Search NASA⌕ Search

SEARCH · Search NASA

Results for “damage threshold”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

A study of charged particles/radiation damage to VLSI device materials

Future spacecraft systems such as the manned space station will be subjected to low-dose long term radiation particles. Most electronic systems are affected by such particles. There is therefore a great need to understand device physics and failure mechanisms affected by radiation and to design circuits that would be less susceptible to radiation. Using 2 MeV electron radiation and bias temperature aging, it was found that MOS capacitors that were prepositively biased have lower flatband voltage shift and lesser increase in density of surface state charge than those that were not prepositively biased. In addition, it was shown that there is continued recovery of flatband voltage and density of state charge in irradiated capacitors during both room temperature anneal and 137 degree anneal. When nMOS transistors were subjected to 1 MeV proton radiation, charge pumping and current versus voltage measurements indicated that transconductance degradation, threshold voltage shifts and changes in interface states density may be the primary cause of nMOS transistor failure after radiation. Simulation studies using SPICE were performed on CMOS SRAM cells of various transistor sizes. It is shown that transistor sizing affects the noise margins of CMOS SRAM cells, and that as the beta ratio of the transistors of the CMOS SRAM cell decreases, the effective noise margin of the SRAM cell increases. Some suggestions were made in connection with the design of CMOS SRAMS that are hardened against single event upsets.

Okyere, John G.↗

Nanoscale patterning of graphene through femtosecond laser ablation

We report on nanometer-scale patterning of single layer graphene on SiO{sub 2}/Si substrate through femtosecond laser ablation. The pulse fluence is adjusted around the single-pulse ablation threshold of graphene. It is shown that, even though both SiO{sub 2} and Si have more absorption in the linear regime compared to graphene, the substrate can be kept intact during the process. This is achieved by scanning the sample under laser illumination at speeds yielding a few numbers of overlapping pulses at a certain point, thereby effectively shielding the substrate. By adjusting laser fluence and translation speed, 400 nm wide ablation channels could be achieved over 100 μm length. Raster scanning of the sample yields well-ordered periodic structures, provided that sufficient gap is left between channels. Nanoscale patterning of graphene without substrate damage is verified with Scanning Electron Microscope and Raman studies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of nanoscale interfaces on the dynamic deformation and spall failure of Cu–Fe alloy microstructures

Additively manufactured immiscible Cu–Fe alloys can exhibit a distribution of nanoscale interfaces due to the distribution of nanoscale clusters in the equilibrium and metastable phases. Molecular dynamics simulations investigate the role of such interfaces on the phase stability and transformation behavior during shock compression, as well as the mechanisms of damage nucleation during spall failure. The model multiphase Cu–Fe systems studied here comprise a distribution of Fe clusters in an FCC Cu matrix, as well as Cu clusters in a BCC Fe matrix. The length scales of the nanoscale clusters determine the energetics of the interfaces that can result in FCC/BCC (equilibrium) or FCC/FCC (metastable) interfaces in the Cu system matrix, and BCC/FCC (equilibrium) or BCC/BCC (metastable) interfaces in the Fe matrix. The MD simulations demonstrate that nanoscale metastable interface microstructures can induce plastic deformation and also stabilize phases or suppress phase transformations in metastable phase clusters. In contrast, equilibrium interfaces can influence phase transformation thresholds and serve as additional void nucleation sites during failure.

36 MATERIALS SCIENCE↗

An on-line acoustic fluorocarbon coolant mixture analyzer for the ATLAS silicon tracker

The ATLAS silicon tracker community foresees an upgrade from the present octafluoro-propane (C{sub 3}F{sub 8}) evaporative cooling fluid - to a composite fluid with a probable 10-20% admixture of hexafluoro-ethane (C{sub 2}F{sub 6}). Such a fluid will allow a lower evaporation temperature and will afford the tracker silicon substrates a better safety margin against leakage current-induced thermal runaway caused by cumulative radiation damage as the luminosity profile at the CERN Large Hadron Collider increases. Central to the use of this new fluid is a new custom-developed speed-of-sound instrument for continuous real-time measurement of the C{sub 3}F{sub 8}/C{sub 2}F{sub 6} mixture ratio and flow. An acoustic vapour mixture analyzer/flow meter with new custom electronics allowing ultrasonic frequency transmission through gas mixtures has been developed for this application. Synchronous with the emission of an ultrasound 'chirp' from an acoustic transmitter, a fast readout clock (40 MHz) is started. The clock is stopped on receipt of an above threshold sound pulse at the receiver. Sound is alternately transmitted parallel and anti-parallel with the vapour flow for volume flow measurement from transducers that can serve as acoustic transmitters or receivers. In the development version, continuous real-time measurement of C{sub 3}F{sub 8}/C{sub 2}F{sub 6} flow and calculation of the mixture ratio is performed within a graphical user interface developed in PVSS-II, the Supervisory, Control and Data Acquisition standard chosen for LHC and its experiments at CERN. The described instrument has numerous potential applications - including refrigerant leak detection, the analysis of hydrocarbons, vapour mixtures for semiconductor manufacture and anesthetic gas mixtures. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Acute phytotoxicity of seven metals alone and in mixture: Are Italian soil threshold concentrations suitable for plant protection?

Metals can pollute soils in both urban and rural areas with severe impacts on the health of humans, plants and animals living there. Information on metal toxicity is therefore important for ecotoxicology. This study investigated the phytotoxicity of different metals frequently found as pollutants in soils: arsenic, cadmium, chromium, lead, mercury, nickel and zinc. Cucumber (Cucumis sativus), sorghum (Sorghum saccharatum) and cress (Lepidium sativum) seeds were used as models for other plants used in human nutrition such as cereals, rice, fruits and vegetables. The 72-h germination rate and root elongations were selected as short-term ecotoxicological endpoints in seeds exposed to single metals and mixtures. Metals were spiked onto OECD standard soils in concentrations comparable to current Italian contamination threshold concentrations for residential and commercial soils. Arsenic, chromium, mercury and nickel were the most toxic metals in our experimental conditions, particularly to cress seeds (5.172, 152 and 255.4 mg/kg as 72 h IC50 for arsenic, mercury and nickel respectively). Italian limits were acceptable for plant protection only for exposure to each metal alone but not for the mixtures containing all the metals concentrations expected by their respective legislative threshold. The effects of the mixture were class-specific: trends were comparable in dicots but different in monocots. The response induced by the mixture at high concentrations differed from that theoretically obtainable by summing the effects of the individual metals. This might be due to partial antagonism of the metals in soil or to the formation of complexes between the metals, which reduce the bioavailability of the pollutants for plants. - Graphical abstract: Metals investigated: Arsenic, Cadmium, Chromium, Lead, Mercury, Nickel and Zinc. - Highlights: • The short-term phytotoxicity of seven metals was investigated with 3 higher plants. • Italian limits for arsenic and nickel in residential soils can damage plants. • Root elongation is heavily affected by metals. • Italian limits are not suitable for plant protection when metals are in mixture.

54 ENVIRONMENTAL SCIENCES↗

Suppression of photorefractive damage with aid of steady-state temperature gradient in nominally pure LiNbO{sub 3} crystals

Photorefractive damage (PRD) in as-grown, oxidized, and slightly reduced nominally pure LiNbO{sub 3}, and iron-doped crystals with different compositions has been studied with the closed-aperture Z-scan and pseudo-Z-scan techniques at uniform temperature distribution, as well as at a steady-state temperature gradient {nabla}T, created by two external thermoelectric elements in the transverse direction to the light beam trajectory. The most important experimental finding consists of the demonstration of the possibility of a full PRD suppression in nominally pure crystals with the aid of a relatively small temperature gradient (12.5-84 K/cm), if {nabla}T is above a threshold value specific for each crystal studied. The threshold {nabla}T{sub th} decreases significantly with the increase in the so-called bipolaron absorption band (center at 470-500 nm) in the optical spectra, and it is not correlated with the composition of the crystals within the studied range of compositions ([Li]/[Nb]=0.946-0.983). No any partial suppression of PRD was observed in iron-doped ([Fe]{>=}0.01 wt %) lithium niobate crystals, even at the largest temperature gradient (85 K/cm) used in our study. To explain these experimental results, we use theoretical model taking into account local changes of spontaneous polarization (i.e., polarization charge field) at photoionization of intrinsic defects (polarons, bipolarons, and hole polarons). It has been shown that a steady-state temperature gradient may induce a local thermoelectric current of light-induced charge carriers and their instant recombination, resulting in a decrease in the polarization space-charge field and hence, a light-induced refractive index change. The latter mechanism may induce the full PRD suppression, if macroscopic charge separation (space-charge field effect) gives insignificant contribution to the total light-induced electric field, as in as-grown and reduced nominally pure LiNbO{sub 3} crystals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Prognostics for Microgrid Components

Prognostics is the science of predicting future performance and potential failures based on targeted condition monitoring. Moving away from the traditional reliability centric view, prognostics aims at detecting and quantifying the time to impending failures. This advance warning provides the opportunity to take actions that can preserve uptime, reduce cost of damage, or extend the life of the component. The talk will focus on the concepts and basics of prognostics from the viewpoint of condition-based systems health management. Differences with other techniques used in systems health management and philosophies of prognostics used in other domains will be shown. Examples relevant to micro grid systems and subsystems will be used to illustrate various types of prediction scenarios and the resources it take to set up a desired prognostic system. Specifically, the implementation results for power storage and power semiconductor components will demonstrate specific solution approaches of prognostics. The role of constituent elements of prognostics, such as model, prediction algorithms, failure threshold, run-to-failure data, requirements and specifications, and post-prognostic reasoning will be explained. A discussion on performance evaluation and performance metrics will conclude the technical discussion followed by general comments on open research problems and challenges in prognostics.

Saxena, Abhinav↗

A new method for predicting hurricane rapid intensification based on co-occurring environmental parameters

Abstract Tropical cyclones (TCs) that undergo Rapid Intensification (RI) can pose serious socioeconomic threats and can potentially result in major damaging impacts along coastal areas. Considering the complexity of various physical mechanisms that play a role in RI and its relatively low probability of occurrence, predicting RI remains a major operational challenge. In this study, we propose a simple deterministic binary classification model based on the co-occurrence of environmental parameters (MCE) to predict an RI event. More specifically, the model determines the possibility of RI based on a simple count of the number of environmental predictors deemed favorable and unfavorable. We compare our model results to logistic regression (LR) and decision tree (DT) models, well-trained using the same set of environmental predictors. Results reveal that at an RI threshold of 30 kt, the MCE exhibits a critical success index score of 0.233 which is 14% higher than DT and LR model performances. When tested at multiple RI thresholds, the MCE displays relatively higher skill scores across multiple metrics. By simultaneously evaluating the favorability of predictors, the MCE is able to comparatively reduce the number of false alarms predicted when certain predictors are unfavorable toward RI. Interpreting these model results to gain a physical understanding of how co-occurring environmental parameters can affect RI, we highlight future directions for using models based on the MCE approach to understand and predict TC RI as well as other meteorological extremes.

54 ENVIRONMENTAL SCIENCES↗

Damage free Ar ion plasma surface treatment on In{sub 0.53}Ga{sub 0.47}As-on-silicon metal-oxide-semiconductor device

In this paper, we investigated the effect of in-situ Ar ion plasma surface pre-treatment in order to improve the interface properties of In{sub 0.53}Ga{sub 0.47}As for high-κ top-gate oxide deposition. X-ray photoelectron spectroscopy (XPS) and metal-oxide-semiconductor capacitors (MOSCAPs) demonstrate that Ar ion treatment removes the native oxide on In{sub 0.53}Ga{sub 0.47}As. The XPS spectra of Ar treated In{sub 0.53}Ga{sub 0.47}As show a decrease in the AsO{sub x} and GaO{sub x} signal intensities, and the MOSCAPs show higher accumulation capacitance (C{sub acc}), along with reduced frequency dispersion. In addition, Ar treatment is found to suppress the interface trap density (D{sub it}), which thereby led to a reduction in the threshold voltage (V{sub th}) degradation during constant voltage stress and relaxation. These results outline the potential of surface treatment for III-V channel metal-oxide-semiconductor devices and application to non-planar device process.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Radiation-Damage Resistance in Phyllosilicate Minerals From First Principles and Implications for Radiocesium and Strontium Retention in Soils

Accidental discharges of the hazardous nuclear fission products 137Cs+ and 90Sr2+ into the environment, such as during the Fukushima Dai-ichi nuclear accident, have repeatedly occurred throughout the nuclear age. Numerous studies of their fate and transport in soils and sediments have demonstrated their strong and selective binding to phyllosilicates such as clay minerals, primarily via cation exchange into interlayer sites. The locally concentrated amounts of these radioactive beta-emitters that can be found in these host minerals raises important questions regarding the long-term interplay and durability of radioisotope-clay association, which is not well known. This study goes beyond the usual short-term focus to address the permanence of radioisotope retention in clay minerals, by developing a general theoretical understanding of their resistance to defect creation. We report ab initio molecular dynamics (AIMD) calculations of the threshold displacement energy (TDE) of each symmetry-unique atomic specie comprising the unit cell of model vermiculite. The determined TDE values are material specific and radiation independent. We use them to estimate the probability of Frenkel pair creation via direct electron-ion collision, as could be induced by the passage of a high energy electron emitted during the beta-decay of 137Cs, 90Sr and daughter 90Y. For 137Cs and 90Sr, we found that the probability is about 36%, while for 90Y the probability is much higher with about 89%. The long-term retention picture that emerges is that decay will progressively alter the clay interlayer structure and charge, likely leading to delamination of the clay and re-release of residual parent isotopes. Future work examining the effect of Frenkel defect accumulation on the binding energy of parent and daughter radionuclides in the interlayer is thus justifiable, and potentially important for accurate long-term forecasting of radionuclide transport in the environment.

Environmental Molecular Sciences Laboratory↗

Evidence for anti-synergism between ion-assisted etching and in-plasma photoassisted etching of silicon in a high-density chlorine plasma

Etching of p-Si in 60 mTorr 10%Cl2/90%Ar Faraday-shielded inductively coupled high density plasmas was investigated under both ionassisted etching (IAE) and photoassisted etching (PAE) conditions. Real-time etching rates and after-etching Si surface chemical compositions were obtained by laser interferometry and vacuum-transfer x-ray photoelectron spectroscopy (XPS), respectively. Precisely controlled ion energy distributions (IEDs) were generated by applying pulsed negative DC bias on the conductive sample stage. Above a 36 eV threshold at a total flow rate of 250 SCCM, the IAE rate increased with the square root of the ion energy. In contrast to the DC bias, etching under RF bias did not exhibit a threshold ion energy because of the wide IED. XPS spectra revealed that the surface layer under PAE conditions had a significantly lower chlorine content, composed of only SiCl. Under IAE conditions, however, silicon dangling bonds (Si•), SiCl 2 , and SiCl 3 were found on the surface, in addition to SiCl, with a relative abundance of SiCl > SiCl 2 , and SiCl 3 . The absence of higher chlorides and Si• under PAE conditions suggested that vacuum ultraviolet photons and above threshold-energy ions interact with the surface very differently. By varying the duty cycle of the pulsed DC bias, it was found that the IAE rate scaled with the energetic ion dose, but only for low duty cycles. For higher duty cycles, the apparent IAE yield fell off with an increasing Cl coverage on the surface, as the duty cycle went up, which pointed to a negative synergy (antisynergism) between PAE and IAE as the explanation. This antisynergism was further supported by the observed decrease of the total etching rate with an increasing period of the pulsed DC bias. A plausible mechanism is that increasing the pulsing period causes more near-surface damage, creating more recombination centers that lead to a higher loss rate of electron-hole pairs through recombination, thereby reducing the PAE rate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Softening the Gap between Wöhler and Paris – New Approaches for Fatigue Analysis –

Fatigue analysis tools can vary across industries. For example, automotive engineers often use the Wöhler (S-N) approach to design for safe-life, while aerospace engineers prioritize damage tolerance and inspection intervals, relying instead on crack growth models such as Paris’ law. Although both approaches may deal with the control of cracks in similar materials, their analysis tools and material characterizations are fundamentally distinct. This divide mirrors the classic split between stress-based strength analysis and linear elastic fracture mechanics. However, modern nonlinear models that incorporate material softening, such as cohesive laws, blur this boundary and capture fracture behaviors across scales. This presentation describes the CF23 fatigue model, which uses cohesive softening to link S-N crack initiation with crack propagation rates. CF23 spans the full fatigue spectrum, from initial propagation transients to steady-state growth and threshold conditions, offering a unified framework that bridges Wöhler and Paris-based methodologies. Example applications include fatigue crack propagation transients in adhesive interfaces and skin/stiffener separation.

cohesive elements↗

An Overview of NASA's Risk of Cardiovascular Disease from Radiation Exposure

The association between high doses of radiation exposure and cardiovascular damage is well established. Patients that have undergone radiotherapy for primary cancers of the head and neck and mediastinal regions have shown increased risk of heart and vascular damage and long-term development of radiation-induced heart disease [1]. In addition, recent meta-analyses of epidemiological data from atomic bomb survivors and nuclear industry workers has also shown that acute and chronic radiation exposures is strongly correlated with an increased risk of circulatory disease at doses above 0.5 Sv [2]. However, these analyses are confounded for lower doses by lifestyle factors, such as drinking, smoking, and obesity. The types of radiation found in the space environment are significantly more damaging than those found on Earth and include galactic cosmic radiation (GCR), solar particle events (SPEs), and trapped protons and electrons. In addition to the low-LET data, only a few studies have examined the effects of heavy ion radiation on atherosclerosis, and at lower, space-relevant doses, the association between exposure and cardiovascular pathology is more varied and unclear. Understanding the qualitative differences in biological responses produced by GCR compared to Earth-based radiation is a major focus of space radiation research and is imperative for accurate risk assessment for long duration space missions. Other knowledge gaps for the risk of radiation-induced cardiovascular disease include the existence of a dose threshold, low dose rate effects, and potential synergies with other spaceflight stressors. The Space Radiation Program Element within NASA's Human Research Program (HRP) is managing the research and risk mitigation strategies for these knowledge gaps. In this presentation, we will review the evidence and present an overview of the HRP Risk of Cardiovascular Disease and Other Degenerative Tissue Effects from Radiation Exposure.

Patel, Zarana S.↗

Monte Carlo Analysis of Pion Contribution to Absorbed Dose from Galactic Cosmic Rays

Accurate knowledge of the physics of interaction, particle production and transport is necessary to estimate the radiation damage to equipment used on spacecraft and the biological effects of space radiation. For long duration astronaut missions, both on the International Space Station and the planned manned missions to Moon and Mars, the shielding strategy must include a comprehensive knowledge of the secondary radiation environment. The distribution of absorbed dose and dose equivalent is a function of the type, energy and population of these secondary products. Galactic cosmic rays (GCR) comprised of protons and heavier nuclei have energies from a few MeV per nucleon to the ZeV region, with the spectra reaching flux maxima in the hundreds of MeV range. Therefore, the MeV - GeV region is most important for space radiation. Coincidentally, the pion production energy threshold is about 280 MeV. The question naturally arises as to how important these particles are with respect to space radiation problems. The space radiation transport code, HZETRN (High charge (Z) and Energy TRaNsport), currently used by NASA, performs neutron, proton and heavy ion transport explicitly, but it does not take into account the production and transport of mesons, photons and leptons. In this paper, we present results from the Monte Carlo code MCNPX (Monte Carlo N-Particle eXtended), showing the effect of leptons and mesons when they are produced and transported in a GCR environment.

Aghara, S.K.↗

Comment on “How will induced seismicity in Oklahoma respond to decreased saltwater injection rates?” by C. Langenbruch and M. D. Zoback

The state of Oklahoma has experienced an unprecedented increase in earthquake activity since 2009, likely driven by large-scale wastewater injection operations. Statewide injection rates peaked in early 2015 and steadily decreased thereafter, approximately coinciding with collapsing oil prices and regulatory action. If seismic activity is primarily driven by fluid injection, a noticeable seismogenic response to the decrease in injection rates is expected. Langenbruch and Zoback suggest that “the probability of potentially damaging larger events, should significantly decrease by the end of 2016 and approach historic levels within a few years.” We agree that the rate of small earthquakes has decreased toward the second half of 2016. However, their specific predictions about seismic hazard require reexamination. We test the influence of the model parameters of Langenbruch and Zoback based on fits to observed seismicity distributions. The results suggest that a range of realistic aftershock decay rates and b values can lead to an increase in moderate earthquake probabilities from 37 to 80% in 2017 without any further alteration to the model. In addition, the observation that all four M ≥ 5 earthquakes to date occurred when injection rates were below the triggering threshold of Langenbruch and Zoback challenges the applicability of the model for the most societally significant events.

54 ENVIRONMENTAL SCIENCES↗

Study on the creep deformation behavior and characterization of 9Cr-1Mo-V-Nb steel at elevated temperatures

Highlights: • The true creep deformation mechanism has been found by an evaluation of threshold stresses. • The analysed creep data suggest that the rate-controlling mechanism of creep is dislocation climb. • Coarsening of the M{sub 23}C{sub 6} carbides has been observed at 650 °C and 700 °C during creep. In this study, creep tests were conducted on a set of specimens made from the same tube of T91 steel at different temperatures (600 °C, 650 °C and 700 °C) with the applied stresses ranging from 30 MPa to 180 MPa and rupture times from 28.7 to 7957 h for understanding the creep mechanism. The stress dependence of minimum creep rates exhibits a power law with different exponents were found to be 14.3, 11 and 4.6 at 600 °C, 650 °C and 700 °C, respectively. Activation energy of creep was determined to be ~573 kJ/mol, which is ~53% higher than that of the lattice self-diffusion in α-iron. Based on the stress exponents, the modified Bird-Murkherjee-Dorn (BMD) equation was used to find the threshold stresses which has shown the strongly dependent on the test temperature. After incorporating the threshold stress, true activation energy of creep was found to be decreased ~271 kJ/mol, which is equivalent to that of lattice-self diffusion in α-iron. This subsequently led to evaluation of true stress exponent ~4. The results of creep data suggest that the rate-controlling mechanism of creep is dislocation climb for T91 steel. Microstructural observation of T91 steel is mainly consisting of lath martensite structure with fine MX carbonitrides and M{sub 23}C{sub 6} carbides were characterized using the scanning and transmission electron microscopes. The stress dependence of creep rupture life has shown that the operating mechanism of creep is similar. Furthermore, creep data was analysed for validity of the Monkman-Grant relationship and creep damage tolerance parameter. The qualitative microstructure of the crept samples show that less number of MX carbonitrides within grains is responsible for creep cavity formation and decreasing the rupture life. Thus, microstructural degradation is attributed to M{sub 23}C{sub 6} carbides coarsened and dislocation sub-structure boundaries are mainly responsible for creep damage. The fracture morphology of the samples has revealed with dimples is a typical transgranular ductile failure.

36 MATERIALS SCIENCE↗

Multi-View Convolutional Neural Network for Data Spoofing Cyber-Attack Detection in Distribution Synchrophasors

Security of Distribution Synchrophasors Data (DSD) is of paramount importance as the data is used for critical smart grid applications including situational awareness, advanced protection, and dynamic control. Unfortunately, the DSD are attractive targets for malicious attackers aiming to damage grid. Data spoofing is a new class of deceiving attack, where the DSD of one Phasor Measurement Units (PMUs) is tampered by other PMUs thereby spoiling measurement based applications. In order to address this issue, a source authentication based data spoofing attack detection method is proposed using Multi-view Convolutional Neural Network (MCNN). First, common components embedded in raw frequency measurements from DSD are removed by Savitzky-Golay (SG) filter. Second, fast S transform (FST) is utilized to extract representative spatial fingerprints via time frequency analysis. Third, the spatial fingerprint is fed to MCNN, which combines dilated and standard convolutions for automatic feather extraction and source identification. Finally, according to the output of MCNN, spoofing attack detection is performed via threshold criterion. Extensive experiments with actual DSD from multiple locations in FNET/Grideye are conducted to verify the effectiveness of the proposed method.

97 MATHEMATICS AND COMPUTING↗

The mechanics of network polymers with thermally reversible linkages

Encapsulated printed circuit boards typically use conventional thermosetting polymers which are difficult to remove without damaging the electronics if upgrades are needed. To improve the efficiency of maintaining printed circuit boards, network polymers with thermally reversible linkages were developed to provide an alternative class of encapsulation thermosets that could be easily and non-destructively removed and later reapplied. These polymers include functionalities that dynamically break and form covalent bonds. Over time, the connectivity of the network evolves, which causes the macroscopic stress in the material to relax and the permanent shape to change even if these processes are in equilibrium. With respect to removal, the equilibrium behavior of these processes changes if the thermodynamic state of the material is changed, which alters the number density of chains. If the number density of chains is reduced below the percolation threshold, the material exhibits a gel-point transition beyond which, it behaves as a viscous liquid. These two properties contrast sharply with conventional thermosetting polymers, which do not exhibit this relaxation mechanism nor a gel-point transition.

Long, Kevin N.↗