Search NASA⌕ Search

SEARCH · Search NASA

Results for “FAILURE MODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Flight test of a full authority Digital Electronic Engine Control system in an F-15 aircraft

The Digital Electronic Engine Control (DEEC) system considered is a relatively low cost digital full authority control system containing selectively redundant components and fault detection logic with capability for accommodating faults to various levels of operational capability. The DEEC digital control system is built around a 16-bit, 1.2 microsecond cycle time, CMOS microprocessor, microcomputer system with approximately 14 K of available memory. Attention is given to the control mode, component bench testing, closed loop bench testing, a failure mode and effects analysis, sea-level engine testing, simulated altitude engine testing, flight testing, the data system, cockpit, and real time display.

Barrett, W. J.↗
NASA NTRS1985

Strain isolated ceramic coatings

Plasma sprayed ceramic coatings are used in gas turbine engines to improve component temperature capability and cooling air efficiency. A compliant metal fiber strain isolator between a plasma sprayed ceramic coating and a metal substrate improves ceramic durability while allowing thicker coatings for better insulation. Development of strain isolated coatings has concentrated on design and fabrication of coatings and coating evaluation via thermal shock testing. In thermal shock testing, five types of failure are possible: buckling failure im compression on heat up, bimetal type failure, isothermal expansion mismatch failure, mudflat cracking during cool down, and long term fatigue. A primary failure mode for thermally cycled coatings is designated bimetal type failure. Bimetal failure is tensile failure in the ceramic near the ceramic-metal interface. One of the significant benefits of the strain isolator is an insulating layer protecting the metal substrate from heat deformation and thereby preventing bimetal type failure.

Tolokan, R. P.↗
NASA NTRS2006

Analysis of Composite Panel-Stiffener Debonding Using a Shell/3D Modeling Technique

Interlaminar fracture mechanics has proven useful for characterizing the onset of delaminations in composites and has been used with limited success primarily to investigate onset in fracture toughness specimens and laboratory size coupon type specimens. Future acceptance of the methodology by industry and certification authorities however, requires the successful demonstration of the methodology on structural level. For this purpose a panel was selected that was reinforced with stringers. Shear loading cases the panel to buckle and the resulting out-of-plane deformations initiate skin/stringer separation at the location of an embedded defect. For finite element analysis, the panel and surrounding load fixture were modeled with shell element. A small section of the stringer foot and the panel in the vicinity of the embedded defect were modeled with a local 3D solid model. A failure index was calculated by correlating computed mixed-mode failure criterion of the graphite/epoxy material.

Krueger, Ronald↗
DOE OSTI2021

Development of dispensing hardware for safe fueling of heavy duty vehicles

The development of safe dispensing equipment for the fueling of heavy duty (HD) vehicles is critical to the expansion of this newly and quickly expanding market. This paper discusses the development of a HD dispenser and nozzles assembly (nozzle, hose, breakaway) for these new, larger vehicles where flow rates are more than double compared to light duty (LD) vehicles. This equipment must operate at nominal pressures of 700 bar, -40o C gas temperature, and average flow rate of 5-10 kg/min at a high throughput commercial hydrogen fueling station without leaking hydrogen. The project surveyed HD vehicle manufacturers, station developers, and component suppliers to determine the basic specifications of the dispensing equipment and nozzle assembly. The team also examined existing codes and standards to determine necessary changes to accommodate HD components. From this information, the team developed a set of specifications which will be used to design the dispensing equipment. In order to meet these goals, the team performed computational fluid dynamic, pressure modelling, and temperature analysis in order to determine the necessary parameters to meet existing safety standards modified for HD fueling. The team also considered user, operational, and maintenance requirements, such as freeze lock which has been an issue which prevents the removal of the nozzle from LD vehicles. The team also performed a failure mode and effects analysis (FMEA) to identify the possible failures in the design. The dispenser and nozzle assembly will be tested separately, and then installed on an innovative, HD fueling station which will use a HD vehicle simulator to test the entire system.

08 HYDROGEN↗
DOE OSTI2020

The Corrective Maintenance Paradigm Shift at Hanford's Tank Farms - 20077

Hanford's Tank Farms facilities have been used to safely store waste for over 70 years, with the first single-shell tanks being constructed in 1943. Tank Farm facilities consist of 149 single-shell tanks, 28 double-shell tanks, an evaporator facility, and wastewater treatment facilities. Tank Farm facilities are aging, with a tremendous corrective maintenance burden on the Tank Farm contractor. The mission of Tank Farm facilities is soon changing from waste storage to waste staging for the Hanford Waste Treatment and Immobilization Plant (WTP). WTP operations will demand a significant increase in Tank Farm facility operations, in which corrective maintenance outage windows will shrink drastically. This realization has forced the Tank Farm contractor to consider a paradigm shift in Tank Farm facilities Maintenance planning, and the use of reliability Engineering tools. The Tank Farm Production Operations Engineering Cognizant System Engineering (CSE) organization has led the way in motivating this paradigm shift. This shift has been realized through the use of: 1) technical exchange with other Department of Energy (DOE) contractors to develop improvements in the CSE program, 2) a shift from the use of lagging to leading system health indicators, and 3) a Plant Health Committee to unite Engineering, Operations, and Maintenance personnel toward a productive maintenance strategy. The CSE organization has held several technical exchanges with other DOE contractors to discuss CSE concepts, and how to better maintain aging infrastructure. The technical exchange with other contractors has greatly reduced the time required to make improvements in the Tank Farm CSE program. Other DOE contractors have already faced issues surrounding aging infrastructure, and have vast experience in improving the reliability and usable life of structures and components in nuclear facilities. The past CSE program used lagging health indicators to determine the health of systems. The key lagging indicator used to determine system health was availability, which is the percentage of time that a facility was ready for operation compared to the time the facility was demanded for operation. Availability was a good indicator of health in the waste storage mission of Tank Farms, where safe storage was the most important function of the facility, and where maintenance outage windows were typically long-duration. In current and future operations, outage windows are reducing, resulting in the need for much more reliable systems. Systems that have had high availability may suddenly become inoperable due to a failed component or sub-system. In several instances, the use of availability as an indicator of system health failed to predict system/equipment failure before its occurrence. In discussions with other DOE contractors, a set of reliability tools, including leading indicators of health, has been implemented in the CSE program. This primarily involves the use of failure modes and effects analysis and the study of equipment failure to develop system monitoring plans that focus on trending data to detect oncoming equipment failure ahead of time. In addition, the use of a Plant Health Committee has added significantly to the paradigm shift from a corrective maintenance philosophy to the use of predictive and preventive maintenance. The Plant Health Committee is a chartered team consisting of Engineering, Operations, and Maintenance personnel. CSEs use this forum to present the results of their performance monitoring, including the presentation of health via leading health indicators. The most positive aspect of this committee is the communication that it creates within these critical organizations. The Operations and Maintenance organization benefit from focusing maintenance on the reliability-centered focus provided by Engineering. Engineering benefits from the operational experience of the Operations organization and from the failure data that can be provided by Maintenance personnel. The continued use of the Plant Health Committee is expected to further decrease maintenance outage times, in better support of oncoming 24/7 operations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2018

Composite Technology for Exploration (CTE)

Technology Product Capability: The CTE (Composite Technology for Exploration) project will develop and demonstrate critical composites technologies with a focus on weight-saving, performance-enhancing bonded joint technology for Space Launch System (SLS)-scale composite hardware to support future NASA exploration missions - Improve the analytical capabilities required to predict failure modes in composite structures; - and, Support SLS payload adapters and fittings by maturing composite bonded joint technology and analytical tools to enable risk reduction. Exploration & Science Impact: Lighter weight structures; Improved material predictive capabilities; Improved bonded joint failure load and mode predictions to help reduce knockdown factors; and improve predictability and reliability; Increase confidence of all bonded joint composite structures; Reduce reliance on expensive testing.

CTE↗
DOE OSTI2018

Multi-scale computational analysis of unidirectional carbon fiber reinforced polymer composites under various loading conditions

In this study, a multi-scale computational analysis based on representative volume element (RVE) modeling and molecular dynamics (MD) simulations is developed to investigate the microscopic failure mechanisms of unidirectional (UD) carbon fiber reinforced polymer (CFRP) composites. The average properties of the 200-nm thickness interphase region between fiber and matrix are characterized through MD simulations and an analytical gradient model. The results demonstrate that the interphase region has higher Young’s modulus and strength, compared to the bulk matrix. This stiffened interphase region influences the composite response significantly. Specifically, the traditional two-phase model with zero-thickness interface fails to capture the stress-strain behavior compared to the experimental data. However, by adding the interphase region to a modified RVE model, the accuracy of simulation results will be improved significantly. Furthermore, a coupled experimental-computational micromechanics approach is adopted to calibrate and validate the cohesive parameters of the interface. By including the cohesive interface, our modified RVE model accurately captures the failure strength of the composites. Finally, different failure mechanisms for specimens are investigated using our multi-scale computational framework. In conclusion, the results show that the failure modes of UD CFRP composites are very complex and multiple failure mechanisms co-exist depending on the loading conditions, agreeing well with our experimental analyses.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In-Sodium Testing of a Prototype Thermoacoustic Power Sensor for Sodium-Cooled Fast Reactors

The ultimate goal of this project is to develop and demonstrate a thermoacoustic power sensor (TAPS) for Sodium-Cooled Fast Reactors (SFRs), with potential application also envisioned to other nuclear technologies such as Lead-Cooled Fast Reactors (LFRs), Molten Salt Reactors (MSRs), in addition to Light Water Reactors (LWRs). The project was led by Westinghouse Electric Company, LLC (Westinghouse) and carried out in collaboration with Argonne National Laboratory (ANL) and the University of Pittsburgh. A TAPS is a passive (self-powered), non-invasive (wireless) sensor envisioned for measuring key parameters, such as local temperature and neutron flux, in a nuclear reactor core. The sensor generates pressure waves (i.e., sound waves) with a frequency and amplitude dependent upon nuclear operating conditions (coolant temperature or power changes). The acoustic waves are able to travel through the core and associated structures, and reach to the sensor network placed outside and/or inside of the reactor vessel. These sensors require a very small amount of power which, during loss of power events, can be provided, for example, by harvesting gamma radiation energy, thus resulting in a monitoring system that can function both during normal operation and during loss of power events. Westinghouse and the University of Pittsburgh designed and fabricated TAPS prototypes for Argonne National Laboratory (ANL) to carry out in-sodium testing to evaluate the effects of sodium on the TAPS and the performance of the TAPS technique in sodium. Argonne received a TAPS prototype from Westinghouse, and the prototype was modified such that it can be installed into a test vessel and function in sodium at elevated temperature without potentially leaking. A water mockup test apparatus was constructed to validate proper working of the prototype. An instrumentation and control (I&C) system, running on the National Instruments (NI) LabView platform, was developed to: 1) operate both the water mockup test and the in-sodium test facility; and 2) process and analyze the received acoustic signals from an array of accelerometers and the Argonne sodium-submersible high-temperature acoustic sensor. The prototype was successfully tested in a water bath at different temperatures. Water mockup tests demonstrated that the TAPS prototype is working properly and its resonance frequency changes linearly with the coolant (water) temperature. A TAPS test apparatus was constructed and integrated with the upgraded Under-Sodium Viewing (USV) sodium test facility. The integrated USV-TAPS sodium test facility has been operational. The TAPS prototype and a high-temperature sodium-submersible acoustic sensor (SSAS) developed by Argonne were both installed inside the TAPS test vessel. Being operated within argon cover gas under ambient conditions, the TAPS prototype demonstrated that it was functioning properly with a resonance frequency at 1407.2 Hz, which was successfully detected by the accelerometers mounted on the external wall of the vessel and the high-temperature SSAS installed inside the vessel. After successfully transferring sodium into the vessel, in-sodium tests of the prototype were conducted. Tests of the TAPS prototype demonstrated that the resonance frequency of the TAPS changes linearly with respect to the temperature difference between the interior of the TAPS and bulk sodium. The early tests showed that the TAPS prototype could not establish a continuous and consistent resonance in sodium. The resonance diminished before the prototype reached its operating temperature. A signal postprocessor was added to the DAQ module latterly to isolate interferences, enhance signal conditioning, improve peak detection, and generate resonance frequency versus temperature plots. After testing in molten sodium and immersion at higher temperature for several weeks, the TAPS prototype was able to establish a continuous resonance. Performance evaluation of the TAPS prototype was then conducted in sodium. The tests included the investigation of 1) the effects of the temperature difference between the TAPS and bulk sodium, 2) the effects of sodium flowrate; and 3) the performance of the different sensor-receiver systems positioned inside or outside the vessel. Results of a test demonstrated that, with limited sodium circulation, a continuous and consistent resonance of the TAPS prototype was established occasionally. The tests also demonstrated that, because of the nature of detection principles and mounting methods, the high temperature SSAS is more affected by acoustic noise, while accelerometers are more affected by vibrations, in the test environment. It is unknown why the TAPS prototype only occasionally established a continuous and consistent resonance when the TAPS temperature reached its operating temperature in molten sodium, and why it ultimately failed to resonate at all. A failure modes assessment was conducted and a few potential causes of failure were identified. Different post in-sodium tests were conducted to obtain additional information potentially relevant to the cause of the failure. Nondestructive evaluation techniques are suggested to examine the internal integrity as well as the gas mixture of the prototype. If they prove inconclusive, the prototype should be cut open to conduct a thorough inspection of its internal integrity and determine the state of the gas mixture.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Testing Recommendations for Thermal Failure Analysis

Minimizing ranges of uncertainty in failure QOIs is vital for making informed engineering decisions. To improve our decision-making ability, it is necessary to have a QOI representation that captures more complex failure modes. Capturing the physics of complex time-dependent temperature failure in explicit detail can be computationally and experimentally expensive. To avoid this blooming of complication and costs, an empirical QOI component-level failure/damage model may be sufficient to help identify component-level failure. In this context, failure and damage are abstractions of more complicated processes that lead to the cessation of normal operating behavior, not a representation of mechanical damage, such as void formation. Such a model requires minimal increases in computational cost and experimental burden. The proposed QOI serves as an indicator that something has likely failed, similar to the previous critical failure temperatures or pressures. This QOI will not replace any existing failure QOIs. It will be calculated alongside them, allowing for preservation of legacy style QOI measurements with new context from the new QOI.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Microstructural characterization of the HRSI thermal protection system for space shuttle

Components of the space shuttle high temperature reusable surface insulation (HRSI) system were microscopically characterized, both separately and as a system, to obtain information needed for stress analysis models of the thermal protection system. A tension specimen of the HRSI system was loaded in steps and was microscopically observed at each load condition to demonstrate the tension failure mode associated with strain isolation pad (SIP) behavior. A local failure occurred which should be associated with transfer of load through transverse fibers in the SIP. Stress concentrations attributed to the SIP behavior necessitated strengthening of the HRSI by densification of the RSI at the bondline. An HRSI tile was microscopically characterized after the densification process. The densified surface layer blended into the RSI which caused a gradual change in density. The gradation in density does not appear to represent a sharp discontinuity in elastic modulus between the densified layer and the parent material.

Ransone, P. O.↗
NASA NTRS1982

Influence of layer thickness on the strength of angle-ply laminates

Experimental results are presented showing that the strength and toughness of finite width angle-ply laminates can be increased significantly by using an alternating layer stacking sequence as opposed to a clustered configuration. The ultimate tensile stress of an alternating plus/minus theta laminate of the form (+ or - theta) sub 2 sub s can be much as 1.5 times that of a clustered configuration of the form theta sub 2/-theta sub 2 sub s. Further, the toughness of the alternating layer configuration can be as much as 2.7 times that of the clustered configuration. These differences are explained analytically through consideration of the influence of layer thickness on the magnitude of the interlaminar shear stress and by examination of failed specimens. It is shown that the two laminate configurations exhibit distinctly different failure modes for some fiber angles. Both laminate configurations exhibit catastrophic failure with the damage limited essentially to a small region defined by the length of a single crack across the width of the specimen, parallel to the fiber direction. Results are presented for T300/5208 graphite-epoxy for fiber orientations of 10, 30, and 45 deg.

Herakovich, C. T.↗
NASA NTRS2016

Functional Fault Model Development Process to Support Design Analysis and Operational Assessment

A functional fault model (FFM) is an abstract representation of the failure space of a givensystem. As such, it simulates the propagation of failure effects along paths between the origin ofthe system failure modes and points within the system capable of observing the failure effects. Asa result, FFMs may be used to diagnose the presence of failures in the modeled system. FFMsnecessarily contain a significant amount of information about the design, operations, and failuremodes and effects. One of the important benefits of FFMs is that they may be qualitative, ratherthan quantitative and, as a result, may be implemented early in the design process when there ismore potential to positively impact the system design. FFMs may therefore be developed andmatured throughout the monitored system's design process and may subsequently be used toprovide real-time diagnostic assessments that support system operations. This paper provides anoverview of a generalized NASA process that is being used to develop and apply FFMs. FFMtechnology has been evolving for more than 25 years. The FFM development process presented inthis paper was refined during NASA's Ares I, Space Launch System, and Ground SystemsDevelopment and Operations programs (i.e., from about 2007 to the present). Process refinementtook place as new modeling, analysis, and verification tools were created to enhance FFMcapabilities. In this paper, standard elements of a model development process (i.e., knowledgeacquisition, conceptual design, implementation & verification, and application) are describedwithin the context of FFMs. Further, newer tools and analytical capabilities that may benefit thebroader systems engineering process are identified and briefly described. The discussion isintended as a high-level guide for future FFM modelers.

Melcher, Kevin J.↗
NASA NTRSDate not supplied

Knowledge Discovery for Early Failure Assessment of Complex Engineered Systems Using Natural Language Processing

Emerging complex engineered systems may have unexpected safety issues due to novel operational environments, increasing autonomy, human-machine interaction, and other factors. To prevent failures in operation or testing that necessitate costly redesign, it is desirable to predict likely failure modes early in the design process. Information about past engineering failures in natural language format presents one possible solution by enabling the retrieval of information that can inform new designs. However, identifying documents containing usable information and extracting the required information can be prohibitively time-consuming when implemented at scale. In this research, an automated natural language processing (NLP) framework is proposed to discover relevant knowledge from documents containing failure-related design information. The framework is applied to NASA’s Lessons Learned Information System (LLIS),which is publicly available. Documents containing usable information are filtered using two different NLP-based models. Next, from the identified usable documents, a failure taxonomy is extracted using a partitioned hierarchical topic modeling approach. Partitions of the document describe different sections of the failure taxonomy – i.e., failure, cause of failure, and recommendations – as indicated by the structure of the original document. The extracted failure taxonomy can be leveraged in early design failure assessment methods. Moreover, the framework can be used to identify documents containing usable failure-related design information from other databases and extract relevant information from these documents.

Documentation and Information Science↗
NASA NTRSDate not supplied

Knowledge Discovery for Early Failure Assessment of Complex Engineered Systems Using Natural Language Processing

Emerging complex engineered systems may have unexpected safety issues due to novel operational environments, increasing autonomy, human-machine interaction, and other factors. To prevent failures in operation or testing that necessitate costly redesign, it is desirable to predict likely failure modes early in the design process. Information about past engineering failures in natural language format presents one possible solution by enabling the retrieval of information that can inform new designs. However, identifying documents containing usable information and extracting the required information can be prohibitively time-consuming when implemented at scale. In this research, an automated natural language processing (NLP) framework is proposed to discover relevant knowledge from documents containing failure-related design information. The framework is applied to NASA’s Lessons Learned Information System (LLIS),which is publicly available. Documents containing usable information are filtered using two different NLP-based models. Next, from the identified usable documents, a failure taxonomy is extracted using a partitioned hierarchical topic modeling approach. Partitions of the document describe different sections of the failure taxonomy – i.e., failure, cause of failure, and recommendations – as indicated by the structure of the original document. The extracted failure taxonomy can be leveraged in early design failure assessment methods. Moreover, the framework can be used to identify documents containing usable failure-related design information from other databases and extract relevant information from these documents.

Documentation and Information Science↗
NASA NTRSDate not supplied

Material Variability Effects on Damage Development Within Composite Adhesively Bonded Joints

Use of composite adhesively bonded joints (ABJ) is of critical importance to the adoption of composite materials in the automotive industry, as ABJ enable lower stress concentrations as compared to conventional mechanically fastened joints. ABJ are better suited for joining composite materials as compared to fastened joints because fastened joints require drilling of holes which locally affect composite material structure. Composite materials and adhesives are subject to unavoidable stochastic local material variations which make different failure scenarios possible. An experimentally tested ABJ configuration is simulated using finite element analysis (FEA). Experimentally, under tension, the joints failed by three major failure modes, with peak loads ranging from 13.0-16.1 kips. Progressive failure analysis tools are used to simulate damage development within each material within the joint. The simulation agreed well with the average experimental peak load. Stochastically occurring adhesive porosity and matrix-fiber micro-disbonding were numerically simulated. The simulations revealed a similar trend as observed experimentally: joints which failed at higher peak loads had lower levels of damage within the face-sheets of the composite panels which were adhesively bonded; these joints which failed at higher peak loads also had greater damage in the doubler of the experimentally tested double lap joint configuration.

Richard Larson↗
NASA NTRS2025

Detangling Safety Knowledge with Contextualism

We have contradictory intuitions about knowing that things are safe: on the one hand, we claim to have knowledge that many systems (even complex ones) are safe in ordinary language. On the other hand, when challenged by an expert, we easily admit that we do not, in fact, possess very much safety knowledge at all. This Technical Memorandum (TM) attempts to reconcile these two competing intuitions using a philosophical view called epistemic contextualism. We can use epistemic contextualism to explain the importance of safety regulations and the goal in implementing them: first, to differentiate types of disagreement and establish a common basis upon which regulators and regulatees can know that a system is safe; second, to raise ordinary consumers’ standards for safety knowledge (given adequate knowledge of the comprehensiveness of the regulation). This TM also uses the contextualist framework of relevant alternatives to elucidate types of failure possibilities and explain complications in attempts to prevent common mode failures.

language↗
NASA NTRS1999

Synergistic Effects of Physical Aging and Damage on Long-Term Behavior of Polymer Matrix Composites

The research consisted of two major parts, first modeling and simulation of the combined effects of aging and damage on polymer composites and secondly an experimental phase examining composite response at elevated temperatures, again activating both aging and damage. For the simulation, a damage model for polymeric composite laminates operating at elevated temperatures was developed. Viscoelastic behavior of the material is accounted for via the correspondence principle and a variational approach is adopted to compute the temporal stresses within the laminate. Also, the effect of physical aging on ply level stress and on overall laminate behavior is included. An important feature of the model is that damage evolution predictions for viscoelastic laminates can be made. This allows us to track the mechanical response of the laminate up to large load levels though within the confines of linear viscoelastic constitutive behavior. An experimental investigation of microcracking and physical aging effects in polymer matrix composites was also pursued. The goal of the study was to assess the impact of aging on damage accumulation, in ten-ns of microcracking, and the impact of damage on aging and viscoelastic behavior. The testing was performed both at room and elevated temperatures on [+/- 45/903](sub s) and [02/903](sub s) laminates, both containing a set of 90 deg plies centrally located to facilitate investigation of microcracking. Edge replication and X-ray-radiography were utilized to quantify damage. Sequenced creep tests were performed to characterize viscoelastic and aging parameters. Results indicate that while the aging times studied have limited ]Influence on damage evolution, elevated temperature and viscoelastic effects have a profound effect on the damage mode seen. Some results are counterintuitive, including the lower strain to failure for elevated temperature tests and the catastrophic failure mode observed for the [+/- 45/9O3](sub s), specimens. The fracture toughness for transverse cracks increases with increasing temperature for both systems: transverse cracking was completely absent prior to failure in [+/- 45/903](sub s), and was suppressed for [02/903](sub s). No significant effect of damage on aging or viscoelastic parameters was observed.

Brinson, L. Cate↗