SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Planar visualization images are recorded of transverse jet mixing in a supersonic combustor flowfield, without chemical reaction, using laser-induced fluorescence from iodine molecules. Digital image processing and three-dimensional display enable complete representations of fuel penetration boundary and shock surfaces corresponding to several injection geometries and pressures.
Six airfoil interferograms were evaluated using a semiautomatic image-processor system which digitizes, segments, and extracts the fringe coordinates along a polygonal line. The resulting fringe order function was converted into density and pressure distributions and a comparison was made with pressure transducer data at the same wind tunnel test conditions. Three airfoil shapes were used in the evaluation to test the capabilities of the image processor with a variety of flows. Symmetric, supercritical, and circulation-control airfoil interferograms provided fringe patterns with shocks, separated flows, and high-pressure regions for evaluation. Regions along the polygon line with very clear fringe patterns yielded results within 1% of transducer measurements, while poorer quality regions, particularly near the leading and trailing edges, yielded results that were not as good.
Six airfoil interferograms were evaluated using a semiautomatic image-processor system which digitizes, segments, and extracts the fringe coordinates along a polygonal line. The resulting fringe order function was converted into density and pressure distributions and a comparison was made with pressure transducer data at the same wind tunnel test conditions. Three airfoil shapes were used in the evaluation to test the capabilities of the image processor with a variety of flows. Symmetric, supercritical, and circulation-control airfoil interferograms provided fringe patterns with shocks, separated flows, and high-pressure regions for evaluation. Regions along the polygon line with very clear fringe patterns yielded results within 1 percent of transducer measurements, while poorer quality regions, particularly near the leading and trailing edges, yielded results that were not as good.
The formation of scour patterns at bridge piers is driven by the forces at the boundary of the water flow. In most experimental scour studies, indirect processes have been applied to estimate the shear and normal stress using measured velocity profiles. The estimations are based on theoretical models and associated assumptions. However, the turbulence flow fields and boundary layer in the pier-scour region are very complex. In addition, available turbulence models cannot account accurately for the bed roughness effect. Direct measurement of the boundary shear and normal stress and their fluctuations are attractive alternatives. However, this approach is a challenging one especially for high spatial resolution and high fidelity measurements. The authors designed and fabricated a prototype miniature shear stress sensor including an EDM machined floating plate and a high-resolution laser optical encoder. Tests were performed both in air as well as operation in water with controlled flow. The sensor sensitivity, stability and signal-to-noise level were measured and evaluated. The detailed test results and a discussion of future work will be presented in this paper.
The formation of scour patterns at bridge piers is driven by the forces at the boundary of the water flow. In most experimental scour studies, indirect processes have been applied to estimate the shear and normal stress using measured velocity profiles. The estimations are based on theoretical models and associated assumptions. However, the turbulence flow fields and boundary layer in the pier-scour region are very complex. In addition, available turbulence models cannot account accurately for the bed roughness effect. Direct measurement of the boundary shear and normal stress and their fluctuations are attractive alternatives. However, this approach is a challenging one especially for high spatial resolution and high fidelity measurements. The authors designed and fabricated a prototype miniature shear stress sensor including an EDM machined floating plate and a high-resolution laser optical encoder. Tests were performed both in air as well as operation in water with controlled flow. The sensor sensitivity, stability and signal-to-noise level were measured and evaluated. The detailed test results and a discussion of future work will be presented in this paper.
The central focus of this research is to establish key scientific concepts that govern the selection of cellular and dendritic patterns during the directional solidification of alloys. Ground-based studies have established that the conditions under which cellular and dendritic microstructures form are precisely where convection effects are dominant in bulk samples. Thus, experimental data can not be obtained terrestrially under pure diffusive regime. Furthermore, reliable theoretical models are not yet possible which can quantitatively incorporate fluid flow in the pattern selection criterion. Consequently, microgravity experiments on cellular and dendritic growth are designed to obtain benchmark data under diffusive growth conditions that can be quantitatively analyzed and compared with the rigorous theoretical model to establish the fundamental principles that govern the selection of specific microstructure and its length scales. In the cellular structure, different cells in an array are strongly coupled so that the cellular pattern evolution is controlled by complex interactions between thermal diffusion, solute diffusion and interface effects. These interactions give infinity of solutions, and the system selects only a narrow band of solutions. The aim of this investigation is to obtain benchmark data and develop a rigorous theoretical model that will allow us to quantitatively establish the physics of this selection process.
A particularly favorable radial lineup between spacecraft in Earth orbit and Pioneers 10 and 11 (near the ecliptic plane at approximately 5.5 AU and approximately 4.5 AU, respectively) occurred in mid-1974, when the solar corona was in a stable and well-defined warped-dipole configuration. The radial alignment study reported here differs from previous applications of the technique in two respects: (1) It is the first time a two-dimensional (2-D) MHD model has been tested over such a lengthy propagation interval; the 2-D capability is crucial for treatment of the nonradial shearing motions occurring across the stream interface. (2) The three-dimensional (3-D) structure observed in the white light corona at that time is related to the systematic patterns of nonradial flow deflections appearing at the Pioneer corotating interaction region (CIR) fronts. Comparison of predicted and observed flows for pairs of streams in two successive rotations reveals that when the parent coronal hole projects far across the solar equator in a predominantly north-south orientation (i.e., nearest the 2-D idealization), the mapping is accurate down to details of the flow structures. But where the spacecraft tracks along a latitudinal boundary of a hole or the associated stream front is inclined at a shallow angle to the equator, the numerical projections deviate systematically from the observations. Among the sources of error are 3-D dynamical interactions neglected in the model, differential rotation effects, and slow temporal evolution of the coronal structures. A characteristic pattern of north-south and east-west deflections indicative of the 3-D geometry appears across the CIRs, but these patterns evidently reflect primarily the local, as opposed to global, orientation of the 3-D stream fronts. Such patterns appear common in CIRs observed by Pioneer during this period. These findings thus hold special relevance for the analysis of Ulysses observations, since the present coronal configuration is similar to that of 1974.
A comprehensive study for the inviscid numerical calculation of the hypersonic flow past a class of elliptic-cone derived waveriders is presented. The theoretical background associated with hypersonic small-disturbance theory (HSDT) is reviewed. Several approximation formulas for the waverider compression surface are established. A CFD algorithm is used to calculate flow fields for the on-design case and a variety of off-design cases. The results are compared with HSDT, experiment, and other available CFD results. For the waverider shape used in previous investigations, the bow shock for the on-design condition stands off from the leading-edge tip of the waverider. It was found that this occurs because the tip was too thick according to the approximating shape formula that was used to describe the compression surface. When this was corrected, the bow shock became closer to attached as it should be. At Mach numbers greater than the design condition, a lambda-shock configuration develops near the tip of the compression surface. At negative angles of attack, other complicated shock patterns occur near the leading-edge tip. These heretofore unknown flow patterns show the power and utility of CFD for investigating novel hypersonic configurations such as waveriders.
We present our numerical results for certain unsteady flows past oscillating cylinders and aerofoils. The computations are based on the stabilized space-time finite element formulation. The implicit equation systems resulting from the space-time finite element discretizations are solved using iterative solution techniques. One of the problems studied is flow past a cylinder which is forced to oscillate in the horizontal direction. In this case we observe a change from an unsymmetric mode of vortex shedding to a symmetric one. An extensive study was carried out for the case in which a cylinder is mounted on lightly damped springs and allowed to oscillate in the vertical direction. In this case the motion of the cylinder needs to be determined as part of the solution, and under certain conditions this motion changes the vortex-shedding pattern of the flow field significantly. This nonlinear fluid-structure interaction exhibits certain interesting behavior such as 'lock-in' and 'hysteresis', which are in good agreement with the laboratory experiments carried out by other researchers in the past. Preliminary results for flow past a pitching aerofoil are also presented.
Numerical simulations and wind tunnel experiments were performed to investigate flow separation and its control over a wall-mounted hump model. Three-dimensional, unsteady fluid dynamic simulations were used to capture the relevant flow physics of unsteady flow separation and its control via active and passive flow control methods. Surface pressure measurements and surface oilflow visualization were obtained in the experiments. Current measurements documented a considerably thinner incoming boundary layer, but similar pressure distribution, compared to the reference data reported in the CFD (Computational Fluid Dynamics) Validation (CFDVAL 2004) Experiments. Consistent with the data available in the literature, numerical simulations predicted a longer separation bubble, which manifested itself as a shift in the pressure distributions. Streamwise vortices generated by passive vortex generators increased the suction pressure and provided substantial pressure recovery. Numerical simulations of vortex generators qualitatively predicted the effects of control, and revealed patterns of attached/separated flow regions. On the other hand, active flow control using steady discrete jets reduced, but was not able to eliminate, flow separation for the tested configuration. Although the major disagreement between the numerical and experimental results was in the pressure recovery region due to the inaccurate prediction of separation bubbles, the relative pressure recoveries from the baselines were comparable. Surface oilflow visualization and simulated surface streamlines were qualitatively in good agreement revealing the key flow features.
An interhemispheric plasma transport model is used to study the flow characteristics of H(+), He(+), and O(+) along closed geomagnetic field lines for solstice conditions. The model corresponds to a time-dependent solution of the coupled continuity, momentum, and energy equations for the ions and electrons. The equations are solved along an entire flux tube from 120 km in one hemisphere to 120 km in the other hemisphere. The calculations are carried out for noon conditions for the flux tube passsing through Millstone Hill, at L = 3.2. The main conclusion is that H(+)-He(+) counterstreaming can be expected along a large segment of a plasmaspheric flux tube at solstice. For both symmetric and asymmetric wind patterns, the He(+) flow is from the winter to the summer ionosphere not only in the steady state, but during flux tube refilling due to the winter helium bulge and the depletion of N2.
BWB Aircraft with embedded engines and BLI inlets offer attractive advantages in terms of reduced noise from engines and increased range and fuel economy. The BLI inlet produces inlet distortion patterns that can reduce fan performance and stall margin, and can produce undesirable forced responses. Knowledge of the dynamic response of fan flow when subjected to flow distortions of the type produced by BLI inlets is important for the design of distortion tolerant fans. This project is investigating fan response to flow distortion by measuring the response of the fan of a JT15D engine to a flow pattern following the results of the NASA Inlet A BLI wind tunnel tests.
An investigation of vane-induced flow rotation to modify distorted steady-state total-pressure patterns in the subsonic diffuser of a supersonic mixed-compression inlet was conducted. Radial static-pressure gradients generated by the rotation was the mechanism used to modify the total-pressure distributions. Significant redistribution of circumferential distortion patterns into more compatible radial patterns was realized, but flow problems near the duct walls reduced the general effectiveness of the technique. Total-pressure losses associated with the swirl vanes were slight. Limited turbulence data indicated that vane istallation resulted in reduced turbulence levels.
Chevron mixing devices are used to reduce noise from commercial separate-flow turbofan engines. Mechanical chevron serrations at the nozzle trailing edge generate axial vorticity that enhances jet plume mixing and consequently reduces far-field noise. Fluidic chevrons generated with air injected near the nozzle trailing edge create a vorticity field similar to that of the mechanical chevrons and allow more flexibility in controlling acoustic and thrust performance than a passive mechanical design. In addition, the design of such a system has the future potential for actively controlling jet noise by pulsing or otherwise optimally distributing the injected air. Scale model jet noise experiments have been performed in the NASA Langley Low Speed Aeroacoustic Wind Tunnel to investigate the fluidic chevron concept. Acoustic data from different fluidic chevron designs are shown. Varying degrees of noise reduction are achieved depending on the injection pattern and injection flow conditions. CFD results were used to select design concepts that displayed axial vorticity growth similar to that associated with mechanical chevrons and qualitatively describe the air injection flow and the impact on acoustic performance.
Based on the hypothesis that patterns of skin-friction lines and external streamlines reflect the properties of continuous vector fields, topology rules define a small number of singular points (nodes, saddle points, and foci) that characterize the patterns on the surface and on particular projections of the flow (e.g., the crossflow plane). The restricted number of singular points and the rules that they obey are considered as an organizing principle whose finite number of elements can be combined in various ways to connect together the properties common to all steady three dimensional viscous flows. Introduction of a distinction between local and global properties of the flow resolves an ambiguity in the proper definition of a three dimensional separated flow. Adoption of the notions of topological structure, structural stability, and bifurcation provides a framework to describe how three dimensional separated flows originate and succeed each other as the relevant parameters of the problem are varied.
Optimal air traffic control coordinating flow and holding patterns of aircraft landing in single runway using linear-quadratic technique
Space shuttle aerothermodynamics, discussing heat transfer measurements, phase change patterns, electron beam flow visualization and boundary layer transition
Polycrystalline GaAs ribbons have been grown in graphite boats by passage of a wide zone through B2O3 encapsulated feed stock, confined by a quartz cover plate. By controlling the heat flow in the graphite boat and controlling the zoning rate, large grained, single phase polycrystalline samples with directional solidification and good thickness control were achieved. Arsenic vaporization was effectively suppressed at the melting point of GaAs by the B2O3 moat and 3 atmospheres of pressure. A vertical constrained-zone-melting apparatus with a B2O3 moat seal, rf heating, and water cooling on the bottom will be used to control the heat flow and temperature patterns required for growth of single crystal ribbons.