Search NASA⌕ Search

SEARCH · Search NASA

Results for “geometry optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Advanced Compressors for CO2-Based Power Cycles and Energy

Pumped thermal energy storage (PTES) is a cost-effective method for grid-scale, long-duration electrical energy storage (LDES). PTES uses a heat pump cycle to transfer thermal energy from a low temperature reservoir (LTR) to a high temperature reservoir (HTR), later using a heat engine cycle to reverse the process. A key component of the PTES system, the heat pump compressor, represents a significant driver to the cost, performance and operating characteristics of the PTES system. For grid-scale charging (>100 MW), traditional compressor scaling charts indicate that the operating conditions needed would be best served by a multistage axial compressor. While frame gas turbine compressors at these power ratings exist and operate at higher pressure ratios than needed for the CO2 PTES system, the inlet pressure and fluid density of this application exceed experience values. A conceptual design of a large-scale CO2 axial compressor was completed, including mean-line estimates of the compressor performance at full power conditions. The results of the conceptual design were used to refine the PTES cycle design, and updated operating conditions provided for further aero design optimization. A roughly one third scale of the first three stages of the 100 MW compressor was designed, built, and tested at relevant PTES charging conditions. Results of this test program are compared against high-resolution computational fluid dynamics models.

Compressor Heat↗

NBI optimization on SMART and implications for scenario development

Abstract The SMall Aspect Ratio Tokamak (SMART) under commissioning at the University of Seville, Spain, aims to explore confinement properties and possible advantages in confinement for compact/spherical tokamaks operating at negative vs. positive triangularity. This work explores the benefits of auxiliary heating through Neutral Beam Injection (NBI) for SMART scenarios beyond the initial Ohmic phase of operations, in support of the device’s mission. Expected values of electron and ion temperature achievable with NBI heating are first predicted for the current flat-top phase, including modeling to optimize the NBI injection geometry to maximize NBI absorption and minimize losses for a given equilibrium. Simulations are then extended for a selected case to cover the current ramp-up phase. Differences with results obtained for the flat-top phase indicate the importance of determining the plasma evolution over time, as well as self-consistently determining the edge plasma parameters for reliable time-dependent simulations. Initial simulation results indicate the advantage of auxiliary NBI heating to achieve nearly double values of pressure and stored energy compared to Ohmic discharges, thus significantly increasing the device’s performance. The scenarios developed in this work will also contribute to diagnostic development and optimization for SMART, as well as providing test cases for initial predictions of macro- and micro-instabilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Phase II Final Report Computer Optimization of Electron Guns

This program implemented advanced computer optimization into an adaptive mesh, finite element, 3D, charged particle code. The routines can optimize electron gun performance to achieve a specified current, beam size, and perveance. It can also minimize beam ripple and electric field gradients. The magnetics optimization capability allows design of coil geometries and magnetic material configurations to achieve a specified axial magnetic field profile. The optimization control program, built into the charged particle code Beam Optics Analyzer (BOA) utilizes a 3D solid modeling package to modify geometry using design tables. Parameters within the graphical user interface (currents, voltages, etc.) can be directly modified within BOA. The program implemented advanced post processing capability for the optimization routines as well as the user. A Graphical User Interface allows the user to set up goal functions, select variables, establish ranges of variation, and define performance criteria. The optimization capability allowed development of a doubly convergent multiple beam gun that could not be designed using previous techniques.

43 PARTICLE ACCELERATORS↗

Development of a high-temperature Inconel 625 heat exchanger by model design and binder jetting additive manufacturing

A nickel-based Inconel 625 superalloy heat exchanger for high-temperature applications was developed via binder jetting additive manufacturing. The material properties were characterized first on printed and sintered parts. Two sintering temperatures were used to investigate the effects of the temperature on densification and microstructure. For channel geometry design, the heat transfer capabilities of the heat exchanger were optimized for the cross-section geometry of fluid flow channels in a counterflow configuration, and a stress analysis was conducted to investigate the effects of channel geometry. After headers were incorporated into the heat exchanger as a one-piece component, a prototype was printed. A complete depowdering was achieved via compressed air blowing, and sintering was performed with the developed profile. Ultimately, a one-piece heat exchanger with a nearly full density was obtained. Heat transfer tests were performed on this unit, and the results were compared with those from the simulations. In this study, systematic processes were developed for an additively manufactured Inconel-based heat exchanger for high-pressure, high-temperature heat transfer applications.

36 MATERIALS SCIENCE↗

Hydrogen Adsorption, Dissociation and Diffusion on the α-U(001) Surface

First-principles pseudopotential plane wave calculations based on density functional theory and the generalized gradient approximation have been used to study the adsorption, dissociation, and diffusion of hydrogen on the α-U(001) surface. Weak molecular chemisorption was observed for H2 approaching with its molecular axis parallel to the surface. The optimization of the adsorption geometries on the threefold hollow sites yields final configurations with H2 molecules move towards the top site at both coverages of 0.25 and 0.5 monolayer. A low dissociation barrier of 0.081 eV was determined for H2 dissociated from onefold top site with the H atoms falling into the two adjacent threefold hollow sites. The density of states analysis along the dissociation paths show that the hybridization of U 5f and H 1s states only occurs when H2 molecule is dissociated.

08 HYDROGEN↗

Laser Brazing of High Temperature Braze Alloy

The Space Shuttle Main Engine (SSME) consists of 1080 conical tubes, which are furnace brazed themselves, manifolds, and surrounding structural jacket making almost four miles of braze joints. Subsequent furnace braze cycles are performed due to localized braze voids between the coolant tubes. SSME nozzle experiences extremely high heat flux (180 mW/sq m) during hot fire. Braze voids between coolant tubes may result in hot combustion gas escape causing jacket bulges. The nozzle can be disqualified for flight or result in mission failure if the braze voids exceed the limits. Localized braze processes were considered to eliminate braze voids, however, damage to the parent materials often prohibited use of such process. Being the only manned flight reusable rocket engine, it has stringent requirement on the braze process. Poor braze quality or damage to the parent materials limits the nozzle service life. The objective of this study was to develop a laser brazing process to provide quality, localized braze joints without adverse affect on the parent materials. Gold (Au-Cu-Ni-Pd-Mn) based high temperature braze alloys were used in both powder and wire form. Thin section iron base superalloy A286 tube was used as substrate materials. Different Laser Systems including CO2 (10.6 micrometers, 1kW), ND:YAG (1.06 micrometers, 4kW). and direct diode laser (808nm. 150W) were investigated for brazing process. The laser process variables including wavelength. laser power, travel speed and angle of inclination were optimized according to bead geometry and braze alloy wetting at minimum heat input level, The properties of laser brazing were compared to that of furnace brazing. Microhardness profiles were used for braze joint property comparison between laser and furnace brazing. The cooling rate of laser brazing was compared to furnace brazing based on secondary dendritic arm spacing, Both optical and Scanning Electron Microscope (SEM) were used to evaluate the microstructures of the braze materials and tube substrate. Metallography of the laser braze joint was compared to the furnace braze. SEM Energy Disperse X-Ray Spectra (EDX) and back scattered imaging were used to analyze braze alloy segregation. Although all of the laser systems, CO2, ND:YAG, and direct diode laser produced good braze joint, the direct diode laser was selected for its system simplicity, compactness and portability. Excellent laser and braze alloy coupling is observed with powder alloy compared to braze alloy wire. Good wetting is found with different gold based braze alloys. The laser brazing process can be optimized so that the adverse affect on the parent materials can be eliminated. Metallography of the laser braze joint has shown that quality braze joint was produced with laser brazing process. Penetration of the laser braze to the substrate is at neglectable level. Zero penetration is observed. Microstructure examinations shown that no observable changes of the microstructure (grain structure and precipitation) in the HAZ area between laser braze and furnace braze. Wide gaps can be laser brazed with single pass for up to 0.024 inches. Finer dendritic structure is observed in laser brazing compared with equiaxial and coarser grain of the furnace brazing microstructure. Greater segregation is also found in the furnace braze. Higher hardness of the laser braze joint comparing to furnace braze is observed due to the fast cooling rate and Finer microstructure in the laser brazing. Laser braze joint properties meet or exceed the furnace joint properties. Direct diode laser for thin section tube brazing with high temperature braze alloys have been successfully demonstrated. The laser's high energy density and precise control has shown significant advantages in reducing process heat input to the substrates and provide high quality braze joints comparing to other localized braze process such as torch, TIG, and MPTA processes. Significant cost savings can be realized particularly with localized braze comparing to a full furnace braze cycle.

Gao, Y. P.↗

SU-F-J-66: Anatomy Deformation Based Comparison Between One-Step and Two-Step Optimization for Online ART

Purpose: This study investigated that how the quality of adapted plan was affected by inter-fractional anatomy deformation by using one-step and two-step optimization for on line adaptive radiotherapy (ART) procedure. Methods: 10 lung carcinoma patients were chosen randomly to produce IMRT plan by one-step and two-step algorithms respectively, and the prescribed dose was set as 60 Gy on the planning target volume (PTV) for all patients. To simulate inter-fractional target deformation, four specific cases were created by systematic anatomy variation; including target superior shift 0.5 cm, 0.3cm contraction, 0.3 cm expansion and 45-degree rotation. Based on these four anatomy deformation, adapted plan, regenerated plan and non-adapted plan were created to evaluate quality of adaptation. Adapted plans were generated automatically by using one-step and two-step algorithms respectively to optimize original plans, and regenerated plans were manually created by experience physicists. Non-adapted plans were produced by recalculating the dose distribution based on corresponding original plans. The deviations among these three plans were statistically analyzed by paired T-test. Results: In PTV superior shift case, adapted plans had significantly better PTV coverage by using two-step algorithm compared with one-step one, and meanwhile there was a significant difference of V95 by comparison with adapted and non-adapted plans (p=0.0025). In target contraction deformation, with almost same PTV coverage, the total lung received lower dose using one-step algorithm than two-step algorithm (p=0.0143,0.0126 for V20, Dmean respectively). In other two deformation cases, there were no significant differences observed by both two optimized algorithms. Conclusion: In geometry deformation such as target contraction, with comparable PTV coverage, one-step algorithm gave better OAR sparing than two-step algorithm. Reversely, the adaptation by using two-step algorithm had higher efficiency and accuracy as target occurred position displacement. We want to thank Dr. Lei Xing and Dr. Yong Yang in the Stanford University School of Medicine for this work. This work was jointly supported by NSFC (61471226), Natural Science Foundation for Distinguished Young Scholars of Shandong Province (JQ201516), and China Postdoctoral Science Foundation (2015T80739, 2014M551949).

60 APPLIED LIFE SCIENCES↗

Deep reinforcement learning to discover multi-fuel injection strategies for compression ignition engines

Over the past several decades, regulation of compression ignition engine emissions has become increasingly stringent as concern about the environmental and health implications of these emissions has grown. These changing constraints have led to a series of new, alternative fuel injection strategies that aim to maintain power output while reducing in-cylinder generated emissions by operating in the low-temperature combustion (LTC) regime. These advanced injection strategies are created and retuned for individual combinations of engine geometry, fuel, and emissions constraints. Deep reinforcement learning has been shown to be an effective alternative to traditional optimization approaches for highly combinatorial control problems, such as discovering the optimal injection schedules for compression ignition engines. In this study, we deploy a previously presented deep reinforcement learning framework to iteratively optimize a series of engine geometries over a range of increasingly strict NO x emissions regulations. We then examine the resulting injection schedules. We discuss the potential for using this deep reinforcement learning framework for fuel selection screening and for discovering unique injection strategies for different engine geometries and future emissions standards.

33 ADVANCED PROPULSION SYSTEMS↗

Modeling and optimization of solar thermoelectric generators for terrestrial applications

We introduce a model and an optimization methodology for terrestrial solar thermoelectric generators (STEGs). We describe, discuss, and justify the necessary constraints on the STEG geometry that make the STEG optimization independent of individual dimensions. A simplified model shows that the thermoelectric elements in STEGs can be scaled in size without affecting the overall performance of the device, even when the properties of the thermoelectric material and the solar absorber are temperature-dependent. Consequently, the amount of thermoelectric material can be minimized to be only a negligible fraction of the total system cost. As an example, a Bi 2 Te 3 -based STEG is optimized for rooftop power generation. Peak efficiency is predicted to be 5% at the standard spectrum AM1.5G, with the thermoelectric material cost below 0.05 $/W p . Integrating STEGs into solar hot water systems for cogeneration adds electricity at minimal extra cost. In such cogeneration systems the electric current can be adjusted throughout the day to favor either electricity or hot water production.

14 SOLAR ENERGY↗

SU-E-J-52: Dosimetric Benefit of Adaptive Re-Planning in Lung Cancer Stereotactic Body Radiotherapy (SBRT)

Purpose: To investigate the dosimetric benefit of adaptive re-planning for lung stereotactic body radiotherapy(SBRT). Methods: Five lung cancer patients with SBRT treatment were retrospectively investigated. Our in-house supercomputing online re-planning environment (SCORE) was used to realize the re-planning process. First a deformable image registration was carried out to transfer contours from treatment planning CT to each treatment CBCT. Then an automatic re-planning using original plan DVH guided fluence-map optimization is performed to get a new plan for the up-to-date patient geometry. We compared the re-optimized plan to the original plan projected on the up-to-date patient geometry in critical dosimetric parameters, such as PTV coverage, spinal cord maximum and volumetric constraint dose, esophagus maximum and volumetric constraint dose. Results: The average volume of PTV covered by prescription dose for all patients was improved by 7.56% after the adaptive re-planning. The volume of the spinal cord receiving 14.5Gy and 23Gy (V14.5, V23) decreased by 1.48% and 0.68%, respectively. For the esophagus, the volume receiving 19.5Gy (V19.5) reduced by 1.37%. Meanwhile, the maximum dose dropped off by 2.87% for spinal cord and 4.80% for esophagus. Conclusion: Our experimental results demonstrate that adaptive re-planning for lung SBRT has the potential to minimize the dosimetric effect of inter-fraction deformation and thus improve target coverage while reducing the risk of toxicity to nearby normal tissues.

60 APPLIED LIFE SCIENCES↗

Aerosol‐Jet‐Printable Covalent Organic Framework Colloidal Inks and Temperature‐Sensitive Nanocomposite Films

Abstract With molecularly well‐defined and tailorable 2D structures, covalent organic frameworks (COFs) have emerged as leading material candidates for chemical sensing, storage, separation, and catalysis. In these contexts, the ability to directly and deterministically print COFs into arbitrary geometries will enable rapid optimization and deployment. However, previous attempts to print COFs have been restricted by low spatial resolution and/or post‐deposition polymerization that limits the range of compatible COFs. Here, these limitations are overcome with a pre‐synthesized, solution‐processable colloidal ink that enables aerosol jet printing of COFs with micron‐scale resolution. The ink formulation utilizes the low‐volatility solvent benzonitrile, which is critical to obtaining homogeneous printed COF film morphologies. This ink formulation is also compatible with other colloidal nanomaterials, thus facilitating the integration of COFs into printable nanocomposite films. As a proof‐of‐concept, boronate‐ester COFs are integrated with carbon nanotubes (CNTs) to form printable COF‐CNT nanocomposite films, in which the CNTs enhance charge transport and temperature sensing performance, ultimately resulting in high‐sensitivity temperature sensors that show electrical conductivity variation by 4 orders of magnitude between room temperature and 300 °C. Overall, this work establishes a flexible platform for COF additive manufacturing that will accelerate the incorporation of COFs into technologically significant applications.

2D materials↗

Computational design of microarchitected porous electrodes for redox flow batteries

Porous electrodes are used as the core reactive component across electrochemical technologies. In flowing systems, controlling the fluid distribution, species transport, and reactive environment is critical to attaining high performance. However, conventional electrode materials like felts and papers provide few opportunities for precise engineering of the electrode and its microstructure. To address these limitations, architected electrodes composed of unit cells with spatially varying geometry determined via computational optimization are proposed. Resolved simulation is employed to develop a homogenized description of the constituent unit cells. These effective properties serve as inputs to a continuum model for the electrode when used in the negative half-cell of a vanadium redox flow battery. Porosity distributions minimizing power loss are then determined via computational design optimization to generate architected porosity electrodes. The architected electrodes are compared to bulk, uniform porosity electrodes and found to lead to increased power efficiency across operating flow rates and currents. The design methodology is further used to generate a scaled-up electrode with comparable power efficiency to the bench-scale systems. Finally, the variable porosity architecture and computational design methodology presented here thus offers a novel pathway for automatically generating spatially engineered electrode structures with improved power performance.

25 ENERGY STORAGE↗

A Comparative Ab Initio Study of the Primary Hydration and Proton Dissociation of Various Imide and Sulfonic Acid Ionomers

We compare the role of neighboring group substitutions on proton dissociation of hydrated acidic moieties suitable for proton exchange membranes through electronic structure calculations. Three pairs of ionomers containing similar electron withdrawing groups within the pair were chosen for the study: two fully fluorinated sulfonyl imides (CF3SO2NHSO2CF3 and CF3CF2SO2NHSO2CF3), two partially fluorinated sulfonyl imides (CH3SO2NHSO2CF3 and C6H5SO2NHSO2CF2CF3), and two aromatic sulfonic acid based material s (CH3C6H4SO3H and CH3 OC6 - H3OCH3C6H4SO3H). Fully optimized counterpoise (CP) corrected geometries were obtained for each ionomer fragment with the inclusion of water molecules at the B3LYP/6-311G** level of density functional theory. Spontaneous proton dissociation was observed upon addition of three water molecules in each system, and the transition to a solvent-separated ion pair occurred when four water molecules were introduced. No considerable quantitative or qualitative differences in proton dissociation, hydrogen bond networks formed, or water binding energies were found between systems containing similar electron withdrawing groups. Each of the sulfonyl imide ionomers exhibited qualitatively similar results regarding proton dissociation and separation. The fully fluorinated sulfonyl imides, however, showed a greater propensity to exist in dissociated and ion-pair separated states at low degrees of hydration than the partially fluorinated sulfonyl imides. This effect is due to the additional electron withdrawing groups providing charge stabilization as the dissociated proton migrates away from the imide anion.

30 DIRECT ENERGY CONVERSION↗

A Theoretical Study of the Interactions of In+ and In+3 with a Stone-Wales Defect Single-Walled Carbon Nanotubes.

Experimental techniques [1] have demonstrated the controllable, reversible and mass transport exchange of indium nanocrystals along surfaces of multi-walled carbon nanotubes (MWCNTs). In particular, at certain sites robust nucleation occurs suggesting preferred locations for controlled manipulation. We believe these site locations represent structural defects, like rehybridization, incomplete bonding and topological defects within the carbon network. Although minute, these defects can drastically modify the electrical, chemical and mechanical properties of CNTs. This study was devoted to understand the role of structural defects, specifically a Stone-Wales (SW) defect in the surface transport and interaction properties of the In{sup +1} and In{sup +3} for both the singlet and triplet state. The effects of CNT surface curvature on In+1 and In{sup +3} is also studied and compared to graphite. Geometries of complexes were optimized at the B3LYP level. The standard 6-31G(d) basis set was used for carbon and hydrogen atoms while an effective core potential (ECP) was used for indium. All calculations were performed using the Gaussian 03 suite of programs. The computed Mulliken charges and HOMOLUMO gap energies, interactions and interaction energy (corrected by the basis set superposition error) of the systems have been studied and will be discussed. Figure 1 represents the comparison of the molecular electrostatic potential maps for (a) In{sup +} and (b) In{sup +3} with a SW defect CNT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Efficient laser-driven proton acceleration from cylindrical and planar cryogenic hydrogen jets

We report on recent experimental results deploying a continuous cryogenic hydrogen jet as a debris-free, renewable laser-driven source of pure proton beams generated at the 150 TW ultrashort pulse laser Draco. Efficient proton acceleration reaching cut-off energies of up to 20 MeV with particle numbers exceeding 109 particles per MeV per steradian is demonstrated, showing for the first time that the acceleration performance is comparable to solid foil targets with thicknesses in the micrometer range. Two different target geometries are presented and their proton beam deliverance characterized: cylindrical (Ø 5 μm) and planar (20 μm × 2 μm). In both cases typical Target Normal Sheath Acceleration emission patterns with exponential proton energy spectra are detected. Significantly higher proton numbers in laser-forward direction are observed when deploying the planar jet as compared to the cylindrical jet case. As a result, this is confirmed by two-dimensional Particle-in-Cell (2D3V PIC) simulations, which demonstrate that the planar jet proves favorable as its geometry leads to more optimized acceleration conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The addition of methanol to Criegee intermediates

Bimolecular reactions involving stabilized Criegee intermediates (SCI) have been the target of many studies due to the role these molecules play in atmospheric chemistry. Recently, kinetic rates for the addition reaction of the simplest SCI (formaldehyde oxide) and its methylated analogue (acetone oxide) with methanol were reported both experimentally and theoretically. We re-examine the energy profile of these reactions by employing rigorous ab initio methods. Optimized CCSD(T)/ANO1 geometries are reported for the stationary points along the reaction path. Energies are obtained at the CCSD(T)/CBS level of theory. Contributions of full triple and quadruple excitations are computed to assess the convergence of this method. Rate constants are obtained using conventional canonical transition state theory under the rigid rotor harmonic oscillator approximation and with the inclusion of a one-dimensional hindered rotor treatment. These corrections for internal rotations have a significant impact on computed kinetic rate constants. With this approach, we compute rate constants for the addition of methanol to formaldehyde oxide (H 2 COO) and acetone oxide [(CH 3 ) 2 COO] at 298.15 K as (1.2 ± 0.8) × 10 -13 and (2.8 ± 1.3) × 10 -15 cm 3 s -1 , respectively. Additionally, we investigate the temperature dependence of the rate constant, concluding that the transition state barrier height and tunneling contributions shape the qualitative behaviour of these reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Coil Array Design Inspired on the Kepler's Lenten Pretzel

The RF coil arrays are an important part in Magnetic Resonance Imaging, since they are the main device for transmission and reception of the magnetic resonance signal. An RF coil array with a new configuration based on the Kepler's Lenten pretzel for the geocentric path of Mars is proposed in this work. The evenly distributed trajectories may serve as the basic configuration to form a coil array to adequately cover a region of interest for magnetic resonance experiments. The main goal is to investigate the electromagnetic properties of this coil array geometry to obtain an optimal design for its further construction. Hence, the electromagnetic properties of the coil array were numerical simulated using the finite element method and the quasi-static approach. Resulting simulations showed that there is an important concentration of magnetic field lines at the centre of the coil array. This is an advantage over other coil arrays where the magnetic field usually decreased at their geometrical centre. Both the electric and magnetic fields had also a very good uniformity. These characteristics made this coil design a good candidate for applications where the use of multi-coil technology is mandatory.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Turbulence-driven zonal flows in helical systems with radial electric fields

Collisionless long-time responses of the zonal-flow potential to the initial condition and turbulence source in helical systems having radial electric fields are derived theoretically. All classes of particles in passing, toroidally trapped, and helical-ripple-trapped states are considered. The transitions between the toroidally trapped and helical-ripple-trapped states are taken into account while solving the gyrokinetic equation analytically by taking its average along the particle orbits. When the radial displacements of helical-ripple-trapped particles are reduced either by neoclassical optimization of the helical geometry lowering the radial drift or by strengthening the radial electric field E{sub r} to boost the poloidal rotation, enhanced zonal-flow responses are obtained. Under the identical conditions on the magnitude of E{sub r} and the magnetic geometry, using ions with a heavier mass gives rise to a higher zonal-flow response, and therefore the turbulent transport is expected to show a more favorable ion-mass dependence than the conventional gyro-Bohm scaling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗