Search NASA⌕ Search

SEARCH · Search NASA

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Prediction of novel hard phases of Si{sub 3}N{sub 4}: First-principles calculations

Exploration of novel hard metastable phases of silicon nitride was performed using a recently developed particle-swarm optimization method within the CALYPSO software package. Three potential hard metastable phases of t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} were predicted. These phases are mechanically and dynamically stable at ambient pressure based on their elastic constants and phonon dispersions. t-Si{sub 3}N{sub 4} and m-Si{sub 3}N{sub 4} exhibit lower energies than γ-Si{sub 3}N{sub 4} at pressures below 2.5 GPa and 2.9 GPa, respectively, which promise that the formers could be obtained by quenching from γ-Si{sub 3}N{sub 4}. o-Si{sub 3}N{sub 4} is a better high-pressure metastable phase than CaTi{sub 2}O{sub 4}-type Si{sub 3}N{sub 4} proposed by Tatsumi et al. and it can come from the transition of γ-Si{sub 3}N{sub 4} under 198 GPa. The theoretical band gaps of t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} at ambient pressure were 3.15 eV, 3.90 eV, and 3.36 eV, respectively. At ambient pressure, the Vickers hardness values of t-Si{sub 3}N{sub 4} (32.6 GPa), m-Si{sub 3}N{sub 4} (31.5 GPa), and o-Si{sub 3}N{sub 4} (36.1 GPa) are comparable to β-Si{sub 3}N{sub 4} and γ-Si{sub 3}N{sub 4}. With the pressure increasing, t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4} will change from the brittle to ductile state at about 15.7 GPa, 7.3 GPa and 28.9 GPa, respectively. - Graphical abstract: This figure shows the crystal structures of three Si{sub 3}N{sub 4} predicted in this manuscript, and left to right: t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4} and o-Si{sub 3}N{sub 4}. - Highlights: • We explored three metastable phases of Si{sub 3}N{sub 4} — t-Si{sub 3}N{sub 4}, m-Si{sub 3}N{sub 4}, and o-Si{sub 3}N{sub 4}. • The enthalpies of t and m- are much lower than that of γ at ambient pressure. • ois one further high pressure phase than γ. • o-Si{sub 3}N{sub 4} is the most hardest phase in Si{sub 3}N4 system. • Increasing pressure will change them from brittle to ductile state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aging behavior and mechanical properties of maraging steels in the presence of submicrocrystalline Laves phase particles

Cold rolling and annealing of homogenized Fe-Ni-Mn-Mo-Ti-Cr maraging steels resulted in the formation of submicrocrystalline Fe{sub 2}(Mo,Ti) Laves phase particles. Optical and scanning electron microscopy, X-ray diffraction, tensile and hardness tests were used to study the microstructure, aging behavior and mechanical properties of the annealed steels. The annealed microstructures showed age hardenability during subsequent isothermal aging at 753 K. Ultrahigh fracture stress but poor tensile ductility was obtained after substantial age hardening in the specimens with 2% and 4% chromium. Increasing chromium addition up to 6% toughened the aged microstructure at the expense of the fracture stress by increasing the volume fraction of retained austenite. The Laves phase particles acted as crack nucleation sites during tensile deformation. - Highlights: {yields} Laves phases dispersed in a BCC iron matrix by annealing of cold rolled samples. {yields} The samples showed age hardenability during subsequent isothermal aging at 753 K. {yields} Ultrahigh fracture stress but poor ductility was obtained after age hardening. {yields} Increasing chromium addition toughened the aged microstructure. {yields} Laves phase particles acting as crack nucleation sites during tensile deformation.

36 MATERIALS SCIENCE↗

Quantitative investigation of the tensile plastic deformation characteristic and microstructure for friction stir welded 2024 aluminum alloy

The effect of the microstructure heterogeneity on the tensile plastic deformation characteristic of friction stir welded (FSW) 2024 aluminum alloy was investigated for the potential applications on light weight design of vehicles. The microstructure characteristics of the FSW joints, such as the grain structure, dislocation density and the distribution of precipitation, were studied by electron backscattered diffraction (EBSD) and transmission electron microscopy (TEM). The tensile deformation characteristic of the FSW joints was examined using the automatic strain measuring system (ASAME) by mapping the global and local strain distribution, and then was analyzed by mechanics calculation. It is found that the tensile deformation of the FSW joints is highly heterogeneous leading to a significant decrease in global ductility. The FSW joints mainly contain two typical deformation zones, which show great effect on the regional inhomogeneous deformation. One is the nugget zone (NZ) with a region of 8 mm in width, and the other is part of the BM with a region of 10 mm in width. The BM of the joints is the weakest region where the strain localizes early and this localization extends until fracture with a strain over 30%, while the strain in the NZ is only 4%. Differences in regional strain of FSW joints, which are essentially controlled by grain structure, the distribution of precipitation and dislocation density, result in decrease on the overall mechanical properties. - Highlights: Black-Right-Pointing-Pointer Microstructure heterogeneity of welds on tensile deformation behavior is studied. Black-Right-Pointing-Pointer The welds contain two typical deformation zones, affecting the global ductility. Black-Right-Pointing-Pointer Regional strain of welds is controlled by grain structure and dislocation density. Black-Right-Pointing-Pointer Theoretical calculation is in good agreement with experimental result.

36 MATERIALS SCIENCE↗

Effect of substrates on microstructure and mechanical properties of nano-eutectic 1080 steel produced by aluminothermic reaction

Nano-eutectic bulk 1080 carbon steel was prepared on glass and copper substrates by an aluminothermic reaction casting. The microstructure of the steel was analyzed by an optical microscope, transmission electron microscopy, an electron probe micro-analyzer, a scanning electron microscope and X-ray diffraction. Results show that the microstructure of the steel consisted of a little cementite and lamellar eutectic pearlite. Average lamellar spacing of the pearlite prepared on copper and glass substrates was about 230 nm and 219 nm, respectively. Volume fraction of the pearlite of the two steels was about 95%. Hardness of the steel was about 229 and 270 HV. Tensile strength was about 610 and 641 MPa and tensile elongation was about 15% and 8%. Compressive strength was about 1043 and 1144 MPa. Compared with the steel prepared on copper substrate, the steel prepared on glass substrate had smaller lamellar spacing of the pearlite phase and higher strength, and low ductility due to the smaller spacing. - Highlights: • 1080-carbon steels were successfully prepared by an aluminothermic reaction casting. • Lamellar spacing of the nanoeutetic pearlite is less than 250 nm. • The compressive strength of the steel is about 1144 MPa. • The tensile ductility of the steel is about 15%.

36 MATERIALS SCIENCE↗

Grain size dependence of dynamic mechanical behavior of AZ31B magnesium alloy sheet under compressive shock loading

The effects of grain size on the dynamic deformation behavior of rolled AZ31B alloy at high strain rates were investigated. Rolled AZ31B alloy samples with grain sizes of 6, 18 and 37 μm, were subjected to shock loading tests using Split Hopkinson Pressure Bar at room temperature and at a strain rate of 1100 s{sup −} {sup 1}. It was found that a double-peak basal texture formed in the shock loaded samples. The strength and ductility of the alloy under the high strain-rate compressive loading increased with decreasing grain size. However, twinning fraction and strain hardening rate were found to decrease with decreasing grain size. In addition, orientation imaging microscopy showed a higher contribution of double and contraction twins in the deformation process of the coarse-grained samples. Using transmission electron microscopy, pyramidal dislocations were detected in the shock loaded sample, proving the activation of pyramidal slip system under dynamic impact loading. - Highlights: • A double-peak basal texture developed in all shock loaded samples. • Both strength and ductility increased with decreasing grain size. • Twinning fraction and strain hardening rate decreased with decreasing grain size. • ‘g.b’ analysis confirmed the presence of dislocations in shock loaded alloy.

36 MATERIALS SCIENCE↗

Infiltrated W–Cu composites with combined architecture of hierarchical particulate tungsten and tungsten fibers

In this article, novel W–Cu composites reinforced with topologically-inserted tungsten fibers (W{sub f}) have been fabricated by hot-press sintering and infiltration method. By pre-sputtering of ~ 100 nm thick chromium layer onto the surface of W{sub f}, the contiguity or connectivity between W{sub f} and neighboring tungsten particles (W{sub p}) or Cu after sintering and infiltration was enhanced. Combined SEM, TEM and STEM techniques confirmed that the intact interfaces of W{sub f}/W{sub p} and W{sub f}/Cu free from precipitates, impurities and porosities would provide desirable strength and ductility. Further mechanical tests also validated its superior compressive strength and plasticity at various temperatures, together with significantly improved tensile strength (by 23.6%) and hardness (by 9.3%) for the W–Cu composite after reinforcement with Cr-coated W{sub f}, which promotes the engineering application of the composite greatly. - Highlights: • W-fibers reinforced W–Cu composites were fabricated by sintering and infiltration. • The sputtered Cr onto W{sub f} has dissolved into adjacent W{sub f} and W{sub p} during fabrication. • The intact interfaces of W{sub f}/W{sub p} and W{sub f}/Cu confer enhanced strength and ductility. • Tensile strength and hardness improve by 23.6% and 9.3% after interface tuning.

36 MATERIALS SCIENCE↗

The effect of scandium addition on microstructure and mechanical properties of Al–Si–Mg alloy: A multi-refinement modifier

Effect of scandium (Sc) additions on the microstructure, mechanical properties and fracture behavior of Al–Si–Mg casting alloy (F357) were systematically investigated. It was found that Sc addition caused a multi-refining efficiency on the microstructure of as-cast F357 alloy, including refinement of grains and secondary dendrite arm spacing (SDAS), modification of eutectic Si and harmless disposal of β-Al{sub 5}FeSi phase. Subsequent T6 heat treatment had further induced the complete spheroidization of eutectic Si and precipitation of fine secondary Al{sub 3}Sc dispersoids in the Sc modified alloys. Thus the mechanical properties, especially the ductility, were significantly enhanced by the addition of Sc combined with the heat treatment. The highest ultimate tensile strength, yield strength and elongation were achieved in 0.8 wt.% Sc modified F357 alloy combined with T6 heat treatment. Furthermore, fractographic examinations indicated that the ductile fracture mechanism served as a dominate role in the modified alloys due to the formation of fine, deep and uniformly distributed dimples. - Highlights: • Detailed characterization of the multi-refining microstructure of Sc modified F357 alloy was performed. • The multi-refinement was proposed to refine grain and SDAS, modify eutectic Si and β-phase. • Sc modifier combined with T6 treatment is effective in improving tensile properties. • Modification of eutectic Si in F357 alloy with Sc is consistent with the IIT mechanism.

36 MATERIALS SCIENCE↗

Microstructural evolution and mechanical properties on an ARB processed IF steel studied by X-ray diffraction and EBSD

Accumulative Roll Bonding (ARB) is one of the so-called severe plastic deformation (SPD) processes, allowing the production of metals and alloys with ultrafine (micro-nano) structures. Materials with ultrafine grains present attractive properties like the simultaneous increase in strength and ductility. Our interest in these materials is focused on their microstructural evolution during ARB processing, eventually responsible for the enhancement of those mechanical properties. In the current work we follow the evolution of the microstructure in an interstitial-free (IF) steel deformed by ARB after consecutive processing cycles, by means of Electron BackScatter Diffraction (EBSD) and X-ray diffraction (XRD). Particularly, we present results related to texture, grain (GS) and domain sizes, grain boundary character, density of Geometrically Necessary Dislocations (GND), Grain Orientation Spread (GOS), lattice parameters, microstrain, dislocation density and their spatial arrangement. After 5 ARB cycles the system shows a microstructure constituted mainly by submicrometric grains with high angle boundaries and low presence of dislocations inside the grains. - Highlights: •The evolution of microstructure is followed simultaneously by using GAM, GOS and GND (EBSD) and XRD. •LAGBs and subgrains disappear after few cycles SSDs and HAGBs persist at the end. •Dynamic recrystallization counterbalances dislocation arrays and diminishes hardening rate. •Grain size stabilization is revealed as a mechanism for increasing ductility after few ARB cycles.

36 MATERIALS SCIENCE↗

Microscopic deformation compatibility during monotonic loading in a Mg-Gd-Y alloy

Microscopic deformation compatibility is a key in achieving high ductility in polycrystalline magnesium alloys. This paper presents a grain-level compatibility investigation of Mg-Gd-Y alloy using in-situ tension in scanning electron microscopy (SEM) combined with electron back scattered diffraction (EBSD) and digital image correlation (DIC) techniques. The results show that strain amplitudes are not always higher in grains with high Schmid factors of basal slip. Thus, the Schmid law can hardly predict the strain amplitudes at grain level. In addition, the average intergranular strains are higher than the average intragranular strain and a strong surrounding effect grain-to-grain was found. A slip-transfer parameter m′, describing the surrounding effect, was used to evaluate the deformation compatibility. It is found that a high m′ value and a high Schmid factor of certain slip system in the adjacent grains would result in a good compatibility around grain boundaries and could accommodate higher local strains, which would improve the ductility of magnesium alloys. - Highlights: •Microstructure based DIC analyses have been performed on a Mg-Gd-Y alloy. •Strain amplitudes are higher at grain boundary areas than grain interiors. •Schmid Law is not applicable for predicting the strain amplitudes. •A geometric parameter m′ can effectively evaluate strain.

36 MATERIALS SCIENCE↗

Enhancing the tensile properties of EBM as-built thin parts: Effect of HIP and chemical etching

Highlights: • The EBM process leads to important cross section variations in thin parts. • Stress calculation must be based on the average section in order to be relevant. • As-built state has a detrimental effect on every mechanical property. • Mechanical properties of machined samples are met with chemical etching. • HIP has a beneficial effect on the ductility. - Abstract: As-built Ti-6Al-4 V thin parts were manufactured using Electron Beam Melting (EBM) and characterized by optical microscopy and laboratory X-ray tomography in order to observe their microstructure, pore distribution and surface aspect. Chemical etching and HIP post-treatments were applied to as-built samples and their effect on the material and static mechanical properties were studied. Tensile tests were performed on both as-built and post-treated samples and their results compared to the ones reported in the literature for machined EBM samples. Because of the significant variations of the cross section observed along the gauge length, the calculation of the tensile stresses is not straightforward. Three simple sections were measured from the tomography scans. The average section along the gauge length was considered as the most suitable. The tensile mechanical properties of the as-built samples were studied and a detrimental effect of the surface state on the yield strength, ultimate tensile strength and elongation to failure was observed. Smoothing of the surface irregularities induced by chemical etching provoked an increase of those mechanical properties whereas the change of the microstructure generated by the HIP treatment leads to a decrease of the material strength that goes along with an increase of the ductility. Down scaling factors were proposed in order to take into account the sample state, as-built or post-treated.

36 MATERIALS SCIENCE↗

Effect of trace amounts of added Sc on microstructure and mechanical properties of 2055 aluminum alloy

Highlights: • Effect of trace Sc on microstructure and mechanical properties in 2055 Al-alloy was investigated. • T{sub 1} is the main strengthening phase in Sc free and Sc added 2055 alloy at the aging temperature of 175°C and 200°C. • The refinement of T{sub 1} by Sc addition depends on the aging temperature. • Mechanical properties were deteriorated by Sc at the aging temperature of 175°C and improved at 200°C aging treatment. - Abstract: The effects of Sc additions and isothermal aging on the microstructure and mechanical properties of 2055 aluminum alloy have been investigated. The isothermal aging temperatures investigated were 175 °C and 200 °C. Results show that the aging temperature does not affect the type of precipitates in both Sc-free and Sc-added 2055 Al alloys. While remarkable changes in the size and number density of T{sub 1} (Al{sub 2}CuLi) precipitates have been observed. For samples aged at 175 °C for 8 h, the average length of T{sub 1} precipitates was increased from 39.9 nm to 45.6 nm, the number density decreased from 5.77 × 10{sup 22} m{sup −3} to 3.68 × 10{sup 22} m{sup −3} after Sc addition. On the contrary, when samples were aged at 200 °C for 8 h, the length decreased from 59.89 nm to 43.32 nm and number density increased from 2.13 × 10{sup 22} m{sup −3} to 3.00 × 10{sup 22} m{sup −3} by adding trace Sc. Slight deterioration of tensile strength and yield strength with higher ductility was founded at the aging temperature of 175 °C for 8 h due to the larger size and lower number density of T{sub 1} precipitates along with the formation of a W (AlCuSc) phase during the casting or homogenization processes. When aging temperature increased to 200 °C, tensile strength and yield strength were significantly improved by Sc addition without losing ductility. Highly dense fine T{sub 1} precipitates take responsible for the strength improvement, and to some extent it compensated the strength loss caused by the formation of W phase. A “vacancy-prison” mechanism was adopted to explain the effect of Sc additions on the precipitation of T{sub 1} phase as a function of aging temperature.

36 MATERIALS SCIENCE↗

Enhanced strength and toughness in ultra-fine grained 99.9% copper obtained by cryo-hydrostatic extrusion

Highlights: • Cryo-HE can increase the yield strength of Cu by more than threefold. • In cryo-HE of Cu, the grain refinement is stronger by 30% than in room-HE. • Cryo-HE with post-annealing effectively creates a bimodal microstructure in Cu. • Short-term post-annealing applied to cryo-HE-treated Cu can double its ductility. • Grain refinement with recrystallization results in a slight increase of Cu toughness. - Abstract: Ultrafine grained 99.9% Cu with enhanced strength and toughness was produced by hydrostatic extrusion conducted at the temperature of liquid nitrogen. The cryo-extruded Cu has a tensile yield strength of 490 MPa, hardness of 145 HV0.2, and tensile fracture toughness of 39.5 MPa m{sup 1/2}, which means that their values increased by 380%, 185% and ~10%, respectively, compared to those of the starting material. The significant strengthening is due to the strong grain refinement to 320 nm and the high energy of defects stored during the processing at liquid nitrogen temperature. The short term post deformation annealing doubles the ductility of material even by above 10% of the elongation to fracture at a slight expense of the yield strength (485 MPa). The observed behavior of Cu can be explained in terms of its low stacking fault energy, the susceptibility to dynamic recrystallization within the working zone of the extrusion die, and the triaxial strain components with the very large strain gradients, combined with the significant adiabatic heating effect active during the hydrostatic extrusion. The better homogeneity of the grain refinement and the higher efficiency of the distribution of defects and of the energy storage accompanied by the decreased dislocation mobility during the cryo hydrostatic extrusion contributed to the higher strength.

36 MATERIALS SCIENCE↗

Influence of duplex ageing on secondary α precipitates and mechanical properties of the near β-Ti alloy Ti-55531

Highlights: • High strength β-Ti alloys are widely used for their excellent properties. • To reach an excellent combination of strength and ductility, it is attractive to explore the right heat treatment system. • While compared to the conventional single-step ageing process, duplex ageing could change the development and refinement of secondary α precipitations in near/metastable β-Ti alloys resulting varying in performance. • Therefore it is of scientific significance and engineering value to understand the influence of duplex ageing on the formation of secondary α precipitates and mechanical properties for this type of alloy. - Abstract: This paper presents the results of studies on the microstructure and mechanical properties of a near β-Ti alloy processed with different ageing approaches. Influences of intragranular ultrafine α precipitates and grain boundary α layer on mechanical properties in Ti-55531 alloy were analyzed. The results indicate that the precipitation microstructure of the duplex aged alloy exhibits a uniform size and acicular α precipitated orientation shows an angle of approximately 60°. While the morphology of secondary α precipitates in single-step aged samples appear the irregular distribution and heterogeneous size. With the final ageing time increasing, the morphology of intragranular α precipitates and grain boundary α phase brings out a distinct coarsening. The single-step aged alloy can yield a better combination of the ultimate tensile strength (1265 MPa) and ductility (9%). However, the ultimate tensile strength of the duplex aged alloy even reaches 1368 MPa but it breaks at the stage of elastic deformation. The fracture mode of Ti-55531 alloy changes from predominantly dimple fracture in single-step aged samples to predominantly faceted and cleavage type fracture in duplex aged samples causing by the differences of intragranular α precipitates and the interface between grain boundary α layer and intragranular microstructure.

36 MATERIALS SCIENCE↗

Effects of initial microstructures on serrated flow features and fracture mechanisms of a nickel-based superalloy

Highlights: • Uniaxial tensile tests are performed on a nickel-based superalloy at 473 K–973 K and low strain rates. • Effects of initial microstructures on serrated flow features, and fracture characteristics are analyzed. • The dislocation across slip in the matrix is responsible for the serrated flow. • Nucleation and growth of micro-voids is the main fracture mechanism of ST and HS superalloys. • The better tensile ductility is obtained with raising the deformation temperatures for the SAT superalloy. - Abstract: The uniaxial tensile experiments are performed on a nickel-based superalloy with different initial microstructures at intermediate temperatures (473–973) K and low strain rates (0.0001–0.001) s{sup −1}. Effects of initial microstructures on plastic deformation mechanisms, serrated flow features, and fracture characteristics are analyzed. It is clearly demonstrated that the plastic deformation mechanism of serrated flow is irrelevant to the initial microstructures, and the dislocation across slip in the matrix is responsible for the serrated flow. However, the effects of initial microstructures on fracture mechanisms are obvious, i.e., the main fracture mechanism of the ST (solution treated) and HS (solution plus γ′/γ″ phases aging precipitation) superalloys are the nucleation and growth of micro-voids, which accelerates the break of carbides and interfacial failure of carbides/matrix. While for the SAT (solution plus δ phases aging precipitation) superalloy, δ phases and carbides play a significant role in the nucleation of micro-voids. Furthermore, the increase of the deformation temperature reduces the elongation to fracture of the ST and HS superalloys. However, the better tensile ductility is obtained with raising the deformation temperatures for the SAT superalloy.

36 MATERIALS SCIENCE↗

High elongation achieved by band-like distribution of reinforcements in aluminum matrix composites

Highlights: • The high elongation of composites with high reinforcement content has been achieved by band-like distribution of ABO. • The band-like distribution of ABO could lead to more homogenous strain distribution by scattering the damages. • The cracks played a key role in the strain non-localization process, but have negligible contribution to the tensile strain. • A model of the relationship between the ductility enhancement and the band-like distribution of ABO was established. • The residual stresses induced by band-like distribution of ABO were theoretically calculated and experimentally measured. - Abstract: Ductile aluminum matrix composites reinforced by Al{sub 18}B{sub 4}O{sub 33} whisker (ABO) with band-like distribution (Band-like Aluminum Matrix Composites, BAMCs) were fabricated by powder metallurgy and extrusion followed by annealing. The cracks tend to nucleate in the ABO-rich bands, but the band-like structure induces compressive residual stress then suppresses the crack propagation and improves the strain transferring ability in the BAMCs. The denser and smaller cracks formed in the BAMCs with higher ABO volume fraction during tensile test. These cracks play an important role in the strain non-localization process, but have negligible contribution to the tensile strain.

36 MATERIALS SCIENCE↗

Face-centered titanium induced by ultrasonic surface rolling process in Ti-6Al-4V alloy and its tensile behavior

Highlights: • A gradient nanostructure of fcc-Ti is formed from a depth of 440 μm to top surface. • The influence factor of hcp to fcc phase transformation is demonstrated. • The fcc phase induced by USRP decreases the yield strength of Ti-6Al-4V alloy. • The fcc phase improves combining good strength and ductility. - Abstract: The phase transformation of face-centered cubic (fcc) titanium (Ti), transformed from hexagonal close-packed (hcp) Ti, in Ti-6Al-4V alloy subjected to ultrasonic surface rolling process (USRP) and the tensile behavior were investigated. A gradient nanostructure of fcc-Ti was formed from the depth of 440 μm to the top surface. The stress concentration at the phase interface of α phase and β phase promoted hcp to fcc phase transformation in low strain and strain rate region (adjacent to the substrate) while the extremely high strain and strain rate induced this phase transformation in the surface to sub-surface regions. USRP increased the tensile strength of Ti-6Al-4V alloy slightly but decreased the yield strength dramatically, and kept a good combination strength and ductility of Ti-6Al-4V alloy mainly due to the formation of the gradient nanostructure surface layer and hcp to fcc phase transformation.

36 MATERIALS SCIENCE↗

Changing the solidification sequence and the morphology of iron-containing intermetallic phases in AA6061 aluminum alloy processed by spray forming

Highlights: • Spray forming alters the solidification path of the Fe contaminated AA 6061 alloy. • Thus forming primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} with polyhedral morphology • Thus preventing the formation of AlFeSi with deleterious morphology • Despite Fe contamination final microstructure presented important ductility. - Abstract: Typically, aluminum alloys are contaminated by iron during recycling cycles. Such a procedure leads to the formation of intermetallic phases with detrimental morphology, which acts as stress risers, impairing mechanical properties and consequently hindering further mechanical processing and restricting recycling. This paper aimed at studying the solidification of an AA6061 alloy highly contaminated with iron (1.4 wt%). Spray forming processing allowed altering the solidification path of the Fe-modified AA 6061 alloy, resulting in the formation of primary α-Al{sub 15}(Fe, Mn){sub 3}Si{sub 2} phase with polyhedral morphology, which traps Fe and Si at elevated temperature. Furthermore, spray forming prevented the formation of intermetallic AlFeSi phases with platelet-like morphology, such as β-AlFeSi as well as the typical Chinese script morphology, resulting in a final ductile microstructure, allowing further processing by hot extrusion.

36 MATERIALS SCIENCE↗

Effect of niobium interlayer in dissimilar friction stir welding of aluminum to titanium

Highlights: • In the present study, FSW of Al to Ti with Nb interlayer has been characterized. • Fragmentation and distribution of Nb and Ti have been correlated with properties. • Ternary mixing and chemical reaction reduced the brittleness of the joint. • Al in the weld nugget showed a gradient in microstructural features. • The weld with Nb interlayer exhibited higher ductility. - Abstract: The most important issue associated with dissimilar welding is the formation of detrimental intermetallics and consequent reduction in mechanical properties of the weld. It was expected that addition of an interlayer would modify the pattern of the intermetallic formation. The present investigation deals with Friction Stir Welding of aluminum (Al) to titanium (Ti) in presence of niobium (Nb) interlayer. X-ray Computed Tomography results highlighted that fine particles of both Ti and Nb are homogeneously distributed. Large Ti particles are substantially fragmented whereas large Nb particles remain as flakes. Microstructural features of the nugget zone indicated a complex mixing of materials. Jointing had been perceived through elemental diffusion at the interfaces of Al/Ti and Ti/Nb. However, Nb restricted the reaction between Al and Ti, and acted as an efficient interlayer to retard the formation of brittle Al{sub 3}Ti intermetallic phase. Mechanisms of microstructural evolution in Al side of the weld have been identified as Dynamic Recovery, Dynamic Recrystallization and particle stimulated nucleation. Significant improvement in the tensile ductility had been observed due to the presence of finer particles. The presence of Nb in the weld nugget influences the microstructural evolution and tensile properties of the weld by reducing the formation of intermetallics.

36 MATERIALS SCIENCE↗