SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of applying thrust along with optimum aerodynamic control surface defections on incipient and developed spin-recovery characteristics of four aircraft configurations
A pore-volume analysis was performed on water vapor adsorption data previously obtained on a fresh sample of Taurus-Littrow orange soil, and the analysis was repeated on the same sample after its exposure to moist air for a period of approximately six months. The results indicate that exposure of an outgassed sample to high relative pressures of water vapor can result in the formation of substantial micropore structure, the precise amount being dependent on the sample pretreatment, particularly the outgassing temperature. Micropore formation is explained in terms of water penetration into surface defects. In contrast, long-term exposure to moist air at low relative pressures appears to reverse the process with the elimination of micropores and enlargement of mesopores possibly through surface diffusion of metastable adsorbent material. The results are considered with reference to the storage of lunar samples.
Hard carbon (HC) is the state-of-the-art anode material for sodium-ion batteries; however, the high-temperature carbonization of precursors (>1100 °C) often introduces inorganic impurities, an issue that remains largely underexplored. Here, we report a simple synthesis strategy for producing high purity HC by carbonizing a cellulose-derived precursor at 1400 °C under a slightly reducing Ar–H2 atmosphere on a graphite substrate, thereby eliminating the aluminum contamination observed during conventional carbonization on an alumina substrate under Ar. In addition, the modified synthetic condition reduces surface defects and the concentration of oxygen-containing functional groups, thereby altering the interphase formation on the HC surface. At a current density of 20 mA g−1, the impurity-rich HC exhibited an initial coulombic efficiency (ICE) of 74.1% and a reversible capacity of 248.8 mAh g−1. In sharp contrast, the high purity HC delivered a significantly improved ICE of 90.1% and a reversible capacity of 345.1 mAh g−1. These results underscore the critical importance of impurity and defect control during HC synthesis and highlight the clear electrochemical advantages of high purity HC with reduced defects for sodium-ion battery anodes.
Abstract Barite (BaSO 4 ) crystals are an important additive in lead acid batteries due to their ability to promote the controlled nucleation and growth of anglesite (PbSO 4 ) during battery cycling. This is due to BaSO 4 ’s isostructural match with PbSO 4 , which facilitates epitaxial nucleation. However, BaSO 4 ’s efficacy as a nucleation promoter is limited by lattice mismatches between the two phases of 1–5%. Here, strontium‐enriched barite, (Ba,Sr)SO 4 , is synthesized to produce a nucleating promoter that displays an improved lattice match with PbSO 4 . Nucleation of PbSO 4 from Pb‐rich sulfuric acid solutions on strontium‐free and strontium‐enriched barite (up to 17 mol% Sr) is investigated using in‐situ atomic force microscopy and optical microscopy. At low strontium concentrations, PbSO 4 forms by the Stranski–Krastanov growth pathway (monolayer + island formation), with most nucleation occurring on edges and surface defects. At higher concentrations, the layer‐by‐layer growth mechanism known as Frank van‐der‐Merwe growth is observed, which allows for facile growth of continuous PbSO 4 films across the BaSO 4 surface. These films are successfully re‐dissolved on exposure to Pb‐free sulfuric acid. The results show that strontium incorporation fundamentally alters the mechanism of PbSO 4 nucleation on BaSO 4 , and thus provides a potential avenue for creating improved nucleation promoters in lead‐acid batteries.
Lanthanide-doped upconversion nanoparticles are attractive single-molecule imaging probes due to their high photostability and anti-Stokes luminescence. However, achieving both small particle size and strong brightness has remained a major challenge, as reducing size often leads to dimmer emission. Herein, we fabricate a sub-10 nm cascade actively protected upconversion nanoparticles, which shows a 33-fold enhanced upconversion efficiency at the single-particle level compared to larger ~19 nm conventional nanoparticles. Theoretical modeling and time-resolved measurements show that emission loss mainly comes from energy leakage of Er 3+ ions to surface defects. By introducing a NaYbF 4 layer as photon-harvesting and protective intermediate layer, we minimize this energy loss and significantly boost brightness. A monolayer of inert NaLuF 4 can effectively suppress the surface quenching to Yb 3+ . Using these ultra-small bright probes, we successfully tracked single epidermal growth factor receptor molecules on live cells for up to one hour, revealing dynamic switching between different diffusion modes.
An imaging technique based on the radiative recombination of minority carriers in forward-biased solar cells has been developed for characterization of III-V solar cells. When used in mapping whole wafers, it has helped identify three independent loss mechanisms (broken grid lines, shorting defects, and direct-to-indirect bandgap transitions), all of which resulted in lower efficiencies. The imaging has also led to improvements in processing techniques to reduce the occurrence of broken gridlines as well as surface defects. The ability to visualize current mechanisms in solar cells is an intuitive tool which is powerful in its simplicity.
The performance of composite materials is dependent on the constituent materials selected, material structural geometry, and the fabrication process. Flaws can form in composite materials as a result of the fabrication process, handling in the manufacturing environment, and exposure in the service environment to anomalous activity. Often these flaws show no indication on the surface of the material while having the potential of substantially degrading the integrity of the composite structure. For this reason it is important to have available inspection techniques that can reliably detect sub-surface defects such as inter-ply disbonds, inter-ply cracks, porosity, and density changes caused by variations in fiber volume content. Many non-destructive evaluation techniques (NDE) are capable of detecting sub-surface flaws in composite materials. These include shearography, video image correlation, ultrasonic, acoustic emissions, and X-ray. The difficulty with most of these techniques is that they are time consuming and often difficult to apply to full scale structures. An NDE technique that appears to have the capability to quickly and easily detect flaws in composite structure is thermography. This technique uses heat to detect flaws. Heat is applied to the surface of a structure with the use of a heat lamp or heat gun. A thermographic camera is then pointed at the surface and records the surface temperature as the composite structure cools. Flaws in the material will cause the thermal-mechanical material response to change. Thus, the surface over an area where a flaw is present will cool differently than regions where flaws do not exist. This paper discusses the effort made to thermo-mechanically model the thermography process. First the material properties and physical parameters used in the model will be explained. This will be followed by a detailed discussion of the finite element model used. Finally, the result of the model will be summarized along with recommendations for future work.
Metal oxide surfaces possess unique properties that are crucial for a wide variety of applications. Herein, density functional theory calculations are performed to study surfaces of potassium hollandite, KMn 8 O 16 , a promising cathode material for electrochemical energy storage, and the vanadium-substituted analog KMn 7 VO 16 . The results show that there is a clear increase in the stability of KMn 8 O 16 with (001) < (110) < (100) or (010), apt to adopt an elongated rod-like morphology. The vanadium (V)-substitution lowers the crystal symmetry and prefers to occupy the surface sites, resulting in electron redistribution and selective tuning of surface energy depending on the surface structures. In particular, the higher stability of substituted V 4+ compared with Mn 4+ ions leads to stabilization of the (001) surface due to the direct interaction of reduced Mn δ+ ions on the surface, while such tuning effect decreases with the increase in surface stability, (110) > (100) and (010). As a result, the KMnO 16 rod is shortened upon V-substitution as observed experimentally, effectively facilitating the ion transport during discharge. The V substituents also introduce stabilization to the defect surfaces resulting from Mn 2+ dissolution during cycling, thereby hindering further structural decay. In conclusion, our study demonstrates the potential tuning effect of V-substitution to promote the ion transport and mitigate the capacity degradation of α-MnO 2 -based materials.
Green hydrogen (H 2 ) production from solar water splitting necessitates photoelectrodes with superior photoelectrochemical (PEC) activity and durability. However, surface defects and photocorrosion instability—especially at high potentials—limit PEC performance and stability. Herein, the prototypical bismuth vanadate (BiVO 4 ) photoanode is used to demonstrate a holistic approach to improve photocurrent density and long-term stability. In this approach, high surface-area nanostructuring of BiVO 4 is combined with barium (Ba) doping with semi-crystalline hafnium oxide (HfO 2 ) surface passivation and single-atom nickel platinum (NiPt) catalysts. The introduction of Ba 2+ ions into BiVO 4 increases the concentration of conductive V 4+ ions or the ratio of V 4+ ions to oxygen vacancies, avoiding V 5+ dissolution during water oxidation. The semi-crystalline HfO 2 , which serves as a passivation layer, prevents BiVO 4 photocorrosion by suppressing harmful chemical reactions when holes are transferred to the electrolyte. The synergistic use of isolated single-atom and Ni-Pt coordination improves charge transfer at the photoanode/electrolyte interface, leading to enhanced PEC kinetics and stability. As a result, a photoelectrode is demonstrated with ≈6.5 mA cm -2 at 1.23 V versus a reversible hydrogen electrode (RHE) and continuous operation for 800 h with a negligible degradation rate. This work provides a promising approach to improve photoanodes for PEC H 2 production.
In this work we explore the impact of Ultrasonic Impact Treatment (UIT) on the fatigue performance of high‐strength microalloyed steel commonly used in crankshaft applications. Building on prior observations of fatigue life improvement with UIT, this work focuses on unraveling the process–structure–performance relationships underpinning these enhancements. Microstructural analysis revealed significant grain refinement in the near‐surface layers, with deformation depth increasing at higher impact energies. This led to increased surface hardness and the development of deeper compressive residual stresses, particularly in samples treated with higher impact energy. Rotating bending fatigue testing showed a substantial improvement in fatigue life for UIT‐treated samples, with the endurance limit nearly doubling compared with untreated specimens. Fractographic analysis revealed a transition in crack initiation from surface defects in untreated samples to interior regions in UIT‐treated samples, characterized by the formation of noninclusion‐induced granular bright facets (GBFs). The observed fatigue enhancement is attributed to the synergistic effects of strain hardening and compressive residual stresses, which increase the surface crack threshold and promote interior crack initiation. This study provides new mechanistic insight into UIT‐induced fatigue resistance and interior failure behavior in high‐strength steels.
Nanoconfined electrocatalysts demonstrate enhanced selectivity and activity owing to new phenomena emerging from chemical species confined at the interface. Creating these nanoconfined pockets at the interface is not trivial. We need highly negative potentials to create the pockets in metal/ligand catalysts like Ag-nanoparticle/ordered ligand interlayer catalysts. Lowering this activation potential can make the electrocatalysis more energy-efficient, and changes in the environment can impact this potential. We used Density Functional Theory (DFT) to evaluate the impact of ligand length and density, interfacial protons, and surface defects like Ag vacancies and Cu and Au dopants. The nanoconfined configuration is stabilized when the ligands are longer and more densely packed, leading to better agglomeration. It is also stabilized when the ligands adsorb protons and when the ligands detach from the surface easily owing to lower charge transfer. Au-doped surfaces displayed the lowest charge transfer and decreased the activation potential.
New sources of rare earth elements (REEs) are needed to support a green energy transition. REEs adsorbed to aluminum-rich clays in weathering deposits represent important resources but the mechanisms responsible for their retention and ease of extraction are unresolved. Disordered coordination and co-occurrence of multiple species pose challenges to investigating REE adsorption processes via established spectroscopic methods. In this study, we applied element-specific surface crystallography methods to obtain a new perspective on the complexity of REE adsorption mechanisms and affinities. Alumina (001) and (012) crystal surfaces were utilized to evaluate surface-specific controls on Nd(III) and Yb(III) adsorption behavior. The REEs displayed similar total adsorption to alumina (001) as a mixture of inner- and outer-sphere complexes, but Nd displayed a greater proportion of inner-sphere binding. Adsorption of ordered inner- and outer-sphere REE species was substantially lower on alumina (012). These distinct behaviors reflect differences in the surface functional group charging and topography of the two surfaces. However, alumina (012) also hosted a substantial population of disordered adsorbed species, especially for Nd, potentially associated with Al vacancy surface defects. Here, the accumulation of light versus heavy REEs via adsorption in weathering deposits likely results from multiple, competing reactions affected by clay particle morphology. Leaching procedures for resource recovery should account for differential rates of desorption by coexisting inner- and outer-sphere REE surface complexes.
In the present evaluation of results from studies of the interfacial chemistry and morphology of a buried lubricant-substrate interface, specimens of increasing complexity that culminated with the effects of excess sulfur and defects were characterized by XPS and SEM, as well as conversion-electron Moessbauer spectroscopy (CEMS). In order to simulate sputtered systems, single crystals of MoS2 were damaged with Ar(+) bombardment and coated with Fe. Fe is found to react differently with MoS2 depending on surface treatments, surface defects, annealing treatments, and the presence of excess sulfur. The annealing temperature determines which compounds are formed, as well as the crystal habit and plane at the Fe-MoS2 interface.
Focused ion beam (FIB) milling is a commonly used tool for nanoscale material processing, such as for transmission electron microscopy (TEM) sample preparation, or the creation of fiducial markers prior to other processes and measurements. During milling, a high energy ion beam is used to remove material via sputtering. The expelled target material may return to the sample surface however, affecting subsequent measurements. Beam spreading or irradiation due to neutral gallium may also irradiate a larger area than intended. Extensive research has explored the effects of FIB milling on the prepared TEM sample, but few have looked at the effects of milling on the properties of the sample surrounding the milled region. We use multiple pump-probe laser-based techniques (time domain thermoreflectance and steady-state thermoreflectance) to measure the spatial extent of FIB-induced surface/subsurface changes on a series of silicon wafers milled at multiple currents and doses. We supplement these measurements with high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy, stylus profilometry, and time-of-flight secondary ion mass spectroscopy. We find a sample surface affected by the FIB up to 1 mm from where milling occurred, with a notable dependence on the ion beam current. We also note remarkably high sensitivity to surface defects using the thermoreflectance metrologies, including detection where other measurements failed.
Perfect-crystal neutron interferometry, which is analogous to Mach-Zehnder interferometry, uses Bragg diffraction to form interfering neutron paths. The measured phase shifts can be used to probe many types of interactions whether it be nuclear, electromagnetic, gravitational, or topological in nature. For a perfect-crystal interferometer to preserve coherence, the crystal must possess a high degree of dimensional tolerance as well as being relatively defect-free with minimal internal stresses. In the past, perfect-crystal neutron interferometers have been produced by a two-step process. First, a resin diamond wheel would be used to remove excess material and shape the interferometer. Afterword, the crystal would be etched to remove surface defects and elevate strains. This process has had limitations in terms of repeatability and in maximizing the final contrast, or fringe visibility, of the interferometer. We have tested various fabrication and post-fabrication techniques on a single perfect-crystal neutron interferometer and measured the interferometer's performance at each step. Here we report a robust, nonetching fabrication process with high final contrast. For the interferometer used in this work, we achieved contrasts of greater than 90% several times and ultimately finished with an interferometer that has 92% contrast and a uniform phase distribution. Published by the American Physical Society 2024
LDRD Project 229427 aimed to determine how electrothermal instability (ETI) driven heating on a z-pinch rod pulsed with intense current evolves under mixed magnetic field (azimuthal + axial) conditions, which is pertinent to pulsed-power-driven magnetically-insulated transmission lines and physics targets. Experiments focused on diagnosing ETI-driven heating from deliberately-machined and well-characterized micron-scale surface defects (referred to as engineered defects or ED). Prior to the start of this project, understanding of how unmagnetized (B z =0) ED evolve had been obtained—simulations largely reproduce the experimentally observed high temperature spots which develop at the poles of bare/uncoated ED. Project 229427 extended the Mykonos Facility ED experimental platform to include axial field. In the first class of experiments, axial field was provided “dynamically” via a helical return can (HRC). In this case, B z and B θ rise at the same rate. Generally, the HRC generated magnetic field at a fixed polarization angle Φ B =arctan(B z /B θ )=15° on the rod's surface. In the second class of experiments, axial field was provided “statically” via a slow-rising (millisecond) external Helmholtz coil pair. In this case, B z was effectively constant/static throughout the 100 ns rise of the Mykonos current. For either case, a primary goal was to determine whether ETI provides a helical seed perturbation for the subsequent growth of the helical magneto Rayleigh-Taylor modes observed in MagLIF (static B z ) and dynamic screw pinch (DSP, dynamic B z ) experiments. When dynamic field was applied using an HRC, emissions from individual ED aligned toward Φ B , while emissions from ED within pairs elongated and preferentially merged along Φ B . These data strongly support that for a randomized defect distribution, heating from nearby current-density perturbations will favorably merge about Φ B to generate an extended seed perturbation that aligns toward the surface-field polarization, and this may impact the orientation of subsequent MRT growth on imploding liners. The results from the static field experiments were largely inconclusive, as any ETI heating rotation, if present, was obscured/overwhelmed by local/random heating from ED rim imperfections.
The overall objective of the experiment was to evaluate the effect of the space environment on components considered for a Space-Based Radar (SBR) Phased-Array Antenna. Of primary interest was a study of the degradation of the polyimide film Kapton (DuPont trademark), the material considered for use in the antenna plane. The most striking result of the experiment was the overall good condition of the Kapton antenna planes and Kapton tensile specimens, despite nearly six years of exposure to the space environment. This was largely attributable to the orientation of the Kapton (parallel and flush on the space end) and the stability of the Long Duration Exposure Facility (LDEF) in orbit. However, weathering of exposed Kapton surfaces was not insignificant. Results on elongation and mechanical properties of the plain and the fiberglass-reinforced Kapton are presented. Reduction in strain to failure of flight-exposed Kapton is attributed to surface defects of these specimens. Physical property testing of the materials to date reveals no significant difference between flight-exposed and control material. The second objective was to investigate the interaction between high-voltage electrodes and typical spacecraft contaminants in simulation of discharge triggering across differentially charged dielectric surfaces (spacecraft charging conditions). Electronic data acquisition and memory systems appeared to operate correctly, but very few discharges were recorded. Induced radioactivity, contamination, impacts, and orientation features of atomic oxygen erosion were observed.
The development of efficient photocatalytic materials has intensified in response to increasing emphasis on sustainable energy conversion and environmental restoration. However, the excessive use and indiscriminate release of heavy metals from photocatalytic nanoparticles pose potential environmental risks. This study provides insights into optimizing visible-light-active photocatalysts to enhance their photocatalytic properties and stability. Specifically, cobalt doping and controlled pH modulation are employed on the modified Fe 3 O 4 , forming two distinct samples: Co@Fe 3 O 4 -B (base-treated) and Co@Fe 3 O 4 -A (acid-treated) nanoparticles. Microscopic characterization reveals that Co@Fe 3 O 4 -A undergoes a phase transition to hematite, whereas Co@Fe 3 O 4 -B retains its mixed-phase configuration. Spectroscopic analyses confirm that the cobalt dopants decorate the outskirts of each nanoparticle, forming a core–shell structure. However, Co@Fe 3 O 4 -B exhibit Co 2+ states with a high oxygen vacancy content, whereas Co@Fe 3 O 4 -A contain mixed Co 2+/3+ states. The high density of defect states in the Co@Fe 3 O 4 -B results in superior photocatalytic efficiency, achieving near-complete oxidation of furfuraldehyde (97% conversion) and 5-hydroxymethylfurfural (94% conversion), as well as effective degradation of toluene (78% conversion). This study demonstrates that the combined approach of doping and pH treatment is promising for the surface-defect engineering of photocatalysts, enhancing their multifunctional performance and reusability for sustainable energy conversion.