Results for “thermoplastic reinforcement” — Page 5

DOE OSTI2022

A review of the fabrication methods and mechanical behavior of continuous thermoplastic polymer fiber–thermoplastic polymer matrix composites

Abstract Thermoplastic polymer fiber–thermoplastic polymer matrix composites (PPCs or PRFPs), often recognized as self‐reinforced or single polymer composites, are potential candidates for future advanced polymer composites because of various advantages ( e.g., recyclability, formability, low‐cost, ultra‐lightweight, environmental friendliness, etc.). The manufacturability and mechanical behavior of these composites compared to conventional carbon‐/glass‐/aramid‐fiber‐reinforced polymers is of great interest to the composites community, but there are a limited number of studies in this area. To this end, this paper reviewed fabrication methods with different processing parameters and mechanical behavior of uni‐/multi‐directional thermoplastic PPCs featuring continuous thermoplastic polymer fibers from limited data in the literature. It was shown that most specific behaviors (normalized by density) of these materials in various loading conditions (e.g., quasi‐static tension/shear/flexure, tension‐tension fatigue, and out‐of‐plane impacting, etc.) are comparable to or better than glass‐/aramid‐fiber‐reinforced polymers. Particularly, the specific ductility in the foregoing conditions outperforms all the carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Thermoplastic PPCs with remarkable performance can be achieved through several uncomplicated methods (e.g., film stacking, hot compaction, powder and solution impregnations, matrix infusion and injection molding, additive manufacturing, etc.), which have some similarities to the methods used for carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Moreover, several opportunities and challenging problems of thermoplastic PPCs were summarized at the end of this review paper. Efficient solutions may require countless efforts in the composites community to further strengthen the performance and understanding of thermoplastic PPCs for wide applications in various engineering fields in the future.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Dynamic behavior of reversible oxygen migration in irradiated-annealed high temperature superconducting wires

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Post-process annealing of large-scale 3D printed polyphenylene sulfide composites

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗

NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗

NASA NTRS1991

An improved compression molding technology for continuous fiber reinforced composite laminate. Part 1: AS-4/LaRC-TPI 1500 (HFG) Prepreg system

Poor processability of fiber reinforced high performance polyimide thermoplastic resin composites is a well recognized issue which, in many cases, prohibits the fabrication of composite parts with satisfactorily consolidated quality. Without modifying the resin matrix chemistry, improved compression modeling procedures were proposed and investigated with the AS-4/LaRC-TPI 1500 High Flow Grade (HFG) prepreg system. Composite panels with excellent C-scans can be consistently molded by this method under 700 F and a consolidation pressure as low as 100 psi. A mechanism for the consolidation of the composite under this improved molding technique is discussed. This mechanism reveals that a certain degree of matrix shear and tow filament slippage and nesting between plies occur during consolidation, which leads to a reduction of the consolidating pressure necessary to offset the otherwise intimate inter fiber-fiber contact and consequently achieves a better consolidation quality. Outstanding short beam shear strength and flexural strength were obtained from the molded panels. A prolonged consolidation step under low pressure, i.e., 100 psi at 700 F for 75 minutes, was found to significantly enhance the composite mechanical properties.

Hou, Tan-Hung↗

NASA NTRS1994

Society of the plastic industry process emission initiatives

At first view, plastics process emissions research may not seem to have much bearing on outgassing considerations relative to advanced composite materials; however, several parallel issues and cross currents are of mutual interest. The following topics are discussed: relevance of plastics industry research to aerospace composites; impact of clean air act amendment requirements; scope of the Society of the Plastics Industry, Inc. activities in thermoplastic process emissions and reinforced plastics/composites process emissions; and utility of SPI research for advanced polymer composites audiences.

Mcdermott, Joseph↗

NASA NTRS2003

Dry Process for Making Polyimide/ Carbon-and-Boron-Fiber Tape

A dry process has been invented as an improved means of manufacturing composite prepreg tapes that consist of high-temperature thermoplastic polyimide resin matrices reinforced with carbon and boron fibers. Such tapes are used (especially in the aircraft industry) to fabricate strong, lightweight composite-material structural components. The inclusion of boron fibers results in compression strengths greater than can be achieved by use of carbon fibers alone. The present dry process is intended to enable the manufacture of prepreg tapes (1) that contain little or no solvent; (2) that have the desired dimensions, fiber areal weight, and resin content; and (3) in which all of the fibers are adequately wetted by resin and the boron fibers are fully encapsulated and evenly dispersed. Prepreg tapes must have these properties to be useable in the manufacture of high-quality composites by automated tape placement. The elimination of solvent and the use of automated tape placement would reduce the overall costs of manufacturing.

Belvin, Harry L.↗

DOE OSTI2024

Hygrothermal aging and recycling effects on mechanical and thermal properties of recyclable thermoplastic glass fiber composites

Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.

17 WIND ENERGY↗

NASA NTRSDate not supplied

Evaluating Crystallinity in Thermoplastic composites

Polymer matrix composites (PMCs) offer many benefits for the aerospace industry due to their potential for weight reduction when compared to metal or ceramic based materials. Most PMCs currently in flight use thermoset matrices, however, thermoplastic resins are being explored as alternatives due to their ability to be remelted, which is of particular interest due to the potential for in-situ repair and manufacturing required in space. Most thermoplastic resins are semicrystalline polymers. The properties of semicrystalline thermoplastics are largely influenced by their crystallinity, which can vary due to many factors including thermal treatments, environmental conditions, and mechanical deformation. Monitoring the crystallinity of thermoplastic composites is key to ensuring these materials reliably meet the high demands required by space exploration. This talk discusses the use of multiple techniques such as Polarized Light Optical Microscopy and Fourier-Transform Infrared Spectroscopy to characterize the crystallinity in various thermoplastic composites, including carbon fiber reinforced PMCs and novel bio-based Martian and Lunar regolith composites designed for in-situ manufacturing. This work aims to provide the fundamental data necessary to understand the effects of crystallinity on thermoplastic PMCs, which is key to advancing their use in space applications.

Thermoplastics↗

DOE OSTI2025

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗

NASA NTRS1984

Thermoplastic-carbon fiber hybrid yarn

Efforts were directed to develop processing methods to make carbon fiber/thermoplastic fiber preforms that are easy to handle and drapeable, and to consolidate them into low void content laminates. The objectives were attained with the development of the hybrid yarn concept; whereby, thermoplastic fiber can be intimately intermixed with carbon fiber into a hybrid yarn. This was demonstrated with the intermixing of Celion 3000 with a Celanese liquid crystal polymer fiber, polybutylene terepthalate fiber, or polyetheretherketone fiber. The intermixing of the thermoplastic matrix fiber and the reinforcing carbon fiber gives a preform that can be easily fabricated into laminates with low void content. Mechanical properties of the laminates were not optimized; however, initial results indicated properties typical of a thermoplastic/carbon fiber composites prepared by more conventional methods.

Ketterer, M. E.↗

NASA NTRS1986

International SAMPE Symposium and Exhibition, 31st, Los Angeles, CA, April 7-10, 1986, Proceedings

The present conference on the development status of advanced structural materials considers topics arising in such areas as automated structural manufacturing, advanced material and structure design techniques, environmental effects on materials, composite matrix processing, computer modeling for materials and processes, materials development trends in Europe and in Japan, fiber and whisker reinforcement development status, and novel thermoplastic materials and their applications. Also discussed are pressure-sensitive adhesive systems, materials suitable for space applications, polyimide resin systems, electronic materials, novel resin chemistries, ceramic and metallic systems, and the impact performance of state-of-the-art materials.

Bauer, J. L.↗

DOE OSTI2022

Methane Pyrolysis for CO2-free H2 and Carbon Nanomaterials (Abstract)

We propose to continue to develop a new process for producing CO2-free hydrogen (H2) from inexpensive and domestically-abundant natural gas (NG), while simultaneously reducing H2’s net production cost to $1.0/kg through the sale of valuable crystalline solid carbon co-product. Producing clean hydrogen at this price is a DOE Hydrogen Energy Earthshot goal. Cost effective production of clean H2 is also of commercial relevance to project partners Southern California Gas Company (SoCalGas) and startup company C4-MCP, who aim to further develop, demonstrate at scale, and ultimately deploy the new process technology developed on this project in order to meet regulatory demands in the State of California. In the current project we have focused on i) understanding the catalyst science for thermocatalytic decomposition of methane (TCD), which resulted in the development of a patent pending bimetallic catalyst offering favorable activity, stability, and selectivity under industrially relevant process conditions, ii) developing a novel, patent pending process to enable the separation of produced carbon and catalyst, and re-synthesis of the catalyst using recycled materials, iii) performing limited characterization of the produced carbon materials, and iv) performing detailed process modeling in order to perform techno economic assessment. The additional scope proposed here will accelerate the commercial deployment of TCD for CO2-free H2 and valuable solid carbon nanotubes (CNT) co-product, by i) scaling up the production of CNT co-product using a scalable, fluidized bed reactor (25 g catalyst scale versus the 1 g catalyst scale demonstrated to-date), ii) producing at least 40 g of CNT product, produced via multiple cycles of TCD, carbon-catalyst separation, and catalyst re-synthesis, to enable the production of sufficient quantities of solid carbon so as to explore its market potential, iii) understanding the quality of the co-product CNTs, produced at larger scale, through advanced characterization, and iv) beginning to explore multiple promising high volume carbon product applications (thermoplastics, automotive composites, battery, and cement reinforcement applications).

08 HYDROGEN↗

DOE OSTI2024

Evaluation of Dissolvable Additively Manufactured Molds and Supports for Electroimpacts Innovative Additive Manufacturing Process

Electroimpact inc. has developed a new additive manufacturing process involving continuous fiber reinforcement along with high-strength thermoplastics. A unique part of this process includes using additive manufacturing to print a base geometry that is then used as a tool for continuous fiber placement. Ideally the tool should be disposable and cost effective. After printing the base tool, continuous fiber is printed on top of the tool using a secondary additive head on the same system to create the final printed part. After continuous fiber printing is completed, the tool is removed and disposed of to leave only the final desired structure. Materials used for the base tool have several requirements that must be met in order to complete this process. First, the material must be rigid and strong enough to support the loads from the secondary printing operation (continuous fiber printing). In addition, the material must be able to adhere to the secondary process material as well be capable of being removed such that the only remaining structure is continuous fiber composite. Using innovative soluble materials allows for parts to be produced through additive with molds that are produced as non-reusable one-off shapes and sizes.

36 MATERIALS SCIENCE↗

NASA NTRS1985

Constituent Materials

This project is concerned with the study of polymer liquid crystals and oriented semicrystalline high-temperature thermoplastics in high modulus carbon fiber reinforced composites. Emphasis is being placed on the determination of the effects of polymer orientation at the fiber surfaces on composite fracture and mechanical properties.

Source record↗

NASA NTRS1992

Polymer matrix composites on LDEF experiments M0003-9 and M0003-10

Over 250 polymer matrix composites were exposed to the natural space environment on Long Duration Exposure Facility (LDEF) experiments M0003-9 and 10. The experiments included a wide variety of epoxy, thermoplastic, polyimide, and bismalimide matrix composites reinforced with graphite, glass, or organic fibers. A review of the significant observations and test results obtained to date is presented. Estimated recession depths from atomic oxygen exposure are reported and the resulting surface morphologies are discussed. The effects of the LDEF exposure on the flexural strength and modulus, short beam shear strength, and coefficient of thermal expansion of several classes of bare and coated composites are reviewed. Lap shear data are presented for composite-to-composite and composite-to-aluminum alloy samples that were prepared using different bonding techniques and subsequently flown on LDEF.

Steckel, Gary L.↗

DOE OSTI2021

Devices and methods for additive manufacturing using flexible filaments

A method of fabricating (printing) parts utilizing flexible filaments includes anchoring a portion of a flexible filament to a substrate. A length of flexible filament is extended over the substrate while the flexible filament is in tension to thereby avoid buckling of the flexible filament. The flexible filament may comprise a thermoplastic material and fibers or other reinforcing materials whereby composite 3D parts can be fabricated.

Gardner, John M.↗