Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUIDIZATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Attrition of hematite particles for chemical looping combustion in a conical jet cup

The attrition of hematite particles for use in the chemical looping combustion process was investigated using a cold flow jet cup test. Jet cup attrition experiments are commonly used for bulk attrition testing of fluidized bed catalyst. The results indicate that the particle attrition in the jet cup cold flow experiments arises from surface abrasion due to particle-particle and particle-wall interactions. Experiments indicate that the measured cumulative mass loss increases with attrition time. However, the attrition rate decreases sharply at the early stage of attrition, and gradually, the rate decline slows and approaches a constant value with increasing attrition time. Furthermore, the influence of inlet gas velocity and solid inventory is discussed. As inlet gas velocities increase, the measured cumulative mass loss also increases. However, as the solid inventory increases, the cumulative mass loss decreases. The results also show that the jet cup experiments quantitatively compare with low magnitude tangential forces which is an indication of attrition through abrasion as the primary mechanism. It is determined through particle size distributions before and after which show a small shift of the main peaks with no peak broadening while producing a small number of fines. By using the mass of abraded fines and the widely-used Archard model for abrasive attrition, the specific wear rate coefficient can be predicted as a function of time. The wear coefficient calculation further identifies that the abrasion mechanism as the primary mechanism of attrition.

42 ENGINEERING↗

Device-scale computational fluid dynamics modeling of carbon dioxide absorption using encapsulated sorbents

Micro-encapsulated carbon dioxide sorbent (MECS) is considered to be a promising material for carbon capture system because of high capture rate, low fabrication cost, and efficient energy consumption. To accelerate the development of MECS technology for industrial deployment, device-scale computational fluid dynamics (CFD) simulations are performed to study hydrodynamics and CO2 absorption behavior in a conceptual fluidized bed reactor. The two-fluid model solver, built in the Multiphase Flow with Interphase eXchanges (MFIX), is adopted to solve the multiphase flow hydrodynamics by representing both fluid and solids as continuous phases. Filtered models are implemented to capture the sub-grid effects that normally cannot be directly considered because MECS particles are too small to be explicitly resolved at such a large scale. Using established CFD tools, this study aims to characterize MECS behavior and predict its carbon capture performance in a conceptual device-scale absorber. The MECS particle size and gas flow rate have significant impact on CO2 capture efficiency. The CO2 capture efficiency decreases with increasing gas flow rate. Smaller particle size lead to better gas-solid homogeneity, as a results CO2 absorption efficiency increases.

Wang, Chao (ORCID:0000000279406614)↗

An error-controlled adaptive time-stepping method for particle advancement in coupled CFD-DEM simulations

Coupled Computational-Fluid-Dynamics (CFD) and Discrete-Element-Method (DEM) models provide an accurate description of multiphase physical systems where a solid granular particle phase exists in an underlying gaseous continuous medium. The time integration of the granular phase in these simulations is typically handled using an explicit scheme with a constant time-step among all particles that is invariant in time to resolve inter-particle collisions. A locally third-order accurate adaptive time integration technique for particles that employs an embedded locally second-order scheme for error determination is presented in this work. The particle time-step size is dynamically adapted based on solution error, thus leading to significant savings in computational time. The efficacy of our scheme is quantified using four test cases of varying complexity (binary collision, homogeneous cooling system, fluidized bed and hopper discharge). The adaptive time-stepping method exhibits improved performance (~ 2–3 times in most of the cases studied) compared to three commonly used non-adaptive time-step methods (first-order Euler-explicit, second-order Adams-Bashforth and third-order Runge-Kutta schemes), while maintaining the same level of accuracy and parallel scalability.

42 ENGINEERING↗

Multi-fidelity kinetic theory-based approach for the prediction of particle attrition: Application to jet cup attrition system

The timescale difference between the “fast” flow dynamics of fluidized bed reactors and the relatively “slow” rate of particle degradation makes the direct computational prediction of attrition challenging. An approach to this challenge is a multi-fidelity strategy where a high fidelity model for the flow dynamics is coupled with a lower fidelity model for the long-time resolution of the bulk attrition of the reactor inventory. We implement this approach using high-fidelity kinetic theory simulations to calculate the flow dynamics which are post-processed to calculate the frequency and intensity of the particle-particle and particle-wall collisions (e.g. collision energy spectra). This is combined with the particle breakage properties to construct the coefficients for a low-fidelity model [e.g. Monazam et al., 2018, Powder Technology 340, p. 528-536]. Simulations are performed of a jet cup attrition system containing Canadian hematite (Monazam et al. 2018). Furthermore, these are first analyzed using the collision energy spectra. Quantitative predictions of the mass loss are made using a low-fidelity model derived from the collision-spectra and a calibrated material breakage coefficient. The results are found to compare favorably with the experimental measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Study the thermal radiation effects in gas-solid flows with gray and non-gray P1 models implemented in MFiX

Thermal radiation is a dominant mode of heat transfer in combustion/gasification, packed/circulating bed reactors, and energy storage/conversion devices. In hydrocarbon fuel combustion, the high absorption and emission of product gases like CO 2 and H 2 O significantly affect the heat transfer characteristics. It is essential to understand the radiative energy propagation in such applications. In the present study, we developed a framework to implement the P-1 radiation model in MFiX for Eulerian-Eulerian (Two fluid-TFM) and Eulerian-Lagrangian (Discrete element-DEM and Particle in cell-PIC) models. The P-1 is a simplification of the spherical harmonics method. The framework has been verified on various flue gas conditions. The verified solver results are validated against the benchmark results available in the literature. The verified and validated gray and non-gray weighted sum of gray gas models is evaluated for dry and wet flue gas conditions. Further, they are also used to study gas-solid flows in a fluidized bed/riser.

20 FOSSIL-FUELED POWER PLANTS↗

Advances in central receivers for concentrating solar applications

This paper provides a review of current state-of-the-art commercial central receiver systems and emerging technologies intended to increase the outlet temperature to >700 °C. Research on particle-based, gas-based, and liquid-based receiver designs that can achieve these higher temperatures are discussed. Particle-based technologies include directly irradiated designs (free-falling, obstructed, centrifugal) and enclosed designs (gravity fed, fluidized). New gas-based receivers include micro-channel designs and light-trapping configurations that increase the surface area, heat transfer, and solar absorptance to enable higher fluxes and pressures. Liquid-based receivers and materials that are reviewed include high-temperature halide salts (chlorides and fluorides), carbonate salts, and liquid metals (sodium and lead bismuth). Advantages and challenges associated with each of the technologies and receiver designs are presented.

14 SOLAR ENERGY↗

Thermomechanical analysis and modeling of a high-temperature light trapping planar cavity solar receiver

The development of durable particle-based high-temperature solar receivers is critical for advancing concentrating solar-thermal (CST) technologies to enable high-efficiency power generation and industrial process heat. Here, this study presents a computational framework to evaluate the thermomechanical performance of a proposed enclosed light-trapping planar cavity receiver designed for particle-based thermal energy systems. The receiver incorporates absorptive cavities and fluidized particle-bed channels to enhance heat capture and reduce thermal losses. Finite element analysis (FEA) is employed to assess stress, strain, and creep-fatigue behavior under concentrated solar flux using realistic thermal boundary conditions derived from coupled system models and experimental assembly parameters. The analysis investigates the influence of particle-to-wall heat transfer coefficients (HTC) ranging from 800 to 1800 W/m 2 .K on the thermomechanical response of six candidate high-temperature alloys: Alloy 740H, Alloy 282, Alloy 617, 316H, Alloy 230, and 800H. Results show that increasing HTC reduces thermal gradients, leading to lower stresses and strains and extended minimum predicted creep life. While all materials satisfy fatigue life requirements under the investigated conditions, significant differences in creep resistance are observed. Alloy 740H consistently exhibits the longest minimum predicted creep life and the most favorable durability margins, followed by Alloy 282, with the remaining materials showing reduced creep resistance under identical loading. The reported creep lives are conservative lower-bound estimates intended for comparative material evaluation. This framework highlights the critical roles of material selection and geometry optimization in improving mechanical durability and reliability of solar-thermal receivers, forming a foundation for future experimental validation and design optimization.

14 SOLAR ENERGY↗

Process and technological aspects of municipal solid waste gasification. A review

Highlights: Black-Right-Pointing-Pointer Critical assessment of the main commercially available MSW gasifiers. Black-Right-Pointing-Pointer Detailed discussion of the basic features of gasification process. Black-Right-Pointing-Pointer Description of configurations of gasification-based waste-to-energy units. Black-Right-Pointing-Pointer Environmental performance analysis, on the basis of independent sources data. - Abstract: The paper proposes a critical assessment of municipal solid waste gasification today, starting from basic aspects of the process (process types and steps, operating and performance parameters) and arriving to a comparative analysis of the reactors (fixed bed, fluidized bed, entrained bed, vertical shaft, moving grate furnace, rotary kiln, plasma reactor) as well as of the possible plant configurations (heat gasifier and power gasifier) and the environmental performances of the main commercially available gasifiers for municipal solid wastes. The analysis indicates that gasification is a technically viable option for the solid waste conversion, including residual waste from separate collection of municipal solid waste. It is able to meet existing emission limits and can have a remarkable effect on reduction of landfill disposal option.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Increasing pyrolysis oil yields and decreasing energy consumption via thermal oxo-degradation of polyolefins

Commercialization of pyrolysis of plastics in an inert atmosphere is challenging due to large thermal requirements. This study employs thermal oxo-degradation and demonstrates how oxygen supplied at modest equivalence ratios can both accelerate depolymerization and provide the enthalpy for pyrolysis without dramatically impacting desired product yields. The enthalpies for pyrolysis of high-density polyethylene (HDPE) and polypropylene (PP) are measured to be 2,300 ± 90 J g – -1 and 2,800 ± 60 J g –1 , respectively. Using air as an oxygen source in a fluidized bed reactor, HDPE and PP are rapidly deconstructed while using up to 84% less energy through the energy released by partial oxidation. Characterization of the thermal oxo-degradation product oil shows comparable composition to conventional pyrolysis oil. Thermal oxo-degradation proves to be a promising technology for upcycling of plastics by improving thermal depolymerization of waste plastics and reducing energy requirements while maintaining desirable yields.

42 ENGINEERING↗

Clustering instabilities in sedimenting fluid–solid systems: critical assessment of kinetic-theory-based predictions using direct numerical simulation data

In this paper the quantitative and qualitative ability of a kinetic-theory-based two-fluid model (KT-TFM) is assessed in a state of fully periodic sedimentation (fluidization), with a focus on statistically steady, unstable (clustered) states. The accuracy of KT-TFM predictions is evaluated via direct comparison to direct numerical simulation (DNS) data. The KT-TFM and DNS results span a rather wide parameter space: mean-flow Reynolds numbers on the order of 1 and 10, mean solid volume fractions from 0.1 to 0.4, solid-to-fluid density ratios from 10 to 1000 and elastic and moderately inelastic (restitution coefficient of 0.9) conditions. Data from both KT-TFM and DNS display a rich variety of statistically steady yet unstable structures (clusters). Instantaneous snapshots of KT-TFM and DNS demonstrate remarkable qualitative agreement. This qualitative agreement is quantified by calculating the critical density ratio at which the structure transitions from a chaotic, dynamic state to a regular, plug-flow state, with good overall comparisons. Further quantitative assessments of mean and fluctuating velocities show good agreement at high density ratios but weaker agreement at intermediate to low density ratios depending on the mean-flow Reynolds numbers and solid fractions. Deviations of the KT-TFM results from the DNS data were traced to a breakdown in one of the underlying assumptions of the kinetic theory derivation: high thermal Stokes number. Surprisingly, however, even though the low Knudsen number assumption, also associated with the kinetic theory derivation, is violated throughout most of the parameter space, it does not seem to affect the good quantitative accuracy of KT-TFM simulations.

42 ENGINEERING↗

Insights into Mechanisms of Screw Feeder Plugging by Heated Pine Forestry Residues Using in-situ and Correlative Microscopy

Increasing concerns about global carbon emissions due to fossil fuel use has created interest in renewable fuel alternatives, such as lignocellulosic biomass. With an estimated global biomass production probability ten-fold higher than projected need, functionalizing and scaling biomass conversion processes, like pyrolysis, is a promising component of a diverse sustainable energy program (Kan, Strezov, & Evans, 2016). Pyrolysis reactors employed in biomass conversion often encounter the known problem of screw feeder plugging, halting work and reducing efficiency of biorefineries. Although the screw feeder is not heated directly, conductive heat transfer from the fluidized bed pyrolysis reactor creates a temperature gradient, where particles experience temperatures between 22°C and 500°C from the time they enter the feeder to being emptied into the reactor (Digman, Joo, & Kim, 2009; Nieminen & Folke, 1982). The impact of unintentional heating on this highly variable feedstock may result in particle morphology modification, surface texture transformation, and the evolution of viscous compounds and may contribute to screw feeder plugging (Haas, Nimlos, & Donohoe, 2009; Ingram et al., 2008). We hypothesized that particles of various anatomical fractions (including needles, branches, bark, cambium, and whitewood) will experience dramatic changes during this heating regime, which will be characterized by decreased particle size, increased surface roughness, degradation of key structural macromolecules, and generation of viscous compounds that would result in increased particle friction and cohesion, contributing to screw feeder plugging.

biofuels↗

Global Gas-Phase Oxidation Rates of Select Products from the Fast Pyrolysis of Lignocellulose

The oxidation kinetics for products of fast pyrolysis at low temperatures (<600°C) are not well known. These will be important in effort to model autothermal pyrolysis, which has been recently developed to intensify the process, but which occurs at much lower temperatures than combustion. Furthermore, this study determines global oxidation rates at 400-600°C for three important products of fast pyrolysis: levoglucosan, xylose, and acetic acid. Experiments were performed in a fluidized bed pyrolyzer with the reactor modeled as a series of CSTRs and PFRs to determine reaction rates. Oxidation rates at 500°C for the three model compounds varied by a factor of ten.

09 BIOMASS FUELS↗

Perspectives on Polyolefin Catalysis in Microfluidics for High-Throughput Screening: A Minireview

Polyolefins are the largest produced plastics in the world which traditionally employ continuous stirred tank reactors and fluidized bed reactors for commercial production. The operating condition, reaction kinetics, and molecular interactions inside the reactor strongly affect the polyolefin properties, which require stringent process control in conventional procedures. Understanding the catalytic pathway, behavior of polymer particles and effect of reactor conditions are essential for designing specific polymer properties, namely the molecular weight, chain length, polydispersity, etc. Microfluidics can play a significant role in designing polymers tailored to the user needs. Smaller channel dimensions help obtain uniform reaction conditions over the length of the microfluidic reactor in a controlled environment. With real-time monitoring techniques in microfluidics, even single particle growth of polymer can be studied to understand the parameters affecting the polymer properties. High throughput microfluidics can help catalyst screening in a short duration with less consumption of reagents generating less waste. When supplemented with efficient machine learning algorithms, automated high throughput microfluidics has the potential to rapidly optimize the process and develop new knowledge even with a limited data set. When trained on data sets generated using microfluidic experiments that are designed efficiently with working knowledge of the process, machine learning algorithms can provide the relationship between the multivariable parameters space and polymer properties, which is not possible with the traditional statistical methods and interpolation techniques. Here, the rise in the utilization of microfluidics, with the advancement of machine learning algorithms, for polyolefin catalysis, highlights the importance of microfluidics for catalyst discovery, parameter optimization, and understanding reaction pathway for producing polymers with specific properties for specialized applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Refinery Perspective on Decarbonizing with Marine Biofuels

This work seeks to understand what biofuel production pathways a refinery might prefer to produce very low sulfur fuel oil (VLSFO) for marine applications. A comprehensive refinery optimization model was modified to allow for (1) direct blending of soy biodiesel, renewable diesel, Fischer-Tropsch diesel, and several pyrolysis oils and (2) indirect blending of all pyrolysis oils via co-processing in a fluidized catalytic cracker (FCC) and diesel hydrotreater into the marine fuel pool. Results showed that preferred pathways to bio-VLSFO production included co-processing low-quality pyrolysis oil in a FCC to blend the resulting biogenic light cycle oil, directly blending soy biodiesel, and directly blending small quantities of pyrolysis oil. Bio-VLSFO production costs were compared to those of fossil VLSFO subject to different marine fuel demands, benchmark crude oil prices, and biogenic fractions in the finished product. Given benchmark crude oil prices over 60 $/bbl, bio-VLSFO production appeared to be significantly cheaper than fossil VLSFO. Corresponding marginal abatement costs of CO 2 mostly ranging from -300 to 350 $/ton of CO 2 were also determined using a simplified but novel approach to allow for a comparison to other decarbonization strategies. In conclusion, this work indicates that low-sulfur contents in biofuels, relatively relaxed specifications for marine fuels, and current difficulties in meeting VLSFO specifications with crude oils can combine to make bio-VLSFO production cost-effective. Moreover, marine fuels appear to be a good entry point for refiners to start decarbonizing with biofuel pathways that could eventually be extended to other product pools.

09 BIOMASS FUELS↗

Catalytic Upgrading of Pyrolysis Condensables from Postconsumer Polyolefins Using HZSM-5

The conversion of plastic wastes to monomeric olefins is an attractive means for achieving a plastic circular economy. In our study, a fluidized bed reactor converts post-consumer waste high-density polyethylene (HDPE) and polypropylene (PP) to mostly condensed pyrolysis waxes and some oils, preventing carbon loss to gases. The pyrolysis condensables were upgraded to light olefins (C 2 –C 5 ) at carbon yields greater than 76 wt % using the HZSM-5 zeolite catalyst at a post pyrolysis process that employed a micropyrolyzer. These results were comparable to olefin monomer yields from direct ex situ catalytic pyrolysis of the original waste plastics without condensing the vapors, highlighting the potential applicability of this approach in plastic waste recycling. Our results suggest that a centralized catalytic upgrading facility fed by pyrolysis condensables sourced from distributed thermochemical processing plants is a promising pathway to a circular economy. Such an approach enables utilization of available catalytic cracking infrastructure while focusing on setting up distributed thermochemical processing plants close to material recovery facilities. As a result, the energy-dense pyrolysis waxes are more suitable for transportation, contributing to the overall scalability and economic viability of the proposed distributed approach.

10 SYNTHETIC FUELS↗

Evaluation of Biomass-Derived Distillate Fuel as Renewable Heating Oil

The utilization of advanced biofuels in stationary applications, such as home heating, is considered as an early entry point for biomass-derived fuels into the distillate fuel market sector. Two renewable fuels produced by a biomass fluidized catalytic cracking (BFCC) process, followed by hydroprocessing and fractionation, were tested. The evaluation was performed on a pure (100%) distillate fraction, 50% blend of the distillate fraction with petroleum-based heating oil, and 20% blend of a heavier gas oil fraction. Combustion experiments were carried out in a transparent quartz chamber and a typical oil-fired residential boiler. The flame stability, size, and shape produced by the fuels were examined. The flue gas was analyzed for O 2 , CO, NO x , and smoke. The elastomer compatibility test was performed with nitrile slabs at 43 °C for 1 month. Fuel stability was examined at 80 °C for 1 week. The results from the combustion studies suggest that the distillate fuel blends could be used as alternative fuels to No. 2 heating oil, even up to 100% without any operational issues. The distillate fuels were found to be stable. and the nitrile slab volume swell (~10%) suggests that the fuel could be compatible to legacy elastomers.

09 BIOMASS FUELS↗

Thermal Oxo-degradation and Catalytic Upgrading of Plastic Waste to Light Olefins for a Circular Economy

The commercialization of conventional pyrolysis of plastic in an inert atmosphere has been hindered by large thermal requirements stemming from long reaction rates. The rate of thermal depolymerization of waste plastics can be accelerated by the addition of oxygen in a process known as thermal oxo-degradation (TOD). This study offers the prospect of TOD to upcycle postconsumer waste rapidly and efficiently. Using moderate temperatures and small amounts of air in a fluidized bed reactor, we demonstrated that waste high-density polyethylene and polypropylene are rapidly deconstructed to condensable products. These condensable products were catalytically upgraded in a micropyrolysis reactor using commercially available zeolite (HZSM-5) to monomeric olefins. The olefin yields proved to be greater than those achieved through the catalytic upgrading of condensable products from (nonoxidative) the pyrolysis of the same plastic wastes. The coupling of TOD with catalytic upgrading proves to be an energy-efficient pathway in a plastics circular economy for the production of light olefins from wastes.

Enthalpy↗

Thermal Stability of Fractionated Bio-Oil from Fast Pyrolysis

A method was developed to simulate the rapid heating bio-oil fractions will undergo if upgraded using conventional petroleum refining processes. Bio-oil fractions were produced via fluidized bed fast pyrolysis of southern yellow pine sawmill residue. Thermal processing of the bio-oil fractions was evaluated at three temperatures (100, 200, and 300 °C) and two heating times (60 and 120 s). Thermal stability was defined as the increase in average relative molecular weight (RMW) of bio-oil samples after thermal treatment. The effect of moisture content and total acid number (TAN) on thermal stability was also investigated. Changes in chemical structures were observed via Fourier transform infrared spectroscopy (FTIR). Bio-oil fractions exhibited considerable instability at temperatures above 100 °C with substantial increases in average RMW for both 60 and 120 s heating times. Finally, the initial concentration of acids, as measured by TAN and ion chromatography (IC), was found to be the strongest predictor of thermal instability.

09 BIOMASS FUELS↗