Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer hardware”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

SEE Test Results for SAMA5D3

ARM processors power a class of high-performance, lower power system on a chip devices. In the absence of radiation effects, these devices are highly desirable for space use. The processor core architecture for ARM devices is licensed to provide computing on multiple hardware platforms. The A5 processor is in a unique pioneering space for providing detailed radiation response data to explore the baseline performance of these devices. These data can help set options for ARM processors and possibly impact design choices for the next generation of ARM fault tolerance capabilities. The SAMA5D3 was tested to establish general SEE performance for a relatively simple implementation of the ARM A5 core. This testing observed SRAM sensitivity starting at an LET of about 3 MeV-cm2/mg, with a saturated cross section of about 2x10-8cm2/bit, and this was determined by both active write and read of the caches, in addition to the use of a debugger to provide test results. Crash/SEFI data was collected using both Linux and bare metal C-code. The onset LET for crashes was about LET 1.5 MeV-cm2/mg, with saturated cross sections of about 2x10-5 cm2 for bare metal (low utilization), and 2x10-4cm2 for Linux (high utilization) tests.

Daniel, Andrew C.↗

3D Characterization and Time-Lapse Imaging of the Desiccation Treatability Test at the Hanford BC-Cribs and Trenches Site using High Performance Computing applied to Electrical Resistivity Imaging - 12271

Contaminated vadose zone materials are a potential source of long-term groundwater contamination at many sites across the Department of Energy (DOE) complex. Deep vadose zone contamination presents a particularly challenging remedial problem due to the difficultly of locating contaminants and the expense of access and ex situ treatment. In situ remediation techniques, whereby remedial amendments must be delivered to contaminated soils, have been identified as a potential alternative. However, amendment delivery is typically uncertain and post delivery remedial performance is often not well understood due to limited information available from sparsely spaced boreholes. Recent advancements in electrical resistivity tomography (ERT) are being used to address these challenges at the Hanford site by providing remote, three-dimensional images of contaminant distribution and four-dimensional (three spatial dimensions plus the time dimension) images of in-situ vadose zone remediation processes. These capabilities were recently demonstrated with a large scale surface characterization effort and during a smaller scale desiccation treatability test at the Hanford BC-Cribs area. The results of these efforts demonstrate the utility of leveraging high-performance computing resources to process ERT data for 3D reconnaissance mapping of subsurface contaminants and for detailed 3D monitoring of vadose zone remediation efforts. Two examples of ERT imaging at a former waste disposal facility have been demonstrated at different scales; a large scale reconnaissance survey spanning many hundreds of meters and a detailed monitoring application spanning a few tens of meters. Although ERT is applicable at many scales, resolution is generally governed by proximity to electrodes. For instance, the BCCT reconnaissance survey demonstrated herein lost resolution with depth (i.e. away from surface electrodes), and was unable to detect a high conductivity anomaly at approximately 75 m below ground surface in the cribs area; the deep anomalies were detected during highly focused borehole sampling. Conversely, the desiccation site characterization and monitoring demonstrated high resolution at a small scale, but only because of close proximity to survey electrodes. Although proximity to electrodes is not the only factor governing ERT resolution, it is often the primary factor for determining how an ERT system should be effectively deployed for a given application. Regardless of resolution limitations, the utility of ERT for remotely detecting wastes and monitoring subsurface processes is evident. ERT imaging is not a final detection or monitoring solution alone, but provides a necessary capability to remotely detect subsurface conditions and understand subsurface processes. Such a capability can significantly increase the efficacy and reduce the cost of remediation by guiding sampling efforts and informing remedial system design and operation. However, given the computational demands of 3D ERT characterization and monitoring inversions, the full imaging capability enabled by contemporary ERT survey systems can generally only be realized with high performance computing resources, both hardware and software. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ATHENA: Analytical Tool for Heterogeneous Neuromorphic Architectures

The ASC program seeks to use machine learning to improve efficiencies in its stockpile stewardship mission. Moreover, there is a growing market for technologies dedicated to accelerating AI workloads. Many of these emerging architectures promise to provide savings in energy efficiency, area, and latency when compared to traditional CPUs for these types of applications — neuromorphic analog and digital technologies provide both low-power and configurable acceleration of challenging artificial intelligence (AI) algorithms. If designed into a heterogeneous system with other accelerators and conventional compute nodes, these technologies have the potential to augment the capabilities of traditional High Performance Computing (HPC) platforms [5]. This expanded computation space requires not only a new approach to physics simulation, but the ability to evaluate and analyze next-generation architectures specialized for AI/ML workloads in both traditional HPC and embedded ND applications. Developing this capability will enable ASC to understand how this hardware performs in both HPC and ND environments, improve our ability to port our applications, guide the development of computing hardware, and inform vendor interactions, leading them toward solutions that address ASC’s unique requirements.

97 MATHEMATICS AND COMPUTING↗

Adaptive Instrument Module: Space Instrument Controller "Brain" through Programmable Logic Devices

The Adaptive Instrument Module (AIM) will be the first true demonstration of reconfigurable computing with field-programmable gate arrays (FPGAs) in space, enabling the 'brain' of the system to evolve or adapt to changing requirements. In partnership with NASA Goddard Space Flight Center and the Australian Cooperative Research Centre for Satellite Systems (CRC-SS), APL has built the flight version to be flown on the Australian university-class satellite FEDSAT. The AIM provides satellites the flexibility to adapt to changing mission requirements by reconfiguring standardized processing hardware rather than incurring the large costs associated with new builds. This ability to reconfigure the processing in response to changing mission needs leads to true evolveable computing, wherein the instrument 'brain' can learn from new science data in order to perform state-of-the-art data processing. The development of the AIM is significant in its enormous potential to reduce total life-cycle costs for future space exploration missions. The advent of RAM-based FPGAs whose configuration can be changed at any time has enabled the development of the AIM for processing tasks that could not be performed in software. The use of the AIM enables reconfiguration of the FPGA circuitry while the spacecraft is in flight, with many accompanying advantages. The AIM demonstrates the practicalities of using reconfigurable computing hardware devices by conducting a series of designed experiments. These include the demonstration of implementing data compression, data filtering, and communication message processing and inter-experiment data computation. The second generation is the Adaptive Processing Template (ADAPT) which is further described in this paper. The next step forward is to make the hardware itself adaptable and the ADAPT pursues this challenge by developing a reconfigurable module that will be capable of functioning efficiently in various applications. ADAPT will take advantage of radiation tolerant RAM-based field programmable gate array (FPGA) technology to develop a reconfigurable processor that combines the flexibility of a general purpose processor running software with the performance of application specific processing hardware for a variety of high performance computing applications.

Darrin, Ann Garrison↗

Analog architectures for neural network acceleration based on non-volatile memory

Analog hardware accelerators, which perform computation within a dense memory array, have the potential to overcome the major bottlenecks faced by digital hardware for data-heavy workloads such as deep learning. Exploiting the intrinsic computational advantages of memory arrays, however, has proven to be challenging principally due to the overhead imposed by the peripheral circuitry and due to the non-ideal properties of memory devices that play the role of the synapse. We review the existing implementations of these accelerators for deep supervised learning, organizing our discussion around the different levels of the accelerator design hierarchy, with an emphasis on circuits and architecture. We explore and consolidate the various approaches that have been proposed to address the critical challenges faced by analog accelerators, for both neural network inference and training, and highlight the key design trade-offs underlying these techniques.

97 MATHEMATICS AND COMPUTING↗

Integrated Modeling of Advanced Opto-Mechanical Systems

The design of optical hardware for space applications is particularly challenging when developing high performance, novel systems that have no precedent. Integrated modeling and analysis of such opto-mechanical systems seeks to describe the end-to-end performance of the hardware using mission-relevant metrics. This multidisciplinary analysis might start with thermal disturbances from observation maneuvers, compute the system temperatures, compute the distorted positions and shapes of the hardware and compute the resulting optical performance. Dynamic disturbances such as reaction wheel imbalance or inertia imbalance of optical delay lines might be applied to a structural dynamic model and used in a guidance and control analysis. Mission-relevant science metrics might include wavefront quality, pointing error or imaging stability. Assembling a tool chain that can be both nimble and effective when scaled to the high fidelity models of detail design has been challenging. An integrated thermal, mechanical and optical analysis capability suitable for detail design has been developed and verified through experimental measurement. This capability was used in the design of flight-like breadboard hardware and development of a test apparatus that established both the level of performance of the hardware and the validity of the analysis. The analysis includes prediction of the thermal environment of the test chamber, detailed temperature distributions on the breadboard hardware, fine scale deformations of the optical elements, and computation of the wavefront quality using geometric optics. A battery of tests were conducted to assess the experiment data acquisition, measurement and control system and to establish the performance of the hardware design and accuracy of the integrated modeling. Thermal loads that represent operational observing maneuvers were imposed and the hardware optical performance was measured and compared to analytical predictions.

optomechanical analysis↗

Hybrid Quantum-Classical Neural Networks

Deep learning is one of the most successful and far-reaching strategies used in machine learning today. However, the scale and utility of neural networks is still greatly limited by the current hardware used to train them. These concerns have become increasingly pressing as conventional computers are soon expected to approach the physical limitations that will slow their performance improvements in the near future. For these reasons, scientists have begun to explore alternative computing platforms, like quantum computers, for training neural networks. In recent years, variational quantum circuits have emerged as one of the most successful approaches to quantum deep learning on noisy intermediate scale quantum devices. We propose a hybrid quantum-classical neural network architecture where each neuron is a variational quantum circuit. We empirically analyze the performance of this hybrid neural network on a series of binary classification data sets using a simulated IBM universal quantum computer and a state-of-the-art IBM universal quantum computer. On the simulated hardware, we observe that the hybrid neural network achieves around 10% higher classification accuracy and 20% better minimization of the cost function than an individual variational quantum circuit. On the quantum hardware, we observe that each model only performs well when the qubit and gate count is sufficiently small.

Arthur, Davis↗

Numerical propulsion system simulation

The cost of implementing new technology in aerospace propulsion systems is becoming prohibitively expensive. One of the major contributors to the high cost is the need to perform many large scale system tests. Extensive testing is used to capture the complex interactions among the multiple disciplines and the multiple components inherent in complex systems. The objective of the Numerical Propulsion System Simulation (NPSS) is to provide insight into these complex interactions through computational simulations. This will allow for comprehensive evaluation of new concepts early in the design phase before a commitment to hardware is made. It will also allow for rapid assessment of field-related problems, particularly in cases where operational problems were encountered during conditions that would be difficult to simulate experimentally. The tremendous progress taking place in computational engineering and the rapid increase in computing power expected through parallel processing make this concept feasible within the near future. However it is critical that the framework for such simulations be put in place now to serve as a focal point for the continued developments in computational engineering and computing hardware and software. The NPSS concept which is described below will provide that framework.

R.W. Claus↗

Numerical propulsion system simulation

The cost of implementing new technology in aerospace propulsion systems is becoming prohibitively expensive. One of the major contributors to the high cost is the need to perform many large scale system tests. Extensive testing is used to capture the complex interactions among the multiple disciplines and the multiple components inherent in complex systems. The objective of the Numerical Propulsion System Simulation (NPSS) is to provide insight into these complex interactions through computational simulations. This will allow for comprehensive evaluation of new concepts early in the design phase before a commitment to hardware is made. It will also allow for rapid assessment of field-related problems, particularly in cases where operational problems were encountered during conditions that would be difficult to simulate experimentally. The tremendous progress taking place in computational engineering and the rapid increase in computing power expected through parallel processing make this concept feasible within the near future. However it is critical that the framework for such simulations be put in place now to serve as a focal point for the continued developments in computational engineering and computing hardware and software. The NPSS concept which is described will provide that framework.

Lytle, John K.↗

Low-cost data analysis systems for processing multispectral scanner data

A research-oriented data analysis system was developed which is used for evaluating complex remote sensor systems and for development of techniques for application of remotely sensed data. Some modular hardware components were developed which may be added to one's existing facilities to establish a low-cost data analysis system for processing multispectral scanner data. Software modules which are compatible with small general purpose digital computers process and analyze remote sensor data, and convert it to information needed by users. The software modules are written in FORTRAN IV language for ease of transfer to other computer systems. The basic hardware and software system requirements are defined for some low-cost data analysis systems consisting of an image display system, a small general purpose digital computer, and an output recording device. The hardware modules consist of: a LANDSAT MSS data reformatting program; a series of spectral pattern recognition programs required to generate surface classification maps and tabular information; programs to convert computer generated maps from image space to a geographically referenced base; programs to extract data and irregularly shaped areas and to produce thematic maps of the designated areas; and programs to tabulate acreages of selected classification categories. Some off-the-shelf, inexpensive digital image display systems are described.

Whitley, S. L.↗

hPIC2: A hardware-accelerated, hybrid particle-in-cell code for dynamic plasma-material interactions

The exascale era of high performance computing promises to bring the field of computational plasma physics ever closer to the goal of accurate multiscale modeling. Such computers will rely on hardware acceleration to offload work to dedicated components, notably general-purpose graphics processing units (GPUs). However, devices from different manufacturers require software to be written with different parallel programming models, greatly increasing the code maintenance burden of applications designed to perform on more than one such device. hPIC2 is a hybrid plasma simulation code developed with the Kokkos performance portability framework to target the architectures that will drive exascale computing for the foreseeable future. As a hybrid simulation code, hPIC2 investigates the simultaneous use of various plasma models on the same domain, at the same time. hPIC2 also optionally couples to RustBCA, which accurately models ion-material interactions using the binary collision approximation (BCA) method. In conclusion, hPIC2 therefore achieves scalable performance on a variety of computing architectures when simulating complex and diverse plasmas, particularly near plasma-material interfaces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ESTL tracking and data relay satellite /TDRSS/ simulation system

The Tracking Data Relay Satellite System (TDRSS) provides single access forward and return communication links with the Shuttle/Orbiter via S-band and Ku-band frequency bands. The ESTL (Electronic Systems Test Laboratory) at Lyndon B. Johnson Space Center (JSC) utilizes a TDRS satellite simulator and critical TDRS ground hardware for test operations. To accomplish Orbiter/TDRSS relay communications performance testing in the ESTL, a satellite simulator was developed which met the specification requirements of the TDRSS channels utilized by the Orbiter. Actual TDRSS ground hardware unique to the Orbiter communication interfaces was procured from individual vendors, integrated in the ESTL, and interfaced via a data bus for control and status monitoring. This paper discusses the satellite simulation hardware in terms of early development and subsequent modifications. The TDRS ground hardware configuration and the complex computer interface requirements are reviewed. Also, special test hardware such as a radio frequency interference test generator is discussed.

Kapell, M. H.↗

Parallelization of Finite Element Analysis Codes Using Heterogeneous Distributed Computing

Performance gains in computer design are quickly consumed as users seek to analyze larger problems to a higher degree of accuracy. Innovative computational methods, such as parallel and distributed computing, seek to multiply the power of existing hardware technology to satisfy the computational demands of large applications. In the early stages of this project, experiments were performed using two large, coarse-grained applications, CSTEM and METCAN. These applications were parallelized on an Intel iPSC/860 hypercube. It was found that the overall speedup was very low, due to large, inherently sequential code segments present in the applications. The overall execution time T(sub par), of the application is dependent on these sequential segments. If these segments make up a significant fraction of the overall code, the application will have a poor speedup measure.

Ozguner, Fusun↗

CFD Vision 2030 Study: A Path to Revolutionary Computational Aerosciences

This report documents the results of a study to address the long range, strategic planning required by NASA's Revolutionary Computational Aerosciences (RCA) program in the area of computational fluid dynamics (CFD), including future software and hardware requirements for High Performance Computing (HPC). Specifically, the "Vision 2030" CFD study is to provide a knowledge-based forecast of the future computational capabilities required for turbulent, transitional, and reacting flow simulations across a broad Mach number regime, and to lay the foundation for the development of a future framework and/or environment where physics-based, accurate predictions of complex turbulent flows, including flow separation, can be accomplished routinely and efficiently in cooperation with other physics-based simulations to enable multi-physics analysis and design. Specific technical requirements from the aerospace industrial and scientific communities were obtained to determine critical capability gaps, anticipated technical challenges, and impediments to achieving the target CFD capability in 2030. A preliminary development plan and roadmap were created to help focus investments in technology development to help achieve the CFD vision in 2030.

Jeffrey P Slotnick↗

More About Software for No-Loss Computing

A document presents some additional information on the subject matter of "Integrated Hardware and Software for No- Loss Computing" (NPO-42554), which appears elsewhere in this issue of NASA Tech Briefs. To recapitulate: The hardware and software designs of a developmental parallel computing system are integrated to effectuate a concept of no-loss computing (NLC). The system is designed to reconfigure an application program such that it can be monitored in real time and further reconfigured to continue a computation in the event of failure of one of the computers. The design provides for (1) a distributed class of NLC computation agents, denoted introspection agents, that effects hierarchical detection of anomalies; (2) enhancement of the compiler of the parallel computing system to cause generation of state vectors that can be used to continue a computation in the event of a failure; and (3) activation of a recovery component when an anomaly is detected.

Edmonds, Iarina↗

State preparation and evolution in quantum computing: a perspective from Hamiltonian moments

Quantum algorithms on the noisy intermediate-scale quantum (NISQ) devices are expected to simulate quan- tum systems that are classically intractable to demonstrate quantum advantages. However, the non-negligible gate error on the NISQ devices impedes the conventional quantum algorithms to be implemented. Practical strategies usually exploit hybrid quantum-classical quantum algorithms to demonstrate potentially useful ap- plications of quantum computing in the NISQ era. Among the numerous hybrid quantum-classical algorithms, recent efforts highlight the development of quantum algorithms based upon quantum computed Hamiltonian moments, ?f|Hˆn|f? (n = 1, 2, · · · ), with respect to quantum state |f?. In this tutorial, we will give a brief review of these quantum algorithms with focuses on the typical ways of computing Hamiltonian moments using quantum hardware and improving the accuracy of the estimated state energies based on the quantum computed moments. Furthermore, we will present a tutorial to show how we can measure and compute the Hamiltonian moments of a four-site Heisenberg model, and compute the energy and magnetization of the model utilizing the imaginary time evolution in the real IBM-Q NISQ hardware environment. Along this line, we will further discuss some practical issues associated with these algorithms. We will conclude this tutorial review by overviewing some possible developments and applications in this direction in the near future.

Aulicino, Joseph C.↗

GPU-friendly surface model for Monte-Carlo detector simulations

The demands for Monte-Carlo simulation are drastically increasing with the Large Hadron Collider’s high-luminosity upgrade, and are expected to exceed the currently available compute resources. At the same time, modern high-performance computing has adopted powerful hardware accelerators, particularly GPUs. The AdePT and Celeritas projects aim to address the demanding computational needs by leveraging these heterogeneous computing architectures. While both have successfully ported realistic detector simulations to GPUs using the VecGeom library, the complexity of geometry modeling emerged as a bottleneck. Thread divergence and high register usage were degrading the GPU performance. Therefore, a new, GPU-friendly surface-based model has been introduced in the VecGeom library that decomposes the divergent code of the 3D primitive solids into simpler and more balanced surface algorithms. In this work, we present the latest developments, focusing on the additions required to efficiently model complex setups like the CMS Phase-2 geometry. This includes memory reduction techniques, and adding accelerating structures for faster traversal.

Diederichs, Severin [CERN]↗

Thermal Management for FPGA Nodes in HPC Systems

The integration of FPGAs into large-scale computing systems is gaining attention. In these systems, real-time data handling for networking, tasks for scientific computing, and machine learning can be executed with customized datapaths on reconfigurable fabric within heterogeneous compute nodes. At the same time, thermal management, particularly battling the cooling cost and guaranteeing the reliability, is a continuing concern. The introduction of new heterogeneous components into HPC nodes only adds further complexities to thermal modeling and management. The thermal behavior of multi-FPGA systems deployed within large compute clusters is less explored. Here, we first show that the thermal behaviors of different FPGAs of the same generation can vary due to their physical locations in a rack and process variation, even though they are running the same tasks. We present a machine learning–based model to capture the thermal behavior of each individual FPGA in the cluster. We then propose two thermal management strategies guided by our thermal model. First, we mitigate thermal variation and hotspots across the cluster by proactive thermal-aware task placement. Under the tested system and benchmarks, we achieve up to 26.4° C and on average 13.3° C system temperature reduction with no performance penalty. Second, we utilize this thermal model to guide HLS parameter tuning at the task design stage to achieve improved thermal response after deployment.

97 MATHEMATICS AND COMPUTING↗