Search NASA⌕ Search

SEARCH · Search NASA

Results for “temperature data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

The thermal structure of Jupiter. I - Implications of Pioneer 10 infrared radiometer data

Temperature profiles for low latitude regions of Jupiter in the 1.0-0.1 bar pressure regime are recovered from Pioneer 10 infrared radiometer data. The temperature near 0.1 bar is 108-117 K, depending on the overlying thermal structure assumed. For the South Equatorial Belt (SEB), the temperature at 1.0 bar is 170 K, assuming an adiabatic lapse rate in the deep atmosphere. The South Tropical Zone temperature at this level is 155 K if pure gaseous absorption is assumed. The temperature is much closer to that in the SEB, assuming the presence of an optically opaque cloud near the 0.6 atm (145 K) level. Such a cloud presence in the STrZ may be correlated with the visible and 5 micron appearance of the planet and with NH3 saturation just below this position. The molar fraction of H2 most consistent with the data is 0.91 + or - 0.08. The effective temperatures of the SEB and STrZ are 127.6 and 124.2 K, respectively. A discrepancy with the preliminary neutral atmosphere inversion of Pioneer 10 radio occultation data remains unexplained.

Orton, G. S.↗

Synthesis of passive microwave and radar altimeter data for estimating accumulation rates of polar snow

In this paper, we compare dry-snow extinction coefficients derived from radar altimeter data with brightness temperature data from passive microwave measurements over a portion of the East Antarctic plateau. The comparison between the extinction coefficients and the brightness temperatures shows a strong negative correlation, where the correlation coefficients ranged from -0.87 to -0.95. The extinction coefficient of the dry polar snow decreases with increasing surface elevation, while the average brightness temperature increases with surface elevation. Our analysis shows that the observed trends are related to geographic variations in scattering coefficient of snow, which in turn are controlled by variations in surface temperature and snow accumulation rate. By combining information present in the extinction coefficient and brightness temperature data sets, we develop a model that can be used to obtain quantitative estimates of the accumulation rate of dry polar snow.

Davis, Curt H.↗

Tropical cyclone outer surface winds derived from satellite microwave sounder data

Upper tropospheric temperature anomalies are detected in brightness temperature data from the Nimbus 6 Scanning Microwave Spectrometer (SCAMS). Brightness temperature anomalies are related to surface pressure anomalies through the radiative transfer and hydrostatic equation. Surface wind speeds at outer radii are then estimated using the gradient wind equation and a shearing parameter. The method is first tested using simulated satellite data constructed from temperature, pressure and height data recorded by aircraft reconnaissance of four hurricanes. Wind speeds in the 80-95 kPa region are estimated with 2-3 m/sec accuracy. Next, 55.45 GHz SCAMS data over eight typhoons during 1975 are used to estimate the radii of 15.4 m/sec (30 kt) and 27.5 m/sec (50 kt) winds. Accuracies of about + or - 80 and + or - 70 km, respectively, are found. It is suggested that the technique be further tested using data from the Microwave Sounding Unit on board the TIROS-N and NOAA 6 satellites.

Kidder, S. Q.↗

Comparison of Computational Results with a Low-g, Nitrogen Slosh and Boiling Experiment

This paper compares a fluid/thermal simulation, in Fluent, with a low-g, nitrogen slosh and boiling experiment. In 2010, the French Space Agency, CNES, performed cryogenic nitrogen experiments in a low-g aircraft campaign. From one parabolic flight, a low-g interval was simulated that focuses on low-g motion of nitrogen liquid and vapor with significant condensation, evaporation, and boiling. The computational results are compared with high-speed video, pressure data, heat transfer, and temperature data from sensors on the axis of the cylindrically shaped tank. These experimental and computational results compare favorably. The initial temperature stratification is in good agreement, and the two-phase fluid motion is qualitatively captured. Temperature data is matched except that the temperature sensors are unable to capture fast temperature transients when the sensors move from wet to dry (liquid to vapor) operation. Pressure evolution is approximately captured, but condensation and evaporation rate modeling and prediction need further theoretical analysis.

Cryogenic Fluid Storage↗

Precision Epoch of Reionization Studies with Next-Generation CMB Experiments

Future arcminute resolution polarization data from ground-based Cosmic Microwave Background (CMB) observations can be used to estimate the contribution to the temperature power spectrum from the primary anisotropies and to uncover the signature of reionization near l = 1500 in the small angular-scale temperature measurements. Our projections are based on combining expected small-scale E-mode polarization measurements from Advanced ACTPol in the range 300 < l < 3000 with simulated temperature data from the full Planck mission in the low and intermediate l region, 2 < l < 2000. We show that the six basic cosmological parameters determined from this combination of data will predict the underlying primordial temperature spectrum at high multipoles to better than 1% accuracy. Assuming an efficient cleaning from multi-frequency channels of most foregrounds in the temperature data, we investigate the sensitivity to the only residual secondary component, the kinematic Sunyaev-Zel'dovich (kSZ) term. The CMB polarization is used to break degeneracies between primordial and secondary terms present in temperature and, in effect, to remove from the temperature data all but the residual kSZ term. We estimate a 15 sigma detection of the di use homogeneous kSZ signal from expected AdvACT temperature data at l > 1500, leading to a measurement of the amplitude of matter density fluctuations, sigma 8, at 1% precision.

Precision↗

MISSE 1 and 2 Tray Temperature Measurements

The Materials International Space Station Experiment (MISSE 1 & 2) was deployed August 10,2001 and retrieved July 30,2005. This experiment is a co-operative endeavor by NASA-LaRC. NASA-GRC, NASA-MSFC, NASA-JSC, the Materials Laboratory at the Air Force Research Laboratory, and the Boeing Phantom Works. The objective of the experiment is to evaluate performance, stability, and long term survivability of materials and components planned for use by NASA and DOD on future LEO, synchronous orbit, and interplanetary space missions. Temperature is an important parameter in the evaluation of space environmental effects on materials. The MISSE 1 & 2 had autonomous temperature data loggers to measure the temperature of each of the four experiment trays. The MISSE tray-temperature data loggers have one external thermistor data channel, and a 12 bit digital converter. The MISSE experiment trays were exposed to the ISS space environment for nearly four times the nominal design lifetime for this experiment. Nevertheless, all of the data loggers provided useful temperature measurements of MISSE. The temperature measurement system has been discussed in a previous paper. This paper presents temperature measurements of MISSE payload experiment carriers (PECs) 1 and 2 experiment trays.

Harvey, Gale A.↗

Tropical oceanic precipitation frequency from Nimbus 5 microwave data

Microwave brightness temperature data from the Nimbus 5 satellite are analyzed, using threshold brightness temperatures, to yield tropical oceanic precipitation frequencies for several classes of rainfall rates during the season December 1972 through February 1973. Data taken near local noon and near local midnight are analyzed. The overall results are consistent with both climatological precipitation frequency and with concurrent satellite-derived frequency of highly reflective clouds. The difference between the local noon and local midnight frequencies is small, but the heavier rainfall rates tend to occur more frequently near local noon. The ratios of the frequencies of light, moderate, and heavy rain were observed to be relatively constant over the tropical oceans. Passive microwave measurements from space seem to be an important step toward accurate measurement of oceanic precipitation.

Kidder, S. Q.↗

Comparison of Computational Results with a Low-g, Nitrogen Slosh and Boiling Experiment

The proposed paper will compare a fluid/thermal simulation, in FLUENT, with a low-g, nitrogen slosh experiment. The French Space Agency, CNES, performed cryogenic nitrogen experiments in several zero gravity aircraft campaigns. The computational results have been compared with high-speed photographic data, pressure data, and temperature data from sensors on the axis of the cylindrically shaped tank. The comparison between these experimental and computational results is generally favorable: the initial temperature stratification is in good agreement, and the two-phase fluid motion is qualitatively captured.

Boiling---Phase Transformations↗

Feasibility of solar power for Mars

NASA, through Project Pathfinder, has put in place an advanced technology program to address future needs of manned space exploration. Included in the missions under study is the establishment of outposts on the surface of Mars. The Surface Power program in Pathfinder is aimed at providing photovoltaic array technology for such an application (as well as for the lunar surface). Another important application is for unmanned precursor missions, such as the photovoltaic-power aircraft, which will scout landing sites and investigate Mars geology for a 1 to 2 year mission without landing on the surface. Effective design and utilization of solar energy depend to a large extent on adequate knowledge of solar radiation characteristics in the region of solar energy system operation. The two major climatic components needed for photovoltaic system designs are the distributions of solar insolation and ambient temperature. These distributions for the Martian climate are given at the two Viking lander locations but can also be used, to the first approximation, for other latitudes. One of the most important results is that there is a large diffuse component of the insolation, even at high optical depth, so that solar energy system operation is still possible. If the power system is to continue to generate power even on high optical opacity days, it is thus important that the photovoltaic system be designed to collect diffuse irradiance as well as direct. In absence of long term insolation and temperature data for Mars, the data presented can be used until updated data are available. The ambient temperature data are given as measured directly by the temperature sensor; the insolation data are calculated from optical depth measurements of the atmosphere.

Appelbaum, Joseph↗

Seasonal oceanic precipitation frequencies from Nimbus 5 microwave data

Microwave brightness temperature data from the Nimbus 5 satellite have been analyzed by using threshold brightness temperatures to yield tropical oceanic precipitation frequencies for several classes of rainfall rates during the season December 1972 through February 1973. Data taken near local noon and near local midnight were analyzed. The overall results are consistent with both climatological precipitation frequency and with concurrent satellite-derived frequency of highly reflective clouds. The difference between the local noon and the local midnight frequency is small, but the heavier rainfall rates tend to occur more frequently near local noon. The ratios of the frequencies of light, moderate, and heavy rain were observed to be relatively constant over the tropical oceans. Passive microwave measurements from space seem to be an important step toward accurate measurement of oceanic precipitation.

Kidder, S. Q.↗

Land surface parameterization for regional surface heat transfer in hilly grassland

Radiometrically obtained surface temperature data and wind and temperature data from the atmospheric boundary layer are analyzed to determine the regional surface-heat flux. Monin-Obukhov similarity theory is employed to analyze the wind speed and the relationship between the surface potential temperature and the potential temperature. The radiometric scalar roughness is considered and found to be related to solar elevation and canopy height, although the regional sensible heat flux derived by the similarity theory analysis agrees with measured flux values.

Sugita, Michiaki↗

Estimation of Regional Evapotranspiration Using Remotely Sensed Land Surface Temperature. Part 2: Application of Equilibrium Evaporation Model to Estimate Evapotranspiration by Remote Sensing Technique

In a humid region like Japan, it seems that the radiation term in the energy balance equation plays a more important role for evapotranspiration then does the vapor pressure difference between the surface and lower atmospheric boundary layer. A Priestley-Taylor type equation (equilibrium evaporation model) is used to estimate evapotranspiration. Net radiation, soil heat flux, and surface temperature data are obtained. Only temperature data obtained by remotely sensed techniques are used.

Kotoda, K.↗

Comparison of the poleward transport of ozone in the Northern and Southern Hemispheres

Six and one-half years of ozone data and temperature data are used to extend Geller et al.'s (1988) study comparing the transport of ozone to high latitudes in the Northern and Southern Hemispheres. In this earlier study, it was pointed out that the poleward transport of ozone varies annually in the Northern Hemisphere but has a marked semiannual behavior in the Southern Hemisphere. This earlier study covered the period from December 1978 to November 1982. Two and one-half additional years have now been analyzed so that the analysis now extends to July 1986. With this extended data set, the maximum rate of increase in total ozone is seen to occur in January in the Northern Hemisphere for all of the years investigated. In the Southern Hemisphere, the maximum rate of increase is seen in September for almost all of the years with a secondary maximum in the rate of increase in total ozone often being seen during March-April period. The nature of the seasonal variation in total ozone is found to be much more variable in the Southern Hemisphere than in the Northern Hemisphere.

Geller, Marvin A.↗

Stratospheric temperatures during the 88-89 Northern Hemisphere winter

The Airborne Arctic Stratospheric Expedition (AASE) was conducted during January and February 1989. The polar stratosphere during this period was characterized by cold conditions from January to mid-February. A mid-February wave 2 major warming considerably warmed the polar stratosphere, but did not immediately lead to a lower stratospheric vortex breakup. As inferred from temperature data, January temperatures were sufficient for polar stratospheric cloud (PSC) formation. PSC regional extent was greater than the long-term average, but not significantly larger than in previous years.

Newman, Paul A.↗

Flight Schedule and the Circadian Clock Influence on Sleep Loss During Overnight Cargo Operations

Thirty-four flight crew members were monitored before, during, and after two 8-day overnight cargo duty patterns which involved multiple flights at night crossing no more than one time zone per 24 h. Rectal temperature, heart rate, and wrist activity were recorded every 2 min. Sleep quantity and quality, and nap timing, were noted in a logbook. To reduce the masking effects of physical activity on temperature, 0.28 C was added to each subject's raw temperature data whenever he reported being asleep. For both masked and unmasked data, daily temperature minima were estimated from the multiple complex demodulated waveform. The temperature minima did not show a progressive adaptation to night duty, which was interrupted by a night off after 5 nights on one trip pattern and after 3 nights on the other. On duty days, the average temperature minimum delayed by about 3 h, occurring near the end of the duty period. Daytime sleep episodes averaged 2.9 h shorter than nighttime sleep episodes, and were rated as lighter, less restorative, and poorer overall. Fifty-three percent of subjects slept more than once per 24 h while they were on night duty, compared to 17% when able to sleep at night. The total sleep per 24 h on duty days averaged 1.2 h less than pretrip. Twenty-nine percent of subjects lost more than 2 h of sleep per 24 h across the 8-day duty patterns. After night duty, subjects awoke around 1400 local time, even when they had slept 2-3 h less than a normal nocturnal sleep episode. Consequently, the duration of morning sleep episodes was correlated with the off-duty time (multiple r(sup 2)=0.44, F=37.23, p less than 0.0001). Anecdotally, crew members complained of being unable to sleep longer and not feeling well-rested. These wakeups were clustered 6 h after the temperature minimum, which suggests that they may have been a response to the circadian wakeup signal. Daytime layovers in which crew members were able to sleep again in the evening ended later (0200-0300) and were longer (average 19.2 h versus 14.8 h) than those in which they slept only once in the morning. Overnight cargo crew members are working around the time of the circadian nadir with an accumulating sleep debt. Two scheduling factors affect sleep loss during these operations: how long before the circadian wakeup signal crew members come off duty, and whether the layover lasts long enough to permit a second sleep episode in the early evening.

Gander, Philippa H.↗

Propellant Densification Ground Testing Conducted for Launch Vehicles

The NASA Glenn Research Center at Lewis Field has taken the lead in the development of practical densified cryogenic propellants for launch vehicle applications. The technology of subcooling cryogenic propellants below their normal boiling point to produce a denser fluid is one of the key process technologies necessary to meet the challenge of single-stage-to-orbit and reusable launch vehicles. Densified propellants are critical to lowering launch costs because they enable more propellant to be packed into a given unit volume, thus improving the performance by reducing the overall size and weight of the launch vehicle. This two-pronged research and test program has evolved into (1) conducting tank loading tests using densified liquid hydrogen and (2) developing two large-scale propellant densification systems that will be performance tested next year at Glenn. The propellant-loading test program was undertaken at Glenn in coordination with Lockheed Martin Michoud Space Systems. In this testing, the liquid hydrogen recirculation and densification process was simulated, and the thermal stratification of the densified propellant was recorded throughout the tank. The test article was a flight-weight tank constructed from composite materials similar to those to be used on the X-33 launch vehicle. The tank geometry as designed by Lockheed Martin had two cylindrical lobes with a center septum. Liquid hydrogen flow rate, pressure data, and temperature data plotted over time were collected while the subscale tank was filled with 27 R (15 K) densified liquid hydrogen propellant. This testing has validated mathematical models and demonstrated the readiness of densified propellant technology for near-term use. It marks the first time that such a process has been carried out with a multiple-lobe, flight-similar tank. Glenn researchers have also been working on providing a process and critical test data for the continuous production of densified liquid hydrogen (LH2) and densified liquid oxygen (LO2). Each densification production process uses a high-efficiency, subatmospheric boiling bath heat exchanger to cool the working fluid. A near triple-point hydrogen boiling bath is used to condition and subcool hydrogen to 27 R (15 K), and a nitrogen boiling bath is used to cool the liquid oxygen to 120 R (66.7 K). Multistage centrifugal compressors operating at cryogenic inlet conditions maintain the heat exchanger bath vapor pressure below 1 atm. The LO2 propellant densification unit shown in the photograph has a 30 lb/sec capacity, whereas the LH2 unit was designed to process 8 lb/sec of propellant. Each densification unit will be transported to Glenn's South Forty area after all fabrication work is completed sometime late next year. There the LO2 and LH2 densifier performance tests will be conducted with another larger Lockheed Martin tank designated the Structural Test Article (STA). This liquid oxygen tank is a full-scale, flight-weight, prototype aluminum tank designed for the X-33. It has a capacity of 20,000 gallons of LO2. The tank loading and recirculation testing planned for next year with STA will provide the data necessary for full-scale development of propellant densification technology.

Tomsik, Thomas M.↗

JPL field measurements at the Finney County, Kansas, test site, October 1976: Meteorological variables, surface reflectivity, surface and subsurface temperatures

Data collected at the Finney County, Kansas test site as part of the Joint Soil Moisture Experiment (JSME) are presented here, prior to analysis, to provide all JSME investigators with an immediate source of primary information. The ground-truth measurements were taken to verify and complement soil moisture data taken by microwave and infrared sensors during aircraft overflights. Measurements were made of meteorological variables (air speed, temperature, relative humidity, and rainfall), surface reflectivity, and temperatures at and below the surface.

Kahle, A. B.↗

Device and method for determining freezing points

A freezing point method and device (10) are disclosed. The method and device pertain to an inflection point technique for determining the freezing points of mixtures. In both the method and device (10), the mixture is cooled to a point below its anticipated freezing point and then warmed at a substantially linear rate. During the warming process, the rate of increase of temperature of the mixture is monitored by, for example, thermocouple (28) with the thermocouple output signal being amplified and differentiated by a differentiator (42). The rate of increase of temperature data are analyzed and a peak rate of increase of temperature is identified. In the preferred device (10) a computer (22) is utilized to analyze the rate of increase of temperature data following the warming process. Once the maximum rate of increase of temperature is identified, the corresponding temperature of the mixture is located and earmarked as being substantially equal to the freezing point of the mixture. In a preferred device (10), the computer (22), in addition to collecting the temperature and rate of change of temperature data, controls a programmable power supply (14) to provide a predetermined amount of cooling and warming current to thermoelectric modules (56).

Mathiprakasam, Balakrishnan↗