SEARCH · Search NASA

Results for “interactive data visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

All sources NASA NTRS DOE OSTI

NASA NTRS1987

An LDA investigation of three-dimensional normal shock-boundary layer interactions in a corner

Nonintrusive, three-dimensional, measurements have been made of a normal shock wave-turbulent boundary layer interaction. The measurements were made in the corner of the test section of a continuous supersonic wind tunnel in which a normal shock wave had been stabilized. LDA, surface pressure measurement and flow visualization techniques were employed for two freestream Mach number test cases: 1.6 and 1.3. The former contained separated flow regions and a system of shock waves. The latter was found to be far less complicated. The reported results are believed to accurately define the flow physics of each case and may be used as benchmark data to verify three-dimensional computer codes.

Chriss, R. M.↗

NASA NTRS1990

Experimental investigation of a single flush-mounted hypermixing nozzle

The results of an experimental wind tunnel investigation of a circular supersonic jet (m sub j = 3.47) injected at a 10 degree angle into a supersonic freestream. The jet penetrates a boundary layer, which has a thickness approximately the same as the jet nozzle exit diameter. Measurements were made for nominal freestream Mach numbers of 1.6, 2.0, 2.5, and 3.0. Three jet total pressures were run at each freestream Mach number, resulting in twelve separate operating conditions. Mean data accumulated by means of static and total pressure probe instrumentation are presented at two axial stations: seven jet nozzle diameters upstream and 15 jet nozzle diameters downstream from where the centerline of the nozzle intersects the wind tunnel wall. For one condition at each freestream Mach number, the jet air was seeded with a hydrocarbon trace gas and the flow was sampled at the downstream measurement plane to quantify the mean mixing of the two streams. Surface oil flow visualization was also used to investigate the flow interaction. All results are for air-to-air mixing. The measurements indicate the presence of two pairs contra-rotating vortices. One pair follows the jet trajectory and tends to split the jet into two streams. A smaller pair, rotating in an opposite sense, develops in the near wall region. Reported results include Mach number and volume fraction distributions in the cross plane, as well as jet penetration and mixing efficiency.

Davis, David O.↗

NASA NTRS1993

The Effects of Gravity on Wrinkled Laminar Flames

The effects of gravity are significant to the dynamics of idealized unconfined open premixed flames. Moderate to low turbulence Reynolds number flames, i.e., wrinkled laminar flames, of various unconfined geometries have been used extensively for investigating fundamental processes of turbulent flame propagation and to validate theoretical models. Without the wall constraints, the flames are free to expand and interact with surrounding ambient air. The flow field in which the flame exists is determined by a coupling of burner geometry, flame orientation and the gravity field. These complex interactions raise serious questions regarding the validity of comparing the experimental data of open flames with current theoretical and numerical models that do not include the effects of gravity nor effects of the larger aerodynamic flowfield. Therefore, studies of wrinkled laminar flame in microgravity are needed for a better understanding of the role of gravity on flame characteristics such as the orientation, mean aerodynamics stretch, flame wrinkle size and burning rate. Our approach to characterize and quantify turbulent flame structures under microgravity is to exploit qualitative and quantitative flow visualization techniques coupled with video recording and computer controlled image analysis technologies. The experiments will be carried out in the 2.2 second drop tower at the NASA Lewis Research Center. The longest time scales of typical wrinkled laminar flames in the geometries considered here are in the order of 10 msec. Hence, the duration of the drop is sufficient to obtain the amount of statistical data necessary for characterize turbulent flame structures.

Kostiuk, Larry W.↗

NASA NTRS2018

HYPERS Software Development

Providing software support for HYPERS and creating internal tools. NASA has a long and decorated history of spaceflight innovation and achievements. The next great endeavor is NASA’s Journey to Mars, which will be achieved with the Space Launch System (SLS) and Orion capsule. Developing and testing these systems is no easy feat. Commercial-off-the-shelf (COTS) tools do not always provide enough functionality for engineers to do their job efficiently, making internal custom-made tools is necessary to meet the expected launch date. The purpose of this internship was to provide software support to the Storable Propellants and Hydraulic Systems Branch, specifically the Hypergolics Software (HYPERS) team. This included developing tools to parse unique measurements from the vehicle into the format specified by the HYPERS team. Displays were also created per requirements. Another major component of this internship was to create an intuitive interactive offline graphing application. The current tool for plotting vehicle data does not have all the functionality and features that HYPERS would like. By inputting a vehicle data file, the application plots the data based on the time range and components the user would like to view. After the graph is generated, the user is able to zoom in, pan horizontally, add comments, hover over data points, and take a snapshot of the current state of the graph. These additional features will help engineers quickly investigate the relationship between vehicle components through data visualization.

Internal Tools↗

NASA NTRS2010

Effects of Hydrocarbon-Based Grease on Rapid Prototype Material Used for Grease Retention Shrouds

Effects of hydrocarbon-based greases on specific rapid prototype (RP) materials used to fabricate grease retention shrouds (GRS) were explored in this study. Grease retention shrouds are being considered as a way to maintain adequate grease lubrication at the gear mesh in a prototype research transmission system. Due to their design and manufacturing flexibility, rapid prototype materials were chosen for the grease retention shrouds. In order to gain a better understanding of the short and long term effects grease pose on RP materials, research was conducted on the interaction of hydrocarbon-based grease with RP materials. The materials used in this study were durable polyamide (nylon), acrylonitrile butadiene styrene (ABS), and WaterClear 10120. Testing was conducted using Mobilgrease 28 and Syn-Tech 3913G grease (gear coupling grease). These greases were selected due to their regular use with mechanical components. To investigate the effect that grease has on RP materials, the following methods were used to obtain qualitative and quantitative data: Fourier transform infrared spectroscopy (FT-IR), interference profilometer measurements, digital camera imaging, physical shape measurement, and visual observations. To record the changes in the RP materials due to contact with the grease, data was taken before and after the grease application. Results showed that the WaterClear 10120 RP material provided the best resistance to grease penetration as compared to nylon and ABS RP materials. The manufacturing process, and thus resulting surface conditions of the RP material, played a key role in the grease penetration properties and resilience of these materials.

Zakrajsek, Andrew J.↗

NASA NTRS2016

Sweeping Jet Optimization Studies

Progress on experimental efforts to optimize sweeping jet actuators for active flow control (AFC) applications with large adverse pressure gradients is reported. Three sweeping jet actuator configurations, with the same orifice size but di↵erent internal geometries, were installed on the flap shoulder of an unswept, NACA 0015 semi-span wing to investigate how the output produced by a sweeping jet interacts with the separated flow and the mechanisms by which the flow separation is controlled. For this experiment, the flow separation was generated by deflecting the wing's 30% chord trailing edge flap to produce an adverse pressure gradient. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the three actuator configurations. The actuator with the largest jet deflection angle, at the pressure ratios investigated, was the most efficient at controlling flow separation on the flap of the model. Oil flow visualization studies revealed that the flow field controlled by the sweeping jets was more three-dimensional than expected. The results presented also show that the actuator spacing was appropriate for the pressure ratios examined.

Melton, LaTunia Pack↗

NASA NTRS2011

Using Multi-Scale Modeling Systems and Satellite Data to Study the Precipitation Processes

In recent years, exponentially increasing computer power has extended Cloud Resolving Model (CRM) integrations from hours to months, the number of computational grid points from less than a thousand to close to ten million. Three-dimensional models are now more prevalent. Much attention is devoted to precipitating cloud systems where the crucial 1-km scales are resolved in horizontal domains as large as 10,000 km in two-dimensions, and 1,000 x 1,000 km2 in three-dimensions. Cloud resolving models now provide statistical information useful for developing more realistic physically based parameterizations for climate models and numerical weather prediction models. It is also expected that NWP and mesoscale model can be run in grid size similar to cloud resolving model through nesting technique. Recently, a multi-scale modeling system with unified physics was developed at NASA Goddard. It consists of (l) a cloud-resolving model (Goddard Cumulus Ensemble model, GCE model), (2) a regional scale model (a NASA unified weather research and forecast, WRF), (3) a coupled CRM and global model (Goddard Multi-scale Modeling Framework, MMF), and (4) a land modeling system. The same microphysical processes, long and short wave radiative transfer and land processes and the explicit cloud-radiation, and cloud-land surface interactive processes are applied in this multi-scale modeling system. This modeling system has been coupled with a multi-satellite simulator to use NASA high-resolution satellite data to identify the strengths and weaknesses of cloud and precipitation processes simulated by the model. In this talk, the recent developments and applications of the multi-scale modeling system will be presented. In particular, the results from using multi-scale modeling system to study the precipitating systems and hurricanes/typhoons will be presented. The high-resolution spatial and temporal visualization will be utilized to show the evolution of precipitation processes. Also how to use of the multi-satellite simulator tqimproy~ precipitation processes will be discussed.

Tao, Wei-Kuo↗

NASA NTRS2011

Standardization of a Volumetric Displacement Measurement for Two-Body Abrasion Scratch Test Data Analysis

A limitation has been identified in the existing test standards used for making controlled, two-body abrasion scratch measurements based solely on the width of the resultant score on the surface of the material. A new, more robust method is proposed for analyzing a surface scratch that takes into account the full three-dimensional profile of the displaced material. To accomplish this, a set of four volume- displacement metrics was systematically defined by normalizing the overall surface profile to denote statistically the area of relevance, termed the Zone of Interaction. From this baseline, depth of the trough and height of the plowed material are factored into the overall deformation assessment. Proof-of-concept data were collected and analyzed to demonstrate the performance of this proposed methodology. This technique takes advantage of advanced imaging capabilities that allow resolution of the scratched surface to be quantified in greater detail than was previously achievable. When reviewing existing data analysis techniques for conducting two-body abrasive scratch tests, it was found that the ASTM International Standard G 171 specified a generic metric based only on visually determined scratch width as a way to compare abraded materials. A limitation to this method was identified in that the scratch width is based on optical surface measurements, manually defined by approximating the boundaries, but does not consider the three-dimensional volume of material that was displaced. With large, potentially irregular deformations occurring on softer materials, it becomes unclear where to systematically determine the scratch width. Specifically, surface scratches on different samples may look the same from a top view, resulting in an identical scratch width measurement, but may vary in actual penetration depth and/or plowing deformation. Therefore, two different scratch profiles would be measured as having identical abrasion properties, although they differ significantly.

Street, K. W. Jr.↗

NASA NTRS1993

Unsteady, three-dimensional, Navier-Stokes simulations of multistage turbomachinery flows

Hub corner stall regions, endwall boundary layers, tip leakage flows and airfoil wakes combine to form the 3D flowfields found in axial turbomachines. Turbomachinery flow fields are also inherently unsteady because of the relative motion between rotor and stator airfoils. This relative motion causes complex time-varying aerodynamic interactions to occur between the different aerodynamic structures and the rotor and stator airfoils. It is necessary to understand the 3D unsteady aerodynamics associated with these interactions in order to design turbomachines that are both lightweight and compact as well as reliable and efficient. The current study uses a time-accurate 3D thin-layer Navier-Stokes zonal approach to investigate the unsteady aerodynamics of multistage turbines and compressors. Relative motion between rotor and stator airfoils is accounted for by the use of systems of patched and overlaid grids. Time-averaged surface pressures, surface flow visualizations, and time-averaged flow field contours have been computed for a 1 1/2-stage turbine and are in good agreement with experimental data. This favorable comparison represents an initial validation of the current method for unsteady computations of multistage turbomachinery flows.

Gundy-Burlet, Karen L.↗

NASA NTRS1998

SSBRP Communication & Data System Development using the Unified Modeling Language (UML)

The Unified Modeling Language (UML) is the standard method for specifying, visualizing, and documenting the artifacts of an object-oriented system under development. UML is the unification of the object-oriented methods developed by Grady Booch and James Rumbaugh, and of the Use Case Model developed by Ivar Jacobson. This paper discusses the application of UML by the Communications and Data Systems (CDS) team to model the ground control and command of the Space Station Biological Research Project (SSBRP) User Operations Facility (UOF). UML is used to define the context of the system, the logical static structure, the life history of objects, and the interactions among objects.

Windrem, May↗

NASA NTRS1994

Development of a multicomponent force and moment balance for water tunnel applications, volume 1

The principal objective of this research effort was to develop a multicomponent strain gauge balance to measure forces and moments on models tested in flow visualization water tunnels. An internal balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The five-components to applied loads, low interactions between the sections and no hysteresis. Static experiments (which are discussed in this Volume) were conducted in the Eidetics water tunnel with delta wings and a model of the F/A-18. Experiments with the F/A-18 model included a thorough baseline study and investigations of the effect of control surface deflections and of several Forebody Vortex Control (FVC) techniques. Results were compared to wind tunnel data and, in general, the agreement is very satisfactory. The results of the static tests provide confidence that loads can be measured accurately in the water tunnel with a relatively simple multicomponent internal balance. Dynamic experiments were also performed using the balance, and the results are discussed in detail in Volume 2 of this report.

Suarez, Carlos J.↗

NASA NTRS2003

Modeling and Visualizing Uncertainty in Continuous Variables Predicted using Remotely Sensed Data

The use of remotely sensed images to map continuous biophysical variables, such as those related to terrestrial vegetation amount, sea surface temperature, and many other targets of NASA s Earth Observing System (EOS), includes variable, parametric, positional, spatial support and structural sources of uncertainty. A complete description of uncertainty will lead to a probability distribution at each location, allowing the exploration of the spatial dimension of uncertainty, that is, where the field is not well quantified. To achieve this purpose, convenient visualization tools are required. We have produced such a tool, called PDFVis, that facilitates the display of probability density functions (pdfs) on a per-grid-cell basis. The density estimate from Monte-Carlo generated realizations is interactively displayed as well as parametric and non-parametric summaries of the pdf field (such as mean, median, quartiles, standard deviation, number of modes, and locations of modes). Shaded surface renderings of pdfs along a transect can also be projected onto a plane. This tool will become more useful as richer descriptions of spatial uncertainty become available.

Dungan, Jennifer L.↗

NASA NTRS1979

VORTAB - A data-tablet method of developing input data for the VORLAX program

A method of developing an input data file for use in the aerodynamic analysis of a complete airplane with the VORLAX computer program is described. The hardware consists of an interactive graphics terminal equipped with a graphics tablet. Software includes graphics routines from the Tektronix PLOT 10 package as well as the VORTAB program described. The user determines the size and location of each of the major panels for the aircraft before using the program. Data is entered both from the terminal keyboard and the graphics tablet. The size of the resulting data file is dependent on the complexity of the model and can vary from ten to several hundred card images. After the data are entered, two programs READB and PLOTB, are executed which plot the configuration allowing visual inspection of the model.

Denn, F. M.↗

NASA NTRS1990

Interaction of feel system and flight control system dynamics on lateral flying qualities

An experimental investigation of the influence of lateral feel system characteristics on fighter aircraft roll flying qualities was conducted using the variable stability USAF NT-33. Forty-two evaluation flights were flown by three engineering test pilots. The investigation utilized the power approach, visual landing task and up-and-away tasks including formation, gun tracking, and computer-generated compensatory attitude tracking tasks displayed on the Head-Up Display. Experimental variations included the feel system frequency, force-deflection gradient, control system command type (force or position input command), aircraft roll mode time constant, control system prefilter frequency, and control system time delay. The primary data were task performance records and evaluation pilot comments and ratings using the Cooper-Harper scale. The data highlight the unique and powerful effect of the feel system of flying qualities. The data show that the feel system is not 'equivalent' in flying qualities influence to analogous control system elements. A lower limit of allowable feel system frequency appears warranted to ensure good lateral flying qualities. Flying qualities criteria should most properly treat the feel system dynamic influence separately from the control system, since the input and output of this dynamic element is apparent to the pilot and thus, does not produce a 'hidden' effect.

Bailey, R. E.↗

NASA NTRS1996

The barberplaid illusion: plaid motion is biased by elongated apertures

The perceived direction of motion of plaids windowed by elongated spatial Gaussians is biased toward the window's long axis. The bias increases as the relative angle between the plaid motion and the long axis of the window increases, peaks at a relative angle of approximately 45 deg, and then decreases. The bias increases as the window is made narrower (at fixed height) and decreases as the component spatial frequency increases (at fixed aperture size). We examine several models of human motion processing (cross-correlation, motion-energy, intersection-of-constraints, and vector-sum), and show that none of these standard models can predict our data. We conclude that spatial integration of motion signals plays a crucial role in plaid motion perception and that current models must be explicitly expanded to include such spatial interactions.

NASA Center ARC↗

NASA NTRS1992

Total Dose Effects (TDE) of heavy ionizing radiation in fungus spores and plant seeds: Preliminary investigations

The opportunity to compare cosmic radiation effects caused during long and short duration exposure flights in biological objects are limited until now, and data obtained so far are very rare and insufficient. Because of the very long exposure of the experiment during the Long Duration Exposure Facility (LDEF) mission (approximately 2000 days) structural changes of the hardware material can be expected which will influence its biocompatibility and, thus, will interact with the radiobiological effects. The aim of the experiment flown on LDEF was a detailed investigation of biological effects caused by cosmic radiation especially of particles of high atomic number Z and high energy. The flight hardware consisted of standard BIOSTACK containers; in these containers a special sandwich construction consisted of visual plastic detectors with seed rsp. spore layers interlocked.

Kranz, A. R.↗

NASA NTRS1994

An Overview of Unsteady Three-Dimensional Navier-Stokes Simulations of Multistage Turbomachinery Flows

Fluid dynamics of turbomachines are complicated by inherently three dimensional structures such as endwall boundary layers, hub corner separation bubbles and tip-leakage flows. In addition, the relative motion between rotors and stators causes unsteady aerodynamic interactions to occur between blade rows. It is necessary to understand the aerodynamics associated with these interactions in order to design turbomachines that are both light and compact as well as reliable and efficient. An unsteady, three-dimensional, thin-layer, Navier-Stokes zonal algorithm is used to investigate the unsteady aerodynamics of multi-stage turbines and compressors. Relative motion between rotors and stators is made possible by the use of systems of patched and overlaid grids. Time-averaged pressures and pressure envelopes have been computed for several two- and three-dimensional single- and multi-stage configurations. Flow visualizations and computed results are in good agreement with experimental data.

Gundy-Burlet, Karen L.↗

NASA NTRS2012

JPL Genesis and Rapid Intensification Processes (GRIP) Portal

Satellite observations can play a very important role in airborne field campaigns, since they provide a comprehensive description of the environment that is essential for the experiment design, flight planning, and post-experiment scientific data analysis. In the past, it has been difficult to fully utilize data from multiple NASA satellites due to the large data volume, the complexity of accessing NASA s data in near-real-time (NRT), as well as the lack of software tools to interact with multi-sensor information. The JPL GRIP Portal is a Web portal that serves a comprehensive set of NRT observation data sets from NASA and NOAA satellites describing the atmospheric and oceanic environments related to the genesis and intensification of the tropical storms in the North Atlantic Ocean. Together with the model forecast data from four major global atmospheric models, this portal provides a useful tool for the scientists and forecasters in planning and monitoring the NASA GRIP field campaign during the 2010 Atlantic Ocean hurricane season. This portal uses the Google Earth plug-in to visualize various types of data sets, such as 2D maps, wind vectors, streamlines, 3D data sets presented at series of vertical cross-sections or pointwise vertical profiles, and hurricane best tracks and forecast tracks. Additionally, it allows users to overlap multiple data sets, change the opacity of each image layer, generate animations on the fly with selected data sets, and compare the observation data with the model forecast using two independent calendars. The portal also provides the capability to identify the geographic location of any point of interest. In addition to supporting the airborne mission planning, the NRT data and portal will serve as a very rich source of information during the post-field campaign analysis stage of the airborne experiment. By including a diverse set of satellite observations and model forecasts, it provides a good spatial and temporal context for the high-resolution, but limited in space and time, airborne observations.

Knosp, Brian W.↗