Search NASA⌕ Search

SEARCH · Search NASA

Results for “transport control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Dynamic control of molecular transport MXene transistor membranes

Controlled spatial confinement and surface properties of lamellar 2D nanomaterial membranes could enhance many precision separation processes. Traditionally, researchers view channel dimensions, surface properties, and permeation rates of these membranes as intrinsic properties that cannot be modulated in operando. We report that gate voltage applied to the conducting laminar MXene membrane can modulate the permeation rate of ions and neutral solutes, as well as its effective size rejection. In operando wide-angle x-ray scattering measurements reveal that these changes are not driven by electrically induced variations in the d spacing of the MXene layers. Instead, experimental data and continuum electrokinetic modeling reveal that ion transport through the MXene channels is primarily affected by Donnan equilibrium at the membrane-solution interface. We also report a strong increase in the permeation rates through the membrane under a low-frequency ac voltage gating regime that we attribute to diffusioosmotic flow oscillations induced in the membrane. Overall, MXene “transistor” membranes provide a previously unidentified approach to dynamic control of molecular separations.

Pendse, Aaditya [Lawrence Livermore National Labor↗
DOE OSTI2020

Nucleation and Growth of PbBrF Crystals at the Liquid Mercury–Electrolyte Interface Studied by Operando X-ray Scattering

In this work, detailed in operando studies of electrochemically induced PbBrF deposition at the liquid mercury/liquid electrolyte interface are presented. The nucleation and growth were monitored using time-resolved X-ray diffraction and reflectivity combined with electrochemical measurements, revealing a complex potential-dependent behavior. PbBrF deposition commences at potentials above –0.7 V with the rapid formation of an ultrathin adlayer of one unit cell thickness, on top of which (001)-oriented three-dimensional crystallites are formed. Two potential regimes are identified. At low overpotentials, slow growth of a low surface density film of large crystals is observed. At high overpotentials, crossover to a potential-independent morphology occurs, consisting of a compact PbBrF deposit with a saturation thickness of 25 nm, which forms within a few minutes. This potential behavior can be rationalized by the increasing supersaturation near the interface, caused by the potential-dependent Pb2+ deamalgamation, which changes from a slow reaction-controlled process to a fast transport-controlled process in this range of overpotentials. In addition, growth on the liquid substrate is found to involve complex micromechanical effects, such as crystal reorientation and film breakup during dissolution.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Application of active controls to civil transport aircraft

The impact of active controls on civil transport aircraft and some of the complex problems involved are described. The approach taken by NASA as part of the Active Control Technology Program is discussed to integrate active controls in the conceptual design phase. It is shown that when handled correctly, active controls improve aircraft performance.

Taylor, L. W., Jr.↗
NASA NTRS1978

Simulator evaluation of a flight-path-angle control system for a transport airplane with direct lift control

A piloted simulator was used to evaluate the flight path angle control capabilities of a system that employs spoiler direct lift control. The system was designated the velocity vector control system and was compared with a baseline flight path angle control system which used elevator for control. The simulated airplane was a medium jet transport. Research pilots flew a manual instrument landing system glide slope tracking task and a variable flight path angle task in the landing configuration to obtain comparative performance data.

Kelley, W. W.↗
DOE OSTI2023

Use of intrinsic hysteresis for the active control of internal transport barriers in magnetically confined fusion plasmas

In magnetically confined fusion devices, control of internal transport barriers (ITBs) is important both to enhance and suppress the turbulent transport to improve confinement control. Barrier control should allow for the improvement of confinement to aid in achieving the needed fusion criteria while also permitting the degradation of confinement to control profiles and clean the device by moving out the impurities accumulated near the core. In this work, we present a novel control scenario that takes advantage of the hysteresis intrinsic to transport barriers to easily cycle through enhanced and degraded confinement regimes. The control scenario is illustrated using a five-field simplified transport model for an ITB using typical parameters of a neutral beam injection-heated DIII-D tokamak discharge. Pellets and ion cyclotron resonance frequency power are used as control knobs for this active control scenario. These knobs adequately modify at will the local gradients and, therefore, the growth rates and shearing rates, allowing for easy and efficient control of the barrier by taking advantage of the barrier hysteresis. The result is a control cycle that could be operated with a relatively small amount of power in high performance regimes which, nowadays, typically require large power to control. It may also have advantages to avoid, or at least ameliorate, the appearance of magnetohydrodynamic instabilities in the barrier region.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1997

A Rationale for System-Dependent Advantages and Disadvantages of Solution Crystal Growth at Low Gravity

Protein crystallization experiments at reduced gravity have yielded crystals that, depending on the specific material, are either superior or inferior in their structural perfection compared to counterparts grown at normal gravity. A reduction of the crystals' quality due to their growth at low gravity cannot be understood from existing models. Our experimental investigations of the ground-based crystallization of the protein lysozyme have revealed pronounced unsteady growth layer dynamics and associated defect formation under steady external conditions. Through scaling analysis and numerical simulations we show that the observed fluctuations originate from the coupling of bulk transport with non-linear interface kinetics under mixed kinetics-transport control of the growth rate. The amplitude of the fluctuations is smallest when either transport or interfacial kinetics dominate the control of the crystallization process. Thus, depending on the specific system, crystal quality may be improved by either enhancing or suppressing the transport in the solution. These considerations provide, for the first time, a material-dependent rationale for the advantages, as well as the disadvantages, of reduced gravity for (protein) crystallization.

Rosenberger, Franz↗
DOE OSTI2022

Efficient Intermolecular Charge Transport in π-Stacked Pyridinium Dimers Using Cucurbit[8]uril Supramolecular Complexes

Intermolecular charge transport through π-conjugated molecules plays an essential role in biochemical redox processes and energy storage applications. In this work, we observe highly efficient intermolecular charge transport upon dimerization of pyridinium molecules in the cavity of a synthetic host (cucurbit[8]uril, CB[8]). Stable, homoternary complexes are formed between pyridinium molecules and CB[8] with high binding affinity, resulting in an offset stacked geometry of two pyridiniums inside the host cavity. The charge transport properties of free and dimerized pyridiniums are characterized using a scanning tunneling microscope-break junction (STM-BJ) technique. Our results show that π-stacked pyridinium dimers exhibit comparable molecular conductance to isolated, single pyridinium molecules, despite a longer transport pathway and a switch from intra- to intermolecular charge transport. Control experiments using a CB[8] homologue (cucurbit[7]uril, CB[7]) show that the synthetic host primarily serves to facilitate dimer formation and plays a minimal role on molecular conductance. Molecular modeling using density functional theory (DFT) reveals that pyridinium molecules are planarized upon dimerization inside the host cavity, which facilitates charge transport. In addition, the π-stacked pyridinium dimers possess large intermolecular LUMO–LUMO couplings, leading to enhanced intermolecular charge transport. Altogether, this work demonstrates that supramolecular assembly can be used to control intermolecular charge transport in π-stacked molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Alkaline Zinc Passivation Mechanism is Controlled by Hydroxide Concentration

We studied Zn passivation and oxide growth in Zincate (Zn(OH) 4 2− ) in 4 and 8 M KOH solutions using an electrochemical quartz crystal microbalance (EQCM), building on our initial work at 1 M KOH where passivation was kinetically controlled. A porous passivating oxide spontaneously forms on Zn electrodes when KOH is above 4 M and saturated with zincate. However, passivation does not occur when bulk zincate concentration is decreased, resulting in continual Zn dissolution. EQCM data suggests that the passivation mechanism is strongly affected by pOH. Mass transport and kinetic processes in the 4 M KOH electrolytes couple and govern Zn passivation. At 8 M, KOH concentration shifts passivation to mass transport control. We explain this by the increased solubility of Zn(OH) 3 − with increasing pOH. The variation in the mechanism of passivation implications for how passivation is handled in Zn-alkaline batteries. The importance of controlling the mass transport increases with increased pOH, suggesting that electrode design, additives, and potential flow should be optimized. At lower pOHs, kinetics and mass transport must be balanced to manage passivation effectively. Additionally, the changing nature of the native oxide layer on the surface has implications for the evenness of deposition and dissolution on the Zn electrode.

Wittman, Reed M. [Oak Ridge National Laboratory (O↗
NASA NTRS1975

A generalized expression for lag-time in the gas-phase permeation of hollow tubes

A generalized expression for the nonsteady-state parameter, lag-time, has been obtained from Fick's second law for gas-phase transport through hollow, cylindrical membranes. This generalized expression is simplified for three limiting cases of practical interest: (1) diffusion controlled transport, (2) phase boundary reaction control at the inlet surface, and (3) phase boundary reaction control at the outlet surface. In all three cases the lag-time expressions were found to be inversely proportional only to the diffusion coefficient and functionally dependent on the membrane radii. Finally, the lag-time expressions were applied to experimentally obtained lag-time data for alpha-phase titanium and alpha-phase iron.

Shah, K. K.↗
DOE OSTI2026

Software Control Program For Transportable Microgrid State-of-charge Balancing And Frequency Stability Controls

A deterministic state-of-charge (SOC) balancing approach software control code is introduced as an integral secondary management to primary control layer of an islanded small microgrid or nanogrid system made up of multiple grid-forming inverter/battery/solar combination systems, where each set of batteries with each inverter are on independent DC buses (i.e. non-paralleled on the DC sides). A DERMS-level control approach, algorithm and automation controller program was developed to improve coordination and enable microgrid asset compliance and SOC balancing, enabling provision of a system-level power stability support architecture, load support, and asset scalability. The architecture is configured to treat each unit or micro/nano-grid as a node in a microgrid network, allowing for autonomous DERMS control regarding load and SOC balancing and power stability. As the network grows with the addition of units, greater coordination efforts may be required. The ideal small network microgrid ranges from 2-10 inverter/battery units before additional control parameters must be considered in the existing architecture. The control approach focuses on a deterministic state-of-charge analysis as the primary level control process followed by a secondary control loop using a forced frequency-watt droop strategy to conform off-the-shelf components into behaving under a leader-follower configuration. Adopting this control scheme has been shown to allow for a balanced, unit-coordinated microgrid network, enabling stable power flow. The deterministic state-of-charge approach is introduced as an integral primary control layer of an islanded small network microgrid. A standard strategy for SOC balancing is implementing a battery management system (BMS) to control SOC on the DC side. An alternative approach is to determine how to coordinate sending and receiving power on the AC side with multiple units. The latter approach assesses all the integrated units in the microgrid network. Once the individual units are identified, further system data is required to calculate each unit's total kWh, provided information about its capability to supply or consume kWh and availability. The secondary control layer in the multi-layered small network microgrid methodology uses the primary layer’s decision to initiate frequency setpoint changes, initializing the SOC balancing. The secondary control layer considers numerous system-dependent variables to enable a charging and discharging profile based on adjustable frequency setpoints. The combined architecture will result in stable, coordinated power flow enhancing an AC microgrid's functionalities.

Myers, KurtS [Idaho National Laboratory (INL), Ida↗
NASA NTRS1980

Preliminary calculations concerning the maintenance of the zonal mean ozone distribution in the Northern Hemisphere

Results from a three-dimensional photochemical-dynamical model of ozone are presented and a qualitative description of the maintenance of the ozone distribution and its seasonal variations below 1 mb is given. The transition between photochemical and transport control of the ozone distribution is emphasized. Between 1 and 10 mb, transport by the eddies seems to play only a minor role at mid-latitudes in producing the observed ozone distribution despite the zero correlation between ozone and temperature which occurs in that region. In the lower stratosphere, mean and eddy contributions to ozone change generally strongly offset one another. The buildup and decay of the springtime ozone maximum is discussed. Emphasis is given to the mechanism of ozone transport by the mid-latitude eddies, which play an important role in the springtime accumulation of ozone.

Cunnold, D. M.↗
DOE OSTI2022

Control of internal transport barriers in magnetically confined tokamak burning plasmas

The initiation, termination, and control of internal transport barriers associated with E × B flow shear near local minima of magnetic shear are examined for burning plasmas to determine if the positive feedback loops between profiles, instability, transport, and flow shear operate in regimes with fusion self-heating. A five-field transport model for the evolution of profiles of density, ion and electron temperature, ion and electron fluctuations, and radial electric field is utilized to examine the efficacy of controls associated with external inputs of heat and particles, including neutral beam injection, RF, pellets, and gas puffing. The response of the plasma to these inputs is studied in the presence of self-heating. The latter is affected by the external inputs and their modification of profiles and is, therefore, not an external control. Provided sufficient external power is applied, internal transport barriers can be created and controlled, both in ion and electron channels. Barrier control is sensitive to the locations of power deposition and pellet ablation, as well as temporal sequencing of external inputs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1993

Design, analysis, and control of large transport aircraft utilizing engine thrust as a backup system for the primary flight controls

A review of accidents that involved the loss of hydraulic flight control systems serves as an introduction to this project. In each of the accidents--involving transport aircraft such as the DC-10, the C-5A, the L-1011, and the Boeing 747--the flight crew attempted to control the aircraft by means of thrust control. Although these incidents had tragic endings, in the absence of control power due to primary control system failure, control power generated by selective application of engine thrust has proven to be a viable alternative. NASA Dryden has demonstrated the feasibility of controlling an aircraft during level flight, approach, and landing conditions using an augmented throttles-only control system. This system has been successfully flown in the flight test simulator for the B-720 passenger transport and the F-15 air superiority fighter and in actual flight tests for the F-15 aircraft. The Douglas Aircraft Company is developing a similar system for the MD-11 aircraft. The project's ultimate goal is to provide data for the development of thrust control systems for mega-transports (600+ passengers).

Gerren, Donna S.↗
NASA NTRS1979

Test and evaluation of Fern Engineering Company, Incorporated, solar heating and hot water system

Tests, test results, examination and evaluation by Underwriters Laboratory, Inc., of a single family solar heating and hot water system consisting of collector, storage, control, transport, and data acquisition are presented. The structural characteristics of the solar flat plate collectors were evaluated according to snow and wind loads indicated in various building codes to determine their suitability for use both Michigan and Pennsylvania where prototype systems were installed. The flame spread classification of the thermal insulation is discussed and the fire tests conducted on components are described. The operation and dielectrics withstand tests of the energy transport module indicate the module is capable of rated air delivery. Tests of the control panel indicate the relay coil temperatures exceed the temperature limits allowed for the insulating materials involved.

Source record↗
NASA NTRS2001

Genetic and chemical reductions in protein phosphatase activity alter auxin transport, gravity response, and lateral root growth

Auxin transport is required for important growth and developmental processes in plants, including gravity response and lateral root growth. Several lines of evidence suggest that reversible protein phosphorylation regulates auxin transport. Arabidopsis rcn1 mutant seedlings exhibit reduced protein phosphatase 2A activity and defects in differential cell elongation. Here we report that reduced phosphatase activity alters auxin transport and dependent physiological processes in the seedling root. Root basipetal transport was increased in rcn1 or phosphatase inhibitor-treated seedlings but showed normal sensitivity to the auxin transport inhibitor naphthylphthalamic acid (NPA). Phosphatase inhibition reduced root gravity response and delayed the establishment of differential auxin-induced gene expression across a gravity-stimulated root tip. An NPA treatment that reduced basipetal transport in rcn1 and cantharidin-treated wild-type plants also restored a normal gravity response and asymmetric auxin-induced gene expression, indicating that increased basipetal auxin transport impedes gravitropism. Increased auxin transport in rcn1 or phosphatase inhibitor-treated seedlings did not require the AGR1/EIR1/PIN2/WAV6 or AUX1 gene products. In contrast to basipetal transport, root acropetal transport was normal in phosphatase-inhibited seedlings in the absence of NPA, although it showed reduced NPA sensitivity. Lateral root growth also exhibited reduced NPA sensitivity in rcn1 seedlings, consistent with acropetal transport controlling lateral root growth. These results support the role of protein phosphorylation in regulating auxin transport and suggest that the acropetal and basipetal auxin transport streams are differentially regulated.

NASA Discipline Plant Biology↗
NASA NTRS1990

Simulated-airline-service flight tests of laminar-flow control with perforated-surface suction system

The effectiveness and practicality of candidate leading edge systems for suction laminar flow control transport airplanes were investigated in a flight test program utilizing a modified JetStar airplane. The leading edge region imposes the most severe conditions on systems required for any type of laminar flow control. Tests of the leading edge systems, therefore, provided definitive results as to the feasibility of active laminar flow control on airplanes. The test airplane was operated under commercial transport operating procedures from various commercial airports and at various seasons of the year.

Maddalon, Dal V.↗
NASA NTRS1981

Designing for aircraft structural crashworthiness

This report describes structural aviation crash dynamics research activities being conducted on general aviation aircraft and transport aircraft. The report includes experimental and analytical correlations of load-limiting subfloor and seat configurations tested dynamically in vertical drop tests and in a horizontal sled deceleration facility. Computer predictions using a finite-element nonlinear computer program, DYCAST, of the acceleration time-histories of these innovative seat and subfloor structures are presented. Proposed application of these computer techniques, and the nonlinear lumped mass computer program KRASH, to transport aircraft crash dynamics is discussed. A proposed FAA full-scale crash test of a fully instrumented radio controlled transport airplane is also described.

Thomson, R. G.↗