Search NASA⌕ Search

SEARCH · Search NASA

Results for “INDUCTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Planning Optimization for Inductively Charged On-demand Automated Electric Shuttles Project at Greenville, South Carolina

Wireless charging technology presents an ideal fit for autonomous electric vehicles for realizing a fully automated system (vehicle and charger). This paper presents a planning optimization analysis for a pilot project of in-route wireless charging infrastructure serving fixed-route on-demand shared automated electric shuttles (SAESs) at Greenville, South Carolina, USA. A single-objective non-linear mixed integer system planning optimization problem is formulated. A comprehensive cost model representing the overall inductively charged SAESs system is developed, considering road construction, power electronics and materials, traction battery, and installation costs. The optimization problem is solved to determine the best combination of the system key design parameters (number and allocations of wireless chargers, charging power level, track length and on-board battery capacity) that show the most cost-effective solution and allow the SAESs to achieve charge-sustaining operation. The planning platform incorporates representative simulated traffic data (driving speed and routes) for four SAESs in the Greenville using the Simulation of Urban Mobility tool. These data are fed to a vehicle powertrain model and a wireless charger power model to predict the battery power, energy and state-of-charge profiles, which are provided to the search algorithm to assess the design objectives under specific constraints. Finally, the results indicate that implementing high-power (100 kW) wireless charger at a few designated stops for fixed-route SAESs with the proper track length allows the vehicles to realize charge-sustaining operation, infinite range, and zero recharge downtime, with a significant reduction in the on-board battery (36%) and road coverage (69%), at minimum cost.

33 ADVANCED PROPULSION SYSTEMS↗

Beam Envelope Stability in an Advanced Linear Induction Accelerator

A new linear induction accelerator (LIA) is under development for multipulse flash radiography. Because it has substantially more cells than present LIAs, higher magnetic focusing fields are needed to suppress beam breakup (BBU). It is, therefore, more susceptible to the parametric beam envelope instability (PEI), which has an instability threshold that has usually been typified by the vacuum phase advance per cell exceeding some large fraction of π . Here we derive a threshold criterion for PEI that depends not only on the magnetic field, but also on the beam space charge and emittance. A tune designed to suppress BBU in Scorpius is shown to be stable to the PEI according to this criterion, and also by the lack of emittance growth in particle-in-cell (PIC) code simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electron-Beam Corkscrew Motion in an Advanced Linear Induction Accelerator

Scorpius is a multipulse linear induction accelerator (LIA) under development for flash radiography. Because it has substantially more cells than present LIAs, higher magnetic focusing fields are needed to suppress beam breakup (BBU). Therefore, it is more susceptible to corkscrew motion of the beam, which also depends on beam energy spread and focusing magnet misalignments. For energy spread and alignment tolerances expected for Scorpius, a magnetic tune designed to suppress BBU is shown to produce corkscrew motion within the range that can be controlled through the use of steering dipoles on existing LIAs. Finally, a gap-voltage modulation scheme is shown to almost completely eliminate chromatic effects such as corkscrew.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Frequency Control Support of a Doubly-Fed Induction Generator Based on the Torque Limit

This paper proposes a torque limit-based inertial control scheme of a doubly-fed induction generator (DFIG) that supports the frequency control of a power system. If a frequency deviation occurs, the proposed scheme aims to release a large amount of kinetic energy (KE) stored in the rotating masses of a DFIG to raise the frequency nadir (FN). Upon detecting the event, the scheme instantly increases its output to the torque limit and then reduces the output with the rotor speed so that it converges to the stable operating range. To restore the rotor speed while causing a small second frequency dip (SFD), after the rotor speed converges the power reference is reduced by a small amount and maintained until it meets the reference for maximum power point tracking control. The test results demonstrate that the scheme can improve the FN and maximum rate of change of frequency while causing a small SFD in any wind conditions and in a power system that has a high penetration of wind power, and thus the scheme helps maintain the required level of system reliability. The scheme releases the KE from 2.9 times to 3.7 times the Hydro-Quebec requirement depending on the power reference.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Stable Adaptive Inertial Control of a Doubly-Fed Induction Generator

This paper proposes a stable adaptive inertial control scheme of a doubly-fed induction generator. The proposed power reference is defined in two sections: the deceleration period and the acceleration period. The power reference in the deceleration period consists of a constant and the reference for maximum power point tracking (MPPT) operation. The latter contributes to preventing a second frequency dip (SFD) in this period because its reduction rate is large at the early stage of an event but quickly decreases with time. To improve the frequency nadir (FN), the constant value is set to be proportional to the rotor speed prior to an event. The reference ensures that the rotor speed converges to a stable operating region. To accelerate the rotor speed while causing a small SFD, when the rotor speed converges, the power reference is reduced by a small amount and maintained until it meets the MPPT reference. The results show that the scheme causes a small SFD while improving the FN and the rate of change of frequency in any wind conditions, even in a grid that has a high penetration of wind power.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Dynamic Droop–Based Inertial Control of a Doubly-Fed Induction Generator

If a large disturbance occurs in a power grid, two auxiliary loops for the inertial control of a wind turbine generator have been used: droop loop and rate of change of frequency (ROCOF) loop. Because their gains are fixed, difficulties arise in determining them suitable for all grid and wind conditions. This paper proposes a dynamic droop-based inertial control scheme of a doubly-fed induction generator (DFIG). The scheme aims to improve the frequency nadir (FN) and ensure stable operation of a DFIG. To achieve the first goal, the scheme uses a droop loop, but it dynamically changes its gain based on the ROCOF to release a large amount of kinetic energy during the initial stage of a disturbance. To do this, a shaping function that relates the droop to the ROCOF is used. To achieve the second goal, different shaping functions, which depend on rotor speeds, are used to give a large contribution in high wind conditions and prevent over-deceleration in low wind conditions during inertial control. The performance of the proposed scheme was investigated under various wind conditions using an EMTP-RV simulator. The results indicate that the scheme improves the FN and ensures stable operation of a DFIG.

17 WIND ENERGY↗

Self-Resonant Coil Design for High-frequency High-Power Inductive Wireless Power Transfer

In this paper, the design methodology of a high-frequency, high-power, long-distance inductive wireless power transfer (WPT) is presented. The airgap (d) of a traditional high-power (>1 kW) WPT is limited to a few hundred millimeters, which is almost 1/4th of the coil diameter, D; d ≤ D/4. In this paper, the power transfer distance is significantly increased (d ≥ 1.5D) by adopting a high-frequency magnetic design and GaN-based power electronics. The material and design of the coil and shield are investigated using FEA and tested experimentally. A high frequency 6.78 MHz wireless charging system was built to transfer 1 kW power over 3 m airgap.

Mohammad, Mostak↗

Cold acclimation threshold induction temperatures of switchgrass ecotypes grown under a long and short photoperiod

Abstract Plants can cold acclimate to enhance their freezing tolerance by sensing declining temperature and photoperiod cues. However, the factors influencing genotypic variation in the induction of cold acclimation are poorly understood among perennial grasses. We hypothesized that the more northern upland switchgrass ( Panicum virgatum L.) ecotype develops a higher degree of freezing tolerance by initiating cold acclimation at higher temperatures as compared with the coastal and southern lowland ecotypes. First, we determined the optimal method for assessing freezing tolerance and the length of exposure to 8/4°C required to induce the maximum level of freezing tolerance in the most northern upland and most southern lowland genotypes. We characterized the maximum freezing tolerance of eight uplands, three coastal and five lowland genotypes grown for 21 days at 8/4°C and a 10 or 16 h photoperiod. Next, we identified the temperature required to induce cold acclimation by exposing the 16 genotypes for 7 days at 20–6°C constant temperatures under a 10 or 16 h photoperiod. Cold acclimation initiated at temperatures 5 and 7°C higher in upland than in coastal and lowland genotypes. Among upland genotypes the shorter photoperiod induced cold acclimation at a 1°C higher temperature. Genotypes originating from a more northern latitude initiate cold acclimation at higher temperatures and develop higher maximum freezing tolerances. An earlier response to declining temperatures may provide the upland ecotype with additional time to prepare for winter and provide an advantage when plants are subjected to the rapid changes in fall temperature associated with injurious frosts.

60 APPLIED LIFE SCIENCES↗

Investigation of processing advanced waste forms in Cold Crucible Induction Melter systems

The Cold Crucible Induction Melter (CCIM) technology has been identified in several independent reviews and studies as a potential alternative or supplemental vitrification technology for specific U.S. Department of Energy (DOE) high level radioactive waste (HLW) streams. These inventories have unique chemistries, such as high alumina, high iron, high chromium, etc., that are not amenable to efficient immobilization in conventional borosilicate glass (BSG) matrices. Advanced waste forms, such as iron phosphate glass (FePG), high crystalline BSG (HC-BSG), and alumino-silicate glass-ceramic (GC) have been shown to provide significantly improved immobilization matrices for these challenging waste streams, including dramatically improved waste loadings; however, they are difficult to efficiently process in the baseline joule-heated ceramic melters (JHCMs). The CCIM technology can effectively process these advanced waste forms at the desired high waste loadings. This paper describes the most recent collaborative activities between the DOE Office of Environmental Management (DOE EM) and various Russian institutions in modeling, development and testing of advanced waste forms in CCIMs, including FePG and HC-BSG formulations. Additionally, past interactions with other international partners, including France and Korea, are described. Finally, recent enhancements to CCIM processing related to modeling, draining techniques and automated control, which were collaboratively developed, will be discussed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Ultra-trace determination of Strontium-90 in environmental soil samples from Qatar by collision/reaction cell-inductively coupled plasma mass spectrometry (CRC-ICP-MS/MS)

Because of the very low level of {sup 90}Sr in the environmental soil samples and its determination by beta counting may take several weeks, we developed a procedure for ultra-trace determination of {sup 90}Sr using collision reaction cell-inductively coupled plasma tandem mass spectrometry (CRC-ICP-MS/MS, Agilent 8800). Soil samples were dried at 105 deg. C and then heated in a furnace at 550 deg. C to remove any organics present. 500 g of each soil samples were aliquoted into 2000 ml glass beakers. Each Soils samples were soaked in 2 ppm Sr solution carrier to allow determination of chemical yield. The solid to liquid ratio was 1:1. Finally the soil samples were dried at 105 deg. C. Five hundred milliliters concentrated nitric acid and 250 ml hydrochloric acid volumes were added on 500 g soil samples. The samples were digested on hot plate at 80 deg. C to prevent spraying with continuous manual mixing. The leachate solution was separated. The solids were rinsed with 500 ml deionized water, warmed on a hot plate and the leachate plus previous leachate were filtered and the total volume was reduced to 500 ml by evaporation. Final leachate volume was transferred to a centrifuge tubes. The centrifuge tubes were centrifuged at 3,500 rpm for 10 min. The leachate was transferred to a 1 L beaker and heated on a hot plate to evaporate the leachate to dryness. The reside was re-dissolved in 100 ml of 2% HNO{sub 3} and reduced by evaporation to 10 mL. The solution was measured directly by CRC-ICP-MS/MS by setting the first quadruple analyzer to m/z 90 and introducing oxygen gas into the reaction cell for elimination isobar interference from zirconium-90. The method was validated by measurements of standard reference materials and applied on environmental soil samples. The overall time requirement for the measurement of strontium-90 by CRC-ICP-MS/MS is 2 days, significantly shorter than any radioanalytical protocol currently available. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Surface characterization of hydrophobic thin films deposited by inductively coupled and pulsed plasmas

Different fluorocarbon thin films were deposited on Si substrates using a plasma-polymerization method. Fluorine-containing hydrophobic thin films were obtained by inductively coupled plasma (ICP) and pulsed plasma (PP) with a mixture of fluorocarbon precursors C{sub 2}F{sub 6}, C{sub 3}F{sub 8}, and c-C{sub 4}F{sub 8} and the unsaturated hydrocarbons of C{sub 2}H{sub 2}. The influence on the fluorocarbon surfaces of the process parameters for plasma polymerization, including the gas ratio and the plasma power, were investigated under two plasma-polymerized techniques with different fluorocarbon gas precursors. The hydrophobic properties, surface morphologies, and chemical compositions were elucidated using water contact angle measurements, field emission-scanning electron microscope, x-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), and time-of-flight secondary ion mass spectrometry (TOF-SIMS). In this study, the ICP technique provides coarser grained films and more hydrophobic surfaces as well as a higher deposition rate compared to the PP technique. XPS, FT-IR, and TOF-SIMS analyses indicated that the ICP technique produced more fluorine-related functional groups, including CF{sub 2} and CF{sub 3}, on the surface. From the curve-fitted XPS results, fluorocarbon films grown under ICP technique exhibited less degree of cross-linking and higher CF{sub 2} concentrations than those grown under PP technique.

36 MATERIALS SCIENCE↗

Inductively coupled plasma-reactive ion etching of InSb using CH{sub 4}/H{sub 2}/Ar plasma

InSb is an important material for optoelectronic devices. Most InSb devices are currently wet etched, and the etching geometries are limited due to the isotropic nature of wet etching. Inductively coupled plasma (ICP)-reactive ion etching (RIE) is a more desirable alternative because it offers a means of producing small anisotropic structures especially needed in large format infrared focal plane arrays. This work describes the novel use of ICP-RIE for fabricating InSb mesas with CH{sub 4}/H{sub 2}/Ar plasma and presents the influences of the process parameters on the etch rate and surface morphology. The parameters investigated include bias radio frequency power (50-250 W), %CH{sub 4} in H{sub 2} (10-50), argon (Ar) partial pressure (0-0.3 Pa with total pressure of 1.0 Pa), and total pressure (0.35-4 Pa). With the process parameters optimized in this investigated ranges, good etching results have been achieved with etch rates up to 80 nm/min, and etch features with sidewall angles of about 80 degree sign , the etched surface is as smooth as before the RIE process.

36 MATERIALS SCIENCE↗

Effect of Ar and N{sub 2} addition on CH{sub 4}-H{sub 2} based chemistry inductively coupled plasma etching of HgCdTe

Mercury cadmium telluride (MCT) CH{sub 4}-H{sub 2} based chemistry inductively coupled plasma (ICP) etching mechanisms are investigated. The effect of Ar and N{sub 2} addition in the mixture on plasma and MCT surface characteristics are studied by Langmuir probe, mass spectrometry, and x-ray photoelectron spectroscopy (XPS). In the authors' conditions, the HgTe faster removal than CdTe leads to the formation of a CdTe rich layer in the first 30 s of plasma exposure. Ion flux intensity and composition are only slightly influenced by N{sub 2} addition while a strong effect is shown on neutral species by the formation of NH{sub 3}, HCN, and the increase in CH{sub 3} radical density. At the opposite, Ar addition to the gas mixture leads to a total ion flux increase and promote CH{sub 3}{sup +} formation while small changes are observed on neutral species. In our low pressure and high density conditions, same order of magnitude of ion and neutral CH{sub 3} flux on MCT surface is found, suggesting a chemical contribution of CH{sub 3}{sup +} ions in MCT etching. This is confirmed by a strong correlation of the MCT etching yield versus total (neutral and ionic) CH{sub 3} flux. These results suggest that the etching is limited by the supply of CH{sub 3} to the surface.

36 MATERIALS SCIENCE↗

Etching characteristics and mechanism of indium tin oxide films in an inductively coupled HBr/Ar plasma

The investigations of etch characteristics and mechanisms for indium tin oxide (In{sub 2}O{sub 3}){sub 0.9}:(SnO{sub 2}){sub 0.1} (ITO) thin films using HBr/Ar inductively coupled plasma were carried out. The ITO etch rate was measured in the range of 0%-100% Ar in the HBr/Ar mixture at fixed gas pressure (6 mTorr), input power (700 W), and bias power (200 W). Plasma parameters and composition were examined with a combination of plasma diagnostics by double Langmuir probe and global (zero-dimensional) plasma model. It was found that the ITO etch rate follows the behavior of Br atom flux but contradicts with that for H atoms and positive ions. This suggests that the ITO etch process is not limited by the ion-surface interaction kinetics and appears in the reaction-rate-limited etch regime with the Br atoms as the main chemically active species.

36 MATERIALS SCIENCE↗

''SensArray'' voltage sensor analysis in an inductively coupled plasma

A commercially manufactured PlasmaVolt sensor wafer was studied in an inductively coupled plasma reactor in an effort to validate sensor measurements. A pure Ar plasma at various powers (25-420 W), for a range of pressures (10-80 mT), and bias voltages (0-250 V) was utilized. A numerical sheath simulation was simultaneously developed in order to interpret experimental results. It was found that PlasmaVolt sensor measurements are proportional to the rf-current through the sheath. Under conditions such that the sheath impedance is dominantly capacitive, sensor measurements follow a scaling law derived from the inhomogeneous sheath model of Lieberman and Lichtenberg, [Principles of Plasma Discharges and Materials Processing (Wiley, New York, 2005)]. Under these conditions, sensor measurements are proportional to the square root of the plasma density at the plasma-sheath interface, the one-fourth root of the electron temperature, and the one-fourth root of the rf bias voltage. When the sheath impedance becomes increasingly resistive, the sensor measurements deviate from the scaling law and tend to be directly proportional to the plasma density. The measurements and numerical sheath simulation demonstrate the scaling behavior as a function of changing sheath impedance for various plasma conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fast and smooth etching of indium tin oxides in BCl{sub 3}/Cl{sub 2} inductively coupled plasmas

The etching characteristics of evaporation-deposited indium tin oxide (ITO) films in BCl{sub 3}/Cl{sub 2} inductively coupled plasmas have been studied. High etch rates >200 nm/min were obtained at large BCl{sub 3}/Cl{sub 2} gas flow ratios and high rf chuck powers, suggesting that the etching process is limited by sputter desorption of InCl{sub x} and SnCl{sub x} compounds. The addition of a small amount of CF{sub 4}, which acts as reducing agent, increased the etch rate by 30% and resulted in very smooth etched surfaces. It has also been found that the material crystallinity has a pronounced influence on ITO etch rate. ITO films annealed at 500 deg. C exhibited the maximum etch resistance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Etch mechanism of In{sub 2}O{sub 3} and SnO{sub 2} thin films in HBr-based inductively coupled plasmas

The investigations of etch characteristics and mechanisms for both In{sub 2}O{sub 3} and SnO{sub 2} thin films in the HBr-based inductively coupled plasmas were carried out. The etch rates were measured as functions of gas mixing ratio (0%-100% Ar), input power (400-700 W), and gas pressure (4-10 mTorr) at fixed bias power (200 W) and gas flow rate [40 SCCM (SCCM denotes cubic centimeter per minute at STP)]. Plasma parameters and composition were determined using a combination of plasma diagnostics by double Langmuir probe and global (zero-dimensional) plasma model. The correlations between the behaviors of etch rates and fluxes of plasma active species allow one to infer both In{sub 2}O{sub 3} and SnO{sub 2} etch mechanisms as the transitional regime of ion-assisted chemical reaction, which is controlled by neutral and charged fluxes together.

36 MATERIALS SCIENCE↗

Etching studies of silica glasses in SF{sub 6}/Ar inductively coupled plasmas: Implications for microfluidic devices fabrication

To fabricate microlaboratories, commercially available silica glasses represent a good alternative to the expensive quartz or fused silica substrates. Therefore, the authors have here investigated the behavior of four of them--Vycor, Pyrex, D263, and AF45--in SF{sub 6} and SF{sub 6}/Ar inductively coupled plasmas. Using Vycor, a material close to pure SiO{sub 2}, as a reference, they demonstrated that the etch rate negatively correlates with the global content in metallic oxides. However, no such clear trend was found for the surface roughness and they hypothesize that the large asperities (>500 nm) sometimes observed might be due to local variation in the glass surface composition. Furthermore, investigations on the influence of the plasma conditions (i.e., source power, dc self-bias, gas mixture, and pressure) on the etch rate, surface chemistry, and surface morphology, as well as positive ion current and fluorine concentration measurements, enable them to unravel an ion enhanced chemical etching mechanism, where stronger ion assistance is needed when more metallic oxides are present. By increasing the ion to neutral flux ratio, they consequently could, for all the materials, reduce the surface roughness to less than 5 nm while maintaining etch rates around 150 nm/min. These conditions have further been used to optimize pattern transfer experiments.

36 MATERIALS SCIENCE↗