Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mobile Measuring System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Refined Analysis of CO2 Emissions in Urban Air Mobility Networks

In this study, we examine the environmental impact of Urban Air Mobility (UAM) operations as measured via carbon dioxide (CO2) emissions by leveraging a computational model from previous studies that has been refined and expanded. Several scenarios are examined in which total transportation emissions for a representative day in a metro area are distributed differently among vehicle types and transportation modes. Specifically, we investigate the use of electric air vehicles in a UAM network; the increasing presence of electric ground vehicles for ground transportation; the impacts from implementing ridesharing in the UAM mode; and the effects of varying the electricity grid emissions. Results for a case study in the Chicago, IL metro area indicate that incorporating electric ground vehicles and UAM ridesharing can both lead to reduced CO2 emissions. These preliminary results indicate that carbon emissions from a UAM system leveraging ridesharing and all-electric aircraft may not be a practical operational limit on UAM, though further improvements to the modeling are warranted.

advanced air mobility↗

A HPLC method for the quantification of butyramide and acetamide at ppb levels in hydrogeothermal waters

A quantitative analytical method to determine butyramide and acetamide concentrations at the low ppb levels in geothermal waters has been developed. The analytes are concentrated in a preparation step by evaporation and analyzed using HPLC-UV. Chromatographic separation is achieved isocratically with a RP C-18 column using a 30 mM phosphate buffer solution with 5 mM heptane sulfonic acid and methanol (98:2 ratio) as the mobile phase. Absorbance is measured at 200 nm. The limit of detection (LOD) for BA and AA were 2.0 {mu}g L{sup -1} and 2.5 {mu}g L{sup -1}, respectively. The limit of quantification (LOQ) for BA and AA were 5.7 {mu}g L{sup -1} and 7.7 {mu}g L{sup -1}, respectively, at the detection wavelength of 200 nm. Attaining these levels of quantification better allows these amides to be used as thermally reactive tracers in low-temperature hydrogeothermal systems.

10 SYNTHETIC FUELS↗

Development of a 150-GHz MMIC Module Prototype for Large-Scale CMB Radiation

HEMT-based receiver arrays with excellent noise and scalability are already starting to be manufactured at 100 GHz, but the advances in technology should make it possible to develop receiver modules with even greater operation frequency up to 200 GHz. A prototype heterodyne amplifier module has been developed for operation from 140 to 170 GHz using monolithic millimeter-wave integrated circuit (MMIC) low-noise InP high electron mobility transistor (HEMT) amplifiers. The compact, scalable module is centered on the 150-GHz atmospheric window using components known to operate well at these frequencies. Arrays equipped with hundreds of these modules can be optimized for many different astrophysical measurement techniques, including spectroscopy and interferometry. This module is a heterodyne receiver module that is extremely compact, and makes use of 35-nm InP HEMT technology, and which has been shown to have excellent noise temperatures when cooled cryogenically to 30 K. This reduction in system noise over prior art has been demonstrated in commercial mixers (uncooled) at frequencies of 160-180 GHz. The module is expected to achieve a system noise temperature of 60 K when cooled. An MMIC amplifier module has been designed to demonstrate the feasibility of expanding heterodyne amplifier technology to the 140 to 170-GHz frequency range for astronomical observations. The miniaturization of many standard components and the refinement of RF interconnect technology have cleared the way to mass-production of heterodyne amplifier receivers, making it a feasible technology for many large-population arrays. This work furthers the recent research efforts in compact coherent receiver modules, including the development of the Q/U Imaging ExperimenT (QUIET) modules centered at 40 and 90 GHz, and the production of heterodyne module prototypes at 90 GHz.

Kangaslahti, Pekka P.↗

Atmospheric Radiation Measurement Program Climate Research Facility Operation quarterly report July 1 - September 30, 2010.

Individual raw datastreams from instrumentation at the Atmospheric Radiation Measurement (ARM) Climate Research Facility fixed and mobile sites are collected and sent to the Data Management Facility (DMF) at Pacific Northwest National Laboratory (PNNL) for processing in near real-time. Raw and processed data are then sent approximately daily to the ARM Archive, where they are made available to users. For each instrument, we calculate the ratio of the actual number of data records received daily at the Archive to the expected number of data records. The results are tabulated by (1) individual datastream, site, and month for the current year and (2) site and fiscal year (FY) dating back to 1998. The U.S. Department of Energy (DOE) requires national user facilities to report time-based operating data. The requirements concern the actual hours of operation (ACTUAL); the estimated maximum operation or uptime goal (OPSMAX), which accounts for planned downtime; and the VARIANCE [1-(ACTUAL/OPSMAX)], which accounts for unplanned downtime. The OPSMAX time for the fourth quarter of FY2010 for the Southern Great Plains (SGP) site is 2097.60 hours (0.95 2208 hours this quarter). The OPSMAX for the North Slope of Alaska (NSA) locale is 1987.20 hours (0.90 2208) and for the Tropical Western Pacific (TWP) locale is 1876.80 hours (0.85 2208). The first ARM Mobile Facility (AMF1) deployment in Graciosa Island, the Azores, Portugal, continues, so the OPSMAX time this quarter is 2097.60 hours (0.95 x 2208). The differences in OPSMAX performance reflect the complexity of local logistics and the frequency of extreme weather events. It is impractical to measure OPSMAX for each instrument or datastream. Data availability reported here refers to the average of the individual, continuous datastreams that have been received by the Archive. Data not at the Archive are caused by downtime (scheduled or unplanned) of the individual instruments. Therefore, data availability is directly related to individual instrument uptime. Thus, the average percentage of data in the Archive represents the average percentage of the time (24 hours per day, 92 days for this quarter) that the instruments were operating this quarter. Table 1 shows the accumulated maximum operation time (planned uptime), actual hours of operation, and variance (unplanned downtime) for the period July 1-September 30, 2010, for the fixed sites. Because the AMF operates episodically, the AMF statistics are reported separately and not included in the aggregate average with the fixed sites. This fourth quarter comprises a total of 2208 possible hours for the fixed and mobile sites. The average of the fixed sites exceeded our goal this quarter. The Site Access Request System is a web-based database used to track visitors to the fixed and mobile sites, all of which have facilities that can be visited. The NSA locale has the Barrow and Atqasuk sites. The SGP site has historically had a Central Facility, 23 extended facilities, 4 boundary facilities, and 3 intermediate facilities. Beginning in the second quarter of FY2010, the SGP began a transition to a smaller footprint (150 km x 150 km) by rearranging the original instrumentation and new instrumentation made available through the American Recovery and Reinvestment Act of 2009 (ARRA). The Central Facility and 4 extended facilities will remain, but there will be up to 12 new surface characterization facilities, 4 radar facilities, and 3 profiler facilities sited in the smaller domain. This new configuration will provide observations at scales more appropriate to current and future climate models. The transition to the smaller footprint is ongoing through this quarter. The TWP locale has the Manus, Nauru, and Darwin sites. These sites will also have expanded measurement capabilities with the addition of new instrumentation made available through ARRA funds. It is anticipated that the new instrumentation at all the fixed sites will be in place by the end of calendar year 2011. AMF1 continues its 20-month deployment in Graciosa Island, the Azores, Portugal, that began on May 1, 2009. The AMF will also have additional observational capabilities by the end of 2011. The second ARM Mobile Facility (AMF2) was deployed this quarter to Steamboat Springs, Colorado, in support of the Storm Peak Lab Cloud Property Validation Experiment (STORMVEX). The first field deployment of the second ARM Mobile Facility will be used to validate ARM-developed algorithms that convert the remote sensing measurements to cloud properties for liquid and mixed phase clouds. Although AMF2 is being set up this quarter, the official start date of the field campaign is not until November 1, 2010. This quarterly report provides the cumulative numbers of scientific user accounts by site for the period October 1, 2009-September 30, 2010.

54 ENVIRONMENTAL SCIENCES↗

Molecular shape and binding force of Mycoplasma mobile's leg protein Gli349 revealed by an AFM study

Recent studies of the gliding bacteria Mycoplasma mobile have identified a family of proteins called the Gli family which was considered to be involved in this novel and yet fairly unknown motility system. The 349 kDa protein called Gli349 was successfully isolated and purified from the bacteria, and electron microscopy imaging and antibody experiments led to the hypothesis that it acts as the 'leg' of M. mobile, responsible for attachment to the substrate as well as for gliding motility. However, more precise evidence of the molecular shape and function of this protein was required to asses this theory any further. In this study, an atomic force microscope (AFM) was used both as an imaging and a force measurement device to provide new information about Gli349 and its role in gliding motility. AFM images of the protein were obtained revealing a complex structure with both rigid and flexible parts, consistent with previous electron micrographs of the protein. Single-molecular force spectroscopy experiments were also performed, revealing that Gli349 is able to specifically bind to sialyllactose molecules and withstand unbinding forces around 70 pN. These findings strongly support the idea that Gli349 is the 'leg' protein of M. mobile, responsible for binding and also most probably force generation during gliding motility.

60 APPLIED LIFE SCIENCES↗

Evaluating the Ratio of Electron and Hole Mobilities from a Single Bulk Sample Using Photo-Seebeck Effect

When a semiconductor is under photoexcitation, the voltage response to a temperature gradient is the photo-Seebeck effect. In this work, we study this effect, focusing on the contribution from transport of photo-excited carriers. We demonstrate that by combining photo-Seebeck with photoconductivity measurements, one can determine the ratio between electron and hole mobilities, and hence both of them when one is known. This is found for the case of defect-free samples, where no detail on the absorbance, carrier lifetime or recombination is necessary. Our method reported here does not require chemical doping, which could introduce defects and is often not feasible. It applies to both thin film and bulk samples. Experiment wise, photo-Seebeck effect is relatively easy to implement, or added to existing systems. In a broader context, for semiconductors with significant influence from defects, our result suggests that the photo-Seebeck behavior can still be understood. In this case another photo-transport property is necessary, in order to identify the mobilities of carriers and information regarding the defects. This framework integrates the information from photoexcitation and thermal gradients to provide a general method to determine fundamental electronic properties of materials.

36 MATERIALS SCIENCE↗

Impact of Tiny Fermi Pockets with Extremely High Mobility on the Hall Anomaly in the Kagome Metal CsV 3 ⁢Sb 5

The kagome metal CsV 3 ⁢Sb 5 exhibits an unusual charge-density-wave (CDW) order, where the emergence of loop current order that breaks time-reversal symmetry (TRS) has been proposed. A key feature of this CDW phase is a nonmonotonic Hall effect at low fields, often attributed to TRS breaking. However, its origin remains unclear. Here, we conduct comprehensive magnetotransport measurements on CsV 3 ⁢Sb 5 and, through mobility spectrum analysis, identify the formation of tiny Fermi pockets with extremely high mobility below the CDW transition. Furthermore, electron irradiation experiments reveal that the nonmonotonic Hall effect is significantly suppressed in samples with reduced mobility, despite no substantial change in the electronic structure. In conclusion, these results indicate that the nonmonotonic Hall effect originates from these tiny Fermi pockets with high mobility carriers rather than anomalous Hall mechanisms, providing new insights into understanding the Hall anomaly in this kagome system.

36 MATERIALS SCIENCE↗

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

Problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars are reported. Problem areas include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis, terrain modeling and path selection; and chemical analysis of specimens. These tasks are summarized: vehicle model design, mathematical model of vehicle dynamics, experimental vehicle dynamics, obstacle negotiation, electrochemical controls, remote control, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer subsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, and chromatograph model evaluation and improvement.

Frederick, D. K.↗

The Robotic All-Terrain Lunar Exploration Rover (RATLER): Increased mobility through simplicity

A new concept mobility chassis for a robotic rover is described which is inherently simple with few moving parts or complex linkages. The RATLER design utilizes a four-wheel drive, skid steered propulsion system in conjunction with passive articulation of the dual body vehicle. This uniquely simple method of chassis articulation allows all four wheels to remain in contact with the ground even while climbing obstacles as large as 1.3 wheel diameters. A prototype mobility platform was built which is approximately 1 m(sup 2) with 0.5 m diameter wheels and all-wheel electric drive. The theoretical mobility limitations are discussed and compared with the results of field trials of the prototype platform. The theoretical model contrasted with measured performance is then used to predict the expected mobility of the RATLER design on the Lunar surface.

Pletta, J. Bryan↗

Wake Vortex Field Measurement Program at Memphis, Tennessee: Data Guide

Eliminating or reducing current restrictions in the air traffic control system due to wake vortex considerations would yield increased capacity, decreased delays, and cost savings. Current wake vortex separation standards are widely viewed as very conservative under most conditions. However, scientific uncertainty about wake vortex behavior under different atmospheric conditions remains a barrier to development of an adaptive vortex spacing system. The objective of the wake vortex field measurement efforts during December, 1994 and August, 1995 at Memphis, TN were to record wake vortex behavior for varying atmospheric conditions and types of aircraft. This effort is part of a larger effort by the NASA Langley Research Center to develop an Aircraft Vortex Spacing System (AVOSS) as an element of the Terminal Area Productivity (TAP) program. The TAP program is being performed in concert with the FAA Terminal Air Traffic Control Automation (TATCA) program and ATC Automation. Wake vortex behavior was observed using a mobile continuous-wave (CW) coherent laser Doppler radar (lidar) developed at Lincoln Laboratory. This lidar features a number of improvements over previous systems, including the first-ever demonstration of an automatic wake vortex detection and tracking algorithm.

Campbell, S. D.↗

Aerodynamic Characterization and Improved Testing Methods for the Space Launch System Liftoff and Transition Environment

Low-speed wind tunnel testing for the liftoff and transition environment of the Space Launch System (SLS) was recently completed in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel using 1.75%-scale models of three SLS vehicle configurations. During the liftoff testing, the primary objective was to evaluate the aerodynamic forces and moments on the SLS launch vehicles, as the vehicle, launch tower, and mobile launch platform were subjected to ground winds from all directions at varying heights for the vehicle off the launch pad. Additionally, aerodynamic forces and moments were acquired for all three SLS vehicles during the transition phase from liftoff to ascent that covered a wide range of angles of attack and angles of side slip. Details of the experimental setup including improved testing methods and a stiffer sting-balance system based on lessons learned from previous test entries are presented. Also, a new force measurement technique was applied during the test where two subminiature six-component load cells were installed in each Solid Rocket Booster (SRB) to acquire forces and moments for each SRB separately from the full vehicle forces and moments measured by the main strain gauge balance. Finally, sample results from the experiment are presented including improved overall data coverage, evaluation of the new SRB data, and smoke flow visualization photos.

Chan, David T.↗

High energy resolution five-crystal spectrometer for high quality fluorescence and absorption measurements on an x-ray absorption spectroscopy beamline

Fluorescence detection is classically achieved with a solid state detector (SSD) on x-ray absorption spectroscopy (XAS) beamlines. This kind of detection however presents some limitations related to the limited energy resolution and saturation. Crystal analyzer spectrometers (CAS) based on a Johann-type geometry have been developed to overcome these limitations. We have tested and installed such a system on the BM30B/CRG-FAME XAS beamline at the ESRF dedicated to the structural investigation of very dilute systems in environmental, material and biological sciences. The spectrometer has been designed to be a mobile device for easy integration in multi-purpose hard x-ray synchrotron beamlines or even with a laboratory x-ray source. The CAS allows to collect x-ray photons from a large solid angle with five spherically bent crystals. It will cover a large energy range allowing to probe fluorescence lines characteristic of all the elements from Ca (Z = 20) to U (Z = 92). It provides an energy resolution of 1-2 eV. XAS spectroscopy is the main application of this device even if other spectroscopic techniques (RIXS, XES, XRS, etc.) can be also achieved with it. The performances of the CAS are illustrated by two experiments that are difficult or impossible to perform with SSD and the complementarity of the CAS vs SSD detectors is discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

New particle formation in the sulfuric acid–dimethylamine–water system: reevaluation of CLOUD chamber measurements and comparison to an aerosol nucleation and growth model

Here, a recent CLOUD (Cosmics Leaving OUtdoor Droplets) chamber study showed that sulfuric acid and dimethylamine produce new aerosols very efficiently and yield particle formation rates that are compatible with boundary layer observations. These previously published new particle formation (NPF) rates are reanalyzed in the present study with an advanced method. The results show that the NPF rates at 1.7 nm are more than a factor of 10 faster than previously published due to earlier approximations in correcting particle measurements made at a larger detection threshold. The revised NPF rates agree almost perfectly with calculated rates from a kinetic aerosol model at different sizes (1.7 and 4.3 nm mobility diameter). In addition, modeled and measured size distributions show good agreement over a wide range of sizes (up toca. 30 nm). Furthermore, the aerosol model is modified such that evaporation rates for some clusters can be taken into account; these evaporation rates were previously published from a flow tube study. Using this model, the findings from the present study and the flow tube experiment can be brought into good agreement for the high base-to-acid ratios ( ~ 100)relevant for this study. This confirms that nucleation proceeds at rates that are compatible with collision-controlled (a.k.a.kinetically controlled) NPF for the conditions during the CLOUD7 experiment (278 K, 38 % relative humidity, sulfuric acid concentration between 1 × 10 6 and 3 × 10 7 cm -3 , and dimethylamine mixing ratio of ~ 40 pptv, i.e., 1 × 10 9 cm -3 ) .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simulation Based Studies of Low Latency Teleoperations for NASA Exploration Missions

Human exploration of Mars will involve both crewed and robotic systems. Many mission concepts involve the deployment and assembly of mission support assets prior to crew arrival on the surface. Some of these deployment and assembly activities will be performed autonomously while others will be performed using teleoperations. However, significant communications latencies between the Earth and Mars make teleoperations challenging. Alternatively, low latency teleoperations are possible from locations in Mars orbit like Mars' moons Phobos and Deimos. To explore these latency opportunities, NASA is conducting a series of studies to investigate the effects of latency on telerobotic deployment and assembly activities. These studies are being conducted in laboratory environments at NASA's Johnson Space Center (JSC), the Human Exploration Research Analog (HERA) at JSC and the NASA Extreme Environment Mission Operations (NEEMO) underwater habitat off the coast of Florida. The studies involve two human-in-the-loop interactive simulations developed by the NASA Exploration Systems Simulations (NExSyS) team at JSC. The first simulation investigates manipulation related activities while the second simulation investigates mobility related activities. The first simulation provides a simple real-time operator interface with displays and controls for a simulated 6 degree of freedom end effector. The initial version of the simulation uses a simple control mode to decouple the robotic kinematic constraints and a communications delay to model latency effects. This provides the basis for early testing with more detailed manipulation simulations planned for the future. Subjects are tested using five operating latencies that represent teleoperation conditions from local surface operations to orbital operations at Phobos, Deimos and ultimately high Martian orbit. Subject performance is measured and correlated with three distance-to-target zones of interest. Each zone represents a target distance ranging from beyond 10m in Zone 1, through 1 cm to contact in Zone 5 with a step size factor of 10. Collected data consists of both objective simulation data (time, distance, hand controller inputs, velocity) and subjective questionnaire data. The second simulation provides a simple real-time operator interface with displays and control of a simulated surface rover. The rover traverses a synthetic Mars-like terrain and must be maneuvered to avoid obstacles while progressing to its destination. Like the manipulator simulation, subjects are tested using five operating latencies that represent teleoperation conditions from local surface operations to orbital operations at Phobos, Deimos and ultimately high Martian orbit. The rover is also operated at three different traverse speeds to assess the correlation between latency and speed. Collected data consisted of both objective simulation data (time, distance, hand controller inputs, braking) and subjective questionnaire data. These studies are exploring relationships between task complexity, operating speeds, operator efficiencies, and communications latencies for low latency teleoperations in support of human planetary exploration. This paper presents early results from these studies along with the current observations and conclusions. These and planned future studies will help to inform NASA on the potential for low latency teleoperations to support human exploration of Mars and inform the design of robotic systems and exploration missions.

Gernhardt, Michael L.↗

A comprehensive diffusion mobility database comprising 23 elements for magnesium alloys

We report that reliable experimental diffusion coefficients of 10 key alloying elements in Mg obtained by the present authors together with experimental data in the literature enabled us to perform a systematic test of the reliability of diffusion coefficients obtained from DFT calculations. The computed activation energy values were found to be quite accurate (mostly within 0.2 eV) but the computed pre-factors were less reliable. Such insights allowed us to develop a practical and yet robust strategy to perform diffusion mobility assessments by adopting the computed activation energy while fitting only the pre-factor when available experimental data are limited to a narrow temperature range. The overall good agreement between the DFT data and experimental data also gave us the confidence to employ the computed data for those that were still missing or inaccessible from experimental measurements. A systematic assessment of both the measured and computed diffusion data in hcp Mg was performed using the above holistic approach to yield the most comprehensive open Mg mobility database to date, comprising 23 elements (Mg, Ag, Al, Be, Ca, Cd, Ce, Cu, Fe, Ga, Gd, In, La, Li, Mn, Nd, Ni, Pu, Sb, Sn, U, Y, Zn). This more reliable mobility database will contribute to future development of advanced Mg alloys. The holistic approach developed in this study will be very beneficial to the future establishment of reliable mobility databases for other alloy systems as well.

36 MATERIALS SCIENCE↗

In situ X-ray Diffraction Study of Ni–Yb Interlayer and Alloy Systems on Si„100

The phase formation in the ternary Ni/Yb/Si system was studied for Ni-Yb alloy and interlayer structures on Si(100) substrates using in situ x-ray diffraction measurements. Yb was treated as an alloying element in the Ni-Si system with Yb concentrations varying between 0 and 40 at. % of the Ni concentration. Independent of the initial structure of the sample, a Ni-Si or Ni-Yb compound was detected first which suggests that Ni is the dominant diffusing species during the solid state reactions. No pure Yb silicides were identified but a ternary phase (YbNi{sub 2}Si{sub 2}) formed in all samples after the Si atoms became mobile. Information about the distribution of the phases throughout the thin silicide film was obtained using ex situ Rutherford backscattering analysis. Independent of the Yb concentration, the NiSi phase formed at the substrate interface. As a result, the immobile Yb atoms shifted toward the sample surface and no detectable amount of Yb atoms was left at the Ni-silicide/Si interface after annealing.

36 MATERIALS SCIENCE↗

Supersonic and subsonic measurements of mesospheric ionization.

An Arcas rocket-parachute system was used at night to compare supersonic and subsonic ionization measurements below 75 km. A hemispherical nose-tip probe was used on ascent and a parachute-borne blunt probe on descent to measure polar conductivities, which were due entirely to positive and negative ions. The velocity of the supersonic probe was Mach 2.5 at 50 km and 1.75 at 70 km; the blunt probe was subsonic below 71 km. Between 65 and 75 km the ratio of negative to positive conductivities (and thus of mobilities) determined by the blunt probe was about 1.2, and it approached 1 below this altitude range. The ratio obtained by the nose-tip probe varied from 1.5 at 75 km to .6 at 65 km, thus indicating a rapid variation of the effects of the shock wave on the sampled ions. The absolute values of positive conductivity measured subsonically and supersonically were essentially identical from 60 to 75 km, indicating that the sampled ions were unchanged by the shock. However, below 60 km the shock apparently 'broke up' the positive ions, as indicated by higher measured conductivities.

Hale, L. C.↗

Site Selection for Field Testing of a Marine Hydrokinetic Turbine Platform to Serve as a Floating Unmanned Mobile Recharging Station for Aerial Drones

Abstract Expanding applications of unmanned aerial vehicles (UAVs) in coastal areas suggests a need for stations along or close to the coast where the UAV batteries can be easily recharged. A small-scale low flow marine current turbine in support of a floating autonomous recharge station for small UAVs has been designed and assembled at Florida Atlantic University and is being prepared for field testing. Surveys of identified test sites in the Intracoastal Waterways and at open ocean locations are being conducted to determine their suitability in meeting resource, system design and permitting requirements. A sensor platform has been developed for measuring local currents at the identified sites in support of resource characterization. Two out of the eight sites surveyed in the Intracoastal Waterways are found to meet the field-testing requirements for current resource, water depth, and sea bottom conditions. Planned field testing will include parametric characterization studies of the performance of the current turbine for a range of turbine blade configurations, current speeds, turbine wheel submergence levels, and test site location (channeled flow vs open ocean flow).

McKinney, Adriana Lynell↗