Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tunnel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Tests were performed in a transient heat transfer tunnel in which the model under test was preheated prior to allowing room temperature air to be suddenly drawn over the model. The resulting movement of isothermal contours on the model is revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record is obtained of a temperature and time data pair for all points on the model during a single test. Experiments on a duct model are reported in which the model was preheated using a hot air stream. A manner in which initial model temperature nonuniformities could be taken into account was investigated. The duct model was also tested with a steady-state measurement technique and results were compared with the transient measurements, but recognizing that differences existed between the upstream thermal boundary conditions. The steady-state and transient measurements were shown to be consistent with predicted values. The main advantage of this transient heat transfer technique using liquid crystals is that since the test model need not be actively heated, high-resolution measurements on surfaces with complex shapes may be obtained.

Jones, Terry V.↗

An evaluation of factors affecting the flow quality in wind tunnels

Tests were conducted in a number of NASA wind tunnels to measure disturbance levels and spectra in their respective settling chambers, test sections, and diffusers to determine the sources of these disturbances. Results indicate that properly designed and located second minimum in transonic tunnels prevent fluctuation originating at struts and in diffusers from propagating upstream into the test section. The installation in or upstream of the settling chamber of carefully selected screens, honeycomb, and acoustic baffles could further reduce test section turbulence levels and scales without significant pressure losses. The performance of these modifications is strongly influenced by tunnel geometry and their influence on the mean flow around the circuit.

Owen, F. K.↗

Supersonic aerodynamic characteristics of a Mach 3 high-speed civil transport configuration

The NASA-Langley AST31 high-speed civil transport (HSCT) configuration, a blended wing/fuselage concept scaled for 250-passenger carriage over 6500 nmi, has been subjected to both CFD and wind tunnel tests; the wind tunnel tests were conducted in the Mach 1.6-3.6 range. The inability of the linear theory method to accurately predict stability levels as well as nonlinear pitching moment characteristics demonstrates the need to undertake high-order analyses as early in the design process as possible. An HSCT laminar flow capability experimental study was conducted in order to simulate 50-percent laminar flow conditions, and thereby ascertain the difference in drag relative to fully turbulent conditions.

Covell, Peter F.↗

Comparison of Wind-Tunnel and Flight Unsteady Pressure Stochastic Characteristics for the Space Launch System Artemis I Flight

Over the course of more than ten years, numerous wind-tunnel tests have been conducted to acquire data for characterizing the unsteady pressure environments expected to act on the Space Launch System Block 1 crew launch vehicle during ascent. These wind-tunnel tests of highly-instrumented rigid models are the current standard for the estimation of unsteady environments. Following the successful launch of the Artemis I mission, the extensive flight data acquired can be analyzed to evaluate the accuracy of unsteady pressure environments predicted in subscale wind-tunnel testing in comparison to the flight test data. In this paper, analyses focusing on data from several Space Launch System wind-tunnel tests and the Artemis I flight test are presented, including assessments of test-to-test, tunnel-to-tunnel, and tunnel-to-flight stochastic characteristics and preflight modeling validity based on wind-tunnel testing. In general, the fluctuating pressure environments measured during the several preflight subscale wind-tunnel tests compare favorably and provide relatively accurate estimates of the environments measured during flight. Discrepancies in fluctuating magnitudes, spatial extent of regions of unsteadiness, and narrowband frequency peaks are noted in the multibody region aft of the solid rocket booster forward attachment to the core stage.

wind-tunnel↗

Comparison of Wind-Tunnel and Flight Unsteady Pressure Stochastic Characteristics for the Space Launch System Artemis I Flight

Over the course of more than ten years, numerous wind-tunnel tests have been conducted to acquire data for characterizing the unsteady pressure environments expected to act on the Space Launch System Block 1 crew launch vehicle during ascent. These wind-tunnel tests of highly-instrumented rigid models are the current standard for the estimation of unsteady environments. Following the successful launch of the Artemis I mission, the extensive flight data acquired can be analyzed to evaluate the accuracy of unsteady pressure environments predicted in subscale wind-tunnel testing in comparison to the flight test data. In this paper, analyses focusing on data from several Space Launch System wind-tunnel tests and the Artemis I flight test are presented, including assessments of test-to-test, tunnel-to-tunnel, and tunnel-to-flight stochastic characteristics and preflight modeling validity based on wind-tunnel testing. In general, the fluctuating pressure environments measured during the several preflight subscale wind-tunnel tests compare favorably and provide relatively accurate estimates of the environments measured during flight. Discrepancies in fluctuating magnitudes, spatial extent of regions of unsteadiness, and narrowband frequency peaks are noted in the multibody region aft of the solid rocket booster forward attachment to the core stage.

wind-tunnel↗

Repeatability of ice shapes in the NASA Lewis icing research tunnel

Tests were conducted in the Icing Research Tunnel (IRT) at the NASA Lewis Research Center to document the current capability of the IRT, focused mainly on the repeatability of the ice shape over a range of icing conditions. Measurements of drag increase due to the ice accretion were also made to document the repeatability of drag. The repeatability of the ice shape was very good at low temperatures, but only fair at near freezing temperatures. In general, drag data shows good repeatability.

SHAPE REPEATABILITY↗

Porous wind tunnel corrections for counterrotation propeller testing

Wind tunnel interference corrections have direct impact on measured propeller efficiency. A systematic series of wind tunnel tests was done in the porous-wall NASA Lewis 8- by 6-Foot Wind Tunnel to determine the wind tunnel interference corrections to the NASA Lewis counterrotation propeller test data. The test results were compared with calculations from a potential flow code to determine the interference corrections. At a Mach number of 0.8, the interference corrections resulted in a -0.008 Mach number correction which reduced the counterrotation propeller net efficiency data by 0.46 percent at the reduced Mach number. Additional wind tunnel tests were done to measure the effect of propeller thrust on wind tunnel wall interference. No wall interference corrections due to propeller thrust were found necessary for the high speed counterrotation propeller data obtained in the porous wall NASA Lewis 8- by 6-Foot Wind Tunnel.

Stefko, George L.↗

Porous wind tunnel corrections for counterrotation propeller testing

Wind tunnel interference corrections have direct impact on measured propeller efficiency. A systematic series of wind tunnel tests was done in the porous-wall NASA Lewis 8- by 6-Foot Wind Tunnel to determine the wind tunnel interference corrections to the NASA Lewis counterrotation propeller test data. The test results were compared with calculations from a potential flow code to determine the interference corrections. At a Mach number of 0.8, the interference corrections resulted in a -0.008 Mach number correction which reduced the counterrotation propeller net efficiency data by 0.46 percent at the reduced Mach number. Additional wind tunnel tests were done to measure the effect of propeller thrust on wind tunnel wall interference. No wall interference corrections due to propeller thrust were found necessary for the high speed counterrotation propeller data obtained in the porous wall NASA Lewis 8- by 6-Foot Wind Tunnel.

Stefko, George L.↗

Acoustic Modifications of the Ames 40x80 Foot Wind Tunnel and Test Techniques for High-Speed Research Model Testing

The NFAC 40- by 80- Foot Wind Tunnel at Ames is being refurbished with a new, deep acoustic lining in the test section which will make the facility nearly anechoic over a large frequency range. The modification history, key elements, and schedule will be discussed. Design features and expected performance gains will be described. Background noise reductions will be summarized. Improvements in aeroacoustic research techniques have been developed and used recently at NFAC on several wind tunnel tests of High Speed Research models. Research on quiet inflow microphones and struts will be described. The Acoustic Survey Apparatus in the 40x80 will be illustrated. A special intensity probe was tested for source localization. Multi-channel, high speed digital data acquisition is now used for acoustics. And most important, phased microphone arrays have been developed and tested which have proven to be very powerful for source identification and increased signal-to-noise ratio. Use of these tools for the HEAT model will be illustrated. In addition, an acoustically absorbent symmetry plane was built to satisfy the HEAT semispan aerodynamic and acoustic requirements. Acoustic performance of that symmetry plane will be shown.

Soderman, Paul T.↗

An evaluation and assessment of flow quality in selected NASA wind tunnels

Tests have been conducted in a number of NASA wind tunnels to measure disturbance levels and spectra in their respective settling chambers, test sections, and diffusers to determine the sources of their disturbances. The present data supplements previous results in other NASA tunnels and adds to the ongoing acquisition of a disturbance level data base. The present results also serve to explain flow related sources which cause relatively large disturbance amplitudes at discrete frequencies. The installation of honeycomb, screens, and acoustic baffles in or upstream of the settling chamber can significantly reduce the disturbance levels.

Harvey, W. D.↗

Investigation of a Spoiler-Type Lateral Control System on a Wing with Full-Span Flaps in the Langley 19-Foot Pressure Tunnel

Tests of a partial-span model of a large bomber-type air1ane were conducted to determine the. aerodynamic characteristics of the wing equipped with full-span flaps and a retractable spoiler end aileron lateral control system. The arrangement consisted of (1) a double slotted flap extending over aproximate1y 86 percent of the wing semispan, (2) a 20-percent constant-percentage-chord aileron extending from the outboard end of the flap to the wing tip, and (3) a retractable spoiler, located at the 65-percent wing-chord station and extending from approximately 63 percent of the wing semispan to the wing tip. In addition, tests were made of a wing vent (of 1 and 2 percent of the wing chord located directly behind the spoiler), perforations in the spoiler, a blot or cut-out along the lower edge of the spoiler and spoilers of various spans. With full-span flaps deflected and with the 2-percent vent open or closed the initial stalling of the wing occurred at the tips, but with the vents closed there probably would be no appreciable loss in lateral control until maximum lift was reached. The l-percent vent increased the rolling effectiveness of the spoiler at small spoi1er deflections, particularly at high angles of attack with flaps deflected. With flaps deflected the 2-percent vent caused a large reduction in both the wing lift and rolling effectiveness of the spoiler at large angles of attack. However, at small angle of attack the 2-percent vent increased the rolling effectiveness of the spoiler at small spoiler deflections. The simultaneous operation of the spoiler and vent (in contrast to a vent fixed in the wing) would result in a large increase in the effectiveness of the spoiler and would avoid any loss in wing lift as in a fixed vent arrangement. The tests of the spoiler modifications revealed that (1) the spoiler perforations reduced the rolling-moment and yawing-moment coefficients but caused the spoiler hinge-moment coefficients to become more positive; (2) the spoiler slot had no notable effect on the rolling-moment and yawing-moment characteristics but produced a positive increase in the spoiler hinge-moment coefficients at large spoiler deflections; (3) the effects produced by the individual modifications were additive when the various modifications were combined. In general, progressively decreasing the spoiler span by removing the segments from the inboard end of the spoiler caused a decrease in rolling effectiveness approximately proportional to the span of the segment.

WING FLAPS, SLOTTED & AILERONS↗

Aerodynamic Measurements on a Large Splitter Plate for the NASA Langley Transonic Dynamics Tunnel

Tests conducted in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT) assess the aerodynamic characteristics of a splitter plate used to test some semispan models in this facility. Aerodynamic data are analyzed to determine the effect of the splitter plate on the operating characteristics of the TDT, as well as to define the range of conditions over which the plate can be reasonably used to obtain aerodynamic data. Static pressures measurements on the splitter plate surface and the equipment fairing between the wind tunnel wall and the splitter plate are evaluated to determine the flow quality around the apparatus over a range of operating conditions. Boundary layer rake data acquired near the plate surface define the viscous characteristics of the flow over the plate. Data were acquired over a range of subsonic, transonic and supersonic conditions at dynamic pressures typical for models tested on this apparatus. Data from this investigation should be used as a guide for the design of TDT models and tests using the splitter plate, as well as to guide future splitter plate design for this facility.

Schuster, David M.↗

A study of dynamic measurements made in the settling chamber of the Langley 0.3-meter transonic cryogenic tunnel

Tests have been conducted in a cryogenic wind tunnel settling chamber using a fast response instrumentation to measure the possible existence of temperature fronts due to a sudden or step change in the rate of liquid nitrogen injection into the circuit. No indications of such fronts were obtained using three different techniques to change the rate of nitrogen injection. The normalized pressure and velocity fluctuations at two total temperatures and over a large range of Mach numbers and Reynolds numbers were about 2 x 10 to the -7th to 2 x 10 to the -6th and about 1.8 to 3 percent, respectively. There was no evidence of liquid nitrogen droplets in the flow down to a total temperature of 140 K. The pressure fluctuation power spectra from a pressure transducer correlated with the fan blade passage through the eighth harmonic of the fundamental frequency.

Johnson, C. B.↗

Investigation of air flow in open-throat wind tunnels

Tests were conducted on the 6-inch wind tunnel of the National Advisory Committee for Aeronautics to form a part of a research on open-throat wind tunnels. The primary object of this part of the research was to study a type of air pulsation which has been encountered in open-throat tunnels, and to find the most satisfactory means of eliminating such pulsations. In order to do this it was necessary to study the effects of different variable on all of the important characteristics of the tunnel. This paper gives not only the results of the study of air pulsations and methods of eliminating them, but also the effects of changing the exit-cone diameter and flare and the effects of air leakage from the return passage. It was found that the air pulsations in the 6-inch wind tunnel could be practically eliminated by using a moderately large flare on the exit cone in conjunction with leakage introduced by cutting holes in the exit cone somewhat aft of its minimum diameter.

Jacobs, Eastman N↗

Actuated forebody strake controls for the F-18 high alpha research vehicle

A series of ground-based studies have been conducted to develop actuated forebody strake controls for flight test evaluations using the NASA F-18 High-Alpha Research Vehicle. The actuated forebody strake concept has been designed to provide increased levels of yaw control at high angles of attack where conventional rudders become ineffective. Results are presented from tests conducted with the flight-test strake design, including static and dynamic wind-tunnel tests, transonic wind-tunnel tests, full-scale wind-tunnel tests, pressure surveys, and flow visualization tests. Results from these studies show that a pair of conformal actuated forebody strakes applied to the F-18 HARV can provide a powerful and precise yaw control device at high angles of attack. The preparations for flight testing are described, including the fabrication of flight hardware and the development of aircraft flight control laws. The primary objectives of the flight tests are to provide flight validation of the groundbased studies and to evaluate the use of this type of control to enhance fighter aircraft maneuverability.

Murri, Daniel G.↗

Calibration of the Langley 16-foot transonic tunnel with test section air removal

The Langley 16-foot transonic tunnel with test section air removal (plenum suction) was calibrated to a Mach number of 1.3. The results of the calibration, including the effects of slot shape modifications, test section wall divergence, and water vapor condensation, are presented. A complete description of the wind tunnel and its auxiliary equipment is included.

Corson, B. W., Jr.↗

Integrated Aeroservoelastic Optimization: Status and Direction

The interactions of lightweight flexible airframe structures, steady and unsteady aerodynamics, and wide-bandwidth active controls on modern airplanes lead to considerable multidisciplinary design challenges. More than 25 years of mathematical and numerical methods' development, numerous basic research studies, simulations and wind-tunnel tests of simple models, wind-tunnel tests of complex models of real airplanes, as well as flight tests of actively controlled airplanes, have all contributed to the accumulation of a substantial body of knowledge in the area of aeroservoelasticity. A number of analysis codes, with the capabilities to model real airplane systems under the assumptions of linearity, have been developed. Many tests have been conducted, and results were correlated with analytical predictions. A selective sample of references covering aeroservoelastic testing programs from the 1960s to the early 1980s, as well as more recent wind-tunnel test programs of real or realistic configurations, are included in the References section of this paper. An examination of references 20-29 will reveal that in the course of development (or later modification), of almost every modern airplane with a high authority active control system, there arose a need to face aeroservoelastic problems and aeroservoelastic design challenges.

Livne, Eli↗

Application of system identification to analytic rotor modeling from simulated and wind tunnel dynamic test data, part 2

An introduction to aircraft state and parameter identification methods is presented. A simplified form of the maximum likelihood method is selected to extract analytical aeroelastic rotor models from simulated and dynamic wind tunnel test results for accelerated cyclic pitch stirring excitation. The dynamic inflow characteristics for forward flight conditions from the blade flapping responses without direct inflow measurements were examined. The rotor blades are essentially rigid for inplane bending and for torsion within the frequency range of study, but flexible in out-of-plane bending. Reverse flow effects are considered for high rotor advance ratios. Two inflow models are studied; the first is based on an equivalent blade Lock number, the second is based on a time delayed momentum inflow. In addition to the inflow parameters, basic rotor parameters like the blade natural frequency and the actual blade Lock number are identified together with measurement bias values. The effect of the theoretical dynamic inflow on the rotor eigenvalues is evaluated.

Hohenemser, K. H.↗