SEARCH · Search NASA

Results for “Property optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

DOE OSTI2018

Non-isothermal creep aging behaviors of an Al-Zn-Mg-Cu alloy

Highlights: • A novel non-isothermal creep aging (NICA) process is proposed to improve sheet metal forming efficiency. • Appropriate heating-cooling rate is conducive to obtain desired creep deformation and material properties. • The time consumption in optimized NICA process is about half of that in conventional creep aging process. • In NICA, the precipitates formed in heating will be dissolved nearby the peak temperature and re-precipitated in cooling. - Abstract: To shorten production period and reduce manufacturing cost of high strength aluminum alloy integral panel components, a novel non-isothermal creep age forming (CAF) technology was developed. Taking an Al-Zn-Mg-Cu alloy as the case material, the non-isothermal creep aging (NICA) behavior and the conventional isothermal creep aging (ICA) behavior were comparatively investigated. The corresponding creep deformations, material performance variations and precipitate microstructure evolutions were studied by creep aging tests, mechanical property and corrosion resistance tests, and transmission electron microscope (TEM) and scanning electron microscope (SEM) characterizations. Unlike the ICA which contains short heating and cooling stages and long holding stage, the NICA only has heating and cooling stages, viz., the alloy is heated slowly and the cooling stage begins immediately when reaching the peak temperature. In the NICA process, the precipitates nucleate and grow up in the first half of heating stage, resulting in the reduction of creep rate and enhancement of mechanical strength. The coarsening of precipitates occurs in the second half of heating stage, elevating the creep rate and significantly improving the corrosion resistance. Nearby the peak temperature, the primary precipitates partially dissolve, and the creep rate, mechanical strength and corrosion resistance decrease. Distinctive from the ICA process, a secondary precipitation phenomenon takes place in the cooling stage of NICA, leading to the recovery of high mechanical strength. The higher heating-cooling rate (1 °C/min) is not beneficial to accumulating creep deformation in the shorter creep aging period, while the lower one (0.25 °C/min) causes the loss of mechanical strength due to the excessive dissolution of precipitates. The moderate heating-cooling rate (0.5 °C/min) can lead to larger creep deformation, better mechanical properties and more satisfactory corrosion resistances in the NICA treated alloy, reaching 87.0% of creep strain, 105.7% of yield strength and 97.9% of electric conductivity in the ICA treated alloy. It is worth noting that the time consumption of the optimal NICA process is only 52.9% of the ICA process.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Corrosion resistant hot melt adhesive to bind metals

Hot melt adhesives (HMAs) play an important role in many industries, and their demand is expected to grow. HMAs don't require any solvents, and their application results in the formation of strong bonds with the substrate upon cooling within seconds. These properties differentiate them from liquid glues and make them preferable for practical application. Currently, commercial HMAs are used in bonding lightweight materials such as paper, polymers, and cartons, and have limited usage in areas necessitating the bonding of heavier objects like metals. Here, in this study, we report a design and testing of versatile platform comprising an ion-coordinating polymer and ionic fillers for performance optimization and understanding of structure–property relationships, enabling the rational design of HMAs with improved adhesion to metal surfaces. All-atom Molecular dynamics (MD) simulations and various characterization methods are used to elucidate the adhesion mechanism in model composite system containing polyethylene oxide mixed with chemically diverse salt particles. The maximum adhesion strength is found in composites with Al(OH) 3 and FeCl 3 fillers. Interestingly, the presence of Al(OH) 3 also provides a multifunctional anticorrosion property as measured electrochemically using the Tafel method. The discovered path to formulations with improved adhesion to metal surfaces constitutes an important step toward advancing HMAs for use in the structural and semi-structural metal work domain.

Adhesive and cohesive forces↗

DOE OSTI2023

Polythiophene-based terpolymers with modulated aggregation behaviors for high-performance organic solar cells with 16.6% efficiency

Polythiophenes (PTs) are an attractive class of polymer donors (PDs) for organic solar cells (OSCs) owing to their relatively simple structures and scalable synthesis. Herein, a series of chlorinated thiazole-incorporated PT terpolymers are designed and high-performance OSCs with a power conversion efficiency (PCE) of 16.6% are demonstrated. By incorporating two different units, 3,3'-difluoro-2,2'-bithiophene (T2F2) and thieno[3,2-b]thiophene (TT), the aggregation properties of the terpolymers (PTz-FX; X = 0, 30, 50, 70, and 100, where X represents the mole percentage of T2F2 to total T2F2 +TT) are modulated. Among the PTz-FX series, PTz-F70 is found to be the optimal P D because its suitably tuned aggregation property leads to an optimized blend morphology with well-developed crystalline structures and donor–acceptor intermixed domains. The balanced morphology not only promotes charge generation/transport but also suppresses charge recombination in OSC devices. Thus, the PTz-F70-based OSCs achieve the highest PCE (16.6%), outperforming the OSCs based on PTz-FX with extremely strong (PTz-F100, PCE = 14.7%) or weak (PTz-F0, PCE = 12.0%) aggregation properties. The PCE of the PTz-F70-based OSCs is one of the highest performances among PT-based binary OSCs. Finally, this study highlights the importance of controlling the aggregation property of PTs for achieving high-performance PT-based OSCs.

14 SOLAR ENERGY↗

DOE OSTI2015

Magnetic Properties of Electroformed Ni and Ni-Fe for Micromagnetic MEMS Applications

This paper reports a new technique which is based on electroforming process for high permeability Ni and Ni-Fe alloy. The magnetic properties of Ni and Ni-Fe alloy are investigated as a function of plating current density via scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and vibrating sample magnetometer (VSM). Concentration-dependent kinetics is used to formulate the deposition rate and also the same is verified by using finite element analysis tool COMSOL Multiphysics. Several experiments are performed to derive the relation between electroplating parameters and magnetic properties. The process conditions are optimized to develop high permeability (∼16000) Ni-Fe alloy (85.71–14.29 %). The higher current density shows a monotonically increasing behavior of relative permeability (μ{sub r}). In addition, the B-H curves indicate that the saturation magnetization (B{sub sat}) increases and coercivity decreases with increasing plating current density. Our experimental data confirms that the higher current density increase the softness of Ni. The observed properties of Ni and Ni-Fe based on experimental results can be used to study the magnetic behavior of micromagnetic sensors and large force actuators.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

Adjoint DSMC for nonlinear Boltzmann equation constrained optimization

Applications for kinetic equations such as optimal design and inverse problems often involve finding unknown parameters through gradient-based optimization algorithms. Based on the adjoint-state method, we derive two different frameworks for approximating the gradient of an objective functional constrained by the nonlinear Boltzmann equation. While the forward problem can be solved by the DSMC method, it is difficult to efficiently solve the high-dimensional continuous adjoint equation obtained by the “optimize-then-discretize” approach. This challenge motivates us to propose an adjoint DSMC method following the “discretize-then-optimize” approach for Boltzmann-constrained optimization. We also analyze the properties of the two frameworks and their connections. Here, several numerical examples are presented to demonstrate their accuracy and efficiency.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2019

Characterization of light production and transport in tellurium dioxide crystals

Simultaneous measurement of phonon and light signatures is an effective way to reduce the backgrounds and increase the sensitivity of CUPID, a next-generation bolometric neutrinoless double-beta decay ($0\nu\beta\beta$) experiment. Light emission in tellurium dioxide (TeO$_2$) crystals, one of the candidate materials for CUPID, is dominated by faint Cherenkov radiation, and the high refractive index of TeO$_2$ complicates light collection. Positive identification of $0\nu\beta\beta$ events therefore requires high-sensitivity light detectors and careful optimization of light transport. A detailed microphysical understanding of the optical properties of TeO$_2$ crystals is essential for such optimization. We present a set of quantitative measurements of light production and transport in a cubic TeO$_2$ crystal, verified with a complete optical model and calibrated against a UVT acrylic standard. We measure the optical surface properties of the crystal, and set stringent limits on the amount of room-temperature scintillation in TeO$_2$ for $\beta$ and $\alpha$ particles of 5.3 and 8 photons / MeV, respectively, at 90% confidence. Finally, the techniques described here can be used to optimize and verify the particle identification capabilities of CUPID.

47 OTHER INSTRUMENTATION↗

DOE OSTI2016

Synthesis of Mg{sub 2}SiO{sub 4}:Dy{sup 3+} nanoparticles by hydrothermal method and investigation of their thermo and photo luminescence properties

Highlights: • Mg{sub 2}SiO{sub 4}:Dy{sup 3+} nanoparticles have been prepared by hydrothermal and combustion methods. • Thermo and photo luminescent behavior of Mg{sub 2}SiO{sub 4}:Dy{sup 3+} was studied. • The effect of synthesis method on TL properties of Mg{sub 2}SiO{sub 4}:Dy{sup 3+} was investigated. • The optimal dopant concentration for thermo-luminescent property was obtained. - Abstract: In this study, photo and thermo-luminescent properties of Nano crystalline Mg{sub 2}SiO{sub 4}:Dy{sup 3+} prepared by a hydrothermal method were studied and compared to those of nanoparticles prepared by combustion method. The synthesized sample was characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy and photoluminescence spectroscopy. The effect of Dy concentration on photo and thermoluminescent intensities was studied. The X-ray diffraction (XRD) patterns of the samples revealed that forsterite was formed as a major phase for all the samples. The crystallite size was found to be in the range of 20–50 nm. The thermo luminescent glow curve indicated that the hydrothermal sample was more efficient than the combustion sample. Two prominent TL bands located at 200 nm and 320 nm were recorded. The prepared nanoparticles exhibited a roughly linear dose response to absorbed dose of 1000 Gy received from 60Co gamma source, suggesting that nanomaterial could be a good candidate for high dose dosimetry.

36 MATERIALS SCIENCE↗

DOE OSTI2019

A Review on Binder Jet Additive Manufacturing of 316L Stainless Steel

Binder jet additive manufacturing enables the production of complex components for numerous applications. Binder jetting is the only powder bed additive manufacturing process that is not fusion-based, thus manufactured parts have no residual stresses as opposed to laser-based additive manufacturing processes. Binder jet technology can be adopted for the production of various small and large metallic parts for specific applications, including in the biomedical and energy sectors, at a lower cost and shorter lead time. One of the most well-known types of stainless steels for various industries is 316L, which has been extensively manufactured using binder jet technology. Binder jet manufactured 316L parts have obtained near full density and, in some cases, similar mechanical properties compared to conventionally manufactured parts. This article introduces methods, principles, and applications of binder jetting of SS 316L. Details of binder jetting processes, including powder characteristics (shape and size), binder properties (binder chemistry and droplet formation mechanism), printing process parameters (such as layer thickness, binder saturation, drying time), and post-processing sintering mechanism and densification processes, are carefully reviewed. Furthermore, critical factors in the selection of feedstock, printing parameters, sintering temperature, time, atmosphere, and heating rate of 316L binder jet manufactured parts are highlighted and summarized. Finally, the above-mentioned processing parameters are correlated with final density and mechanical properties of 316L components to establish a guideline on feedstock selection and process parameters optimization to achieve desired density, structure and properties for various applications.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Size- and Phase-Controlled Nanometer-Thick ß-Ga2O3 Films with Green Photoluminescence for Optoelectronic Applications

Realization and optimization of the tunable/enhanced optical properties is critical to further advance the field of optoelectronics, photonics, and nano-electronics. In this context, here, we demonstrate green-emission characteristics with a ~30 fold enhancement in selectively engineered nanocrystalline Ga2O3 with a control over size, phase and interface nanostructure. Pulsed-laser-deposited ß-phase Ga2O3 films with an average crystallite size of ~9 nm along with a highly dense, close-compact nano-columnar structure with lowest possible defect density facilitates the thirty-fold enhancement in the photoluminescence (PL) intensity in green-region. Enhanced PL-emission in the optimized, engineered nano-architecture sheds light in designing Ga2O3-materials for promising future optoelectronic/photocatalytic applications.

Ga2O3, Nanocrystalline Films, Pulsed-Laser Deposit↗

DOE OSTI2021

A Laboratory Assessment and Optimization of Nanoparticle-Stabilized CO2 Foams for Hydraulic Fracturing Applications

In this research, we have conducted a comprehensive assessment and optimization of aqueous CO2 foams for fracturing applications. The performance of CO2 foams is evaluated using three major matrices: foam stability, foam apparent viscosity, and leakoff. The response of these performance matrices to different internal factors and external conditions is evaluated. These factors and conditions include foam quality, nanoparticle concentration, salinity, shear rate, surfactant type and concentration, polymer concentration, and temperature. Before foam generation, the colloidal stability of the nanosilica dispersion is evaluated at different types of electrolytes and under high temperatures. With a good salinity resistance and thermal stability, the nanosilica is then used for the entire set of foam generation experiments. The foam configuration with optimized parameters is used for the leakoff test, which serves as a supplementary section to further demonstrate the advantages of the proposed foam system. Then the final commercialization section provides a general view of what should be considered to commercialize the research results. In general, it is found that the aqueous CO2 foam system has demonstrated a good potential to be used as a fracturing fluid. The design of the foam system needs to consider formations properties and formation fluid properties etc. to realize the optimal performance of the system on a laboratory scale.

02 PETROLEUM↗

DOE OSTI2025

Structural evolution and magnetic hardness of (Sm,Zr)(Fe,Co,Ti) 12 alloy particles via reduction-diffusion

The quest for achieving high coercivity in Sm(Fe,Co,Ti) 12 alloys, despite their inherent strong magnetocrystalline anisotropy, has posed significant challenges. Recently, (Sm,Zr)(Fe,Co,Ti) 12 monocrystalline particles have exhibited coercivity μ 0 H c > 1.2 T, showcasing promising prospects and significant potential for both manufacturing and research endeavors. This study delves into the structural evolution of (Sm,Zr)(Fe,Co,Ti) 12 (1:12) alloy particles made via the calciothermic reduction-diffusion synthesis process as influenced by the molar ratios of Ca atoms to O 2- ions (Ca/O), annealing time and annealing temperature. Critical insight that informs conditions to optimize the magnetic response is gained via systematic experimentation and advanced electron microscopy. Complex structural features, including core-shell morphologies and intricate multiphase compositions within individual particles, are unveiled. An optimal Ca/O ratio of 1.30 produces particles with a coercivity up to μ 0 H c = 1.63 T, while higher Ca/O ratios induce the formation of a Sm-rich TbCu 7 -type (1: 7 ) phase, which only partially transforms into the desired 1:12 phase during annealing. Persistent remnants of the 1:7 phase locally impact atomic structure, particle morphology, and coercivity. Furthermore, these findings underscore the complex interplay between synthesis parameters, resulting structures, and magnetic properties, informing the design and optimization of high-performance permanent magnets comprised of the (1:12) compound.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Benchtop Autonomous Electrochemical Characterization System for Combinatorial Thin-Film Solid Oxide Electrodes

The design of materials for electrochemical energy conversion is complicated by a vast search space of candidate materials and multifaceted property requirements: multicarrier conductivity, stability, and catalytic activity are all necessary but rarely intersect. Although self-driving laboratories are rapidly rising to address such material optimization problems, the required infrastructure for integrated, large-scale robotic facilities can be cost-prohibitive. Here we develop and evaluate a closed-loop measurement system for efficient screening of proton-conducting oxide electrodes for ceramic fuel cells and electrolyzers, building on top of an existing benchtop instrument and integrating techniques for rapid impedance measurement and automated analysis. This system exemplifies a “minimum viable” self-driving implementation that can deliver substantial benefits with relatively simple infrastructure. Combinatorial thin-film microelectrode libraries are characterized with a recently developed joint time-domain and frequency-domain impedance measurement technique, which provides an order-of-magnitude acceleration relative to conventional impedance spectroscopy. The distribution of relaxation times is extracted from impedance data and analyzed without human intervention. These results feed an active learning and Bayesian optimization process that learns to predict electrochemical impedance as a function of material composition, measurement temperature, oxygen partial pressure, and electrical bias, which further reduces the screening time by tenfold with optimized experimental sequences. We apply this system to Ba⁡(Co,Fe,Zr,Y)⁢O 3−𝛿 combinatorial libraries and evaluate its effectiveness for learning material property trends and optimizing expensive-to-evaluate properties such as activation energy. This offers insights into key methodological aspects of practical autonomous experimentation, including surrogate model validation, cost-aware acquisition functions, and high-throughput data interpretation. Our results demonstrate the efficacy of the system for rapidly gathering information, but also highlight real-world experimental challenges of thin-film degradation and numerical instability in surrogate models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2014

Identification and design of novel polymer-based mechanical transducers: A nano-structural model for thin film indentation

Mechanical characterization is important for understanding small-scale systems and developing devices, particularly at the interface of biology, medicine, and nanotechnology. Yet, monitoring sub-surface forces is challenging with current technologies like atomic force microscopes (AFMs) or optical tweezers due to their probe sizes and sophisticated feedback mechanisms. An alternative transducer design relying on the indentation mechanics of a compressible thin polymer would be an ideal system for more compact and versatile probes, facilitating measurements in situ or in vivo. However, application-specific tuning of a polymer's mechanical properties can be burdensome via experimental optimization. Therefore, efficient transducer design requires a fundamental understanding of how synthetic parameters such as the molecular weight and grafting density influence the bulk material properties that determine the force response. In this work, we apply molecular-level polymer scaling laws to a first order elastic foundation model, relating the conformational state of individual polymer chains to the macroscopic compression of thin film systems. A parameter sweep analysis was conducted to observe predicted model trends under various system conditions and to understand how nano-structural elements influence the material stiffness. We validate the model by comparing predicted force profiles to experimental AFM curves for a real polymer system and show that it has reasonable predictive power for initial estimates of the force response, displaying excellent agreement with experimental force curves. We also present an analysis of the force sensitivity of an example transducer system to demonstrate identification of synthetic protocols based on desired mechanical properties. These results highlight the usefulness of this simple model as an aid for the design of a new class of compact and tunable nanomechanical force transducers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2022

Characterization of the Fusion Zone in Laser Beam Welds on SS304L

Designing a welded joint requires consideration of the welding process, component/assembly structure and weld geometry, material composition, properties, and desired joint performance. The designer must also specify a set of acceptance criteria used to evaluate the welds. This study was conducted to support the design team responsible for specifying the spot weld profile by investigating the relationship between weld process parameters and the weld geometry and properties to further inform design optimization. The subjects of this study are two thin stainless steel 304L (SS304L) components joined by Laser Beam Welding (LBW). The components are the Housing, which contains flexible circuitry, and the Cover that protects the circuitry during handling, installation, and under service loads. Figure 1 illustrates coupon versions of the Cover and Housing used to simulate the interface between these components for weld testing. These coupon representations of assembly components were designed to match the material and relevant geometry related to the welded joint while other features not relevant to the welded joint are excluded.The objective of this study was to characterize the sensitivity of the weld geometry and mechanical properties to the input weld parameters to inform further Finite Element Analysis (FEA) efforts in balancing joint strength against assembly deformation caused by the welding process. Characterization was accomplished by varying laser welding parameters around the current design values and measuring weld geometry on the cross-sections. Nanoindentation with a spherical and flat-ended tip was used on polished section cuts of the weld to obtain direct estimates of the stress-strain response of the Fusion Zone (FZ) for comparison to the Base Metal (BM).

42 ENGINEERING↗

DOE OSTI2025

Correlating processing variables to material properties in recycled polypropylene: A data‐driven approach

Abstract Polypropylene (PP) is one of the most widely used plastics, yet its recycling remains limited, with less than 1% of solid waste PP being reprocessed. Mechanical recycling through extrusion is the most practical method, but inconsistent reprocessing conditions introduce variability in material properties. While temperature, screw speed, and residence time influence the thermomechanical stress applied during reprocessing, there are no standardized guidelines for optimizing these parameters. This study examines how these factors shape the properties of recycled PP, using conditions designed to mimic post‐industrial recycled (PIR) scrap. Residence time was measured using colorimetric tracking and correlated with molecular weight, viscosity, and mechanical properties over multiple extrusion cycles. Data‐driven modeling, including response surface methodology, support vector machines, and artificial neural networks, identified processing temperature as the dominant factor in material degradation, followed by residence time. Mechanical properties remained stable, while viscosity decreased predictably with increasing residence time. By linking reprocessing conditions to property evolution, this study provides a method to optimize processing parameters and reduce variability in recycled PP. These findings help manufacturers improve process control, making recycled PP more predictable for reuse in manufacturing. Highlights Study of PIR‐quality PP without additives or compatibilizers. Residence time analysis shows processing temperature drives PP property changes. Mark‐Houwink enables quick molecular weight checks for quality control. Models predict mechanical and rheological shifts in reprocessing. Optimized processing parameters minimize property degradation in recycling.

Estela‐García, John E. [Polymer Engineering Center↗

DOE OSTI2024

Evaluation of a New Approach for Entrainment and Detrainment Rate Estimation

Entrainment and detrainment rates (ε and δ) constitute the most critical free parameters in mass flux schemes commonly employed for cumulus parameterizations. Recently, Zhu et al. (2021) introduced a new approach that utilizes aircraft observations to simultaneously estimate ε and δ for cumulus clouds, overcoming the limitation of other observation-based approaches that solely yield ε without offering insights into δ. This study aims to comprehensively evaluate the reliability of this new approach. First, evaluation using an Explicit Mixing Parcel Model demonstrates the capability of the new approach to back-calculate predetermined ε and δ based on the physical properties before and after the entrainment mixing. Second, evaluation using large-eddy simulations illustrates that the new approach yields consistent ε and δ profiles compared to the traditional approach. Sensitivity tests indicate a weak sensitivity of the estimated δ with the new approach to the entrained air source. A decrease in the proportion of cloudy air in the assumed detrained air leads to a reduction in the estimated δ, while ε remains unaffected. Finally, the most appropriate assumptions for entrained and detrained air are discussed. Estimating ε for cumulus parameterizations involves acquiring ambient air more than 500 m away from the cloud edge as entrained air. Due to implicit mean field approximations in the traditional approach, determining the optimal assumption for detrained air properties proves challenging. Finally, this study confirms the reliability of the new approach in estimating ε and δ, providing confidence in its application to extensive observational data and advancement in parameterization.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2017

Laser modification of frictional surfaces

Improvement in the physicomechanical properties and frictional characteristics of cylinder and piston surfaces in airplane internal-combustion engines is considered. A method of developing recommendations regarding the optimization of laser treatment is proposed on the basis of experiments and a model of surface wear.

42 ENGINEERING↗

DOE OSTI2015

Simulative design and process optimization of the two-stage stretch-blow molding process

The total production costs of PET bottles are significantly affected by the costs of raw material. Approximately 70 % of the total costs are spent for the raw material. Therefore, stretch-blow molding industry intends to reduce the total production costs by an optimized material efficiency. However, there is often a trade-off between an optimized material efficiency and required product properties. Due to a multitude of complex boundary conditions, the design process of new stretch-blow molded products is still a challenging task and is often based on empirical knowledge. Application of current CAE-tools supports the design process by reducing development time and costs. This paper describes an approach to determine optimized preform geometry and corresponding process parameters iteratively. The wall thickness distribution and the local stretch ratios of the blown bottle are calculated in a three-dimensional process simulation. Thereby, the wall thickness distribution is correlated with an objective function and preform geometry as well as process parameters are varied by an optimization algorithm. Taking into account the correlation between material usage, process history and resulting product properties, integrative coupled simulation steps, e.g. structural analyses or barrier simulations, are performed. The approach is applied on a 0.5 liter PET bottle of Krones AG, Neutraubling, Germany. The investigations point out that the design process can be supported by applying this simulative optimization approach. In an optimization study the total bottle weight is reduced from 18.5 g to 15.5 g. The validation of the computed results is in progress.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗