Search NASA⌕ Search

SEARCH · Search NASA

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Effects of Nb on the Microstructure and Properties of Ti-Added Hypereutectic High-Cr Cast Iron

Effects of Nb on the microstructure and properties of Ti-added hypereutectic high-Cr cast iron were studied. With the addition of Nb, a new phase (Nb,Ti)C was formed. The microstructure analysis revealed that the amount of primary carbides was decreased from 18.6 to 8.8% and the primary and eutectic carbides were greatly refined. The decrease in the amount of primary carbides was attributed with the shrinking of primary M{sub 7}C{sub 3} phase zone in the phase diagram, while the refinement of primary carbides was attributed to the heterogeneous nucleus of (Nb,Ti)C phase for the primary M{sub 7}C{sub 3} carbides. The macrohardness of the alloy increased from 60.8 to 63.5HRC, and the impact toughness increased from 3.8 to 5.2 J cm{sup −2}. Furthermore, the wear resistance was enhanced with the addition of Nb due to the formation of hard (Nb,Ti)C carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Pulse MIG Welding of 6061-T6/A356-T6 Aluminum Alloy Dissimilar T-joint

Dissimilar T-joints between 4-mm-thick wrought 6061-T6 and cast A356-T6 aluminum alloy plates are made with pulse metal inert gas welding (P-MIG) process, and the weld geometry, microstructure and mechanical properties of the joints are investigated. The average tensile load of the joints is 9488 N at travel speed 12 mm/s and welding current 165 A with 6061 aluminum alloy as web plate and A356 aluminum alloy as flange plate. The weld zone (WZ) is composed of dendrite zone and columnar zone, which is wide at bottom of weld making it become a weak zone. Besides, grain boundary (GB) liquation, consisting of GB eutectic and solute-depleted α-Al, occurs in the partially melted zone on 6061 aluminum alloy side. The T-joint with highest tensile load fails at the root of WZ and the flange plate near the weld with different fracture modes.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Influence of Galvanizing Parameters on the Structural Development of Zn-Al-Based Coatings

The evolution of some layers’ characteristics, deposited by galvanization, was monitored according to the technological parameters of the process. Two types of alloys from the Zn-Al and Zn-Al-Ti-B systems were used for deposition. The structure of the deposited layers was analyzed by optical and electron microscopy. The chemical composition, phases and compounds in the structures were identified. The mechanical properties of the structural constituents of the layers were determined by nanoindentation. These techniques highlighted the typical non-uniformities in terms of composition and properties in the layers, mainly due to the diffusion and distribution of iron from the steel substrate in the deposited layers. The evaluation of iron diffusion in the deposited layer was done by differential thermal analysis. The values of the critical temperatures (melting temperature, eutectic temperature and solidification temperature) were correlated with the parameters used during deposition. It was observed that the structure of the coatings is layered, with a specific order from the steel substrate to the edge. In these layers, the constituents are mixtures of soft solid solutions of Al in Zn (η and β) and hard intermetallic compounds. Moreover, increasing the immersion time in the galvanizing bath and the bath temperature leads to an increase in iron diffusion in the coating layer, which contributes to lower coating thickness, thus reducing its durability in operation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Enhanced Strength of 304 SS-Ti6Al4V Laser-Welded Joints Containing Composite Interlayers

This paper investigates the microstructural characterization of the fracture propagation edge during laser beam welding of Ti6Al4V and 304 stainless steel using Cu, V, and Ni interlayers as a single Cu interlayer and composite interlayer structures with different Cu interlayer thicknesses. This study attempts to increase the Ti-SS joint strength through the use of the composite interlayers. X-ray diffraction characterization based on a 0.5-mm-thick Cu interlayer showed that the SS/Cu/Ti joint contained considerable brittle IMCs; however, the fracture surface of the SS/Cu-V/Ti composite interlayer sample did not contain any Fe-Ti IMCs or Cr{sub 2}Ti. EBSD observation indicated that the crack propagated transgranularly from solidified CuTi in the interdendritic regions of the FeTi compounds in the composite interlayer sample; however, the crack propagated intergranularly along Fe{sub 2}Ti grain boundaries in the single interlayer sample. The investigation based on a 1-mm-thick Cu interlayer showed that the SS/Ni-Cu1/Ti sample was stronger than the SS/Cu1/Ti sample due to a lack of CuTi at 3.5 kW. The tensile strength of the SS/Cu1-V/Ti joint was greater than that of the SS/Ni-Cu1/Ti joint due to the formation of ductile NiTi instead of brittle NiTi{sub 2}. The microstructures of the fracture edges after tensile testing illustrated that the eutectic CuTi + CuTi{sub 2} fractured at the SS/Cu1/Ti joint after tensile testing, while CuTi{sub 2} and eutectoid αTi + CuTi{sub 2} compounds fractured during the tensile experiment at the SS/Ni-Cu1/Ti and SS/Cu1-V/Ti joints, respectively. Investigations based on both the 0.5- and 1-mm-thick Cu interlayers showed that the tensile strength and elongation of the composite interlayer joints at a laser power of 3.5 kW were greater than those of the single interlayer joints.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Study on Microstructure and Properties of AZ31/6061 GTAW Butt Joints According to Mg-Cd-Al Ternary System

AZ31 Mg and 6061 Al were successfully joined by GTAW method with Cd as filler metal. The tensile strength of the joints reached 170 MPa through this alloying method according to Mg-Cd-Al ternary system. The microstructure, phases, element distribution and fracture mechanism of alloyed joints were studied. The results suggest that the fusion zone is mainly composed of CdMg compounds and Al-based solid solution. A transitional zone thickness of 40-80 μm with few primary Al{sub 12}Mg{sub 17} and fine Al{sub 12}Mg{sub 17}-MCMS (MCMS represents a mixture of CdMg and CdMg{sub 3} compounds) eutectic is formed between the AZ31 base metal and fusion zone. The fracture surface presents three distinct regions because of the different distribution of Al{sub 12}Mg{sub 17} compounds in the transitional zone. The alloying with Cd filler metal can disperse Al{sub 12}Mg{sub 17} intermetallic compounds and form CdMg ordered compounds with excellent plasticity. Thus, the mechanical properties of alloyed joints have been significantly enhanced.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Thermal Analysis of Cerium-Treated Chill-Cast Al-23 Si Alloy

The influence of elemental cerium addition on the cooling curve parameters and microstructure of hypereutectic Al-23Si alloy was investigated in this work. The cooling rate of the treated and untreated alloy samples was varied by solidifying the melt against chills of different materials in a stainless-steel tube. The cooling curve was recorded and nucleation temperatures of various phases in the alloy were measured. The results show that the chilling improves the effectiveness of the modifier. The two main phases of the alloy, primary silicon and eutectic silicon, were nucleated at temperatures of about 661.2 and 571.6 °C, respectively. The addition of Ce to slowly cooled alloys resulted in an increase in undercooling temperature of both the phases, with a decrease in its nucleation temperature, whereas the same additions increased the nucleation temperatures in chilled alloys. Based on the thermal analysis results, a relation between thermal analysis parameter (ΔT{sub G}) and silicon particle size of the alloy was proposed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Transmission Electron Microscopy (TEM) Study of the Oxide Layers Formed on Fe-12Cr-4Al Ferritic Alloy in an Oxygenated Pb-Bi Environment at 800°C

Liquid lead–bismuth eutectic (LBE) can serve as a heat transfer fluid for advanced nuclear applications as well as concentrated solar power but poses corrosion challenges for the structural materials at elevated temperatures. Oxide passivation of the surfaces of these materials during exposure to liquid LBE can inhibit such material degradation. In this study, transmission electron microscopy of oxides formed on Fe-Cr-Al alloy during exposure to lowoxygenated LBE at 800C has been performed. A complex structure of the oxide film has been revealed, consisting of a homogeneous inner layer of mostly Al 2 O 3 and a heterogeneous outer layer.

14 SOLAR ENERGY↗
DOE OSTI2023

Applications of biomass-derived solvents in biomass pretreatment – Strategies, challenges, and prospects

We report biomass pretreatment is considered a key step in the 2nd generation biofuel production from lignocellulosic biomass. Research on conventional biomass pretreatment solvents has mainly been focused on carbohydrate conversion efficiency, while their hazardousness and/or carbon intensity were not comprehensively considered. Recent sustainability issues request further consideration for eco-friendly and sustainable alternatives like biomass-derived solvents. Carbohydrate and lignin-derived solvents have been proposed and investigated as green alternatives in many biomass processes. In this review, the applications of different types of biomass pretreatment solvents, including organic, ionic liquid, and deep eutectic solvents, are thoroughly discussed. The role of water as a co-solvent in these pretreatment processes is also reviewed. Finally, current research challenges and prospects of utilizing biomass-derived pretreatment solvents for pretreatment are discussed. Given bioethanol's market potential and increasing public awareness about environmental concerns, it will be a priority adopting sustainable and green biomass pretreatment solvents in biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2026

Green pretreatment strategies for enhanced microbial lipid fermentation and synergistic high-quality lignin recovery for next-generation integrated biorefineries

Miscanthus × giganteus (Mxg) is a warm-season perennial grass being commercialized as a biomass feedstock for temperate farms. Three process strategies were compared for converting Mxg into single-cell oil and extracted lignin intermediates, as hydrothermal (HT) processing and two natural deep eutectic solvents (NADES), ChCl:LA (choline chloride:lactic acid) and ChCl:Gly (choline chloride:glycerol). Pretreatments were performed at 10% and 50% solids loading at 140 °C, 2 h; HT: 190 °C, 10 min. Enzymatic hydrolysates, generated at 10% solids using washed and unwashed biomass, were evaluated for microbial lipid production. Maximum glucose conversions from washed biomass reached 83.5% (ChCl:LA), 52.7% (ChCl:Gly), and 74.0% (HT). Remarkably, NADES-derived hydrolysates effectively replaced refined sugars for the cultivation of the oleaginous yeast Rhodotorula toruloides, achieving ∼51% higher biomass (OD 90.7) and lipid titers of 19.36 g/L within 45 h using a two-stage fermentation strategy. Lipid contents ranged from 34.5–44.5% dry weight, demonstrating reduced reliance on purified sugars. Beyond carbohydrate valorization, ChCl:LA pretreatment enabled high-purity lignin recovery (>89%) in a lignin-first strategy. Structural analyses (2D-HSQC and ³¹P NMR) showed syringyl (78.15%), guaiacyl (15.15%), and p-hydroxyphenyl (6.41%) units, with higher phenolic hydroxyl content (0.91 mmol/g) and a lower S/G ratio (0.19) than HT lignin (0.87 mmol/g, S/G 0.22). These attributes favor downstream lignin depolymerization into low-molecular-weight aromatics. Overall, NADES pretreatment simultaneously enhances microbial lipid yields and recovers high-quality lignin, advancing the economic feasibility of renewable diesel and sustainable aviation fuel (SAF) production from bioenergy crops within an integrated biorefinery framework.

2D HSQC↗
DOE OSTI2024

Physics-informed machine learning to predict solvatochromic parameters of designer solvents with case studies in CO 2 and lignin dissolution

The polarity of solvents plays a critical role in various research applications, particularly in their solubilities. Polarity is conveniently characterized by the Kamlet-Taft parameters that is, the hydrogen bonding acidity (α), the basicity (β), and the polarizability (π*). Obtaining Kamlet-Taft parameters is very important for designer solvents, namely ionic liquids (ILs) and deep eutectic solvents (DESs). However, given the unlimited theoretical number of combinations of ionic pairs in ILs and hydrogen-bond donor/acceptor pairs in DESs, experimental determination of their Kamlet-Taft parameters is impractical. To address this, the present study developed two different machine learning (ML) algorithms to predict Kamlet-Taft parameters for designer solvents using quantum chemically derived input features. The ML models developed in the present study showed accurate predictions with high R 2 and low RMSE values. Further, in the context of present interest in the circular bioeconomy, the relationship between the basicities and acidities of designer solvents and their ability to dissolve lignin and carbon dioxide (CO 2 ) is discussed. Our method thus guides the design of effective solvents with optimal Kamlet-Taft parameter values dissolving and converting biomass and CO 2 into valuable chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Binder jet printed WC infiltrated with pre-made melt of WC and Co

WC-Co was made via binder jet additive manufacturing of tungsten carbide followed by melt infiltration with a Co-WC infiltrant. The goal of the study was to achieve fully densified parts in near-net shape with minimal shrinkage while keeping the Co content low. The exact amount of infiltrant was determined in order to fully densify with minimum shrinkage based on the actual volume taken up by WC powder in the preform based on theoretical density, the bounding volume of prints after shrinkage, and the volume from the infiltrant. The eutectic nature of the infiltrant enabled melting at much lower temperature compared to the melting temperature of pure Co. The density, microstructure, grain size, hardness, and fracture toughness were characterized. The shrinkage and net shaping were assessed with light scans. A detailed look at the fracture mechanics was assessed. Here, this approach achieved highly dense WC-Co parts in net-shape with Co vol% of near 29 (Co wt% ~19), density of 96.2% theoretical, hardness of 8.34 GPa, grain size of 7.7 μm, magnetic saturation of 0.5 T, room temperature thermal conductivity of 125 W/mK, and fracture toughness of 24.7 = MPa·m 1/2 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

One-pot generation of lignin microspheres and digestible substrate with a polyol-DES pretreatment in high solid loading

Previous lignin microspheres (LMS) preparation needs multiple steps with very low yield and high cost. Herein, we developed a high-solid deep eutectic solvent (DES) pretreatment for an effective lignin fractionation and enzymatic saccharification of moso bamboo under mild temperature (110 °C) with high-solid loading. Lignin was significantly removed from the plant cell wall, and cellulose properties (e.g., crystallinity and degree of polymerization) were also altered during the pretreatment. As a result, the enzymatic digestibility of the pretreated bamboo was dramatically increased. Uniform micro-spherical lignin was directly produced from the pretreatment system, and its particle size could be regulated by controlling the solid loadings and pretreatment temperatures. The lignin microspheres formation mechanism was investigated by analyzing the lignin's size distribution, molecular weight distribution, chemical structure, and hydrophobicity. The DES showed excellent recyclability, and the recycled DES could still remove 42.78% lignin even after 7th circulation associated with 100% glucan saccharification. Further, the mass balance based on 1000 g biomass showed that 196.28 g LMS was directly recovered, which exhibited a high RhB adsorption. Besides, 404.91 g glucose and 36.67 g xylose were obtained after the enzymatic saccharification process. Specifically, GAPI analysis exhibited a near total green and yellow portions of the pictogram, indicating our DES process was green enough to make this biorefinery sustainable. Overall, the proposed DES generated synergistic productions of digestible solid and LMS which could contribute to establish a green and sustainable biorefinery sequence with diverse outputs in one pot.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Evaluation of Zn-rich coatings for IMC reaction control in aluminum-magnesium dissimilar welds

Highlights: • Thermodynamic and diffusion simulations have estimated the Zn conc. required to change the IMC reaction in Al-Mg dissimilar welding. • The selected coating alloy was effective in changing the Al-Mg reaction path by forming τ-(Al,Zn){sub 49}Mg{sub 32} as a substitute for β-Al{sub 3}Mg{sub 2}. • Refill™ friction stir spot welds produced with the coating alloy exhibited a thinner reaction layer and an increase in lap shear strength. - Abstract: The dissimilar welding of Al to Mg is very challenging owing to the rapid formation of an intermetallic (IMC) reaction layer at the joint interface, typically comprised of the binary phases γ-Al{sub 12}Mg{sub 17} and β-Al{sub 3}Mg{sub 2}. A potential metallurgical solution has been explored that aimed to change the reaction path by using Al-Zn alloy coatings to promote alternative IMCs with a slower growth rate. To determine the optimum composition for the coating, combined CALPHAD thermodynamic calculations and diffusion simulations were used to estimate the minimum Zn concentration (20 at.%) required to suppress the formation of the faster growing Al{sub 3}Mg{sub 2} phase. This prediction was verified by both static diffusion and Refill™ friction stir spot welding (FSSW) experiments. In each case the selected coating alloy was effective in changing the Al-Mg reaction path by forming the τ-(Al,Zn){sub 49}Mg{sub 32} phase as a substitute for β-Al{sub 3}Mg{sub 2}. However, in static heat treatments there was no reduction in the IMC reaction layer thickness due to the new phase having similar growth kinetics to the β-Al{sub 3}Mg{sub 2} phase it replaced. Nevertheless, Refill™ friction stir spot welds prepared with the new AL-Zn coating alloy exhibited a thinner reaction layer and an increase in lap shear strength. This benefit was attributed to the Zn addition reducing the joint interface liquation temperature, which resulted in a lower peak weld temperature and less IMC reaction; although an increase in local eutectic melting limited the improvement observed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure, precipitates and hardness of selectively laser melted AlSi10Mg alloy before and after heat treatment

Highlights: • Microstructural characterization of SLM AlSi10Mg alloy and comparison with cast and powder AlSi10Mg • Effect of solution heat treatment and aging on the hardness change of SLM AlSi10Mg alloy • Evolution of strengthening precipitates and Fe-rich intermetallics in SLM AlSi10Mg during heat treatment - Abstract: The microstructure and precipitates within selectively laser melted (SLM) AlSi10Mg alloys in the as-built state and after T6 heat treatment were examined and correlated to the hardness evolution. The as-built alloy exhibited columnar patterns perpendicular to the build-direction and fish-scale pattern along the build-direction originating from the melt pool. The microstructure consisted of fine Al cells and eutectic structure with up to 4 μm in size. Tiny needle-like Si particles with highly faulted structure were identified within the Al cells and formed semi-coherent interface with the matrix. Nanoscale Si particles and π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase were observed to segregate along the cell and grain boundary. Solution heat treatment (SHT) at 520 °C resulted in the dissolution of Al cellular microstructure. Precipitation and coarsening of the Si particles occurred, while the aspect ratio of Si particles remained nearly constant. The π-Al{sub 8}Si{sub 6}Mg{sub 3}Fe phase decomposed into plate-shaped β-Al{sub 5}SiFe. The artificial aging (AA) at 160 °C did not alter the microstructure but led to the formation of metastable Mg{sub 2}Si precipitates. The GP zones and β″ were identified through transmission electron microscopy after AA of 6 h, and β″ existed up to AA of 24 h. The hardness decreased after SHT due to the coarsening of the microstructure and reduced solid solution hardening. Hardness reached maximum magnitude after AA of 6–10 h due to the precipitation hardening, and remained relatively unchanged up to AA of 24 h. Microstructure and/or hardness of gas atomized powders and bulk cast AlSi10Mg alloys were also examined as references.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Grain boundary scavenging through reactive sintering of strontium and iron in samarium doped ceria electrolyte for ITSOFC applications

Highlights: • Addition of iron and strontium to Samarium doped ceria by combustion method and sintered at 1000 °C, 1200 °C, 1300 °C. • Viscous phase sintering of iron at 1200 °C modified to reactive sintering of iron and strontium at 1300 °C. • Grain boundary activation energy lowered without compensating the grain activation energy. • The highest scavenging factor of 10.52 with the lowest activation energy of 1.02eV was achieved. - Abstract: Lowering the operational temperature of ceria based electrolytes is important for commercialization of solid oxide fuel cells. Here, we report the effect of iron, strontium and iron/strontium co-addition in samarium (20 mol %) doped ceria (SDC) with respect to sintering, microstructural modifications and ionic conductivity. The nanoparticle synthesized through glycine-nitrate combustion method was sintered at 1000, 1200 and 1300 °C. An increase in density was observed in iron doped SDC due to viscous flow sintering while co-addition of strontium and iron lead to the reactive sintering at 1300 °C by forming a eutectic liquid phase which resulted in the density of 99%. The presence of iron and strontium generated a compensatory tensile strain in the lattice and an enhancement in oxygen vacancy concentration which resulted in higher ionic conductivity. Co-addition of strontium and iron in SDC, not only increases the density but also reduces the activation energy for grain boundary conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Capturing the softening in T91 steel annealed with molten LBE through interfacial gradient plasticity

In order to study the effect of annealing with molten lead–bismuth eutectic alloy (mLBE) on the mechanical properties of T91 steel, micropillar compression tests were analyzed through the consideration of mechanical interface energy terms within gradient plasticity. The stress–strain curves of the micropillars showed significant stochastic effects, characterized by a different elastic and plastic behavior response for each pillar. Among the various pillars, some exhibited a similar trilinear behavior. Scanning electron microscopy (SEM) images of these specimens demonstrated localized slip deformation and slip planes after compression, while transmission electron microscopy (TEM) images showed the presence of a severe slip zone along the random grain boundaries (RGBs), indicating that the GBs played a dominant role in the deformation/slip. By employing interfacial gradient plasticity that can explicitly account for the presence of GBs, the trilinear response was captured, allowing for the determination of the mechanical interface parameter. As anticipated the pillars which underwent severe slip at the GBs had a lower value for the mechanical interface parameter. Finally, annealing with mLBE can, therefore, in some cases result in softening in the overall stress–strain, as it lowers the mechanical interface energy of GBs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrodeposited nickel coatings for exceptional corrosion mitigation in industrial grade molten chloride salts for concentrating solar power

Molten chloride salt eutectics are attractive candidates for use as thermal energy storage media and heat transfer fluids in generation-three concentrating solar thermal power (Gen3 CSP) plants. However, corrosion of alloys in molten chloride salts, especially at high temperatures, is an extremely challenging problem that studies focus on lower temperatures, shorter durations, or analytical grade, and high-purity, salts. To date, there has been no study on corrosion or corrosion mitigation in an industrial-grade salt at a high temperature such as 750 °C. To alleviate this knowledge gap, the study presents new multiscale fractal-textured Ni coatings on various alloy surfaces for effective corrosion mitigation at 750 °C in molten chloride salts. Using the electrodeposition method, durable double-layer textured coatings were formed on stainless steel alloys (SS316, SS310, and SS347) and In800H. The corrosion performance of the coatings is investigated in both analytical-grade purity and, for the first time, practically relevant industrial-grade chloride salts. Ni-coated ferrous alloys showed an exceptionally reduced corrosion rate in the range of 350–480 μm/y in analytical-grade salts, and between 450 and 490 μm/y in purified industrial-grade salts at 750 °C. Ni coatings on ferrous alloys reduced corrosion rates by as much as 70% compared to uncoated surfaces and were comparable to the expensive Ha230 alloy with a high Ni content. As a result, by the use of innovative fractal corrosion mitigation coatings, for the first time, low-cost structural alloys are rendered viable for use with industrial-grade chloride salts, which is profoundly beneficial in practical systems.

14 SOLAR ENERGY↗
DOE OSTI2022

Promising Method of Sm–Co Magnet Reprocessing in Alkali Chloride Melts

Developing new, efficient methods for samarium and cobalt recovery from scraps/rejects and swarf at Sm–Co magnet manufacturing sites during shaping and finishing is an important task in terms of meeting their growing demand. In this work, the reaction of oxygen with a solution of samarium and cobalt chlorides in a LiCl–KCl eutectic melt was studied at 400–600 °C to explore possible methods for the separation and recovery of samarium and cobalt from these waste products. The pyrochemical reaction resulted in the formation and precipitation of samarium oxychloride, while the cobalt remained in the melt in a soluble chloride form. The effect of temperature and the amount of oxygen passed through the melt (oxygen-to-samarium molar ratio) on the course of the reaction were studied. Kinetic parameters of the oxygen with samarium chloride reaction were determined.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗