Search NASA⌕ Search

SEARCH · Search NASA

Results for “vertical stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Airloads research study. Volume 2: Airload coefficients derived from wind tunnel data

The development of B-1 aircraft rigid wind tunnel data for use in subsequent tasks of the Airloads Research Study is described. Data from the Rockwell International external structural loads data bank were used to generate coefficients of rigid airload shear, bending moment, and torsion at specific component reference stations or both symmetric and asymmetric loadings. Component stations include the movable wing, horizontal and vertical stabilizers, and forward and aft fuselages. The coefficient data cover a Mach number range from 0.7 to 2.2 for a wing sweep position of 67.5 degree.

Bartlett, M. D.↗
NASA NTRS1984

Residual-strength tests of L-1011 vertical fin components after 10 and 20 years of simulated flight service

Part of the NASA/ACEE Program was to determine the effect of long-term durability testing on the residual strength of graphite-epoxy cover panel and spar components of the Lockheed L-1011 aircraft vertical stabilizer. The results of these residual strength tests are presented herein. The structural behavior and failure mode of both cover panel and spar components were addressed, and the test results obtained were compared with the static test results generated by Lockheed. The effect of damage on one of the spar specimens was described.

Lopez, O. F.↗
NASA NTRS1983

Incorporating geometric and radiative effects into infrared scanning computer analysis

A NASA program, the SILTS experiment (Shuttle Infrared Leeside Temperature Sensing) will utilize an infrared scanning system mounted at the tip of the vertical stabilizer to remotely measure the surface temperature of the leeside of the Space Shuttle during entry from orbit. Scans of the fuselage and one wing will be made alternately. The experiment will correlate real full scale data to ground-based information. In order to quantitatively assess the temperature profile of the surface, an algorithm is required which incorporates the Space Shuttle shape, location of specific materials on the surface, and the measurement geometry between the camera and the surface. This paper will discuss the algorithm.

Myrick, D. L.↗
NASA NTRS1985

Space shuttle rudder/speedbrake actuation subsystem

The Rudder/Speedbrake (R/SB) Actuation Subsystem for use on the NASA Space Shuttle Orbiter is an electro-hydro-mechanical system which provides the control and positionary capability of the orbiter aero-dynamic primary flight control surface. The system is located in the vehicle's vertical stabilizer. The geared rotary actuators provide a power hinge feature of the split panel rudder. Actuation of both panels in the same direction provides conventional rudder control; actuating the panels differentially provides a speedbrake function intended to control both speed and pitch. The commands may be superimposed on one another. The system consists of one power drive unit which responds to quadredundant avionic signals to generate a rotary output, four geared rotary actuators, which develop rotary position and torque as outputs, and ten torque transmitting drive-shifts.

Naber, R. A.↗
NASA NTRS1985

Vapor Growth of Alloy-Type Semiconductor Crystals

The present effort is part of a continuing research program directed towards the investigation of basic vapor transport phenomena and of crystal growth properties of electronic materials. The primary purpose of ground-based studies is the development and definition of optimum experimental parameters for flight experiments. The ground-based effort includes the investigation of gravity-driven convection effects on mass transport rates and on crystal morphology for different orientations of the density gradient with respect to the gravity vector, and as a function of pressure and of temperature. In addition to the experimental tasks, theoretical efforts involve the quantitative thermodynamic analysis of the systems under investigation, the computation of fluid dynamic parameters, and the consideration of other possible effects on fluid flow under vertical, stabilizing and microgravity conditions. The specific experiments to be performed in a microgravity environment include the investigation of vapor transport and crystal growth phenomena of the GeSe-Xenon system and of the mass flux and growth of bulk and layer-type crystals of Hg sub (1-x) Cd sub x Te using HgI as a transport agent.

Wiedemeier, H.↗
NASA NTRS1985

Survey of ultraviolet shuttle glow

The University of Colorado Get Away Special (GAS) project utilizes the efforts of its students to place experiments on the shuttle. The objective of one experiment, the shuttle glow study, is to conduct a general survey of emissions in the ultraviolet near vehicle surfaces. An approximate wavelength range of 1900 to 3000 A will be scanned to observe predominant features. Special emphasis will be placed on studying the band structure of NO near 2000 A and the Mg+ line at 2800 A. The spectrometer, of Ebert-Faste 1/8-meter design, will perform the experiment during spacecraft night. It will be oriented such that the optical axis points to the cargo bay zenith. In order to direct the field-of-view of the instrument onto the shuttle vertical stabilizer (tail), a mirror assembly is employed. The mirror system has been designed to rotate through 7.5 degrees of arc using 10 positions resulting in a spatial resolution of 30 x 3 cm, with the larger dimension corresponding to the horizontal direction. Such a configuration can be attained from the forwardmost position in the cargo bay. Each spatial position will be subjected to a full spectral scan with a resolution on the order of 10 A.

Spear, K. A.↗
NASA NTRS1987

Dual keel space station control/structures interaction study

A study was made to determine the influence of truss bay size on the performance of the space station control system. The objective was to determine if any control problems existed during reboost and to assess the level of potential control/structures interaction during operation of the control moment gyros used for vertical stabilization. The models analyzed were detailed finite-element representations of the 5 meter and 9 foot growth versions of the 300 kW dual keel station. Results are presented comparing the performance of the reboost control system for both versions of the space station. Standards for comparison include flexible effects at the attitude control sensor locations and flexible contributions to pointing error at the solar collectors. Bode analysis results are presented for the attitude control system and control, structural, and damping sensitivities are examined.

Young, John W.↗
NASA NTRS1984

ACEE composite structures technology

The NASA Aircraft Energy Efficiency (ACEE) Composite Primary Aircraft Structures Program has made significant progress in the development of technology for advanced composites in commercial aircraft. Commercial airframe manufacturers have demonstrated technology readiness and cost effectiveness of advanced composites for secondary and medium primary components and have initiated a concerted program to develop the data base required for efficient application to safety-of-flight wing and fuselage structures. Oral presentations were compiled into five papers. Topics addressed include: damage tolerance and failsafe testing of composite vertical stabilizer; optimization of composite multi-row bolted joints; large wing joint demonstation components; and joints and cutouts in fuselage structure.

Klotzsche, M.↗
NASA NTRS1986

Comprehensive analysis of Shuttle Orbiter leeside surface infrared imagery obtained during atmospheric entry

The thermographic analysis techniques developed for processing of data from the Shuttle Infrared Leeside Temperature Sensing (SILTS) experiment are discussed. The SILTS experiment will obtain high-spatial-resolution infrared images of the leeside of the Space Shuttle Orbiter during atmospheric entry by means of a scanning infrared radiometer located atop the orbiter's vertical stabilizer. Comprehensive analysis of the SILTS thermography requires accurate consideration of all those factors (such as geometry of the observed surfaces, local surface emissivity, solar radiation, and other potential sources of image degradation) which may potentially affect the output of the infrared radiometer. An overview of the entire data processing procedure and brief descriptions of the data processing algorithms are presented.

Myrick, D. L.↗
NASA NTRS1987

A study of the TCAS 2 collision avoidance system mounted on a Boeing 737 aircraft

The purpose of this report is to determine the effects of scattering from major aircraft structures on the TCAS 2 collision avoidance system mounted on a Boeing 737. It is found that the major source of scattering for angles of observation above the horizon is the vertical stabilizer and that its effect may be greatly reduced by mounting the TCAS 2 array close to the nose of the aircraft. In addition, by mounting the array close to the nose, the effects of fuselage blockage on the array patterns at elevation angles below the horizon may be greatly reduced in the forward direction.

Grandchamp, B.↗
NASA NTRS1988

Convection in the vertical Bridgman-Stockbarger technique

The influence of operating parameters on convection in the Bridgman-Stockbarger technique was studied with a transparent furnace and melt. Convection was nearly nonexistent near the interface in the vertically stabilized configuration (temperature increasing with height). With the addition of a short booster heater between the main heater and the cooler, a destabilizing temperature gradient (temperature decreasing with height) was produced in the melt near the interface, and significant convection was produced throughout the entire melt. Convective velocities increased and flow symmetry improved as power to the booster heater was increased.

Neugebauer, Gregory T.↗
NASA NTRS1988

Effect of vertical magnetic field on convection and segregation in vertical Bridgman crystal growth

A previous finite-element analysis of vertical Bridgman growth for dilute and nondilute alloys is extended to include the effect of a vertically-aligned magnetic field in the limit of zero magnetic Reynolds number. Calculations are presented for growth of a dilute gallium-germanium alloy in a vertically stabilized Bridgman-Stockbarger system and in a furnace with a uniform temperature gradient imposed along the ampoule. Steady cellular convection driven by radial temperature gradients causes good axial and radial mixing in both systems without a magnetic field. A weak magnetic field decreases the intensity of convection and the effectiveness of solute mixing. The radial nonuniformity is greatest for an intermediate field strength. Stronger fields suppress flow recirculation completely, and lead to uniform solute segregation across the crystal and to diffusion-controlled axial segregation.

Kim, Do Hyun↗
NASA NTRS1988

The Flying Diamond: A joined aircraft configuration design project, volume 1

The results of the analysis conducted on the Joined Wing Configuration study are presented. The joined wing configuration employs a conventional fuselage and incorporates two wings joined together near their tips to form a diamond shape in both plan view and front view. The arrangement of the lifting surfaces uses the rear wing as a horizontal tail and as a forward wing strut. The rear wing has its root at the tip of the vertical stabilizer and is structurally attached to the trailing edge of the forward wing. This arrangement of the two wings forms a truss structure which is inherently resistant to the aerodynamic bending loads generated during flight. This allows for a considerable reduction in the weight of the lifting surfaces. With smaller internal wing structures needed, the Joined Wing may employ thinner wings which are more suitable for supersonic and hypersonic flight, having less induced drag than conventional cantilever winged aircraft. Inherent in the Joined Wing is the capability of the generation of direct lift and side force which enhance the performance parameters.

Ball, Chris↗
NASA NTRS1986

Independent Orbiter Assessment (IOA): Analysis of the rudder/speed brake subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The independent analysis results for the Orbiter Rudder/Speedbrake Actuation Mechanism is documented. The function of the Rudder/Speedbrake (RSB) is to provide directional control and to provide a means of energy control during entry. The system consists of two panels on a vertical hinge mounted on the aft part of the vertical stabilizer. These two panels move together to form a rudder but split apart to make a speedbrake. The Rudder/Speedbrake Actuation Mechanism consists of the following elements: (1) Power Drive Unit (PDU) which is composed of hydraulic valve module and a hydraulic motor-powered gearbox which contains differentials and mixer gears to provide PDU torque output; (2) four geared rotary actuators which apply the PDU generated torque to the rudder/speedbrake panels; and (3) ten torque shafts which join the PDU to the rotary actuators and interconnect the four rotary actuators. Each level of hardware was evaluated and analyzed for possible failures and causes. Criticality was assigned based upon the severity of the effect for each failure mode. Critical RSB failures which result in potential loss of vehicle control were mainly due to loss of hydraulic fluid, fluid contaminators, and mechanical failures in gears and shafts.

Wilson, R. E.↗
NASA NTRS1991

Tail venting for enhanced yaw damping at spinning conditions

An investigation was conducted in the NASA Langley 20-ft Vertical Spin Tunnel to determine the spin and spin-recovery characteristics of a 1/11-scale model of a low-wing general aviation airplane with a horizontal tail modified with variable-size gaps to allow ventilation of the vertical stabilizer and rudder. Erect spins at symmetric loadings were tested with varying gap sizes on either or both sides of the horizontal tail. The model results indicate that the basic airplane (with no gaps) exhibits a fast, flat spin from which no recoveries can be obtained. The airplane with the modified tail has either a fast, flat spin from which no recoveries or poor recoveries may be made, or a slower, steeper spin from which fair to excellent recoveries may be obtained, depending on the size and orientation of the tail gaps. The major contribution to spin recovery was from the gap on the leeward side of the tail. Gap widths of 15-25 percent of the tail semispan were needed to produce satisfactory recovery from the flat spin.

Stough, H. P., III↗
NASA NTRS1991

The SnoDog: Preliminary design of a close air support aircraft

U.S. military forces are presently searching for the next generation Close Air Support aircraft. The following report presents the SnoDog, a low-cost ($14.8 million) aircraft capable of operating from remote battlefields and unimproved airstrips. The configuration consists of a conventional, low aspect-ratio wing, twin booms, twin canted vertical stabilizers along with a high-mounted joined horizontal tail. A supercritical airfoil for the wing enhances aerodynamic performance, while the SnoDog's instability increases maneuverability over current close air support aircraft. Survivability was incorporated into the design by the use of a titanium tub to protect the cockpit from anti-aircraft artillery, as well as, the twin booms and retracted gear disposition. The booms aid survivability by supplying separated, redundant controls, and the landing gear are slightly exposed when retracted to enable a belly landing in emergencies. Designed to fly at Mach .76, the SnoDog is powered by two low-bypass turbofan engines. Engine accessibility and interchangeable parts make the SnoDog highly maintainable. The SnoDog is adaptable to many different missions, as it is capable of carrying advanced avionics pods, carrying external fuel tanks or refueling in-air, and carrying various types of munitions. This makes the SnoDog a multirole aircraft capable of air-to-air and air-to-ground combat. This combination of features make the SnoDog unique as a close air support aircraft, capable of meeting the U.S. military's future needs.

Ashbaugh, Scott↗
NASA NTRS1992

Estimates of tropical analysis differences in daily values produced by two operational centers

To assess the uncertainty of daily synoptic analyses for the atmospheric state, the intercomparison of three First GARP Global Experiment level IIIb datasets is performed. Daily values of divergence, vorticity, temperature, static stability, vertical motion, mixing ratio, and diagnosed diabatic heating rate are compared for the period of 26 January-11 February 1979. The spatial variance and mean, temporal mean and variance, 2D wavenumber power spectrum, anomaly correlation, and normalized square difference are employed for comparison.

Kasahara, Akira↗
NASA NTRS1993

Doppler global velocimetry measurements of the vortical flow above an F/A-18

A Doppler global velocimeter is employed to study the vortical flow above an F/A-18 at 25 degree angle of attack. The measurements indicate that the flow possessed the same characteristics as the vortical flow above a standard delta wing. Image to image comparisons clearly indicate that the flow striking the vertical stabilizers is not chaotic.

Lee, Joseph W.↗