Search NASA⌕ Search

SEARCH · Search NASA

Results for “mobility models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 901 records · Page 50

Comparison of observed rheological properties of hard wheat flour dough with predictions of the Giesekus-Leonov, White-Metzner and Phan-Thien Tanner models

The measured rheological behavior of hard wheat flour dough was predicted using three nonlinear differential viscoelastic models. The Phan-Thien Tanner model gave good zero shear viscosity prediction, but overpredicted the shear viscosity at higher shear rates and the transient and extensional properties. The Giesekus-Leonov model gave similar predictions to the Phan-Thien Tanner model, but the extensional viscosity prediction showed extension thickening. Using high values of the mobility factor, extension thinning behavior was observed but the predictions were not satisfactory. The White-Metzner model gave good predictions of the steady shear viscosity and the first normal stress coefficient but it was unable to predict the uniaxial extensional viscosity as it exhibited asymptotic behavior in the tested extensional rates. It also predicted the transient shear properties with moderate accuracy in the transient phase, but very well at higher times, compared to the Phan-Thien Tanner model and the Giesekus-Leonov model. None of the models predicted all observed data consistently well. Overall the White-Metzner model appeared to make the best predictions of all the observed data.

Non-NASA Center↗

A model for the spectral dependence of optically induced absorption in amorphous silicon

A model based on transitions from localized band tail states to states above the mobility edge is used to explain the broad band induced absorptions observed in recent pump-probe experiments. The model gives the observed decrease of absorption with frequency at subband gap photo energies and high carrier densities (of about 10 to the 20th/cu cm). At lower carrier densities, the absorption has a maximun which is sensitive to the spatial extent of the band tail states.

Lawandy, N. M.↗

Theory for Glassy Behavior of Supercooled Liquid Mixtures

Here, we introduce a model for glassy dynamics in supercooled liquid mixtures. Given the relaxation behavior of individual supercooled liquids, the model predicts the relaxation times of their mixtures as temperature is decreased. The model is based on dynamical facilitation theory for glassy dynamics, which provides a physical basis for relaxation and vitrification of a supercooled liquid. This is in contrast to empirical linear interpolations such as the Gordon-Taylor equation typically used to predict glass transition temperatures of liquid mixtures. To understand the behavior of supercooled liquid mixtures we consider a multicomponent variant of the kinetically constrained East model in which components have a different energy scale and can also diffuse when locally mobile regions, i.e., excitations, are present. Using a variational approach we confirm an effective single component model with a single effective energy scale that best approximates a mixture. When scaled by this single effective energy, we show that experimental relaxation times of many liquid mixtures all collapse onto the "parabolic law" predicted by dynamical facilitation theory. The model can be used to predict transport properties and glass transition temperatures of mixtures of glassy materials, with implications in atmospheric chemistry, biology, and pharmaceuticals.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Large N Fractons

We consider theories of N -component fields with exotic spacetime symmetries, including a conserved dipole moment. Microscopic charges are immobile by symmetry, and so resemble fractons. Using collective fields we solve these models to leading order in large N . The large N solution reveals that these models are strongly correlated, and that interactions dress the microscopic charges so that they become mobile, long-lived quasiparticles. Dipole symmetry is spontaneously broken throughout the phase diagram of these models, leading to a low-energy Goldstone description. Published by the American Physical Society 2024

Physics↗

DC Modeling of 4H-SiC JFET Gate Length Reduction at 500°C

The development of robust, high-performance integrated circuits (ICs) will enable numerous potential NASA missions of current interest, including long-duration robotic missions exploring the 460 °C surface of Venus. Currently, NASA is looking towards SiC-based devices to provide such a solution. However, the current NASA silicon carbide (SiC) JFET device with a channel length of 6μm (for recently fabricated Gen. 11 ICs) limits on mission relevant circuit capabilities [1]. In this study, we combined experiments with simulations to explore two straightforward fabrication strategies to reduce the SiC JFET channel length while maintaining turn-off behavior (Fig. 1a) needed to realize 500 °C circuit operation. The first fabrication strategy uses a shallow self-align nitrogen implant (Figure 1b) along the device's top surface but not below the gate combined with a high-dose phosphorous implant directly below the source and drain contacts. For the second fabrication strategy (Figure 1c), the high-dose phosphorous implants extended from below the contacts all the way up to the gate edges. Simulations guided gate length reductions without significant degradation in the turn-off performance. In total 12 SiC JFET variants implementing using the different fabrication strategies, gate lengths, and n-channel epilayer thickness were implemented in our simulation framework implemented in COMSOL. Since the COMSOL database does not have the material properties for 4H-SiC, these parameters were taken from the literature and implemented in COMSOL. The empirical models [2] for incomplete ionization, Auger recombination, low field mobility, and Shockley-Read-Hall recombination were implemented to account for material-specific device behavior.

4H-SiC JFET↗

Mobility enhancement in crystalline In-Ga-Zn-oxide with In-rich compositions

The electron mobility of In-Ga-Zn-oxide (IGZO) is known to be enhanced by higher In content. We theoretically investigated the mobility-enhancement mechanism by proposing an In-Ga-Zn-disorder scattering model for an In-rich crystalline IGZO (In{sub 1+x}Ga{sub 1−x}O{sub 3}(ZnO){sub m} (0 < x < 1, m > 0)) thin film. The obtained theoretical mobility was found to be in agreement with experimental Hall mobility for a crystalline In{sub 1.5}Ga{sub 0.5}O{sub 3}(ZnO) (or In{sub 3}GaZn{sub 2}O{sub 8}) thin film. The mechanism specific to In-rich crystalline IGZO thin films is based on three types of Coulomb scattering potentials that originate from effective valence differences. In this study, the In-Ga-Zn-disorder scattering model indicates that the effective valence of the In{sup 3+} ions in In-rich crystalline IGZO thin films significantly affects their electron mobility.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Assessment of long-term spatio-temporal radiofrequency electromagnetic field exposure

Highlights: • A year's worth of RF-EMF data is collected in an urban sensor network is analysed. • A full spatio-temporal model of the RF-EMF exposure in the study area is built. • Short-term variations of the RF-EMF exposure are collected in temporal profiles. • Models using data collected at different instants are improved by adjusting for time. As both the environment and telecommunications networks are inherently dynamic, our exposure to environmental radiofrequency (RF) electromagnetic fields (EMF) at an arbitrary location is not at all constant in time. In this study, more than a year's worth of measurement data collected in a fixed low-cost exposimeter network distributed over an urban environment was analysed and used to build, for the first time, a full spatio-temporal surrogate model of outdoor exposure to downlink Global System for Mobile Communications (GSM) and Universal Mobile Telecommunications System (UMTS) signals. Though no global trend was discovered over the measuring period, the difference in measured exposure between two instances could reach up to 42 dB (a factor 12,000 in power density). Furthermore, it was found that, taking into account the hour and day of the measurement, the accuracy of the surrogate model in the area under study was improved by up to 50% compared to models that neglect the daily temporal variability of the RF signals. However, further study is required to assess the extent to which the results obtained in the considered environment can be extrapolated to other geographic locations.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗

NASA Advanced Air Mobility (AAM)

This presentation will provide a UTM update, AAM overview (including details on the AAM Ecosystem Working Groups), and Regional Modeling and Simulations tool description.

Advance Air Mobility↗

Mathematical models for cochannel interference in FH/MFSK multiple-access systems

FH/MFSK has been proposed for a multiuser spread spectrum digital communication system to combat both self-jamming and intentional jamming. An independence assumption at the energy detector outputs is used to evaluate such a system for a digitized voice mobile radio system (Yue, 1981). This paper presents a correlated model and compares its performance to an independence model under the symbol error probability criterion. A Gaussian process model is also developed for comparison. It is found that the conventional Gaussian approximation is inadequate in predicting the number of users that can be accommodated by an FH/MFSK system using the conventional receiver. Furthermore, for the cases evaluated, the independence model provides an excellent approximation to the correlated model. Additionally, a conditional Chernoff bound is presented for the more general case of frequency-hopping systems with multiple hops per symbol.

Yan, T.-Y.↗

Cryogenic-Refined MOSFET Modeling for Oscillator, Frequency Divider, and Amplifier Designs Below 4 K

Capturing device characteristic changes at cryogenic temperatures is crucial for cryo-CMOS circuit designs. In this work, we present an isothermal cryogenic-refined modeling approach for CMOS transistors that is simple, low overhead, and easy to implement while offering the required accuracy for predicting circuit performance at the designated temperatures. Guided by die-level measurement data and circuit design principles, the model introduces corrections to only five critical parameters: threshold voltage, carrier mobility, elevated low-frequency flicker noise, dominant high-frequency shot noise, and subthreshold swing (SS). These refinements are implemented around the foundry-provided SPICE model, which is typically validated only down to about 200 K. With these adjustments, the proposed cryogenic-refined model achieves less than 5% error in both large-signal metrics (I–V characteristics) and small-signal parameters (e.g., transconductance) when compared with device measurements at deep-cryogenic temperatures. The methodology is validated in two advanced technologies: TSMC 40-nm CMOS and GlobalFoundries (GF) 45-nm RF-SOI. We further demonstrate its applicability in three representative RF circuits: a 30-GHz LC oscillator, a high-speed current-mode-logic (CML) frequency divider (FD), and a subthreshold Gb/s amplifier, all showing close agreement between simulated predictions and measurements performed at 4 and 2.5 K. Finally, we believe that the proposed approach is implementation-friendly and can significantly accelerate the development of cryo-CMOS integrated circuits.

circuit modeling↗

GPS Moving Vehicle Experiment

The Naval Research Laboratory (NRL) in the development of timing systems for remote locations, had a technical requirement for a Y code (SA/AS) Global Positioning System (GPS) precise time transfer receiver (TTR) which could be used both in a stationary mode or mobile mode. A contract was awarded to the Stanford Telecommunication Corporation (STEL) to build such a device. The Eastern Range (ER) als had a requirement for such a receiver and entered into the contract with NRL for the procurement of additional receivers. The Moving Vehicle Experiment (MVE) described in this paper is the first in situ test of the STEL Model 5401C Time Transfer System in both stationary and mobile operations. The primary objective of the MVE was to test the timing accuracy of the newly developed GPS TTR aboard a moving vessel. To accomplish this objective, a joint experiment was performed with personnel from NRL and the er at the Atlantic Undersea Test and Evaluation Center (AUTEC) test range at Andros Island. Results and discussion of the test are presented in this paper.

Oaks, O. J.↗

Solids Mobilization and Suspension by Dual Opposed Mixing Pumps

Experiments were performed to support understanding mixing of radioactive waste stored in Tank 241-SY-101 at the Hanford Site in Washington State. These experiments were conducted at 1/12 scale and modeled the tank and proposed mixing pump. The tests investigated solids mobilization and suspension for jets rotated in fixed increments about the tank centerline. Flow visualization tests showed that the supernatant layer was generally too cloudy for effective visualization. Observations of the settled solids interface during a start-up transient showed that the mixing action was always confined within the slurry layer. A 4.57-m/s (15-ft/s) jet velocity was not capable of clearing settled sludge off the tank floor all the way to the tank wall and produced a stratified flow field at steady state; 7.62-m/s (25-ft/s) and higher jet velocities always circulated solids to the tank surface. During the operating parameter tests with jets rotated at fixed increments, the slurry interface rose more slowly than for the fixed location jets. Solids suspension was more effective for the rotated jets than for the fixed location jets. Percent solids suspended with a 7.62-m/s (25-ft/s) jet was 66 to 72% in the high viscosity simulant and 59 to 67% in the low viscosity simulant. Percent solids suspended with a 15.2 m/s (50-ft/s) jet was 74 to 81% in the low viscosity simulant. A 7.62 m/s (25-ft/s) jet velocity was adequate to clear settled solids from the tank floor to the tank wall for both the low and high viscosity simulant.

concentration profile↗

Machine learning reveals factors that control ion mobility in anti-perovskite solid electrolytes

Solid-state batteries are projected to exhibit improved energy densities and safety compared to liquid-electrolyte-based systems. Consequently, the development of solid electrolytes that can conduct cations at rates comparable to that of liquid electrolytes is an active area of research. To facilitate this search it is desirable to understand the chemical and structural features that control ion transport through a crystalline lattice. Here, machine learning (ML) is used to identify features that influence ion mobility in solids, quantify the relative importance of those features, and demonstrate how the variation of individual features alters ion mobility. Adopting the anti-perovskite lattice as a model system, ML algorithms were trained to predict migration barriers from a data set containing hundreds of barriers calculated using density functional theory. In this study, more than 10 6 feature sets of non-redundant descriptors were evaluated for their ability to predict migration barriers. The present analysis correctly reiterates the importance of several features that are known to influence mobility – for example, anion polarizability – but also identifies others whose importance is not widely recognized. Lattice properties such as hopping distance and channel width exhibit the greatest influence on cation mobility. Individual conditional expectation analyses performed on these features shows that barriers decrease as hopping distance decreases and as channel width increases. The defect formation energy – which is commonly associated with the concentration of defects, but not with their mobility – is identified as an important feature for interstitial migration. In sum, this analysis aids in the design of optimal solid electrolytes by simplifying the multi-dimensional design space to a sub-set of properties that are the most important.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Theory and measurement of plasmonic terahertz detector response to large signals

Electron gas in the conduction channel of a Field Effect Transistor (FET) can support collective plasma oscillations tunable by the gate voltage. In the Dyakonov-Shur terahertz (THz) detector, nonlinearities in the plasma wave propagation in the gated channel of a FET lead to a constant source-to-drain voltage providing the detector output. We present the detector theory in the frame of the hydrodynamic model using the electron plasma Navier-Stokes and thermal transport equations, thus fully accounting for the hydrodynamic non-linearity, the viscosity, and pressure gradients in the detector response. Both resonant and broadband operations of the high electron mobility transistor (HEMT) based plasmonic detectors are described by this model. The relation between the electron channel density and gate voltage was modeled by the unified charge control model applicable both above and below the threshold voltage. The theoretical results are compared with the response measured in the short channel InGaAs HEMT and the analytical approximation. The THz source was operating at 1.63 THz, and the response was measured at varying signal intensities. The response of the detector operated in the open drain mode was measured above and below the threshold, and the theoretical and experimental results are shown to be in good agreement.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Sample distribution in peak mode isotachophoresis

We present an analytical study of peak mode isotachophoresis (ITP), and provide closed form solutions for sample distribution and electric field, as well as for leading-, trailing-, and counter-ion concentration profiles. Importantly, the solution we present is valid not only for the case of fully ionized species, but also for systems of weak electrolytes which better represent real buffer systems and for multivalent analytes such as proteins and DNA. The model reveals two major scales which govern the electric field and buffer distributions, and an additional length scale governing analyte distribution. Using well-controlled experiments, and numerical simulations, we verify and validate the model and highlight its key merits as well as its limitations. We demonstrate the use of the model for determining the peak concentration of focused sample based on known buffer and analyte properties, and show it differs significantly from commonly used approximations based on the interface width alone. We further apply our model for studying reactions between multiple species having different effective mobilities yet co-focused at a single ITP interface. We find a closed form expression for an effective-on rate which depends on reactants distributions, and derive the conditions for optimizing such reactions. Interestingly, the model reveals that maximum reaction rate is not necessarily obtained when the concentration profiles of the reacting species perfectly overlap. In addition to the exact solutions, we derive throughout several closed form engineering approximations which are based on elementary functions and are simple to implement, yet maintain the interplay between the important scales. Both the exact and approximate solutions provide insight into sample focusing and can be used to design and optimize ITP-based assays.

60 APPLIED LIFE SCIENCES↗

Competitive growth mechanisms of aluminum nitride thin films deposited by off-normal reactive magnetron sputtering

We have recently shown that AlN (0002) (c axis) is tilted abruptly toward the deposition direction as N{sub 2} concentration is increased in N{sub 2}/Ar sputtering gas mixtures. Here, we present a Monte Carlo simulation model to describe the phenomenon of sudden c-axis AlN tilt. The model is based on the assumption that AlN islands with their c axis parallel to substrate normal and AlN islands with tilted c axis coexist at the initial stages of the growth and they can provide the adatoms with different surface mobilities. It is believed that the adatom mobilities are quenched when N{sub 2} concentration reaches a certain amount in the reactive sputtering of AlN. Our model further assumes that adatom mobility differences on different islands result in a growth rate difference of the islands. At the initial stages of the growth, AlN islands with tilted c axis grow taller due to the lower adatom mobility on these islands. As they grow taller, they win the competition and stop the further growth of AlN islands with their c axis parallel to substrate normal due to shadowing effect. Monte Carlo simulations revealed that the shadowing effect combined with different adatom mobilities promotes the sudden c-axis tilt in AlN thin films.

36 MATERIALS SCIENCE↗

Phase-field modeling of void evolution and swelling in materials under irradiation

Void swelling is an important phenomenon observed in both nuclear fuels and cladding materials in operating nuclear reactors. In this work we developed a phase-field model to simulate the void nucleation, growth, and the change of void volume fraction. Important material processes including the generation of defects such as vacancies and self-interstitials, their diffusion and annihilation, and void nucleation and evolution have been taken into account in our phase-field model. The thermodynamic and kinetic properties such as chemical free energy, interfacial energy, vacancy mobility, and annihilation rate of vacancies and interstitials are generally expressed as functions of the temperature. The developed model enables one to parametrically study critical void nucleus size, void growth kinetics, and void volume fraction evolutions. Our simulations demonstrated that the volume swelling displays a quasi-bell shape distribution with temperature that was often observed in experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Revisiting thermodynamics and kinetic diffusivities of uranium–niobium with Bayesian uncertainty analysis

In this paper, thermodynamic and kinetic diffusivities of uranium–niobium (U–Nb) are re-assessed by means of the CALPHAD (CALculation of PHAse Diagram) methodology. In order to improve the consistency and reliability of the assessments, first-principles calculations are coupled with CALPHAD. In particular, heats of formation of γ -U–Nb are estimated and verified using various density-functional theory (DFT) approaches. These thermochemistry data are then used as constraints to guide the thermodynamic optimization process in such a way that the mutual-consistency between first-principles calculations and CALPHAD assessment is satisfactory. In addition, long-term aging experiments are conducted in order to generate new phase equilibria data at the γ 2 /α+γ 2 boundary. These data are meant to verify the thermodynamic model. Assessment results are generally in good agreement with experiments and previous calculations, without showing the artifacts that were observed in previous modeling. The mutual-consistent thermodynamic description is then used to evaluate atomic mobility and diffusivity of γ-U–Nb. Finally, Bayesian analysis is conducted to evaluate the uncertainty of the thermodynamic model and its impact on the system's phase stability.

36 MATERIALS SCIENCE↗