Search NASA⌕ Search

SEARCH · Search NASA

Results for “Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Comparison of Signal Response Between EDM Notch and Cracks in Eddy-Current Testing

In the field of ET an eddy-current instrument is calibrated on a manufactured notch that is designed to simulate a defect in a part. The calibrated instrument is then used to scan parts with the assumption that any response that is over half the amplitude of the notch signal is taken to be defective. The purpose of this study is to attempt a direct comparison of the signal response observed from an EDM notch to a crack of the same size. To make this comparison test equipment will be set up and calibrated as per normal inspection procedures. Once this has been achieved both notches and as many different sizes of crack specimens will be scanned and the data recorded. This data will then be analyzed to provide a comparison of the response. The results should also provide information that shows it is acceptable to use the half-amplitude method for determining if a part is defective. The tests will be performed on two different materials commonly inspected, titanium and aluminum. This will allow a comparison of the results between materials.

Kane, Mary↗

Insulation Resistance and Leakage Currents in Low-Voltage Ceramic Capacitors with Cracks

Measurement of insulation resistance (IR) in multilayer ceramic capacitors (MLCCs) is considered a screening technique that ensures the dielectric is defect-free. This work analyzes the effectiveness of this technique for revealing cracks in ceramic capacitors. It is shown that absorption currents prevail over the intrinsic leakage currents during standard IR measurements at room temperature. Absorption currents, and consequently IR, have a weak temperature dependence, increase linearly with voltage (before saturation), and are not sensitive to the presence of mechanical defects. In contrary, intrinsic leakage currents increase super-linearly with voltage and exponentially with temperature (activation energy is in the range from 0.6 eV to 1.1 eV). Leakage currents associated with the presence of cracks have a weaker dependence on temperature and voltage compared to the intrinsic leakage currents. For this reason, intrinsic leakage currents prevail at high temperatures and voltages, thus masking the presence of defects.

testing↗

Energy Analysis Method for Hidden Damage Detection

A method of detecting internal defects in composites or other multilayer materials includes generating a wavefield on a surface of the material. Wavefield data is collected from the wavefield on the surface, and the measured wavefield data is processed to provide measured energy data. The method may include generating simulated or predicted energy data for the multilayer material that is compared to the simulated energy data to determine if the multilayer material has internal defects or damage below the surface. The method can be utilized to detect and/or quantify damage or other defects that are "hidden" by damage that is closer to the surface of the material.

Campbell Leckey, Cara A.↗

Distorted Perovskites for High Voltage Dielectric Capacitors

There are several mechanisms which have been proposed for the existence of colossal dielectric constant in the class of perovskite calcium copper titanate (CaCu3Ti4O12 or CCTO) materials. Researches indicate that existence of twinning parallel to (100) (001) and (010) planes causes planar defects and causes changes in local electronic structure. This change can cause insulating barriers locally which contribute to the large dielectric values irrespective of processing. The combination of insulating barriers, defects and displacements caused by twinning have been attributed to the generation of large dielectric constant in CCTO. To examine some of these arguments some researchers replaced Ca with other elements and evaluated this concept. In this study we present the synthesis and characterization of Ga2/3Cu3Ti4O12-xNx (GCTON) material. This provides both distortion due to atomic size difference and defects due to insertion of nitrogen. The morphology of the compound was determined to show that processing has tremendous effect on the dielectric values. The resistivity of GCTON was several order higher than CCTO and dielectric constant was higher than 10,000.

Gill, Puneet↗

Machine Learning Based AFP Inspection: A Tool for Characterization and Integration

Automated Fiber Placement (AFP) has become a standard manufacturing technique in the creation of large scale composite structures due to its high production rates. However, the associated rapid layup that accompanies AFP manufacturing has a tendency to induce defects. We forward an inspection system that utilizes machine learning (ML) algorithms to locate and characterize defects from profilometry scans coupled with a data storage system and a user interface (UI) that allows for informed manufacturing. A Keyence LJ-7080 blue light profilometer is used for fast 2D height profiling. After scans are collected, they are process by ML algorithms, displayed to an operator through the UI, and stored in a database. The overall goal of the inspection system is to add an additional tool for AFP manufacturing. Traditional AFP inspection is done manually adding to manufacturing time and being subject to inspector errors or fatigue. For large parts, the inspection process can be cumbersome. The proposed inspection system has the capability of accelerating this process while still keeping a human inspector integrated and in control. This allows for the rapid capability of the automated inspection software and the robustness of a human checking for defects that the system either missed or misclassified.

Sacco, Christopher↗

In-Situ Detection of Process-Induced Porosity During Cure of Out-of-Autoclave Composites

Composite materials offer unique benefits in aerospace applications, including high strength-to-weight ratio, and are becoming increasingly used by industry manufacturers. Current manufacturing and processing methods can lead to defects in the composites, which are identified after fabrication using inspection methods. This study utilized a high-temperature ultrasonic inspection system to detect process-induced porosity in an out-of-autoclave (OOA) composite panel during cure. In order to perform ultrasonic scans in-situ during cure, the system needed to be able to operate at oven temperatures up to 200 °C. There are no commercially available ultrasonic scanning systems that can operate continuously at these temperatures, so an enclosure was fabricated to insulate the ultrasonic system in the curing oven. The enclosure housed a MISTRAS® motorized X-Y raster scanner and contact transducer (Olympus® X2002). The Olympus® X2002 contact transducer is a continuous high-temperature delay line transducer with a center frequency of 2.25 MHz. In order to prevent the inside of the enclosure from reaching high temperatures, a sparge pipe inside the cooling enclosure was connected to a liquid nitrogen (LN2) tank outside of the oven via insulated hoses. The cooling system was automatically controlled by a temperature controller that was programmed to open a solenoid valve along the hose at 31 ℃ and close at 28 ℃ inside the cooling enclosure. When the solenoid valve was open, LN2 would flow from the LN2 tank and vaporize prior to reaching cooling enclosure. A U-shaped sparge pipe had holes drilled along its length to uniformly introduce cold nitrogen gas into the cooling enclosure. This prevented the motors from ever reaching the maximum desired operating temperature of 38 ℃. In the bottom of the enclosure, the tool plate was placed with the composite facing the outside of the enclosure, exposing it to the temperatures of the oven. The tool plate was 63.5 mm thick borosilicate glass, which was chosen for its low ultrasonic attenuation and moderate thermal conductivity. A thin layer of ultrasonic couplant was placed on the tool plate. The transducer sent and received ultrasonic waves through the tool plate into the composite. A MISTRAS® Remote UT System performed all wave generation, analog to digital conversion, and data acquisition and processing. The transducer was connected directly to the Remote UT System via a high-temperature BNC cable (CD International, RG-316). Polyimide insulated copper wire was used to connect the scanner to a 2-axis motor drive, which was connected to the Remote UT System. The motor drive and Remote UT System were located outside the industrial oven. A diagram of the ultrasonic system is shown in Figure 1. Figure 1: Diagram of ultrasonic in-situ defect detection system. In this study, a porosity gradient was introduced into the carbon fiber reinforced polymer (CFRP) composite through a misfit of the part and caul plate. A 24-ply quasi-isotropic ([0/90, ±45]12S) composite panel was laid up using Newport® AS4C-M/NB321 out-of-autoclave (OOA) plain weave (PW) prepreg (42% resin content, 195 g/m2). The first 16 plies were 203 mm × 203 mm. Ply drops were incorporated into the panel by decreasing the length of plies 17-24. The sizes of each ply are included in Table 1. All plies were centered along their length (x-axis) creating a trapezoidal type cross-section. Table 1: Ply sizes Plies Length (mm) Width (mm) 1-16 203 203 17-18 102 203 19-20 85 203 21-22 68 203 23-24 51 203 A 15-5 stainless steel caul plate (Size: 203 × 203 × 1.2 mm) was placed on the laminate. The composite and caul plate were vacuum bagged to the tool plate. Per the product datasheet, Newport 321 can be cured between 121 °C and 149 °C, depending on service temperature, with a hold for 90-120 minutes. Based on prior thermal testing of the cooling enclosure, the desired composite temperature cycle could be attained when the air temperature of the oven was ramped to 160 °C at a rate of 1.7 °C/min with a 3 hour hold. The extended hold was not necessary to cure the composite, but did allow for additional scans at the cure temperature during preliminary testing. The composite panel was under vacuum pressure for the entire cure cycle. Under vacuum, the caul plate deformed causing high and low pressure regions. The low-pressure regions formed high porosity in the composite part. The ultrasonic data collected showed that the inspection system was able to monitor the evolution of porosity within the composite throughout the cure cycle. Fifty scans of a 203 mm × 51 mm (8 in. × 2 in.) area of the composite were completed throughout the cure cycle. The scan speed was set to 43 mm/s in the x-direction and 36 mm/s in the y-direction, with a 1.0 mm/pixel resolution in both directions. Each scan took approximately five minutes to complete. Figure 2 shows C-scan amplitude data (top view) from one scan during the cure cycle. The color map indicates the maximum amplitude (%) measured with a time gate that contains reflections from the back surface (furthest from the transducer in contact with the caul plate) of the composite. Because porosity in the composite increases the ultrasonic attenuation in the composite part, a higher amplitude (red) indicates low porosity and a lower amplitude (blue) indicates high porosity. The regions where the caul plate was applying increased pressure (center and ends of the panel) resulted in reduced porosity, whereas the ply drop regions had reduced pressure and thus had higher porosity. Figure 2: Amplitude C-scan (top view) of OOA composite from one scan during the 160 °C temperature hold. Higher amplitude (red) indicates low porosity. Lower amplitude (blue) indicates high porosity. A B-scan is a two-dimensional image plotting the ultrasonic signals from a single y-position at every x-location of the composite panel. The travel time (μs) of the ultrasonic wave (representing the through-thickness location) is plotted along the y-axis, and the ultrasonic wave signal is represented as a contour map. Based on the B-scan data, the location of the defects with respect to the composite thickness was able to be determined. The ply drop regions had high porosity near the front (tool plate) surface of the composite (Figure 3). Figure 3: B-scan (cross-section view) of OOA composite from one scan during the 160 °C temperature hold. Using the data obtained from amplitude C-scans and B-scans throughout the cure cycle, the high and low porosity regions within the composite laminate were detected and localized with high spatial resolution. This paper will discuss the evolution of porosity content in the OOA composite during cure. OOA tests aided the transition of this system to an autoclave, which is the primary method of curing aerospace-grade thermoset composites.

Tyler B. Hudson↗

Proof Testing Aluminum and Titanium Thin-Walled Tubes for Aerospace Applications

Proof testing aerospace components aids in verifying the structural integrity of flight hardware. This process is often an important step in the certification process for critical parts. Though proof testing is a common practice at NASA and in industry, there is often a need to understand better the effectiveness of proof testing pressure systems discovering cracklike flaws or defects. Often proof tests are used in requirements and in practice as technical rationale for screening critical defects in a part in lieu of performing a non-destructive inspection. The intent of this work is to define proof test failure envelopes for thin-walled tubes composed of two materials: aluminum and titanium. Both materials are common in aerospace thin-walled tubing applications which is why these were the materials chosen for this study. The fracture mechanics software NASGRO was used to perform a parametric study on the effect of defects in thin-walled tubes subjected to proof testing. For both materials, the parameters varied in the NASGRO analyses were aspect ratio, proof test pressure, thickness, diameter, and flaw multiplier. With each case defined as a through crack or failure, the results were then pulled into MATLAB in order to parse through the data and produce failure envelope plots. Failure envelopes were created by meshing a surface in between the minimum proof pressure failing data points. As expected, based on material properties, the plots indicated the aluminum material would fail at much lower proof tests than the titanium. The parametric data and failure envelopes may be used as general qualitative insight on the effectiveness of proof testing thin-walled tubes of similar alloys.

Leah B Davis↗

Mining the Gravity Mutants of Arabidopsis

Gravity mutants are a valuable resource for understanding gravity perception, signaling, and response in plants. A review of 190 publications resulted in a list of 97 loci with mutations that caused a gravitropic phenotype. While all these mutants show some form of gravity phenotype, several are also generally defective in growth. After removing these nonspecific mutants, 76 loci were deemed to have true gravity mutants. The gene list was then used to create a sortable database containing key factors of gravity signaling as well as data on methodologies and the development of mutant lines. Indexing this database has allowed us to pull out trends that were not visible in individual publications. For example, mutants that are unable to rearrange starch statoliths make up a larger proportion of the described inflorescence stems mutants than any other organ. Comparing these statolith mutants across organs shows that root and inflorescence stems consistently display different phenotypes for the same class of defect. The more severe gravity defects are most commonly described in root tissue while other tissues are more likely to show only a delayed or reduced response to gravity. The experience of members of the GeneLab plant Analytics Working Group (AWG) in data visualization and gene mapping have sparked new ideas for utilizing this database. Knowledge of shared traits, mutant development, and growth can provide a new resource for the production of seed lines specialized for their response to gravity.

gravitropism↗

Investigate the height dependency of the micro-/defect-structure and mechanical properties of additively manufactured AlF357 aluminum alloy

When the laser powder bed fusion (L-PBF) additive manufacturing method is employed to build parts with increased heights, there is a possibility that defects are increased in part. This study investigates the effect of build height on the micro-/defect-structure and, consequently, the mechanical properties of L-PBF AlF357, an Al-Si-Mg alloy family. Tall vertical cylinders of 316 mm with 15 mm diameter were fabricated and cut into specimens at different heights. Although not much difference is observed in the microstructure (grain size and morphology), the defects' size and population slightly vary with height. Nonetheless, the tensile properties of the L-PBF AlF357 are found to be independent of height. This is ascribed to the approximately identical microstructure and marginal difference in the defect's size and distribution along the heights.

Laser powder bed fusion (L-PBF)↗

Molecular dynamics simulation of effects of solutes on dislocation propagation in Ni-based superalloys

Ni-based superalloys are used in the hot sections of jet turbine engines because of their high strength, stability and resistance to oxidation. The properties of these alloys can be further optimized by adding alloying elements. Therefore, a fundamental knowledge on the effect of different elements on properties of Ni-based superalloys is required. Molecular dynamics simulation could shed light here but its application is hindered by the absence of reliable and computationally cheap semi-empirical potential of the interatomic interaction for 4 and more element alloys. We will present a new Ni-Al-Cr-Nb Finnis-Sinclair (FS) potential specially designed to simulate the dislocation propagation from to  phase. In order to construct this potential, we designed a special algorithm to incorporate the data on element partitioning in the potential development procedure. For example, it is known from experiment, that Cr is mostly present in the gamma phase. Figure 1 shows a snapshot obtained after equilibration of the model of the Ni68Al17Cr15 alloy at T=1000 K using the hybrid Monte-Carlo (MC)/molecular dynamics (MD) simulation with the developed semi-empirical potential. One can clearly see that the Cr partitioning is in agreement with the experimental data. We will discuss the developed algorithm to incorporate the solute partition data in details. Using the developed semi-empirical potential, we first investigated the effect of anti-site defects in the  phase on the single dislocation propagation. It was found that the dislocation velocity increases with the increasing of the anti-site defect concentration. This effect was attributed to smaller number of Al-Al pairs forming during the dislocation migration in the presence of the anti-site defects. Next, we investigated the effect of Nb on the dislocation pair propagation in the Kolbe mechanism. It was found that the addition of Nb leads to considerable decrease in the dislocation propagation rate. This is in agreement with the experimental data on the effect of Nb on the creep resistance of the Ni-based superalloys. We will discuss the origin of this effect.

Mikhail I. Mendelev↗

Maize Rough Endosperm6 (rgh6) Encodes A Predicted Dead-Box RNA Helicase and Affects Mirna Processing in Endosperm Development

Maize rough endosperm (rgh) mutants have defective kernels with a rough, etched, or pitted endosperm surface. Molecular genetic analysis of this mutant class has identified multiple RNA processing proteins critical to endosperm development. Here, we report on the developmental and molecular function of the rgh6 locus. The rgh6 mutant was isolated from the UniformMu transposon tagging population. Mutant kernels have reduced endosperm size and defective embryos that develop in a more apical position than typical for defective embryos. TB translocation crosses revealed that rgh6 mutant endosperm inhibits normal embryo development. Positional cloning of the rgh6 locus found that it encodes a predicted DEAD-box RNA helicase. Consistent with a predicted function for RNA processing, transient expression of a RGH6-GFP fusion protein is localized to nucleolus and nuclear speckles in Nicotiana benthamiana leaves. Rgh6 transcripts are highly expressed in endosperm epidermal cell types such as the aleurone, basal endosperm cell layer, embryo surrounding region, and endosperm adjacent to scutellum. Markers of these cell types show increased levels in rgh6 mutant kernels. Mutant endosperm tissues have increased precursor microRNA (pre-miRNA) and decreased mature miRNA relative to normal sibling endosperm, indicating that rgh6 is required for miRNA processing. The transcript levels for most miRNA target genes accumulate to a higher level in rgh6 mutant tissue. These results suggest that miRNA processing and regulation of miRNA target genes are required for normal endosperm development.

Plant Sciences↗

Enhanced Quantification of 3D Woven Composites Via Fourier Analysis and Structure Tensors Applied to CT Scans

NASA's development of advanced 3D woven carbon composites, such as HEEET and 3MDCP, represents a significant leap in materials designed to endure extreme atmospheric entry conditions. However, the internal complexity of these materials introduces a variety of structures and novel defect types. Traditional characterization methods rely on labor-intensive, manual examination of X-ray CT scans, demanding considerable time and expertise. This process, while thorough, is not sustainable for large-scale analysis and defect tracking. Addressing this critical challenge, this presentation introduces an innovative suite of automated tools and analytical techniques, pioneered by the Mars Sample Return (MSR) Earth Entry System (EES) Thermal Protection System (TPS) project. These advancements offer a more efficient and accurate approach for quantifying CT data and characterizing the defects of 3D woven composites.

Magnus Haw↗

Quantitative Characterization of 3D Woven Composites Via Fourier Analysis and Structure Tensors Applied to CT Scans

NASA's development of advanced 3D woven carbon composites, such as HEEET and 3MDCP, represents a significant leap in materials designed to endure extreme atmospheric entry conditions. However, the internal complexity of these materials introduces a variety of structures and novel defect types. Traditional characterization methods rely on labor-intensive, manual examination of X-ray CT scans, demanding considerable time and expertise. This process, while thorough, is not sustainable for large-scale analysis and defect tracking. Addressing this critical challenge, this presentation introduces an innovative suite of automated tools and analytical techniques, pioneered by the Mars Sample Return (MSR) Earth Entry System (EES) Thermal Protection System (TPS) project. These advancements offer a more efficient and accurate approach for quantifying CT data and characterizing the defects of 3D woven composites.

3D Woven↗

Stress-Activated Positive Holes (O− in a Matrix of O2–) Cause DNA Damage in Surface-Dwelling Organisms: Unveiling Mutation-Induced Secrets of Nature

Peroxy defects consist of pairs of tightly bonded oxygen anions in the –1 valence state such as in O3X/OO\YO3 with X, Y = Si4+, Al3+ etc. They commonly occur in igneous, metamorphic and many sedimentary rocks. When such rocks are stressed by tectonic forces, peroxy defects break up, releasing highly mobile electronic charge carriers: defect electrons in the O2– sublattice, i.e. unbound O–, known as “positive holes”, h•. The h• can flow out of stressed rock volumes, spreading far and wide, causing electric currents and electrochemical reactions. This study explores how the h• impact the electron flow in the electron transport chain (ETC) of organisms on the surface of rocks such as gabbro and granite. We found that, by forming hydroxyl radicals and superoxide anions, the h• disrupt the in vivo coordination of reduction-oxidation reactions that are essential for the timing of the redox cycle. Our observations show that stress activation of h• delays the sprouting of certain plant seeds and impedes the growth of yeast cultures, Saccharomyces cerevisiae. The h• induce mutations and affect plant development as evidenced by reduced stem length and leaf size. At the same time, the h• serve as a source of abiotic oxidation, capable of forming various organic compounds in situ. Through the generation of radical species that create new carbon-carbon bonds the h• facilitate the abiotic synthesis of hydrocarbons and other organic molecules essential to life, including porphyrins. Our findings highlight the intricate interplay between positive holes, redox timing, and biological processes, revealing their significant role in influencing the growth and development of organisms in tectonically stressed crustal environments. Understanding these effects enhances our broader comprehension of redox biology and the influence of environmental factors on cellular development in natural settings.

astrobiology↗

Swift Mission Gyro Patch and Re-Calibration Without A Calibration Campaign

The Swift spacecraft has three Two-Axis-Rate-Assemblies (TARAs) (designated as TARA 1, TARA 2, and TARA 3, and generically referred to as gyros) which until March of 2024 were all used in rate estimation as an operational workaround (dubbed “corrector-gyro”) of a software defect discovered in 2007. TARA 1 performance degraded throughout 2023 and 2024, making it an unreliable rate source. It was determined that shifting TARA 1 to be the corrector-gyro and using mainly TARAs 2 and 3, with the existing flight software (FSW) defect, would not meet performance requirements for science operations. Rather the FSW was patched to remove the defect found in 2007. This patch was delivered by the vendor in 2009, but was not fully tested or installed at that time. A decision was made in 2024 to install the patch despite limited simulation and testing capabilities. The problem facing the team was to come up with a set of alignment parameters that would work with the new patch, using data from the spacecraft operating normally in the old configuration. Calibration activities would have been possible in either the old or new FSW configuration, but were ultimately deemed unnecessary, saving staff time and pre-serving time on the spacecraft for science data collection. This paper describes the old and new FSW configurations related to gyro processing and alignment, and how the raw gyro and star tracker data from normal operation were used with a multidimensional unconstrained nonlinear minimization in MATLAB (Nelder-Mead1) to produce a fully calibrated set of gyro alignment parameters compatible with the patched FSW. Flight data is presented showing that not only did the process work, it improved performance significantly, rivaling the best slew performance of the mission to date.

MATLAB↗

Real-Time Temperature Field State Observer and Digital Replica to Support Cyber-Physical Testing

Cyber-physical testing is a class of experimental methods in which a system is partitioned into physical and numerical components to study its overall behavior. Transfer systems are typically needed to capture relevant interactions by enforcing appropriate interface conditions between the physical and numerical portions. While cyber-physical testing is often performed using lumped-parameter systems, thermomechanical cyber-physical testing requires the use of thermal actuators as transfer systems to apply a thermal condition over a spatially distributed region or surface. Thus, the interactions between the numerical and physical components are of a distributed nature, i.e., a field rather than point values. In this paper, we develop and experimentally validate a state observer for temperature fields to enable thermomechanical cyber-physical testing. The state observer provides continuous estimates of temperature over a surface of the thermal actuator using only temperature measurements at discrete locations. The estimated temperature field is then leveraged to account for localized mechanical defects in the interface condition. The method consists of building a digital replica of one portion of the control plant. By imposing defects in the digital replica it is used to generate and output the response of a thermal load pattern that represents that of a physical system with mechanical defects.

Manuel Salmeron↗

AC and DC Fault Management for Megawatt Electrified Aircraft Electrical Powertrains Task 3: Lifetime and Reliability of Electrical Insulators

This research project was a collaborative investigation between researchers at the RTX Technology Research Center (RTRC) and the University of Texas at Austin and made a significant contribution to enabling electric aircraft. The transport of electric power between the points of generation and use requires power cables. These cables must be smaller, lighter and provide a more predictable life than power cables used in stationary applications. Consequently, this investigation provided heretofore unavailable information supporting the safety and reliability of smaller lighter power cables for electrified aircraft. In addition, the research identified key additional engineering data needed to support quantitative reliability assessments. Important advances included: • Demonstrated that at least one manufacturer can make a novel, smaller, lighter power cable that is free from serious defects. • Developed and published an appropriate analytical construct to describe the life of this novel cable. This is a necessary step for use in aviation where the understanding of remaining life is critical. • Demonstrated thermal-mechanical aging that suggested 1000+ flights before the thermal-mechanical processes produced defects large enough that the defect growth was accelerated electrically. • Showed that electrical aging took place at two rates. The first possibly lasting weeks to months and the second possibly days to weeks. If robust, this provides a good diagnostic for cable replacement. • Demonstrated that the traditional electrical testing of cable materials using manufactured voids can be misleading due to the size of the voids. Emerging laser drilling technology permitted demonstration that the physics of failure in realistically small voids is different from that in the unrealistically large voids used in earlier research, which is very important for high-quality, high-performance, small aircraft cables. Although this project represents a significant contribution to the specifics of cable aging in the aircraft environment, important additional research remains to be completed, including: • Non-uniform thermal cycling by applying the heat from the center conductor to maximize thermal stress next to the core area where the electric gradient is the strongest. This builds on the uniform thermal cycling that has been completed. • The augmentation of the thermal-mechanical failure rate by electrical processes. Better understanding of these time constants strongly affects the ability to predict life. • Termination design: Terminations provide not only electrical reflection potential, but a location for a series arc fault and an area where ozone can diffuse into the center conductor and negatively affect cable insulation. • The abrasion and ozone resistance of the cable jacket. • Pressure cycling as an accelerant of thermal, mechanical, and/or electrical aging. • Possible methods for online PD detection and offline PD localization

model↗

Structural Integrity Evaluation of the Lear Fan 2100 Aircraft

An in-situ nondestructive inspection was conducted to detect manufacturing and assembly induced defects in the upper two wing surfaces (skin s) and upper fuselage skin of the Lear Fan 2100 aircraft E009. The effects of the defects, detected during the inspection, on the integrity of the structure was analytically evaluated. A systematic evaluation was also conducted to determine the damage tolerance capability of the upper wing skin against impact threats and assembly induced damage. The upper wing skin was divided into small regions for damage tolerance evaluations. Structural reliability, margin of safety, allowable strains, and allowable damage size were computed. The results indicated that the impact damage threat imposed on composite military aircraft structures is too severe for the Lear Fan 2100 upper wing skin. However, the structural integrity is not significantly degraded by the assembly induced damage for properly assembled structures, such as the E009 aircraft.

Composites↗