Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface planarization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Efficient passivation of n-type and p-type silicon surface defects by hydrogen sulfide gas reaction

An efficient surface defect passivation is observed by reacting clean Si in a dilute hydrogen sulfide-argon gas mixture (< 5% H2S in Ar) for both n-type and p-type Si wafers with planar and textured surfaces. Surface recombination velocities of 1.5 and 8 cm/s are achieved on n-type and p-type Si wafers, respectively, at an optimum reaction temperature of 550oC that are comparable to the best surface passivation quality used in high efficiency Si solar cells. Surface chemical analysis using x-ray photoelectron spectroscopy shows that sulfur is primarily bonded in a sulfide environment, and synchrotron-based soft x-ray emission spectroscopy of the adsorbed sulfur atoms suggests the formation of S-Si bonds. Furthermore, the sulfur surface passivation layer is unstable in air, attributed to surface oxide formation and a simultaneous decrease of sulfide bonds. However, the passivation can be stabilized by a low-temperature (300oC) deposited amorphous silicon nitride (a-Si:NX:H) capping layer.

14 SOLAR ENERGY↗
DOE OSTI2025

Effect of Thermal Oxidation on the Structure, Surface Texturing, and Microstructure Evolution in Nanocrystalline Ga-O-N Films

An extensive examination of the nanoscale, crystallographic growth dynamics of the system, which is impacted by the thermal energy given to the GaN, is carried out to derive a deeper understanding of the growth kinetics, morphology and microstructure evolution, chemical bonding, and optical properties of Ga-O-N films. Thermal annealing of GaN films is performed in the temperature range of 900–1200 °C. Crystal structure, phase formation, chemical composition, surface morphology, and microstructure evolution of Ga-O-N films are investigated as a function of temperature. Increasing temperature induces surface oxidation, which results in the formation of stable β-Ga2O3 phase in the GaN matrix, where the overall film composition evolves from nitride (GaN) to oxynitride (Ga-O-N). While GaN surfaces are smooth, planar, and featureless, oxidation induced granular-to-rod shaped morphology evolution is seen with increasing temperature to 1200 °C. The considerable texturing and stability of the nanocrystalline Ga-O-N on Si substrates can be attributed to the surface and interface driven modification because of thermal treatment. Corroborating with structure and chemical changes, Raman spectroscopic analyses also indicate that the chemical bonding evolution progresses from fully Ga-N bonds to Ga-O-N. While the GaN oxidation process starts with the formation of β-Ga 2 O 3 at an annealing temperature of 1000 °C, higher annealing temperatures induce structural distortion with the potential formation of Ga-O-N bonds. The structure-phase-chemical composition correlation, which will be useful for nanocrystalline materials for selective optoelectronic applications, is established in Ga-O-N films made by thermal treatment of GaN.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Alloying of Mn with Bi‐Rich Surfaces of Bi 2 Te 3 by Topotactic Reaction

Interfacing topological insulators (TI) with magnetic materials enables accessing quantum effects for advanced devices. The synthesis of such heterostructures faces challenges due to interlaying mixing and the often-complex multicomponent materials required to combine the desired properties. An alternative synthesis to direct growth is the modification of 2D materials by topotactic reactions to introduce new functionalities into pre-formed single or few-component 2D sheets. Here, the self-formation of bismuthene (a bilayer of Bi; Bi 2 ) is utilized by thermal decomposition of Bi 2 Te 3 as a platform to create novel 2D overlayers on the TI- substrate. Specifically, the Bi 2 layer is modified by reacting it with vapor deposited Mn in an attempt to induce magnetic properties. Scanning tunneling microscopy indicates that the Mn modified surface remains in a planar 2D layer, indicating the formation of an ordered Mn-rich surface layer. Density functional theory (DFT) is used to develop models of both the Bi-rich Bi 2 Te 3 surface as well as their subsequent Mn-modified structure. The DFT models indicate the possibility of magnetic ordering of the high spin Mn 2+ ions. The successful synthesis of planar MnBi alloys on a van der Waals material illustrates topotactic reactions as an alternative for creating novel layered heterostructures.

2D materials↗
DOE OSTI2025

Elastomeric Nanocomposite with Solvent‐Free, One Step, In Situ Shear Exfoliation of Graphite to Graphene

A graphene nanoflake (GNF)‐enhanced elastomeric nanocomposite (G‐EMC) is fabricated following an innovative, cost‐effective, single‐step, in situ shear exfoliation (ISE) method from low‐cost bulk material, graphite, where uniform mixing happens simultaneously within the elastomer matrix. Electron microscopy, atomic force microscopy, and photo‐induced force microscopy results show good dispersion of GNFs with exfoliation to a few layers and uniform distribution in the elastomer matrix. X‐ray photoelectron spectroscopy analysis shows less than 1% oxygen‐containing functional groups/impurity, enhanced bonding through the formation of edge sites as fracture occurs across the GNF basal plane, and pi‐pi interactions with newly exfoliated planar basal plane surfaces of the GNFs. Raman spectroscopy results confirm the formation of GNFs with only a few layers of graphene formed by the ISE process. Fabricated 10 wt.% G‐EMC nanocomposites show a 400%–500% increase in strength and fracture toughness. And 35 wt.% G‐EMCs provide an electrical conductivity of 25.64 S m −1 and a sensor gauge factor of 45. The resulting intrinsic piezo resistivity of the fabricated nanocomposite has been exploited to fabricate a multi‐functional wired and wireless sensor for detecting different body movements, speech, human vital functions, solvents, and biomolecules.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design, fabrication, simulation, and testing of additively manufactured lattice-based copper heat sinks

Here, this study investigates the potential advantages of lattice structure-based bound metal material extrusion (MEX) 3D printing for fabricating high-performance copper heat sinks. Copper powder-filled polymer filaments, with a copper content of > 90 wt.%, were developed specifically for the bound metal MEX 3D printing process. Three types of structures—planar, strut, and surface lattices—were 3D printed to facilitate efficient heat transfer pathways within the heat sinks. Subsequent post-processing steps, including polymer removal and sintering, were performed to achieve dense copper parts. Hot isostatic pressing was further employed to enhance the sintered density from 93 to 98%. Finite element analysis (FEA) simulations were conducted to assess the heat transfer efficiency of the designs, and heat transfer experiments were performed using a custom setup to validate the simulation results. Additionally, this research explores the use of extended hold times during pre-sintering and a reduced atmosphere to enhance the %IACS values (electrical conductivity) and thermal performance of the bound metal MEX 3D printed copper heat sinks. The investigation combines experimental analysis, including simulations and heat transfer experiments, to gain insights into the structure-material property relationships and optimize the thermal performance of the printed heat sinks.

Ajjarapu, Kameswara Pavan Kumar [Oak Ridge Nationa↗
DOE OSTI2026

Oak Ridge National Laboratory Building Envelope Library (ORNOBEL)

The Oak Ridge National Laboratory Building Envelope Library (ORNOBEL) is a collection of dense exterior building-facade point clouds acquired using a survey-grade terrestrial laser scanner. Each file represents an individual facade from a building on the Oak Ridge National Laboratory (ORNL) campus or in Knoxville, Tennessee, with an average point-cloud resolution of approximately 3 mm. The points in each facade are semantically labeled into three classes: (1) window/door, representing openings in the building envelope; (2) wall, representing planar opaque envelope surfaces; and (3) other, representing the remaining facade-adjacent elements, architectural features, and protrusions. ORNOBEL supports the development, training, and evaluation of advanced deep-learning methods for automated building-envelope segmentation, geometric reconstruction, and building information modeling (BIM).

Maldonado Puente, Bryan [ORNL] (ORCID:000000033880↗
DOE OSTI2020

Apparatus and method for facilitating planar delayering of integrated circuit die

An apparatus and method for facilitating the removal of layers from a die for an integrated circuit while maintaining the planarity of the surface of the die by avoiding rounding the corners and other edges of the die. A pocket is created in a sacrificial material, such that when the die is inserted into the pocket the edges of the die are contiguous with the walls of the pocket and a top surface of the die is coplanar with a top surface of the pocket. The sacrificial material may be the same material as the die. An adhesive substance is placed in the pocket, and the die is inserted into the pocket and against the adhesive substance which aids in retaining the die in the pocket. The layers may then be removed from the die and the sacrificial material around the die without rounding the edges of the die.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Apparatus and method for facilitating planar delayering of integrated circuit die

An apparatus and method for facilitating the removal of layers from a die for an integrated circuit while maintaining the planarity of the surface of the die by avoiding rounding the corners and other edges of the die. A pocket is created in a sacrificial material, such that when the die is inserted into the pocket the edges of the die are contiguous with the walls of the pocket and a top surface of the die is coplanar with a top surface of the pocket. The sacrificial material may be the same material as the die. An adhesive substance is placed in the pocket, and the die is inserted into the pocket and against the adhesive substance which aids in retaining the die in the pocket. The layers may then be removed from the die and the sacrificial material around the die without rounding the edges of the die.

Trujillo, Joshua Joseph↗
DOE OSTI2021

Defect-driven selective metal oxidation at atomic scale

Nanoscale materials modified by crystal defects exhibit significantly different behaviours upon chemical reactions such as oxidation, catalysis, lithiation and epitaxial growth. However, unveiling the exact defect-controlled reaction dynamics (e.g. oxidation) at atomic scale remains a challenge for applications. Here, using in situ high-resolution transmission electron microscopy and first-principles calculations, we reveal the dynamics of a general site-selective oxidation behaviour in nanotwinned silver and palladium driven by individual stacking-faults and twin boundaries. The coherent planar defects crossing the surface exhibit the highest oxygen binding energies, leading to preferential nucleation of oxides at these intersections. Planar-fault mediated diffusion of oxygen atoms is shown to catalyse subsequent layer-by-layer inward oxide growth via atomic steps migrating on the oxide-metal interface. These findings provide an atomistic visualization of the complex reaction dynamics controlled by planar defects in metallic nanostructures, which could enable the modification of physiochemical performances in nanomaterials through defect engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

MOCVD Surface Preparation of V-Groove Si for III-V Growth

V-groove nanopatterning of Si substrates has recently demonstrated promise for achieving high-quality III-V-on-Si epitaxy while providing a lower-cost processing route than chemo-mechanical polishing to produce epi-ready planar wafers. A key factor in determining the crystalline quality of III-V buffer layers is the Si surface structure and its chemical composition. Unlike planar Si surfaces, the surfaces of V-grooves prior to growth have not been studied in detail. Here, we study the surface of V-groove Si prepared for GaP nucleation via X-ray photoelectron spectroscopy and low-energy electron diffraction. We identify several pretreatments, using both 830 and 1000 annealing under an As background pressure, as being suitable for deoxidizing and cleaning the V-groove Si surface. The V-groove Si was found to behave similarly to reference Si(0 0 1) and Si(1 1 1) planar samples, demonstrating that in situ techniques such as reflection anisotropy spectroscopy can be used on reference samples to infer the state of the V-groove surface, and indicating that the extensive research on planar Si surfaces can be directly applied to V-grooves.

III-V epitaxy↗
DOE OSTI2021

Hybrid-Lipid Bilayers Induce n -Alkyl-Chain Order in Reversed-Phase Chromatographic Surfaces, Impacting their Shape Selectivity for Aromatic Hydrocarbon Partitioning

Shape selectivity is important in reversed-phase liquid chromatographic separations, where stationary phases are capable of separating geometric isomers, thereby resolving solutes based on their three-dimensional structure or shape rather than other chemical differences. Numerous chromatographic studies have been carried out using n-alkyl-chain-modified columns to understand how molecular shape affects retention. For polycyclic aromatic hydrocarbons (PAHs), it was found that planar compounds were selectively retained over non-planar structures of comparable molecular weight on surfaces with longer n-alkyl chains, higher chain-density, or at lower temperatures, where selectivity likely arises with greater ordering of the n-alkyl chains. A limitation of these studies, however, is the small range of chain ordering that can be achieved and lack of a direct measure of the n-alkyl-chain order of the stationary phases. In this work, we employ a C 18 stationary phase modified with a monolayer of phospholipid as a means of significantly varying the n-alkyl chain order. These hybrid-supported lipid bilayers, which have previously been employed as membrane-like stationary phases for measuring lipophilicity, provide a unique approach to control n-alkyl chain ordering by varying the acyl chain length and degree of unsaturation of the phospholipid modifier. The degree of alkyl-chain order of the resulting modified surfaces is determined from the ratio of trans- versus gauche-conformers, measured in situ within individual porous particles by confocal Raman microscopy. This methodology was also used to assess the affinity of these surfaces for planar versus non-planar PAH molecules. The retention selectivity for the planar versus non-planar compounds, thus determined, was found to vary significantly and systematically with the degree of order of the acyl/alkyl chains in the hybrid-supported lipid bilayers. Furthermore, the investigation also demonstrates the utility of confocal Raman microscopy for interrogating the impact of solute partitioning on stationary-phase structure within porous chromatographic particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Unlocking the Future of Aircraft Manufacturing: The Environmental Benefits of Laser Patterning for Surface Enhancement of Aircraft-Certified Alloys

Surface protection and functional modification of aircraft-certified aluminum alloys are essential for corrosion resistance, durability, and long-term airworthiness. At the same time, increasingly restrictive environmental regulations motivate the development of alternatives to legacy wet-chemical surface treatments. This study presents an integrated assessment of ultrafast femtosecond laser surface texturing as a surface functionalization approach for Aluminum 6061 alloys within an aerospace manufacturing and sustainability context. Ultrashort-pulse laser processing enables controlled micro- and nano-scale surface topographical modification with limited thermal impact, allowing adjustment of wettability and surface functionality while preserving bulk material integrity. As a dry and contactless process, femtosecond laser treatment eliminates the use of hazardous chemicals, reduces consumable inputs, and generates minimal secondary waste. A streamlined cradle-to-gate life cycle assessment conducted in accordance with ISO 14040/14044 indicates a lower global-warming potential per functional unit compared with conventional surface treatments, including anodization, plasma-assisted coatings, and organic coating systems. Complementary qualitative analyses addressing environmental health and safety, supply-chain risk, and ESG alignment indicate potential advantages related to occupational safety, regulatory compliance, waste management, and end-of-life recyclability. The investigation is performed on planar Aluminum 6061 reference surfaces with a treated area of 25 mm 2 , providing a controlled laboratory-scale basis for analyzing process behavior, functional surface modification, and associated environmental metrics. Within this defined scope, the results support further evaluation of femtosecond laser surface texturing as a surface engineering option for future aerospace manufacturing.

corrosion resistance↗
DOE OSTI2021

Toward a Theory of the Evolution of Drop Morphology and Splintering by Freezing

Abstract The drop freezing process is described by a phase-field model. Two cases are considered: when the freezing is triggered by central nucleation and when nucleation occurs on the drop surface. Depending on the environmental temperature and drop size, different morphological structures develop. Detailed dendritic growth was simulated at the first stage of drop freezing. Independent of the nucleation location, a decrease in temperature within the range from ~−5° to −25°C led to an increase in the number of dendrites and a decrease in their width and the interdendritic space. At temperatures lower than about −25°C, a planar front developed following surface nucleation, while dendrites formed a granular-like structure with small interdendritic distances following bulk nucleation. An ice shell grew in at the same time (but slower) as dendrites following surface nucleation, while it started forming once the dendrites have reached the drop surface in the case of central nucleation. The formed ice morphology at the first freezing stage predefined the splintering probability. We assume that stresses needed to break the ice shell arose from freezing of the water in the interdendritic spaces. Under this assumption, the number of possible splinters/fragments was proportional to the number of dendrites, and the maximum rate of splintering/fragmentation occurred within a temperature range of about −10° to −20°C, is in agreement with available laboratory and in situ measurements. At temperatures < −25°C, freezing did not lead to the formation of significant stresses, making splintering unlikely. The number of dendrites increased with drop size, causing a corresponding increase in the number of splinters. Examples of morphology that favors drop cracking are presented, and the duration of the freezing stages is evaluated. Sensitivity of the freezing process to the surface fluxes is discussed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Probing three-dimensional mesoscopic interfacial structures in a single view using multibeam X-ray coherent surface scattering and holography imaging

Abstract Visualizing surface-supported and buried planar mesoscale structures, such as nanoelectronics, ultrathin-film quantum dots, photovoltaics, and heterogeneous catalysts, often requires high-resolution X-ray imaging and scattering. Here, we discovered that multibeam scattering in grazing-incident reflection geometry is sensitive to three-dimensional (3D) structures in a single view, which is difficult in conventional scattering or imaging approaches. We developed a 3D finite-element-based multibeam-scattering analysis to decode the heterogeneous electric-field distribution and to faithfully reproduce the complex scattering and surface features. This approach further leads to the demonstration of hard-X-ray Lloyd’s mirror interference of scattering waves, resembling dark-field, high-contrast surface holography under the grazing-angle scattering conditions. A first-principles calculation of the single-view holographic images resolves the surface patterns’ 3D morphology with nanometer resolutions, which is critical for ultrafine nanocircuit metrology. The holographic method and simulations pave the way for single-shot structural characterization for visualizing irreversible and morphology-transforming physical and chemical processes in situ or operando .

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Advanced low blaze angle x-ray gratings via nanoimprint replication and plasma etch

We developed a new method of making ultra-low blaze angle diffraction gratings for x-ray applications. The method is based on reduction of the blaze angle of a master grating by nanoimprint replication followed by a plasma etch. A master blazed grating with a relatively large blaze angle is fabricated by anisotropic wet etching of a Si single crystal substrate. The surface of the master grating is replicated by a polymer material on top of a quartz substrate by nanoimprinting. Then a second nanoimprinting is performed using the 1st replica as a mold to replicate the saw-tooth surface into a resist layer on top of a Si grating substrate. A reactive ion etch is used to transfer the grating grooves into the Si substrate. The plasma etch provides reduction of the groove depth by a factor defined by the ratio of the etch rates for the resist and Si. We demonstrate reduction of the blaze angle of a master grating by a factor of 5 during fabrication of a 200 lines/mm blazed grating with a blaze angle of 0.2°. We investigated the quality and performance of the fabricated low blaze angle gratings and evaluate process accuracy and reproducibility. The new blaze angle reduction method preserves the planarity of the optical surface of the grating substrate and at the same time provides improvement in the grating groove quality during the reduction process.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

A Sodium–Antimony–Telluride Intermetallic Allows Sodium-Metal Cycling at 100% Depth of Discharge and as an Anode-Free Metal Battery

In this work, repeated cold rolling and folding is employed to fabricate a metallurgical composite of sodium–antimony–telluride Na 2 (Sb 2/6 Te 3/6 Vac 1/6 ) dispersed in electrochemically active sodium metal, termed “NST-Na.” This new intermetallic has a vacancy-rich thermodynamically stable face-centered-cubic structure and enables state-of-the-art electrochemical performance in widely employed carbonate and ether electrolytes. NST-Na achieves 100% depth-of-discharge (DOD) in 1 m NaPF 6 in G2, with 15 mAh cm –2 at 1 mA cm –2 and Coulombic efficiency (CE) of 99.4%, for 1000 h of plating/stripping. Sodium-metal batteries (SMBs) with NST-Na and Na 3 V 2 (PO 4 ) 3 (NVP) or sulfur cathodes give significantly improved energy, cycling, and CE (>99%). An anode-free battery with NST collector and NVP obtains 0.23% capacity decay per cycle. Imaging and tomography using conventional and cryogenic microscopy (Cryo-EM) indicate that the sodium metal fills the open space inside the self-supporting sodiophilic NST skeleton, resulting in dense (pore-free and solid electrolyte interphase (SEI)-free) metal deposits with flat surfaces. The baseline Na deposit consists of filament-like dendrites and “dead metal”, intermixed with pores and SEI. Density functional theory calculations show that the uniqueness of NST lies in the thermodynamic stability of the Na atoms (rather than clusters) on its surface that leads to planar wetting, and in its own stability that prevents decomposition during cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High Miscibility Compatible with Ordered Molecular Packing Enables an Excellent Efficiency of 16.2% in All-Small-Molecule Organic Solar Cells

In all-small-molecule organic solar cells (ASM-OSCs), a high short-circuit current (Jsc) usually needs a small phase separation, while a high fill factor (FF) is generally realized in a highly ordered packing system. However, small domain and ordered packing always conflicted each other in ASM-OSCs, leading to a mutually restricted J sc and FF. Here, in this study, alleviation of the previous dilemma by the strategy of obtaining simultaneous good miscibility and ordered packing through modulating homo- and heteromolecular interactions is proposed. By moving the alkyl-thiolation side chains from the para- to the meta-position in the small-molecule donor, the surface tension and molecular planarity are synchronously enhanced, resulting in compatible properties of good miscibility with acceptor BTP-eC9 and strong self-assembly ability. As a result, an optimized morphology with multi-length-scale domains and highly ordered packing is realized. The device exhibits a long carrier lifetime (39.8 μs) and fast charge collection (15.5 ns). A record efficiency of 16.2% with a high FF of 75.6% and a J sc of 25.4 mA cm –2 in the ASM-OSCs is obtained. These results demonstrate that the strategy of simultaneously obtaining good miscibility with high crystallinity could be an efficient photovoltaic material design principle for high-performance ASM-OSCs.

14 SOLAR ENERGY↗
DOE OSTI2026

Low-Threshold Visible-to-Ultraviolet Solid-State Triplet-Fusion Upconversion

Visible-to-ultraviolet (UV) triplet-triplet annihilation (TTA) upconversion is an energy-relevant photon-management strategy that converts visible photons into UV photons capable of driving high-energy photochemical processes. Practical implementation requires solid-state thin films, which often require high excitation power. Here, we demonstrate the first solid-state visible-to-UV TTA upconversion thin-film device, using 1,4-bis((tricyclopentylsilyl)ethynyl)naphthalene (TCPS-NAP) as the annihilator and tris(2-phenylpyridine)iridium(III) (Ir(ppy) 3 ) as the sensitizer on silver. Under incoherent 455 nm excitation, the device exhibits blue-to-UV upconversion with a threshold of 4.8 mW/cm 2 . Using surface plasmons in the planar silver film, we achieve green-to-UV upconversion with a 1.11 eV anti-Stokes shift and 6.9 mW/cm 2 threshold, a 12.2 × threshold enhancement over far-field 532 nm excitation. In solution, TCPS-NAP shows excimer-dominated anti-Stokes emission rather than UV upconversion. These results establish a platform for harvesting low-intensity visible light to drive UV processes while demonstrating that solution-phase screening does not predict solid-state upconversion performance.

Luminescence↗