single crystal surfaces alloyed with dopants enable these structure–function correlations to be drawn. The first step in this approach involves understanding the alloying mechanism and the type of ensembles formed. In this study, we examined the atomic structure of RhCu single-atom alloys formed on Cu(111), Cu(100), and Cu(110) surfaces. Our results show a striking difference between Rh atoms alloying in Cu(111) vs the more open Cu(100) and Cu(110) surface facets. Unlike Cu(111) on which Rh atoms preferentially place-exchange with Cu atoms in the local regions above step edges leaving the majority of the Cu surface free of Rh, highly dispersed, homogeneous alloys are formed on the Cu(100) and (110) surfaces. These dramatically different alloying mechanisms are understood by quantifying the energetic barriers for atomic hopping, exchange, swapping, and vacancy filling events for Rh atoms on different Cu surfaces through theoretical calculations. Density functional theory results indicate that the observed differences in the alloying mechanism can be attributed to a faster hopping rate, relatively high atomic exchange barriers, and stronger binding of Rh atoms in the vicinity of step edges on Cu(111) compared to Cu(110) and Cu(100). Furthermore, these model systems will serve as useful platforms for examining structure sensitive chemistry on single-atom alloys.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗