Search NASA⌕ Search

SEARCH · Search NASA

Results for “utility meter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

An evaluation of descent strategies for TNAV-equipped aircraft in an advanced metering environment

Investigated were the effects on system throughput and fleet fuel usage of arrival aircraft utilizing three 4D RNAV descent strategies (cost optimal, clean-idle Mach/CAS and constant descent angle Mach/CAS), both individually and in combination, in an advanced air traffic control metering environment. Results are presented for all mixtures of arrival traffic consisting of three Boeing commercial jet types and for all combinations of the three descent strategies for a typical en route metering airport arrival distribution.

Izumi, K. H.↗

Performance Analysis of the NAS Y-MP Workload

This paper describes the performance characteristics of the computational workloads on the NAS Cray Y-MP machines, a Y-MP 832 and later a Y-MP 8128. Hardware measurements indicated that the Y-MP workload performance matured over time, ultimately sustaining an average throughput of 0.8 GFLOPS and a vector operation fraction of 87%. The measurements also revealed an operation rate exceeding 1 per clock period, a well-balanced architecture featuring a strong utilization of vector functional units, and an efficient memory organization. Introduction of the larger memory 8128 increased throughput by allowing a more efficient utilization of CPUs. Throughput also depended on the metering of the batch queues; low-idle Saturday workloads required a buffer of small jobs to prevent memory starvation of the CPU. UNICOS required about 7% of total CPU time to service the 832 workloads; this overhead decreased to 5% for the 8128 workloads. While most of the system time went to service I/O requests, efficient scheduling prevented excessive idle due to I/O wait. System measurements disclosed no obvious bottlenecks in the response of the machine and UNICOS to the workloads. In most cases, Cray-provided software tools were- quite sufficient for measuring the performance of both the machine and operating, system.

Bergeron, Robert J.↗

Grid-Tied Photovoltaic Power System

A grid-tied photovoltaic (PV) power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. Operating costs of a PV power system are low compared to conventional power technologies. This method can displace the highest-cost electricity during times of peak demand in most climatic regions, and thus reduce grid loading. Net metering is often used, in which independent power producers such as PV power systems are connected to the utility grid via the customers main service panels and meters. When the PV power system is generating more power than required at that location, the excess power is provided to the utility grid. The customer pays the net of the power purchased when the on-site power demand is greater than the onsite power production, and the excess power is returned to the utility grid. Power generated by the PV system reduces utility demand, and the surplus power aids the community. Modern PV panels are readily available, reliable, efficient, and economical, with a life expectancy of at least 25 years. Modern electronics have been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy equal to the modern PV panels. The grid-tied PV power system was successfully designed and developed, and this served to validate the basic principles developed, and the theoretical work that was performed. Grid-tied PV power systems are reliable, maintenance- free, long-life power systems, and are of significant value to NASA and the community. Of particular value are the analytical tools and capabilities that have been successfully developed. Performance predictions can be made confidently for grid-tied PV systems of various scales. The work was done under the NASA Hybrid Power Management (HPM) Program, which is the integration of diverse power devices in an optimal configuration for space and terrestrial applications.

Eichenberg, Dennis J.↗

Global Carbon Consumption Database for Wildland Fire

Fire plays a significant role on both national and global scales, profoundly impacting landscapes shaped by human activity as well as those left wild. Even though fire can be devastating, wildland fire is a natural and integral force on our landscapes. Fires can also serve to reduce fuels to mitigate wildfire risk and maintain healthy ecosystem functions. However, the smoke produced by fires, regardless of their size or purpose, can pose adverse effects on human health when inhaled downwind. Understanding the influence of smoke on air quality and human well-being necessitates the quantification of emissions that fires release into the atmosphere. In response to this need, we have established a comprehensive global consumption database directly linked to distinct fuels within various fire danger categories. This database, featuring a spatial resolution of approximately 300 meters, builds upon the foundations of the Pettinari, M. Lucrecia (2015) Global Fuelbed database, a global fuel map with standardized Fuel Characteristic Classification System (FCCS) biomass parameters. Consumption is broken down into five Fire Danger categories (Low, Moderate, High, Very High, Extreme), for both ‘new’ and ‘residual’ burning scenarios. We define ‘residual burned area’ as area burning in a region that has burned on a previous day for the same fire season, and ‘new burned area’ as area burning in a region that has not recently burned. This product serves as a valuable tool when used in conjunction with burned area data to rapidly estimate the carbon consumed and released into the atmosphere. Previously, we developed a similar emissions method utilizing satellite information, in conjunction with the FCCS 30-meter United States fuelbed dataset. We implemented this approach on fires, documented during the 2019 Fire Influence on Regional to Global Environments and Air Quality (FIREX-AQ) campaign to estimate daily carbon emissions. Our emissions estimates were rigorously compared against in-situ measurements of CO2, CO, and black carbon aerosols, revealing a robust agreement between the two datasets.

Emily Gargulinski↗

Aerocapture Technology Development for Planetary Science - Update

Within NASA's Science Mission Directorate is a technological program dedicated to improving the cost, mass, and trip time of future scientific missions throughout the Solar System. The In-Space Propulsion Technology (ISPT) Program, established in 2001, is charged with advancing propulsion systems used in space from Technology Readiness Level (TRL) 3 to TRL6, and with planning activities leading to flight readiness. The program's content has changed considerably since inception, as the program has refocused its priorities. One of the technologies that has remained in the ISPT portfolio through these changes is Aerocapture. Aerocapture is the use of a planetary body's atmosphere to slow a vehicle from hyperbolic velocity to a low-energy orbit suitable for science. Prospective use of this technology has repeatedly shown huge mass savings for missions of interest in planetary exploration, at Titan, Neptune, Venus, and Mars. With launch vehicle costs rising, these savings could be the key to mission viability. This paper provides an update on the current state of the Aerocapture technology development effort, summarizes some recent key findings, and highlights hardware developments that are ready for application to Aerocapture vehicles and entry probes alike. Description of Investments: The Aerocapture technology area within the ISPT program has utilized the expertise around NASA to perform Phase A-level studies of future missions, to identify technology gaps that need to be filled to achieve flight readiness. A 2002 study of the Titan Explorer mission concept showed that the combination of Aerocapture and a Solar Electric Propulsion system could deliver a lander and orbiter to Titan in half the time and on a smaller, less expensive launch vehicle, compared to a mission using chemical propulsion for the interplanetary injection and orbit insertion. The study also identified no component technology breakthroughs necessary to implement Aerocapture on such a mission. Similar studies of Aerocapture applications at Neptune, Venus, and Mars were studied in 2003 through 2005. All showed significant performance improvements for the missions studied. Findings from these studies were used to guide the technology development tasks originally solicited in a 2002 NASA ROSS Research Announcement. The tasks are now in their final year and have provided numerous improvements in modeling and hardware, for use in proposals or new mission starts. Major Accomplishments: Since validation of the Aerocapture maneuver requires a space flight, ground developments have focused on modeling and environment prediction, materials, and sensors. Lockheed Martin has designed and built a 2-meter Carbon-Carbon aeroshell "hot structure." The article utilizes co-cured stiffening ribs and advanced insulation to achieve large scale, and up to a 40% reduction in areal density over the Genesis probe construction. This concept would be an efficient solution for probes that experience heat rates near 800-1000 W/cm(exp 2), such as at Venus and Earth. Applied Research Associates has extensively tested a family of efficient ablative TPS materials that provide solutions for a range of heating conditions. These materials are being applied to high-temperature structures built by ATK Space Systems, led by Langley Research Center. One-meter aeroshells will be thermally tested to validate construction and demonstrate higher bondline temperatures, which can lead to mass savings of up to 30% over traditional heatshields. Ames Research Center has developed aeroshell instrumentation that could measure environmental conditions and material performance during atmospheric entry. Instruments to measure TPS recession, heat flux, and catalycity could be combined with traditional sensors to provide a "plug-and-play" system for minimal mass and power, that would acquire flight data for model improvement and risk reduction on future missions. Improved atmospheric and aerothermodynamic models ha also been a major focus of the program. Next Steps: Aerocapture is one of five technologies in competition for a flight validation opportunity through the New Millennium Program. If selected, a fully autonomous vehicle will perform an Aerocapture at Earth in 2010, and flight data will be used to validate the guidance system and the TPS material for science mission infusion.

Munk, Michelle M.↗

Automatic inspection of analog and digital meters in a robot vision system

A critical limitation of most of the robots utilized in industrial environments arises due to their inability to utilize sensory feedback. This forces robot operation into totally preprogrammed or teleoperation modes. In order to endow the new generation of robots with higher levels of autonomy techniques for sensing of their work environments and for accurate and efficient analysis of the sensory data must be developed. In this paper detailed development of vision system modules for inspecting various types of meters, both analog and digital, encountered in a robotic inspection and manipulation tasks are described. These modules are tested using industrial robots having multisensory input capability.

Trivedi, Mohan M.↗

Thermal storage for electric utilities

Applications of the thermal energy storage (TES) principle (storage of sensible heat or latent heat, or heat storage in reversible chemical reactions) in power systems are evaluated. Load leveling behind the meter, load following at conventional thermal power plants, solar thermal power generation, and waste heat utilization are the principal TES applications considered. Specific TES examples discussed include: storage heaters for electric-resistance space heating, air conditioning TES in the form of chilled water or eutectic salt baths, hot water TES, and trans-seasonal storage in heated water in confined aquifers.

Swet, C. J.↗

A continuous physiological data collector

COP-DAC system utilizes oxygen and carbon dioxide analyzers, gas-flow meter, gas breathe-through system, analog computer, and data storage system to provide actual rather than average measurements of physiological and metabolic functions.

Bush, J. C.↗

Low-cost solar array structure development

Early studies of flat-plate arrays have projected costs on the order of $50/square meter for installed array support structures. This report describes an optimized low-cost frame-truss structure that is estimated to cost below $25/square meter, including all markups, shipping an installation. The structure utilizes a planar frame made of members formed from light-gauge galvanized steel sheet and is supposed in the field by treated-wood trusses that are partially buried in trenches. The buried trusses use the overburden soil to carry uplift wind loads and thus to obviate reinforced-concrete foundations. Details of the concept, including design rationale, fabrication and assembly experience, structural testing and fabrication drawings are included.

Wilson, A. H.↗

Flame Retardant Effect of Aerogel and Nanosilica on Engineered Polymers

Aerogels are typically manufactured vIa high temperature and pressure-critical-point drying of a colloidal metal oxide gel filled with solvents. Aerogel materials derived from silica materials represent a structural morphology (amorphous, open-celled nanofoams) rather than a particular chemical constituency. Aerogel is not like conventional foams in that it is a porous material with extreme microporosity and composed of individual features only a few nanometers in length with a highly porous dendriticlike structure. This unique substance has unusual properties such as low thermal conductivity, refractive index and sound suppression; in addition to its exceptional ability to capture fast moving dust. The highly porous nature of the aerogel's structure provides large amounts of surface area per unit weight. For instance, a silica aerogel material with a density of 100 kilograms per cubic meters can have surface areas of around 800 to 1500 square meters per gram depending on the precursors and process utilized to produce it. To take advantage of the unique properties of silica aerogels, especially the ultra light weight and low thermal conductivity, their composites with various engineering polymers were prepared and their flammability was investigated by Cone Calorimetry. The flammability of various polystyrene/silica aerogel nanocomposites were measured. The combination of these nanocomposites with a NASA patented flame retardant SINK were also studied. The results were compared with the base polymer to show the differences between composites with different forms of silica.

Williams, Martha K.↗

Synthesis and Properties of Cross-Linked Polyamide Aerogels

We report our ongoing research on polyamide aerogels made by step growth polymerization using a combination of terephthaloyl chloride, isophthaloyl chloride and m-phenylenediamine. Crosslinking of the amine capped polymer chains with 1,3,5-benzenetricarbonyl trichloride causes gelation in as little as two to five minutes. Removing the reaction solvent is accomplished through solvent exchange, followed by drying using supercritical CO2 extraction to give colorless aerogels with densities ranging from 0.07 to 0.33 grams per cubic centimeter and surface areas as high as 440 square meters per gram. Statistical experimental design methodology has been utilized to investigate dependence of properties of these aerogels, such as density, compressive modulus, and surface area, on changes in fabrication parameters including formulated number of amide oligomer repeat units (n-value), acid chloride (meta, para or combination), and solids concentration of solution used for gelation. For example, the density of these materials was found to be dependent on the acid chloride type and the solids concentration, but n was not a significant variable. However, surface area was significantly influenced by all three parameters. The polyamide aerogels represent a potential cost savings over previously reported polyimide aerogels, since monomers are all inexpensive and commercially available. Surface area and density were both highest when 100 terephthaloyl chloride was used but a combination of 5 solid concentration, 100 terephthaloyl chloride and n of 20 gave the best combination of properties.

cross-linked↗

Modal Test of Six-Meter Hypersonic Inflatable Aerodynamic Decelerator

A modal test was performed on the six-meter Hypersonic Inflatable Aerodynamic Decelerator (HIAD) test article to gain a firm understanding of the dynamic characteristics of the unloaded structure within the low frequency range. The tests involved various configurations of the HIAD to understand the influence of the tri-torus, the varying pressure within the toroids and the influence of straps. The primary test was conducted utilizing an eletrodynamic shaker and the results were verified using a step relaxation technique. The analysis results show an increase in the structure's stiffness with respect to increasing pressure. The results also show the rise of coupled modes with the tri-torus configurations. During the testing activity, the attached straps exhibited a behavior that is similar to that described as fuzzy structures in the literature. Therefore extensive tests were also performed by utilizing foam to mitigate these effects as well as understand the modal parameters of these fuzzy sub structures. Results are being utilized to update the finite element model of the six-meter HIAD and to gain a better understanding of the modeling of complex inflatable structures.

Abraham, Nijo↗

The use of airborne lasers in terrestrial and water environments

This document has the objective to provide some information regarding the applications for which an airborne laser system can be utilized. The considered data have been collected with the NASA Airborne Oceanographic Lidar (AOL), operational since 1977 as a flying laser laboratory. The most basic mode of operation of the AOL involves operation as a profiler. The data collected are similar to those which would be collected by a ground survey party. In the fluorosensing mode, pulsed laser light is used to induce fluorescence in various pigments contained in land and water targets. A capability for reliably mapping bottom geometry in clear ocean water to depths of 10-12 meters was also demonstrated, while other studies are related to the utilization of the AOL for synoptic mapping of surface layer concentrations of chlorophyll and other photopigments contained in phytoplankton.

Krabill, W. B.↗

Conceptual design of an advanced Stirling conversion system for terrestrial power generation

A free piston Stirling engine coupled to an electric generator or alternator with a nominal kWe power output absorbing thermal energy from a nominal 100 square meter parabolic solar collector and supplying electric power to a utility grid was identified. The results of the conceptual design study of an Advanced Stirling Conversion System (ASCS) were documented. The objectives are as follows: define the ASCS configuration; provide a manufacturability and cost evaluation; predict ASCS performance over the range of solar input required to produce power; estimate system and major component weights; define engine and electrical power condidtioning control requirements; and define key technology needs not ready by the late 1980s in meeting efficiency, life, cost, and with goalds for the ASCS.

Source record↗

Strain System for the Motion Base Shuttle Mission Simulator

The Motion Base Shuttle Mission Simulator (MBSMS) Strain System is an innovative engineering tool used to monitor the stresses applied to the MBSMS motion platform tilt pivot frames during motion simulations in real time. The Strain System comprises hardware and software produced by several different companies. The system utilizes a series of strain gages, accelerometers, orientation sensor, rotational meter, scanners, computer, and software packages working in unison. By monitoring and recording the inputs applied to the simulator, data can be analyzed if weld cracks or other problems are found during routine simulator inspections. This will help engineers diagnose problems as well as aid in repair solutions for both current as well as potential problems.

Huber, David C.↗

Development of the Large Aperture Reflector/Boom Assembly for the SMAP Spacecraft

The Jet Propulsion Laboratory's (JPL) Soil Moisture Active/Passive (SMAP) mission is to measure and monitor global soil moisture dynamics and freeze/thaw states. The rotating Reflector and Boom Assembly (RBA) on SMAP presents significant design and development challenges. The payload configuration utilizes a common Radiometer and Radar feedhorn and a 6-meter deployable mesh reflector all spinning at 14.6 rpm. The evolution of the RBA system solution, development of the mass properties management approach and RBA dynamics are discussed.

Earth observation mission↗

A Solar Sail Shape Modeling Approach for Attitude Control Design and Analysis

Solar sails operating in the space environment experience deformations in sail shape that result in relatively large disturbance torques which dictate the required performance of the spacecraft attitude control and momentum management systems. These deformations are driven by thermal loads on the booms (due to uneven solar heating), manufacturing and assembly tolerances, and variations in membrane tension. The Solar Cruiser spacecraft utilizes a four-quadrant sail design with four 30-meter length booms and four triangular sail membranes, creating a square sail structure of >1600 m2. Medium-fidelity mesh models were developed based on a characteristic deformed shape. A series of parametric studies were conducted using this shape paradigm to determine worst-case deformed sail shapes which produce bounding disturbance torques. A large database of shapes was produced, and the forces and moments induced by each individual shape were calculated using a Rios-Reyes reduced order generalized sail model. Two were selected as reference worst-case shapes for the Solar Cruiser mission: one which produced the highest pitch/yaw root-sum-squared (RSS) torque, and one which produced the highest roll torque. The results showed that the worst-case shapes at high solar incidence angles induce significantly higher (2-10x) disturbance torques than an ideal, flat-plate sail. Even with considerable safety margins, assuming an ideal sail is unlikely to sufficiently bound the disturbances, which is critical when designing the attitude control system and sizing actuators. Accurate sail shape modeling methodologies should therefore be employed on future solar sail missions.

Solar Sail↗

A Solar Sail Shape Modeling Approach for Attitude Control Design and Analysis

Solar sails operating in the space environment experience deformations in sail shape that result in relatively large disturbance torques which dictate the required performance of the spacecraft attitude control and momentum management systems. These deformations are driven by thermal loads on the booms (due to uneven solar heating), manufacturing and assembly tolerances, and variations in membrane tension. The Solar Cruiser spacecraft utilizes a four-quadrant sail design with four 30-meter length booms and four triangular sail membranes, creating a square sail structure of >1600 m2. Medium-fidelity mesh models were developed based on a characteristic deformed shape. A series of parametric studies were conducted using this shape paradigm to determine worst-case deformed sail shapes which produce bounding disturbance torques. A large database of shapes was produced, and the forces and moments induced by each individual shape were calculated using a Rios-Reyes reduced order generalized sail model [1]. Two were selected as reference worst-case shapes for the Solar Cruiser mission: one which produced the highest pitch/yaw root-sum-squared (RSS) torque, and one which produced the highest roll torque. The results showed that the worst-case shapes at high solar incidence angles induce significantly higher (2-10x) disturbance torques than an ideal, flat-plate sail. Even with considerable safety margins, assuming an ideal sail is unlikely to sufficiently bound the disturbances, which is critical when designing the attitude control system and sizing actuators. Accurate sail shape modeling methodologies should therefore be employed on future solar sail missions. References [1] L. Rios-Reyes and D. J. Scheeres, “Generalized Model for Solar Sails,” Journal of Spacecraft and Rockets, Vol. 42, Jan. 2005, pp. 182–185, 10.2514/1.9054.

Solar Sail↗