Search NASA⌕ Search

SEARCH · Search NASA

Results for “Orbiter Loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Task 3 Milestone Report, Kennedy Space Center (KSC) LOX Loading Facility Analyses

Transient thermodynamic analyses have been made for the Kennedy Space Center (KSC) LOX loading system proposed for the space shuttle. The primary objective of these analyses is to predict the sensitivity of system performance to operating procedures, flow rate, temperature, and quality at the orbiter (ORB)/ground service equipment (GSE) interface. A further objective is to establish required system chill-down times. These analyses also include the prediction of transient thermodynamic conditions for the facility vent line, shuttle main engine (SSME) feed line entrance, ORB/ET interface, and the ET entrance (tank bottom).

Glasgow, V. L.↗

Structural and mechanical design challenges of space shuttle solid rocket boosters separation and recovery subsystems

The design of the space shuttle solid rocket booster (SRB) subsystems for reuse posed some unique and challenging design considerations. The separation of the SRBs from the cluster (orbiter and external tank) at 150,000 ft when the orbiter engines are running at full thrust meant the two SRBs had to have positive separation forces pushing them away. At the same instant, the large attachments that had reacted launch loads of 7.5 million pounds thrust had to be servered. These design considerations dictated the design requirements for the pyrotechnics and separation rocket motors. The recovery and reuse of the two SRBs meant they had to be safely lowered to the ocean, remain afloat, and be owed back to shore. In general, both the pyrotechnic and recovery subsystems have met or exceeded design requirements. In twelve vehicles, there has only been one instance where the pyrotechnic system has failed to function properly.

Woodis, W. R.↗

Conceptual arcjet system design considerations for the SP-100 mission

Conceptual spacecraft design considerations for using 30-kW class arcjet engines as an active load for a 100-kWe SP-100 space nuclear reactor power system flight experiment are discussed. These design considerations involve configuration trades; interfaces with power, attitude and velocity control, thermal management, orbit insertion and reaction control propulsion systems; imposed environments concerned with electromagnetic noise, survivability, and ammonia exhaust plumes; and associated diagnostic instrumentation.

Zafran, Sidney↗

HL-20 structural design comparison - Conformal shell versus cylindrical crew compartment

Extensive studies have been performed at NASA Langley Research Center (LaRC) on personnel launch systems (PLS) concepts. The primary mission of a PLS is the transport of Space Station crew members from Earth to the Space Station and return. The NASA LaRC PLS studies have led to the design of a lifting body configuration named the HL-20. In this study, two different HL-20 structural configurations are evaluated. The two configurations are deemed the conformal shell and the cylindrical crew compartment. The configurations are based on two different concerns for maintenance and operations. One configuration allows for access to subsystems while on-orbit from the interior, while the other allows for easy access to the subsystems during ground maintenance and operations. For each concept, the total structural weight required to sustain the applied loads is quantified through a structural evaluation. Structural weight for both configurations is compared along with the particular attributes of each. Analyses of both configurations indicate no appreciable weight or load relief advantage of one concept over the other. Maintainability and operability, therefore become the primary discriminator, leading to a choice of a crew compartment configuration.

Bush, Lance B.↗

Microgravity Vibration Control and Civil Applications

Controlling vibration of structures is essential for both space structures as well as terrestrial structures. Due to the ambient acceleration levels anticipated for the International Space Station, active vibration isolation is required to provide a quiescent acceleration environment for many science experiments. An overview is given of systems developed and flight tested in orbit for microgravity vibration isolation. Technology developed for vibration control of flexible space structures may also be applied to control of terrestrial structures such as buildings and bridges subject to wind loading or earthquake excitation. Recent developments in modern robust control for flexible space structures are shown to provide good structural vibration control while maintaining robustness to model uncertainties. Results of a mixed H-2/H-infinity control design are provided for a benchmark problem in structural control for earthquake resistant buildings.

Whorton, Mark Stephen↗

The Software Design for the Wide-Field Infrared Explorer Attitude Control System

The Wide-Field Infrared Explorer (WIRE), currently scheduled for launch in September 1998, is the fifth of five spacecraft in the NASA/Goddard Small Explorer (SMEX) series. This paper presents the design of WIRE's Attitude Control System flight software (ACS FSW). WIRE is a momentum-biased, three-axis stabilized stellar pointer which provides high-accuracy pointing and autonomous acquisition for eight to ten stellar targets per orbit. WIRE's short mission life and limited cryogen supply motivate requirements for Sun and Earth avoidance constraints which are designed to prevent catastrophic instrument damage and to minimize the heat load on the cryostat. The FSW implements autonomous fault detection and handling (FDH) to enforce these instrument constraints and to perform several other checks which insure the safety of the spacecraft. The ACS FSW implements modules for sensor data processing, attitude determination, attitude control, guide star acquisition, actuator command generation, command/telemetry processing, and FDH. These software components are integrated with a hierarchical control mode managing module that dictates which software components are currently active. The lowest mode in the hierarchy is the 'safest' one, in the sense that it utilizes a minimal complement of sensors and actuators to keep the spacecraft in a stable configuration (power and pointing constraints are maintained). As higher modes in the hierarchy are achieved, the various software functions are activated by the mode manager, and an increasing level of attitude control accuracy is provided. If FDH detects a constraint violation or other anomaly, it triggers a safing transition to a lower control mode. The WIRE ACS FSW satisfies all target acquisition and pointing accuracy requirements, enforces all pointing constraints, provides the ground with a simple means for reconfiguring the system via table load, and meets all the demands of its real-time embedded environment (16 MHz Intel 80386 processor with 80387 coprocessor running under the VRTX operating system). The mode manager organizes and controls all the software modules used to accomplish these goals, and in particular, the FDH module is tightly coupled with the mode manager.

Anderson, Mark O.↗

Geoscience Laser Altimeter System (GLAS) Loop Heat Pipes: An Eventual First Year On-Orbit

Goddard Space Flight Center's Geoscience Laser Altimeter System (GLAS) is the sole scientific instrument on the Ice, Cloud and land Elevation Satellite (ICESat) that was launched on January 12, 2003 from Vandenberg AFB. A thermal control architecture based on propylene Loop Heat Pipe technology was developed to provide selectable/stable temperature control for the lasers and other electronics over the widely varying mission environment. Following a nominal LHP and instrument start-up, the mission was interrupted with the failure of the first laser after only 36 days of operation. During the 5-month failure investigation, the two GLAS LHPs and the electronics operated nominally, using heaters as a substitute for the laser heat load. Just prior to resuming the mission, following a seasonal spacecraft yaw maneuver, one of the LHPs deprimed and created a thermal runaway condition that resulted in an emergency shutdown of the GLAS instrument. This paper presents details of the LHP anomaly, the resulting investigation and recovery, along with on-orbit flight data during these critical events.

Grob, E.↗

Flow Separation Side Loads Excitation of Rocket Nozzle FEM

Modern rocket nozzles are designed to operate over a wide range of altitudes, and are also built with large aspect ratios to enable high efficiencies. Nozzles designed to operate over specific regions of a trajectory are being replaced in modern launch vehicles by those that are designed to operate from earth to orbit. This is happening in parallel with modern manufacturing and wall cooling techniques allowing for larger aspect ratio nozzles to be produced. Such nozzles, though operating over a large range of altitudes and ambient pressures, are typically designed for one specific altitude. Above that altitude the nozzle flow is 'underexpanded' and below that altitude, the nozzle flow is 'overexpanded'. In both conditions the nozzle produces less than the maximum possible thrust at that altitude. Usually the nozzle design altitude is well above sea level, leaving the nozzle flow in an overexpanded state for its start up as well as for its ground testing where, if it is a reusable nozzle such as the Space Shuttle Main Engine (SSME), the nozzle will operate for the majority of its life. Overexpansion in a rocket nozzle presents the critical, and sometimes design driving, problem of flow separation induced side loads. To increase their understanding of nozzle side loads, engineers at MSFC began an investigation in 2000 into the phenomenon through a task entitled "Characterization and Accurate Modeling of Rocket Engine Nozzle Side Loads", led by A. Brown. The stated objective of this study was to develop a methodology to accurately predict the character and magnitude of nozzle side loads. The study included further hot-fire testing of the MC-l engine, cold flow testing of subscale nozzles, CFD analyses of both hot-fire and cold flow nozzle testing, and finite element (fe.) analysis of the MC-1 engine and cold flow tested nozzles. A follow on task included an effort to formulate a simplified methodology for modeling a side load during a two nodal diameter fluid/structure interaction for a single moment in time.

Smalley, Kurt B.↗

Particle Loading Tests on HEPA Flat Sheet Media at Sub-Ambient Pressures Using a Lunar Dust Simulant

When humans return to the moon under the NASA Artemis program, their activities on the lunar surface will inevitably lead to the intrusion of some level of lunar dust into the lander cabin. Therein the crew would be exposed to the potential hazards of lunar dust and the possibility of subsequent transfer into orbiting segments after docking. The spacecraft’s cabin filtration system will need to be effective at removing the airborne lunar dust to properly purify the breathable cabin air and minimize the spreading of the dust throughout the vehicle and orbital segments through the mission duration. The fine nature of the lunar dust will require high efficiency filtration, such as HEPA. A series of tests were performed in a specially designed recirculating sealed flow loop, for testing filter media and filter elements at the NASA Glenn Research Center. The flow loop was used to assess the performance and capacity of flat sheet filter media at representative cabin pressures using JSC-1AF lunar he filter media was measured as a function of accumulated particle mdust simulant and at high rates of particle loading. The pressure drop across tass load at ambient pressure and at two sub-ambient pressures, 0.0703MPa and 0.0565MPa, and at a media velocity that was scaled relative to its pleated configuration. The challenge particle flows were generated by a custom designed particle generator that introduces dispersed particles of the lunar simulant at high concentrations. An optical particle counting instrument provided filter efficiency measurements within the sealed environment. The pressure drop was found to increase linearly with the amount of dust load on the media, for all test conditions, while the starting pressure drop was found to be lower at the lowest sub-ambient pressure case. High filter efficiency was maintained after high particle loads on the media

Sub-ambient↗

Design of a space shuttle structural dynamics model

A 1/8 scale structural dynamics model of a parallel burn space shuttle has been designed. Basic objectives were to represent the significant low frequency structural dynamic characteristics while keeping the fabrication costs low. The model was derived from the proposed Grumman Design 619 space shuttle. The design includes an orbiter, two solid rocket motors (SRM) and an external tank (ET). The ET consists of a monocoque LO2 tank an interbank skirt with three frames to accept SRM attachment members, an LH2 tank with 10 frames of which 3 provide for orbiter attachment members, and an aft skirt with on frame to provide for aft SRM attachment members. The frames designed for the SRM attachments are fitted with transverse struts to take symmetric loads.

Source record↗

Dynamic analysis and test results of the Viking Orbiter

The Viking Orbiter (VO) was launched in August 1975 on a new Titan/Centaur launch vehicle. Weight limitations of the VO and the use of a new launch vehicle made it necessary to conduct a load analysis which was verified by a test. The load analysis required a good mathematical dynamic model. Attention is given to aspects of mathematical formulation, subsystem characteristics, the body displacement functions, the propulsion subsystem, details regarding the dynamic model, the static test, and the sine vibration test.

Wada, B. K.↗

Stability analysis of a reinforced carbon carbon shell

This paper presents the development of a stability analysis for the nose cap of the NASA Space Shuttle Orbiter. Stability is evaluated by the differential stiffness analysis of the NASTRAN finite-element computer code, addressing those nonstandard characteristics in the nose cap such as nonuniform curvature, asymmetrical and nonuniform loads, support fixity, and various combinations of membrane and bending stresses. A full-sized nose cap, thinner than production, was statically tested and stability analyzed. The failing load level correlated to within 30%. The region and mode of buckling that occurred during test was accurately predicted by analysis. The criterion for predicting instability is based on the behavior of the nonlinear deflections. The deflections are nonlinear elastic in that the stresses are well within the elastic range of the material, but the geometry-load relationship produces nonlinear deflections. The load-deflection relationship is well defined by differential stiffness analysis up to the zero-slope portion of the curve, the point of neutral stability or where the shell 'snaps through' just prior to general instability.

Agan, W. E.↗

Use of arc-jet hypersonic blunted wedge flows for evaluating performance of Orbiter TPS

Arc-jet tests at NASA/JSC have been conducted recently to evaluate the performance of the Orbiter Thermal Protection System (TPS) on three critical areas of the side and top of the Orbiter fuselage: (1) cargo bay door, (2) crew access door, and (3) LRSI/FRSI joint regions. Test articles corresponding to these three areas on the Orbiter were mounted in an arc-jet test chamber in a blunted-wedge holder and exposed to hypersonic flow at various angles of attack. The effects of flow direction, heating load, and overtemperature were investigated. In addition, the reuse capability of the TPS materials was evaluated, along with the protection of the pressure seals within the test articles. Thermal match model predictions correlated well with primary structure thermocouple data. Heating rate and pressure predictions based on a nonequilibrium flow field computer program showed good agreement with arc-jet test data and existing hypersonic flow theories.

Rochelle, W. C.↗

Mechanisms to deploy the two-stage IUS from the shuttle cargo bay

The Inertial Upper Stage (IUS) is a two-stage or three-stage booster used to transport spacecraft from the space shuttle orbit to synchronous orbit or on an interplanetary trajectory. The mechanisms which were designed specifically to perform the two-stage IUS required functions while contained within the cargo bay of the space shuttle during the boost phase and while in a low Earth orbit are discussed. The requirements, configuration, and operation of the mechanisms are described, with particular emphasis on the tilt actuator and the mechanism for decoupling the actuators during boost to eliminate redundant load paths.

Haynie, H. T.↗

Shuttle orbiter flash evaporator operational flight test performance

The Flash evaporator System (FES is part of the Shuttle Orbiter Active Thermal Control Subsystem. The FES provides total heat rejection for the vehicle Freon Coolant Loops during ascent and entry and supplementary heat rejection during orbital mission phases. This paper reviews the performance of the FES during the first two Shuttle orbital missions (STS-1 and STS-2). A comparison of actual mission performance against design requirements is presented. Mission profiles (including Freon inlet temperature and feedwater pressure transients), control temperature, and heat load variations are evaluated. Anomalies that occurred during STS-2 are discussed along with the procedures conducted, both in-flight and post-flight, to isolate the causes. Finally, the causes of the anomalies and resulting corrective action taken for STS-3 and subsequent flights are presented.

Nason, J. R.↗

Systems integration for the Kennedy Space Center (KSC) Robotics Applications Development Laboratory (RADL)

A laboratory for developing robotics technology for hazardous and repetitive Shuttle and payload processing activities is discussed. An overview of the computer hardware and software responsible for integrating the laboratory systems is given. The center's anthropomorphic robot is placed on a track allowing it to be moved to different stations. Various aspects of the laboratory equipment are described, including industrial robot arm control, smart systems integration, the supervisory computer, programmable process controller, real-time tracking controller, image processing hardware, and control display graphics. Topics of research include: automated loading and unloading of hypergolics for space vehicles and payloads; the use of mobile robotics for security, fire fighting, and hazardous spill operations; nondestructive testing for SRB joint and seal verification; Shuttle Orbiter radiator damage inspection; and Orbiter contour measurements. The possibility of expanding the laboratory in the future is examined.

Davis, V. Leon↗

Superheavyweight missions SI versus DI: Ascent flight design options and recommendations

AFD has completed the trade study on Standard Insertion (SI) vs Direct Insertion (DI) for STS-50. RSOC Range Safety has developed acceptable DI targets from 130 n.mi. to 150 n.mi. and the corresponding performance assessment for these targets using STS-50 data has been completed. This mission has sufficient performance capability to perform this mission as a DI to 160 n.mi. A reduced OMS load corresponding to a DI mission is required for this option. The increase in altitude over the AFP baseline (SI to 145 n.mi.) is highly desirable for this mission. The orientation on orbit for the orbiter/USML-1 payload is such that orbital decay is maximized (maximum frontal cross-sectional area with vehicle normal to velocity vector). Increasing the operational altitude reduces the amount of vernier thruster firings necessary to maintain a constant gravity gradient. The results of this trade study can also be applied to other superheavyweight missions (EDO flights) and will allow for use of the DI technique for lower orbital altitudes, thereby eliminating the SI option for due east, low altitude missions. STSOC transmittal form no. 330-330-130, which documents the technical issues and assumptions used for this trade study effort in detail, should be referenced for further information. The main reason that a DI is desired for STS-50 and other superheavyweight flights (low altitude) is that ESMC range safety has expressed reservations about SI missions in general. The concern is that the current SI design underspeed exposes Africa and Madagascar to potential ET debris impact. In the past range safety has waived the requirement that these areas be protected in the event of an engine failure. With the advent of the pre-MECO OMS dump, the viability of DI and the high casualty expectations from the ACTA press to MECO hazard study, range safety has become more reluctant to approve SI flights. It is felt that to perform an SI mission there would have to be a large decrease in design underspeed to protect these landmasses, which would result in possible gaps between a late TAL and PTA. The assumed limit on a DI has been to altitudes greater than 160 n.mi. It was assumed that for altitudes less than 160 n.mi. the nominal ET impact envelope would overlap the Gilbert Islands.

Source record↗

Relation of the lunar power system to the SEI program and to landers

The people of Earth will need more than 20,000 billion watts (GWe) of electric power by 2050 for a high level of prosperity. Power needs in the 22nd Century could exceed 100,000 GWe. By 2100 the total quantity of thermal energy used could fully deplete the known inventory (10(exp 7) GWt-Y) of all non-renewable sources on Earth except for deuterium and hydrogen for use in proposed fusion reactors. The labor, capital, and mass of power plants required to produce 1 GWe-Y of energy from present-day power plants is summarized. Fossil and nuclear plants respectively consume 80 to 190 M$ and 12 to 48 M$ of fuel per GWe-Y. The Lunar Power System (LPS) uses solar power bases on the moon to beam electric power to Earth. The LPS in the figure supplies load-following power to rectennas on Earth. Additional solar power conversion units are located across the lunar limb from their respective Earthward transmitting stations. LPS can be augmented by mirrors in polar orbit about the moon. The construction of rectennas on Earth determines the base cost (0.001s$/kWe-H) of LPS power. A manned International Lunar Base (ILB) can accelerate the development of LPS by providing the initial transportation and habitation facilities and base operations. ILB can greatly reduce up front costs and risks by emplacing a moderate scale LPS (1-100 GWe). LPS can accelerate the development of the ILB by providing greater funding than is reasonable to expect for purely scientific research. An international ILB/LPS program can foster world trust and prosperity.

Criswell, David R.↗