SEARCH · Search NASA

Results for “tensile behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Tensile and fatigue behavior of tungsten/copper composites

Work on W/Cu unidirectional composites was initiated to study the behavior of this ductile-ductile composite system under thermomechanical fatigue and to examine the applicability of fatigue-life prediction methods for thermomechanical fatigue of this metal matrix composite. The first step was to characterize the tensile behavior of four ply, 10 vol. percent W/Cu plates at room and elevated temperatures. Fatigue tests were conducted in load control on 0 degree specimens at 260 C. The maximum cyclic stress was varied but the minimum cyclic stress was kept constant. All tests were performed in vacuum. The strain at failure increased with increasing maximum cyclic stress.

Verrilli, Michael J.↗

NASA NTRS1993

Elastic-plastic finite element analyses of an unidirectional, 9 vol percent tungsten fiber reinforced copper matrix composite

Micromechanical modeling via elastic-plastic finite element analyses were performed to investigate the effects that the residual stresses and the degree of matrix work hardening (i.e., cold-worked, annealed) have upon the behavior of a 9 vol percent, unidirectional W/Cu composite, undergoing tensile loading. The inclusion of the residual stress-containing state as well as the simulated matrix material conditions proved to be significant since the Cu matrix material exhibited plastic deformation, which affected the subsequent tensile response of the composite system. The stresses generated during cooldown to room temperature from the manufacturing temperature were more of a factor on the annealed-matrix composite, since they induced the softened matrix to plastically flow. This event limited the total load-carrying capacity of this matrix-dominated, ductile-ductile type material system. Plastic deformation of the hardened-matrix composite during the thermal cooldown stage was not considerable, therefore, the composite was able to sustain a higher stress before showing any appreciable matrix plasticity. The predicted room temperature, stress-strain response, and deformation stages under both material conditions represented upper and lower bounds characteristic of the composite's tensile behavior. The initial deformation stage for the hardened material condition showed negligible matrix plastic deformation while for the annealed state, its initial deformation stage showed extensive matrix plasticity. Both material conditions exhibited a final deformation stage where the fiber and matrix were straining plastically. The predicted stress-strain results were compared to the experimental, room temperature, tensile stress-strain curve generated from this particular composite system. The analyses indicated that the actual thermal-mechanical state of the composite's Cu matrix, represented by the experimental data, followed the annealed material condition.

Sanfeliz, Jose G.↗

NASA NTRS2003

Microstructure and Mechanical Properties of Extruded Gamma Met PX

A gamma TiAl alloy with a high Nb content is being assessed as a compressor blade material. The microstructure and mechanical properties of extruded Ti-45Al-X(Nb,B,C) (at %) were evaluated in both an as-extruded condition and after a lamellar heat treatment. Tensile behavior of both as-extruded and lamellar heat treated specimens was studied in the temperature range of RT to 926 C. In general, the yield stress and ultimate tensile strength reached relatively high values at room temperature and decreased with increasing deformation temperature. The fatigue strength of both microstructures was characterized at 650 C and compared to a baseline TiAl alloy and to a Ni-base superalloy. Tensile and fatigue specimens were also exposed to 800 C for 200 h in air to evaluate the alloy's environmental resistance. A decrease in ductility was observed at room temperature due to the 800 C exposure but the 650 C fatigue properties were unaffected. Compressive and tensile creep testing between 727 and 1027 C revealed that the creep deformation was reproducible and predictable. Creep strengths reached superalloy-like levels at fast strain rates and lower temperatures but deformation at slower strain rates and/or higher temperature indicated significant weakening for the as-extruded condition. At high temperatures and low stresses, the lamellar microstructure had improved creep properties when compared to the as-extruded material. Microstructural evolution during heat treatment, identification of various phases, and the effect of microstructure on the tensile, fatigue, and creep behaviors is discussed.

Draper, S. L.↗

NASA NTRS2003

Microstructure and Mechanical Properties of Extruded Gamma Microstructure Met PX

A gamma TiAl alloy with a high Nb content is being assessed as a compressor blade material. The microstructure and mechanical properties of extruded Ti-45Al-X(Nb,B,C) (at.%) were evaluated in both an as-extruded condition and after a lamellar heat treatment. Tensile behavior of both as-extruded and lamellar heat treated specimens was studied in the temperature range of RT to 926 C. In general, the yield stress and ultimate tensile strength reached relatively high values at room temperature and decreased with increasing deformation temperature. The fatigue strength of both microstructures was characterized at 650 C and compared to a baseline TiAl alloy and to a Ni-base superalloy. Tensile and fatigue specimens were also exposed to 800 C for 200 h in air to evaluate the alloy's environmental resistance. A decrease in ductility was observed at room temperature due to the 800 C. exposure but the 650 C fatigue properties were unaffected. Compressive and tensile creep testing between 727 and 1027 C revealed that the creep deformation was reproducible and predictable. Creep strengths reached superalloy-like levels at fast strain rates and lower temperatures but deformation at slower strain rates and/or higher temperature indicated significant weakening for the as-extruded condition. At high temperatures and low stresses, the lamellar microstructure had improved creep properties when compared to the as-extruded material. Microstructural evolution during heat treatment, identification of various phases, and the effect of microstructure on the tensile, fatigue, and creep behaviors is discussed.

Draper, S. L.↗

NASA NTRS1991

Modeling of nonlinear constitutive relations of woven ceramic composites

The linear and nonlinear tensile behavior of SiC/SiC composites is examined. This analysis is based on the observed stress-strain behavior and damage evolution from a series of loading and unloading tensile tests. Stress distribution of the composite with transverse cracks in the transverse yarns is examined, and the nonlinearity of the composite stress-strain relation due to the presence of transverse cracks is predicted by application of a maximum failure strain criterion for the transverse yarn.

Kuo, Wen-Shyong↗

NASA NTRS1990

Tensile deformation of 2618 and Al-Fe-Si-V aluminum alloys at elevated temperatures

The present study experimentally characterizes the effects of elevated temperature on the uniaxial tensile behavior of ingot metallurgy 2618 Al alloy and the rapidly solidified FVS 0812 P/M alloy by means of two constitutive formulations: the Ramberg/Osgood equation and the Bodner-Partom (1975) incremental formulation for uniaxial tensile loading. The elastoplastic strain-hardening behavior of the ingot metallurgy alloy is equally well represented by either formulation. Both alloys deform similarly under decreasing load after only 1-5 percent uniform tensile strain, a response which is not described by either constitutive relation.

Leng, Y.↗

NASA NTRSDate not supplied

Multiscale Prediction of Yarn Pullout Failure Mode in Unreinforced Textile Fabrics

Unreinforced woven fabrics have been implemented in a variety of high performance applications, including body armor, deployable structures, and as the reinforcement material in composites. Multiscale modeling techniques have significantly improved the capabilities of simulation-based tools to capture fabric mechanics efficiently and accurately, but often lack in their prediction of failure and require pairing with finite element analysis (FEA) software, limiting their application to the design of ‘fit-for-purpose’ materials. NASA’s Multiscale Analysis Tool (NASMAT) is a standalone multiscale program that has been traditionally used in the analysis of reinforced composites materials. More recently, it has been amended to simulate unreinforced fabric behavior by allowing the geometric state of the tows to change with applied loading due to the lack of a reinforcement material, such as the matrix seen in composites. Previous work has shown the ability of NASMAT to capture nonlinear macroscale behavior by predicting geometric changes in the state of each subcell as a function of the applied loading and allowing each subcell in the analysis to rotate according to these predicted changes, as well as predict nonlinear behavior due to the fiber breakage failure mode. In this work, the capability of predicting the onset and propagation of failure in plain woven fabrics in NASMAT is presented for the yarn pullout failure mode, which occurs when a fabric is loaded at an off-axis angle relative to the warp of weft tow direction. Yarn pullout behavior is initiated by determining the applied load in which the shear resistance of the contact area between yarn families is overcome. When failure is initiated, yarn pullout is determined to have occurred when the applied displacement, calculated from global strain, exceeds the deformed position of a given contact points between yarn families, determined from pin-joint kinematics. Contact points where pullout has occurred contribute to a global damage parameter used to modify the homogenized stiffness of the fabric, resulting in nonlinear behavior observed at the macroscale. The off-axis loading behavior and yarn pullout failure theory have been developed and implemented into NASMAT such that users can simulate off-axis tensile behavior of fabrics in a single, standalone multiscale tool. Simulations are compared to uniaxial tensile tests at various off-axis angles to demonstrate the capability of the tool in its prediction of both the onset of failure at each off-axis angles and the stress-strain behavior as failure progresses.

Materials↗

NASA NTRSDate not supplied

Effect of Heat Treatments on the Tensile Properties of Additively Manufactured 15-5 Ph Stainless Steel

This study investigated the effect of post-manufacture heat treatments on the microstructure and mechanical properties of 15-5 PH stainless steel (SS) fabricated by laser powder-directed energy deposition (LP-DED). Various heat treatment procedures (CA-H900 and CA-H1150) were conducted to evaluate their effects on the tensile behavior of LP-DED 15-5 PH SS. Scanning electron microscopy was used to characterize the microstructural features and the fracture surfaces. Tensile tests were performed to evaluate the mechanical properties at cryogenic and room temperatures. Reduction in area of CA-H1150 treated specimens after tensile tests was significantly higher than CA-H900 ones, while the ultimate tensile and yield strengths of CA-H900 specimens were higher compared to the CA-H1150 ones. The mechanical behavior of the LP-DED 15-5 PH SS in various heat treatment conditions is discussed based on their microstructures and fracture surfaces.

Laser powder directed energy deposition (LP-DED)↗

NASA NTRS1975

Fracture mechanics correlation of boron/aluminum coupons containing stress risers

The mechanical behavior of boron/aluminum near stress risers has been studied and reported. This effort was directed toward defining the tensile behavior of both unidirectional and (0/ plus or minus 45) boron/aluminum using linear elastic fracture mechanics (LEFM). The material used was 5.6-mil boron in 6061 aluminum, consolidated using conventional diffusion bonding techniques. Mechanical properties are reported for both unidirectional and (0/ plus or minus 45) boron/aluminum, which serve as control data for the fracture mechanics predictions. Three different flawed specimen types were studied. In each case the series of specimens remained geometrically similar to eliminate variations in finite size correction factors. The fracture data from these tests were reduced using two techniques. They both used conventional LEFM methods, but the existence of a characteristic flaw was assumed in one case and not the other. Both the data and the physical behavior of the specimens support the characteristic flaw hypothesis. Cracks were observed growing slowly in the (0/ plus or minus 45) laminates, until a critical crack length was reached at which time catastrophic failure occurred.

Adsit, N. R.↗

DOE OSTI2020

Sodium Exposure Tests of A709 Steel (FY2020 Progress Report)

Sodium exposure tests were conducted on the first commercial heat, H58776 of A709 steel. Six different processing and heat treatment conditions were investigated, including three processing conditions, namely, Argon-Oxygen-Decarburization (AOD), Electro-slag Remelting (ESR), and Electro-slag Remelting with subsequent homogenization (HOMO), and two heat treatment conditions, i.e. solution annealing at 1100°C (SA1100°C) or 1150°C (SA1150°C). Specimens of AOD-SA1100°C, AOD-SA1150°C, ESR-SA1100°C, ESR-SA1150°C, HOMO-SA1100°C, and HOMO-SA1150°C were tested in sodium at 650°C and for times up to 10,152 h. Specimens in the AOD-SA1100°C and AOD-SA1150°C conditions were also tested in sodium at 550 and 600°C. Parallel thermal aging experiments were carried out for comparison with sodium exposure tests to separate the thermal and sodium effects. It was found that A709 H58776 generally showed a weight loss after sodium exposures at 650°C except a few data points of the ESR-SA1100°C specimens. The corrosion rate showed large variations in the initial stage and decreased with increasing exposure time. Long-term exposure tests are needed to determine its steady-state corrosion rate. The AOD-SA1100°C and HOMO-SA1100°C specimens showed similar tensile responses after thermal or sodium exposures at 650°C. The yield stress increased, the ultimate tensile strength decreased, and the uniform and total elongations were reduced after thermal or sodium exposures. A longer exposure time had a minimal effect on the tensile strength but further reduced the tensile ductility. The sodium-exposed specimens had higher tensile strength than the thermally-aged specimens. In contrast, the ESR-SA1100°C specimens showed an increase in the yield stress and the ultimate tensile strength after thermal or sodium exposures at 650°C and ~10,000 h. The AOD-SA1150°C and ESR-SA1150°C specimens showed similar tensile behavior after thermal or sodium exposures at 650°C.Thermal or sodium exposures at 650°C increased the yield stress, decreased the ultimate tensile strength, and reduced uniform and total elongations. There were minimal differences in tensile properties between the sodium-exposed and thermally-aged specimens after an ~3000 h exposure. After an exposure for ~10,000 h the sodium-exposed specimens showed higher yield stress and ultimate tensile strength and lower uniform and total elongations than the thermally-aged specimens. For the HOMO-SA1150°C specimens, thermal or sodium exposures at 650°C significantly increased the yield stress but had a minimal effect on the ultimate tensile strength. Both uniform and total elongations were significantly reduced at an exposure time of ~3,000 h, and they were further reduced after an exposure of ~10,000 h. The sodium-exposed specimens had lower tensile ductility than the thermally-aged specimens. Before exposure, the stress-strain curves of the specimens in all six processing-heat treatment conditions showed serrations indicating the dynamic aging effect at 650°C. Thermal aging or sodium exposures at 650°C after ~10,000 h completely removed the serrations of the flow curves in A709 H58776, indicating strong precipitation during thermal or sodium exposures. Longer-term sodium exposure tests are needed to determine the steady-state corrosion rates in sodium for A709 H58776 and fully understand the influence of sodium exposures on its mechanical performance.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Microstructural heterogeneities in additively manufactured refractory alloy C103 and their implications for room and elevated temperature mechanical behavior

Considering the vast component design space enabled by fusion-based additive manufacturing (F-BAM) processes, e.g., directed energy deposition (DED), the scale-up manufacturing of Nb-alloys with F-BAM is advantageous for structural applications. However, varying thermokinetic parameters-induced microstructural heterogeneities are prevalent within the F-BAM processed alloys. Such microstructural heterogeneities can have significant implications for the room and elevated temperature mechanical behavior. While a few studies investigating F-BAM processed alloy C103 are available, none of these studies investigate the microstructural heterogeneities – including those associated with solidification growth modes and second phase particles – and the effect thereof on the mechanical behavior. To this end, we investigate the microstructurally heterogeneous regions with varying solidification growth morphologies, segregation behavior, and second phase particle attributes within the laser-DED processed alloy C103. The implications of such heterogeneous regions for room- and elevated-temperature tensile behavior and damage mechanisms are revealed. Particularly, the interface between the cellular and planar region is identified as susceptible to deformation localization. The implications of hot isostatic pressing (HIP) for the consolidation behavior, microstructural evolution, and resulting mechanical behavior are also discussed. Although the recrystallization and grain growth led to a reduced yield strength in the HIPed condition, the homogenization of microstructure alleviated the deformation localization sites, such as the planar/cellular interface within the melt pool. The homogenized microstructure alongside the enhanced consolidation upon HIP led to an enhanced elongation to failure. Findings establish microstructural design considerations in F-BAM processed Nb alloys and also facilitate design of post-processing heat treatments for achieving improved mechanical properties.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Tensile strain-rate sensitivity of tungsten/niobium composites at 1300 to 1600 K

The tensile behavior of continuous tungsten fiber reinforced niobium composites (W/Nb), fabricated by an arc-spray process, was studied in the 1300 to 1600 K temperature range. The tensile properties of the fiber and matrix components as well as of the composites were measured and were compared to rule of mixtures (ROM) predictions. The deviation from the ROM was found to depend upon the chemistry of the tungsten alloy fibers, with positive deviations for ST300/Nb (i.e., stronger composite strength than the ROM) and negative or zero deviations for 218/Nb.

Yun, H. M.↗

DOE OSTI2022

Effect of processing parameters and build orientation on microstructure and performance of AISI stainless steel 304L made with selective laser melting under different strain rates

Selective laser melting (SLM) process brings diverse potentials on geometry flexibility; therefore, it is more and more widespread to be employed in fabrication metal alloys served for industries. Nonetheless, a material characterization study is desired to carry on for better understanding the correlation among process, structure, microstructure, and performance. In the current study, the SLM fabricated AISI stainless steel 304L was fabricated with different process parameters and built orientations (horizontal, inclined, and vertical. The tensile behavior was evaluated under different strain rates (0.0001 /s, 0.001 /s, 0.01 /s, and 0.1 /s) and compared to the commercial cold-rolled and annealed counterpart. Grain structures, tensile strength, elongation-to-failure, strain rate sensitivity, work hardening, and fractographic analysis were evaluated in terms of the effect of energy density, build orientation, and strain rate. The output indicates the tensile strength increases with increasing strain rates. On the contrary, the elongation-to-failure shows a decreasing trend with strain rates. Tensile properties of specimens built in the horizontal and inclined orientations are more sensitive to strain rates due to the smaller dimension of grain structures. Tensile anisotropy depends on the energy input, where a high energy density could yield a strong build orientation-dependent anisotropy. Hall-Petch relationship is validated to explain the mechanical anisotropy in different built orientations for SLM alloys. The strain hardening exponent and work hardening rate are demonstrated to be positively correlated, and they increase with smaller grain sizes. The fine dimple features indicate the ductile fracture mode regardless of strain rates. The size of the ductile dimples seems to depend on the strain rates and build orientations.

36 MATERIALS SCIENCE↗

NASA NTRS2001

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗

NASA NTRS1972

Void growth in an elastic-plastic medium.

The uniaxial deformation of an elastic-plastic medium containing a doubly periodic square array of circular cylindrical voids is studied under plane-strain conditions. Both the effects of geometrical nonlinearities resulting from large deformation and physical nonlinearities arising from plastic material behavior are included in formulating the problem. A variational principle is used as the basis for implementing a finite-element solution. Results are obtained for the change in void shape and size under increasing overall strain, the overall tensile behavior of the material with voids, and the development of the plastic zone about a void.

Needleman, A.↗

DOE OSTI2020

Relationship between ductility and the porosity of additively manufactured AlSi10Mg

Additive manufacturing via selective laser melting can result in variable levels of internal porosity both between build plates and within components from the same build. In this work, sample porosity levels were compared to tensile properties for 176 samples spanning eight different build plates. Sample porosity was measured both by Archimedes density, which provided an estimation of overall porosity, and by observation of voids in the fracture surface, which provided an estimation of the porosity at the failure plane. The porosity observed at the fracture surface consistently demonstrated higher porosity than that suggested by Archimedes density. The porosity values obtained from both methods were compared against the mechanical results. Sample porosity appears to have some correlation to the ultimate tensile strength, yield strength, and modulus, but the strongest relationship is observed between porosity and ductility. Three different models were used to relate the fracture surface porosity to the ductility. The first method was a simple linear regression analysis, while the other two models have been used to relate porosity to ductility in cast alloys. It is shown that all three models fit the data well over the observed porosity ranges, suggesting that the models taken from casting theory can extend to additively manufactured metals. Finally, it is proposed that the non-destructive Archimedes method could be used to estimate an approximate sample ductility through the use of correlations realized here. Such a relationship could prove useful for design and for a deeper understanding of the impact of pores on tensile behavior.

36 MATERIALS SCIENCE↗

NASA NTRS1977

The influence of growth speed, orientation and environment on fracture of aligned Al-CuAl2

There has been considerable interest in the mechanical properties of aligned eutectics as functions of microstructure, orientation between reinforcement and stress axis, and temperature of testing. However, little is known about the behavior of these alloys in aggressive environments, such as liquid metals, with the exception of a recent paper on embrittlement of several eutectic alloys in gallium and gallium-indium alloys. This paper is concerned with the effects of a liquid Ga-16%In solution on tensile behavior of an aligned Al-CuAl2 eutectic.

Skiff, P. K.↗

NASA NTRS1974

Reinforcement of metals with advanced filamentary composites

This paper reviews some recent applications of the concept of reinforcing metal structures with advanced filamentary composites, and presents some results of an experimental investigation of the tensile behavior of aluminum and titanium reinforced with unidirectional boron/epoxy. Results are given for tubular and flat specimens, bonded at either room temperature or elevated temperature. The composite reinforced metals showed increased stiffness over the all-metal counterpart, as predicted by the rule of mixtures, and the results were independent of specimen geometry. The tensile strength of the born/epoxy reinforced metals is shown to be a function of the geometry of the test specimen and the method of bonding the composite to the metal.

Herakovich, C. T.↗