Search NASA⌕ Search

SEARCH · Search NASA

Results for “evaluation process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Conclusions of the Capstone Depleted Uranium Aerosol Characterization and Risk Assessment Study

The rationale for the Capstone Depleted Uranium (DU) Aerosol Characterization and Risk Assessment Program and its results and applications have been examined in the previous 13 articles of this special issue. This paper summarizes the results and discusses its successes and lessons learned. The robust data from the Capstone DU Aerosol Study have provided a sound basis for assessing the inhalation exposure to DU aerosols and the dose and risk to personnel in combat vehicles at the time of perforation and to those entering immediately after perforation. The Human Health Risk Assessment provided a technically sound process for evaluating chemical and radiological doses and risks from DU aerosol exposure using well-accepted biokinetic and dosimetric models innovatively applied. An independent review of the study process and results is summarized, and recommendations for possible avenues of future study by the authors and by other major reviews of DU health hazards are provided.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Finite-range effects in (d,p) reactions

With the increasing interest in using (d,p) transfer reactions to extract structure and astrophysical information, it is important to evaluate the accuracy of common approximations in reaction theory. Starting from the zero-range adiabatic wave model, which takes into account deuteron breakup in the transfer process, we evaluate the importance of the finite range of the n-p interaction in calculating the adiabatic deuteron wave (as in Johnson and Tandy) as well as in evaluating the transfer amplitude. Our study covers a wide variety of targets, as well as a large range of beam energies. Whereas at low beam energies finite-range effects are small (below 10%), we find these effects to become important at intermediate energies (20 MeV/u) calling for an exact treatment of finite range in the analysis of (d,p) reactions measured at fragmentation facilities.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Atmospheric Pressure Synthesis of In2Se3, Cu2Se, and CuInSe2 without External Selenization from Solution Precursors

In{sub 2}Se{sub 3}, Cu{sub 2}Se, and CuInSe{sub 2} thin films have been successfully fabricated using novel metal organic decomposition (MOD) precursors and atmospheric pressure-based deposition and processing. The phase evolution of the binary (In-Se and Cu-Se) and ternary (Cu-In-Se) MOD precursor films was examined during processing to evaluate the nature of the phase and composition changes. The In-Se binary precursor exhibits two specific phase regimes: (i) a cubic-InxSey phase at processing temperatures between 300 and 400 C and (ii) the {gamma}-In{sub 2}Se{sub 3} phase for films annealed above 450 C. Both phases exhibit a composition of 40 at.% indium and 60 at.% selenium. The binary Cu-Se precursor films show more diverse phase behavior, and within a narrow temperature processing range a number of Cu-Se phases, including CuSe{sub 2}, CuSe, and Cu{sub 2}Se, can be produced and stabilized. The ternary Cu-In-Se precursor can be used to produce relatively dense CuInSe{sub 2} films at temperatures between 300 and 500 C. Layering the binary precursors together has provided an approach to producing CuInSe{sub 2} thin films; however, the morphology of the layered binary structure exhibits a significant degree of porosity. An alternative method of layering was explored where the Cu-Se binary was layered on top of an existing indium-gallium-selenide layer and processed. This method produced highly dense and large-grained (>3 {micro}m) CuInSe{sub 2} thin films. This has significant potential as a manufacturable route to CIGS-based solar cells.

14 SOLAR ENERGY↗

Spray combustion under oscillatory pressure conditions

The performance and stability of liquid rocket engines is often argued to be significantly impacted by atomization and droplet vaporization processes. In particular, combustion instability phenomena may result from the interactions between the oscillating pressure field present in the rocket combustor and the fuel and oxidizer injection process. Few studies have been conducted to examine the effects of oscillating pressure fields on spray formation and its evolution under rocket engine conditions. The pressure study is intended to address the need for such studies. In particular, two potentially important phenomena are addressed in the present effort. The first involves the enhancement of the atomization process for a liquid jet subjected to an oscillating pressure field of known frequency and amplitude. The objective of this part of the study is to examine the coupling between the pressure field and or the resulting periodically perturbed velocity field on the breakup of the liquid jet. In particular, transverse mode oscillations are of interest since such modes are considered of primary importance in combustion instability phenomena. The second aspect of the project involves the effects of an oscillating pressure on droplet coagulation and secondary atomization. The objective of this study is to examine the conditions under which phenomena following the atomization process are affected by perturbations to the pressure or velocity fields. Both coagulation and represent a coupling mechanism between the pressure field and the energy release process in rocket combustors. It is precisely this coupling which drives combustion instability phenomena. Consequently, the present effort is intended to provide the fundamental insights needed to evaluate these processes as important mechanisms in liquid rocket instability phenomena.

Jacobs, H. R.↗

Workability Limits of Magnesium Alloy AZ31B Subjected to Equal Channel Angular Pressing

Equal channel angular pressing (ECAP) is an important severe plastic deformation process to produce ultrafine grained microstructures in metals and alloys. Magnesium and its alloys generally possess poor workability at temperatures below 250 °C. This investigation examines the influence of different passes and processing routes of ECAP on improving the workability of Mg alloy AZ31B. ECAP was carried out for three passes using a die of angle 120° using processing routes Bc and C. The operating temperature was 523 K for the first pass and 423 K for the subsequent two passes. The resultant microstructure and mechanical properties were determined. Workability of the alloy at 423 K (150 °C) was determined using upsetting experiments on cylindrical specimens machined from the annealed and ECAPed samples. Workability limit diagrams have been constructed for the various processed conditions. The workability data generated were also analyzed using five different workability criteria (also referred to as ductile fracture models) and the material constants for these five models were evaluated. Specimens processed by two passes through route C (pass 2C) exhibits better workability compared to other passes since the workability limit line after this pass shows maximum safe working area and lies above the other workability lines. Among the five different workability criteria investigated, the Freudenthal workability criterion is more suitable for prediction of failure in this alloy.

36 MATERIALS SCIENCE↗

Evaluating Cytotoxicity and Cellular Uptake from the Presence of Variously Processed Ti02 Nanostructured Morphologies

We evaluated the cytotoxicity of various morphological classes of TiO{sub 2} nanostructures (including 0-D nanoparticles, 1-D nanorods, and 3-D assemblies) toward living cells. These TiO{sub 2} nanostructures were modified with fluorescent dye molecules, mediated via a dopamine linkage, in order to facilitate a confocal study of their internalization. Specifically, we noted that both TiO{sub 2} 1-D nanorods and 0-D nanoparticles could internalize into cells after 24 h of incubation time. However, only incubation with TiO{sub 2} 1-D nanorods and 3-D micrometer-scale sea urchin-like assemblies at concentrations of up to 125 {mu}g/mL yielded data suggestive of cell viabilities of close to 100%. Moreover, upon irradiation with UV light for periods of a few minutes at energy densities of up to 1 J/cm{sub 2}, we observed up to 60% mortality rates, indicative of the cytotoxic potential of photoirradiated TiO{sub 2} nanostructures due to the generation of reactive oxygen species.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Deployment and Evaluation of SciStream on OLCF's Advanced Computing Ecosystem (ACE)

The growing demand for real-time analysis, experimental steering, and decision-making in scientific workflows has created a need for tightly coupled integrations between experimental facilities and high-performance computing (HPC) systems. The Department of Energy’s Integrated Research Infrastructure (IRI) initiative highlights data streaming as a key capability for enabling memory-to-memory data transfers, bypassing the limitations of traditional store-and-forward models. SciStream is a toolkit developed by researchers at Argonne National Laboratory (ANL) to support such streaming by addressing cross-domain security, delegated authentication, and application transparency. We deployed and evaluated SciStream on the Oak Ridge Leadership Computing Facility’s (OLCF) Advanced Computing Ecosystem (ACE) infrastructure, leveraging the Olivine OpenShift cluster and its high-bandwidth Data Streaming Nodes (DSNs) as gateway nodes. Our evaluation included synthetic streaming workloads derived from IRI science workflows, a streaming simulator, and integration with RabbitMQ to handle low-level messaging. This report documents the deployment process, performance evaluation, and challenges encountered, along with opportunities for future improvements.

97 MATHEMATICS AND COMPUTING↗

US/Russian Joint Film Test

A joint U.S./Russian film test was conducted during MIR Mission 18 to evaluate the effects of radiation on photographic film during long-duration space flights. Two duplicate sets of film were flown on this MIR mission: one set was processed and evaluated by the NASA/JSC Photographic Laboratory, and the other by the RKK Energia's Photographic Laboratory in Moscow. This preliminary report includes only the results of the JSC evaluation (excluding the SN-10 film which was not available for evaluation at the time this report was written). The final report will include an evaluation by JSC of the SN-10 film and an evaluation of the test data by the RKK Energia. ISC's evaluation of the test data showed the positive film flown was damaged very little when exposed to approximately 8 rads of radiation. Two of the three negative films were significantly damaged and the third film was damaged only moderately.

Slater, Richard↗

ESD Reviews: Model Dependence in Multi-Model Climate Ensembles: Weighting, Sub-Selection and Out-Of-Sample Testing

The rationale for using multi-model ensembles in climate change projections and impacts research is often based on the expectation that different models constitute independent estimates; therefore, a range of models allows a better characterisation of the uncertainties in the representation of the climate system than a single model. However, it is known that research groups share literature, ideas for representations of processes, parameterisations, evaluation data sets and even sections of model code. Thus, nominally different models might have similar biases because of similarities in the way they represent a subset of processes, or even be near-duplicates of others, weakening the assumption that they constitute independent estimates. If there are near-replicates of some models, then treating all models equally is likely to bias the inferences made using these ensembles. The challenge is to establish the degree to which this might be true for any given application. While this issue is recognised by many in the community, quantifying and accounting for model dependence in anything other than an ad-hoc way is challenging. Here we present a synthesis of the range of disparate attempts to define, quantify and address model dependence in multi-model climate ensembles in a common conceptual framework, and provide guidance on how users can test the efficacy of approaches that move beyond the equally weighted ensemble. In the upcoming Coupled Model Intercomparison Project phase 6 (CMIP6), several new models that are closely related to existing models are anticipated, as well as large ensembles from some models. We argue that quantitatively accounting for dependence in addition to model performance, and thoroughly testing the effectiveness of the approach used will be key to a sound interpretation of the CMIP ensembles in future scientific studies.

Abramowitz, Gab↗

Butyric Acid Production from Delignified Corn Stover Using Thermophilic Bacterial Co-Cultures

Butyric acid (BA) is a valuable platform chemical in the food and pharmaceutical industries, and it is also a potential precursor for the production of biobutanol and sustainable aviation fuels (SAFs). BA is mainly synthesized from petroleum; thus, cost-effective, and sustainable alternatives for its production are attracting the interest of several sectors. The present work proposes a solids-to-acids bioprocess to produce BA from corn stover utilizing a co-culture that consists of two thermophilic bacteria, Clostridium thermocellum, a well-known efficient degrader of insoluble and oligomeric cellulosic substrates, and Clostridium thermobutyricum, a highly efficient BA producer from monomeric sugars. After initial proof of concept experiments, a series of optimization studies were carried out to evaluate the process limits of this co-culture. First, the co-cultivation of both microorganisms at different inoculum sizes in deacetylated and mechanically refined corn stover (DMR) was evaluated. No significant differences were found on the solids deconstruction and carbohydrates utilization among all the treatments. In addition, BA production was similar under all conditions, ranging between 2.1 and 2.4 g/L. Next, the deconstruction, and BA production capabilities of the co-culture at increased DMR solids contents (3, 4.5, and 6% (w/v)) were tested. Although no difference was observed in the solids deconstruction and carbohydrates utilization among treatments, BA production increased concomitantly to solids loading; the maximum values observed were 2.8, 3.6, and 6.2 g/L in the 3, 4.5, and 6% treatments, respectively. In fact, BA production did not reach its absolute maximum in the 6% treatment after 160 h of fermentation. Lastly, a fed-batch experiment was performed to investigate the co-culture capabilities and possible system constraints to achieve higher BA titers. Data on substrate modifications and product formation as well as on the growth of each microorganism will be shown. Results from this work demonstrate a promising bioprocess approach for the production of BA from lignocellulosic biomass using a thermophilic bacterial co-culture.

bacteria↗

Characterization of PMR polyimide resin and prepreg

Procedures for the chemical characterization of PMR-15 resin solutions and graphite-reinforced prepregs were developed, and a chemical data base was established. In addition, a basic understanding of PMR-15 resin chemistry was gained; this was translated into effective processing procedures for the production of high quality graphite composites. During the program the PMR monomers and selected model compounds representative of postulated PMR-15 solution chemistry were acquired and characterized. Based on these data, a baseline PMR-15 resin was formulated and evaluated for processing characteristics and composite properties. Commercially available PMR-15 resins were then obtained and chemically characterized. Composite panels were fabricated and evaluated.

Lindenmeyer, P. H.↗

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗

The kinetics of Al-Si spinel phase crystallization from calcined kaolin

The crystallization of Al-Si spinel from medium ordered kaolin with high content of kaolinite was investigated using the differential thermal analysis (DTA). The apparent activation energy of the process was evaluated from the dependence of exothermic peak of crystallization on heating rate. Within the applied interval of heating rate (1-40 K min{sup -1}) the temperature of peak maximum increases from initial value of 1220.5 K in about 54.2 K. The apparent activation energy of the process 856{+-}2 kJ mol{sup -1}was calculated using the Kissinger equation. The growth morphology of Al-Si spinel crystal was evaluated from the Avrami parameter. The average value of morphology parameter determined within the observed interval of heating rate is 3.08{+-}0.03. This value indicates that crystallization mechanism of Al-Si spinel phase proceeds by bulk nucleation of the new phase with constant number of nuclei and that the three-dimensional growth of crystals is controlled by the reaction rate on the phases interface. - Graphical abstract: Kinetics of crystallization of Al-Si spinel from calcined kaolin was investigated by the DTA using the Kissinger kinetic approach. The apparent activation energy and morphology parameter of the process is 856{+-}2 kJ mol{sup -1} and 3.08{+-}0.03, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computation Modeling and Assessment of Nanocoatings for Ultra Supercritical Boilers (Final Report)

Forced outages and boiler unavailability of coal-fired fossil plants is most often caused by fire-side corrosion of boiler waterwalls and tubing. Reliable coatings are required for Ultrasupercritical (USC) application to mitigate corrosion since these boilers will operate at a much higher temperatures and pressures than in supercritical (565° C @ 24 MPa) boilers. Computational modeling efforts have been undertaken to design and assess potential Fe-Cr-Ni-Al systems to produce stable nanocrystalline coatings that form a protective, continuous scale of either Al 2 O 3 or Cr 2 O 3 . The computational modeling results identified a new series of Fe-25Cr-40Ni with or without 10 wt.% Al nanocrystalline coatings that maintain long-term stability by forming a diffusion barrier layer at the coating/substrate interface. The computational modeling predictions of microstructure, formation of continuous Al 2 O 3 scale, inward Al diffusion, grain growth, and sintering behavior were validated with experimental results. Advanced coatings, such as MCrAl (where M is Fe, Ni, or Co) nanocrystalline coatings, have been processed using different magnetron sputtering deposition techniques. Several coating trials were performed and among the processing methods evaluated, the DC pulsed magnetron sputtering technique produced the best quality coating with a minimum number of shallow defects and the results of multiple deposition trials showed that the process is repeatable. The cyclic oxidation test results revealed that the nanocrystalline coatings offer better oxidation resistance, in terms of weight loss, localized oxidation, and formation of mixed oxides in the Al 2 O 3 scale, than widely used MCrAlY coatings. However, the ultra-fine grain structure in these coatings, consistent with the computational model predictions, resulted in accelerated Al diffusion from the coating into the substrate. An effective diffusion barrier interlayer coating was developed to prevent inward Al diffusion. The fire-side corrosion test results showed that the nanocrystalline coatings with a minimum number of defects have a great potential in providing corrosion protection. The coating tested in the most aggressive environment showed no evidence of coating spallation and/or corrosion attack after 1050 hours exposure. In contrast, evidence of coating spallation in isolated areas and corrosion attack of the base metal in the spalled areas were observed after 500 hours. These contrasting results after 500 and 1050 hours exposure suggest that the premature coating spallation in isolated areas may be related to the variation of defects in the coating between the samples. It is suspected that the cauliflower-type defects in the coating were presumably responsible for coating spallation in isolated areas. Thus, a defect free good quality coating is the key for the long-term durability of nanocrystalline coatings in corrosive environments. Thus, additional process optimization work is required to produce defect-free coatings prior to development of a coating application method for production parts.

01 COAL, LIGNITE, AND PEAT↗

Growth of new materials for solid state laser applications. The growth of ZnGeP2 by the vertical Bridgman method

This is the final technical report on the cooperative NASA program 'Growth of New Materials for Solid State Laser Applications,' covering the period from 9-1-86 through 3-31-91. The first two and one half years of the program, from 9-1-86 through 3-31-89, was devoted to the development of new eye-safe laser sources. Single crystal fibers of rare earth doped and co-doped YAG were grown by the laser-heated pedestal growth method, characterized for their structural properties and supplied to NASA/Langley for spectroscopic evaluation. From 4-1-89 though 3-31-91, research focused on the growth of zinc germanium phosphide for nonlinear optical applications in the IR. The vertical Bridgman growth process was evaluated as a means to achieve better control over the short wavelength optical absorption in this material that adversely affects 2 micron-pumped optical parametric oscillators.

Feigelson, R. S.↗

Conversion of plastic waste into high-value lubricants: techno-economic analysis and life cycle assessment

Given the low recycling rate of plastic waste in the United States due to low economic incentives, it is of great interest to develop a technology to upgrade plastic waste with favorable economics. Plastic upcycling to valuable chemicals could ensure a circular economy for plastics and reduce the environmental burden caused by their end use cycle and disposal. A conceptual facility to convert 250 metric ton (MT) per day of plastic waste was modeled; the main product was a high-quality liquid (HQL) with a similar performance to polyalphaolefin (PAO) lubricants. The modeled process had a lubricant yield of up to 90% based on the experimental results at the laboratory scale. Techno-economic analysis (TEA) and life cycle assessment (LCA) were also performed to evaluate the process economics and its environmental impact. By using a mixture of colored and natural high-density polyethylene (HDPE), the production cost was in the range of 0.6–1.98 dollars per kg of lubricant, depending on the operating conditions. The life cycle emissions were in the range of 0.48–1.2 kg CO 2e kg Lub -1 showing, for the best case scenario, a 52% reduction relative to the emissions for petroleum lubricants, and a 74% reduction relative to the emissions for PAO lubricants. Finally, the impacts of the lubricant yield, the catalyst amount, and reaction time were evaluated, and their effect on the final production cost was discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optical Calibration Process Developed for Neural-Network-Based Optical Nondestructive Evaluation Method

A completely optical calibration process has been developed at Glenn for calibrating a neural-network-based nondestructive evaluation (NDE) method. The NDE method itself detects very small changes in the characteristic patterns or vibration mode shapes of vibrating structures as discussed in many references. The mode shapes or characteristic patterns are recorded using television or electronic holography and change when a structure experiences, for example, cracking, debonds, or variations in fastener properties. An artificial neural network can be trained to be very sensitive to changes in the mode shapes, but quantifying or calibrating that sensitivity in a consistent, meaningful, and deliverable manner has been challenging. The standard calibration approach has been difficult to implement, where the response to damage of the trained neural network is compared with the responses of vibration-measurement sensors. In particular, the vibration-measurement sensors are intrusive, insufficiently sensitive, and not numerous enough. In response to these difficulties, a completely optical alternative to the standard calibration approach was proposed and tested successfully. Specifically, the vibration mode to be monitored for structural damage was intentionally contaminated with known amounts of another mode, and the response of the trained neural network was measured as a function of the peak-to-peak amplitude of the contaminating mode. The neural network calibration technique essentially uses the vibration mode shapes of the undamaged structure as standards against which the changed mode shapes are compared. The published response of the network can be made nearly independent of the contaminating mode, if enough vibration modes are used to train the net. The sensitivity of the neural network can be adjusted for the environment in which the test is to be conducted. The response of a neural network trained with measured vibration patterns for use on a vibration isolation table in the presence of various sources of laboratory noise is shown. The output of the neural network is called the degradable classification index. The curve was generated by a simultaneous comparison of means, and it shows a peak-to-peak sensitivity of about 100 nm. The following graph uses model generated data from a compressor blade to show that much higher sensitivities are possible when the environment can be controlled better. The peak-to-peak sensitivity here is about 20 nm. The training procedure was modified for the second graph, and the data were subjected to an intensity-dependent transformation called folding. All the measurements for this approach to calibration were optical. The peak-to-peak amplitudes of the vibration modes were measured using heterodyne interferometry, and the modes themselves were recorded using television (electronic) holography.

Decker, Arthur J.↗

Measurement of the electroweak top quark production cross section and the CKM matrix element Vtb with the D0 experiment

At particle accelerators the Standard Model has been tested and will be tested further to a great precision. The data analyzed in this thesis have been collected at the world's highest energetic-collider, the Tevatron, located at the Fermi National Accelerator Laboratory (FNAL) in the vicinity of Chicago, IL, USA. There, protons and antiprotons are collided at a center-of-mass energy of {radical}s = 1.96 TeV. The discovery of the top quark was one of the remarkable results not only for the CDF and D0 experiments at the Tevatron collider, but also for the Standard Model, which had predicted the existence of the top quark because of symmetry arguments long before already. Still, the Tevatron is the only facility able to produce top quarks. The predominant production mechanism of top quarks is the production of a top-antitop quark pair via the strong force. However, the Standard Model also allows the production of single top quarks via the electroweak interaction. This process features the unique opportunity to measure the |V tb | matrix element of the Cabbibo-Kobayashi-Maskawa (CKM) matrix directly, without assuming unitarity of the matrix or assuming that the number of quark generations is three. Hence, the measurement of the cross section of electroweak top quark production is more than the technical challenge to extract a physics process that only occurs one out of ten billion collisions. It is also an important test of the V-A structure of the electroweak interaction and a potential window to physics beyond the Standard Model in the case where the measurement of |V{sub tb}| would result in a value significantly different from 1, the value predicted by the Standard Model. At the Tevatron two production processes contribute significantly to the production of single top quarks: the production via the t-channel, also called W-gluon fusion, and the production via the s-channel, known as well as W* process. This analysis searches for the combined s+t channel production cross section, assuming the ratio of s-channel production over t-channel production is realized in nature as predicted by the Standard Model. A data set of approximately 1 fb -1 is analyzed, the data set used by the D0 collaboration to claim evidence for single top quark production. Events with two, three, and four jets are used in the analysis if they contain one or two jets that were tagged as originating from the decay of a b hadron, an isolated muon or electron, and a significant amount of missing transverse energy. This selection of events follows the signature that the single top quark events are expected to show in the detector. In the meantime, both collaborations D0 and CDF have analyzed a larger data set and have celebrated the joint observation of single top quark production. The novelty of the analysis presented here is the way discriminating observables are determined. A so-called Multi-Process Factory evaluates each event under several hypotheses. A common analysis technique for example in top quark properties studies is to reconstruct the intermediate particles in the decay chain of the signal process from the final state objects measured in the various subdetectors. An essential part of such a method is to resolve the ambiguities that arise in the assignment of the final state objects to the partons of the decay chain. In a Multi-Process Factory this approach is extended and not only the decay chain of the signal process is reconstructed, but also the decay chains of the most important background processes. From the numerous possible event configurations for each of the signal and background decay chains the most probable configuration is selected based on a likelihood measure. Properties of this configuration, such as mass of the reconstructed top quark, are then used in a multivariate analysis technique to separate the expected signal contribution from the background processes. The technique which is used is called Boosted Decision Trees and has only recently been introduced in high energy physics analyses. A Bayesian approach is used to finally extract the cross section from the discriminant output of Boosted Decision Trees.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗