Search NASA⌕ Search

SEARCH · Search NASA

Results for “transpiration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Monte Carlo analysis of lobular gas-surface scattering in tubes applied to thermal transpiration

A model of rarefied gas flow in tubes was developed which combines a lobular distribution with diffuse reflection at the wall. The model with Monte Carlo techniques was used to explain previously observed deviations in the free molecular thermal transpiration ratio which suggest molecules can have a greater tube transmission probability in a hot-to-cold direction than in a cold-to-hot direction. The model yields correct magnitudes of transmission probability ratios for helium in Pyrex tubing (1.09 to 1.14), and some effects of wall-temperature distribution, tube surface roughness, tube dimensions, gas temperature, and gas molecular mass.

Smith, J. D.↗
NASA NTRS1971

Transpiration and film cooling boundary layer computer program. Volume 1: Numerical solutions of the turbulent boundary layer equations with equilibrium chemistry

A finite difference turbulent boundary layer computer program has been developed. The program is primarily oriented towards the calculation of boundary layer performance losses in rocket engines; however, the solution is general, and has much broader applicability. The effects of transpiration and film cooling as well as the effect of equilibrium chemical reactions (currently restricted to the H2-O2 system) can be calculated. The turbulent transport terms are evaluated using the phenomenological mixing length - eddy viscosity concept. The equations of motion are solved using the Crank-Nicolson implicit finite difference technique. The analysis and computer program have been checked out by solving a series of both laminar and turbulent test cases and comparing the results to data or other solutions. These comparisons have shown that the program is capable of producing very satisfactory results for a wide range of flows. Further refinements to the analysis and program, especially as applied to film cooling solutions, would be aided by the acquisition of a firm data base.

Levine, J. N.↗
NASA NTRS1972

Oxidation resistant porous material for transpiration cooled vanes

Porous metal sheet with controlled permeability was made by space winding and diffusion bonding fine wire. Two iron-chromium-aluminum alloys and three-chromium alloys were used: GE 1541 (Fe-Cr-Al-Y), H 875 (Fe-Cr-Al-Si), TD Ni Cr, DH 245 (Ni-Cr-Al-Si) and DH 242 (Ni-Cr-Si-Cb). GE 1541 and H 875 were shown in initial tests to have greater oxidation resistance than the other candidate alloys and were therefore tested more extensively. These two materials were cyclic furnace oxidation tested in air at 1800 and 2000 F for accumulated exposure times of 4, 16, 64, 100, 200, 300, 400, 500, and and 600 hours. Oxidation weight gain, permeability change and mechanical properties were determined after exposure. Metallographic examination was performed to determine effects of exposure on the porous metal and electron beam weld joints of porous sheet to IN 100 strut material. Hundred hour stress rupture life and tensile tests were performed at 1800 F. Both alloys had excellent oxidation resistance and retention of mechanical properties and appear suitable for use as transpiration cooling materials in high temperature gas turbine engines.

Madsen, P.↗
NASA NTRS1972

Gas crossflow effects on airflow through a wire-form transpiration cooling material

An experimental analysis was conducted to determine the effects of gas stream flow parallel to the discharging surface on the flow characteristics of a wire-form porous material. Flow data were obtained over a range of transpiration airflow rates from 0.129 to 0.695/grams per second-centimeter squared and external gas stream Mach numbers from 0 to 0.46. The conclusion was drawn that the flow characteristics of the wire cloth were not significantly affected by the external gas flows.

Kaufman, A. S.↗
NASA NTRS1973

Flow through a wire-form transpiration-cooled vane

Results of recent research to develop techniques for analyzing coolant flow in transpiration-cooled vanes are summarized. Flow characteristics of the wire-form porous material are correlated; the effects on the flow characteristics of oxidation, coolant temperature, gas crossflow, and airfoil curvature are evaluated. An analytical method is presented for predicting coolant flows and pressures in a strut-supported vane.

Kaufman, A. S.↗
NASA NTRS1973

Analysis of a water table simulation of a transpirationally cooled nozzle

Two flow models were formulated: for a no-mixing and a complete-mixing boundary layer. The approach taken assumes inviscid flow and constant pressure in the transverse direction. The models are simple enough so that extending them to apply to a gas nozzle, including heat transfer and density differences, should be possible. Both models predict experimental photographic data with similar results; but inherent two dimensional and parallax errors preclude choice of the best model. In general, the boundary layer thickens rapidly near the start of injection because of low acceleration forces; it thins near the throat because of high acceleration forces. The transpiration fluid increases the radius of curvature near the throat and decreases the divergence angle of the free flow downstream of the throat.

Kascak, A. F.↗
NASA NTRS1973

Fundamental study of transpiration cooling

Isothermal and non-isothermal pressure drop data and heat transfer data generated on porous 304L stainless steel wire forms, sintered spherical stainless steel powder, and sintered spherical OFHC copper powder are reported and correlated. Pressure drop data was collected over a temperature range from 500 R to 2000 R and heat transfer data collected over a heat flux range from 5 to 15 BTU/in2/sec. It was found that flow data could be correlated independently of transpirant temperature and type (i.e., H2, N2). It was also found that no simple relation between heat transfer coefficient and specimen porosity was obtainable.

Koh, J. C. Y.↗
NASA NTRS1976

A simplified analytical solution for thermal response of a one-dimensional, steady state transpiration cooling system in radiative and convective environment

A simplified analytical method for calculation of thermal response within a transpiration-cooled porous heat shield material in an intense radiative-convective heating environment is presented. The essential assumptions of the radiative and convective transfer processes in the heat shield matrix are the two-temperature approximation and the specified radiative-convective heatings of the front surface. Sample calculations for porous silica with CO2 injection are presented for some typical parameters of mass injection rate, porosity, and material thickness. The effect of these parameters on the cooling system is discussed.

Kubota, H.↗
NASA NTRS1985

Small gas turbine combustor study: Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗
NASA NTRS1985

Small gas turbine combustor study - Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗