Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electronic Conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Role of calcination atmosphere in vanadium doped Li{sub 4}Ti{sub 5}O{sub 12} for lithium ion battery anode material

Highlights: • First comparison on V doped Li{sub 4}Ti{sub 5}O{sub 12} (VLTO) synthesized in air and argon. • Ti{sup 4+} do not reduce to Ti{sup 3+} in air calcined VLTO. • V doping enhances reducing of Ti{sup 4+} to Ti{sup 3+} in argon calcined VLTO. • Li{sub 4}Ti{sub 4.9}V{sub 0.1}O{sub 12} calcined in argon shows best charge-discharge behaviors. • Conductivity enhancement in argon calcined VLTO upto three orders. - Abstract: Li{sub 4}Ti{sub 5}O{sub 12} (LTO) with enhanced properties can replace the conventional carbonaceous anode material of lithium ion battery. Vanadium doped LTO (Li{sub 4}Ti{sub 5-x}V{sub x}O{sub 12}, x = 0, 0.05, 0.1, 0.15) materials are synthesized by sol-gel process followed by calcination of dried gel in air and argon atmosphere. No additional phase corresponding V is indicated in XRD patterns. Calcination in argon reduces the particle size of Li{sub 4}Ti{sub 5-x}V{sub x}O{sub 12} while V doping reduces particle size distribution. XPS reveals that Ti{sup 4+} get reduced to Ti{sup 3+} only in argon calcined Li{sub 4}Ti{sub 5-x}V{sub x}O{sub 12} which is enhanced by V doping. Electrochemical impedance spectroscopy confirms that compared to LTO, lithium ion diffusion coefficient of air and argon calcined Li{sub 4}Ti{sub 4.85}V{sub 0.15}O{sub 12} is approximately two and three times higher. Argon calcined Li{sub 4}Ti{sub 4.9}V{sub 0.1}O{sub 12} shows highest charge-discharge capacities at almost all C-rates (0.1 to 5C; 1C = 175mAg{sup −1}). Electronic conductivity of argon calcined Li{sub 4}Ti{sub 4.9}V{sub 0.1}O{sub 12} is 1.7 × 10{sup −2} S cm{sup −1} which is three orders higher than that of LTO.

36 MATERIALS SCIENCE↗

Efficient Nanoporous Silicon Membranes for Integrated Microfluidic Separation and Sensing Systems

Nanoporous devices constitute emerging platforms for selective molecule separation and sensing, with great potential for high throughput and economy in manufacturing and operation. Acting as mass transfer diodes similar to a solid-state device based on electron conduction, conical pores are shown to have superior performance characteristics compared to traditional cylindrical pores. Such phenomena, however, remain to be exploited for molecular separation. Here we present performance results from silicon membranes created by a new synthesis technique based on interferometric lithography. This method creates millimeter sized planar arrays of uniformly tapered nanopores in silicon with pore diameter 100 nm or smaller, ideally-suited for integration into a multi-scale microfluidic processing system. Molecular transport properties of these devices are compared against state-of-the-art polycarbonate track etched (PCTE) membranes. Mass transfer rates of up to fifteen-fold greater than commercial sieve technology are obtained. Complementary results from molecular dynamics simulations on molecular transport are reported.

36 MATERIALS SCIENCE↗

Ionic/electronic conductivity regulation of n-type polyoxadiazole lithium sulfonate conductive polymer binders for high-performance silicon microparticle anodes

Low-cost silicon microparticles (SiMP), as a substitute for nanostructured silicon, easily suffer from cracks and fractured during the electrochemical cycle. A novel n-type conductive polymer binder with excellent electronic and ionic conductivities as well as good adhesion, has been successfully designed and applied for high-performance SiMP anodes in lithium-ion batteries to address this problem. Its unique features are attributed to the strong electron-withdrawing oxadiazole ring structure with sulfonate polar groups. The combination of rigid and flexible components in the polymer ensures its good mechanical strength and ductility, which is beneficial to suppress the expansion and contraction of SiMP s during the charge/discharge process. By fine-tuning the monomer ratio, the conjugation and sulfonation degrees of the polymer can be precisely controlled to regulate its ionic and electronic conductivities, which has been systematically analyzed with the help of an electrochemical test method, filling in the gap on the conductivity measurement of the polymer in the doping state. The experimental results indicate that the cell with the developed n-type polymer binder and SiMP (~0.5 μm) anodes achieves much better cycling performance than traditional non-conductive binders. It has been considered that the initial capacity of the SiMP anode is controlled by the synergetic effect of ionic and electronic conductivity of the binder, and the capacity retention mainly depends on its electronic conductivity when the ionic conductivity is sufficient. Here, it is worth noting that the fundamental research of this work is also applicable to other battery systems using conductive polymers in order to achieve high energy density, broadening their practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extended reaction zone of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 cathode for solid oxide fuel cell

The oxygen reduction reaction at the cathode of solid oxide fuel cell (SOFC) is a complicated process which involves the interaction of oxygen molecules, electrons, and oxygen ions. Therefore, it can only proceed at locations where gas, electronic conductor, and an oxygen ion conductor meet. Although the extension of the reaction zone beyond the traditional so-called triple-phase-boundary (TPB) is widely accepted for a mixed ionically and electronically conductive cathode, work in this area has yet to reach a consensus on how far the reaction zone can be extended. In this study, anode-supported fuel cells with a variety of LSCF cathode thicknesses were fabricated and tested in two cathode environments, flowing oxygen and flowing air. In flowing oxygen, the cell performance increased with LSCF cathode thickness over the entire range investigated (from 5 to 33 μm). In flowing air, the cell performance also increased with the LSCF cathode thickness from 5 to 13 μm, but then remained almost constant with further increase in cathode thickness. In flowing oxygen, since there was no concentration polarization related to oxygen diffusion, the polarization resistance of oxygen reduction decreased with the LSCF cathode thickness because of the increased number of reaction sites. A linear relationship was established between the reciprocal of the polarization resistance and the cathode thickness, which was explained by a model developed for aqueous gas diffusion electrodes.

30 DIRECT ENERGY CONVERSION↗

Corrosion-Resistant Non-Carbon Electrocatalyst Supports for PEFCS

Insufficient durability of commercial catalysts is a persistent issue for PEFC applications.1 Herein, Pt on Nb-doped-TiO 2 is reported as a highly durable electrocatalyst on which the direct 4-electron reduction of oxygen to water is more facile compared to Pt/C. All performance metrics are reported comparing Pt/Nb-TiO2 with a 15% Pt loading, against a commercial Pt/C catalyst (46.5% Pt loading, Tanaka, K. K.). Nb-doped-TiO 2 with high surface area and high electronic conductivity was synthesized using the supercritical fluid method. Initially, the durability of the catalyst was characterized using accelerated stability tests (ASTs) involving 10,000 high potential cycles (DOE/FCCJ protocol) and the Pt/Nb-TiO 2 was found to retain 78% of its initial electrochemically active surface area (ECSA) compared to the 57.6 % retained by Pt/C. These observations were in excellent agreement with previous reports that the Pt particle size of Pt/C grew from 2nm to 8nm during the AST protocol along with severe corrosion and amorphization of the carbon surface.2, 3 TEM and XPS studies of the Pt-Nb-doped-TiO 2 catalyst showed that the Pt particle size grew from 3nm to 6nm and the Nb(IV) and Ti(III) in the support were oxidized to Nb(V) and Ti(IV) after the durability test. Thus, the improvement in Pt/Nb-TiO 2 ECSA retention was attributed to the lower extent of particle growth and lack of oxidative support loss upon oxidation as compared to Pt/C. The oxygen reduction reaction (ORR) performance was characterized by linear polarization using a rotating disk electrode (RDE). The electrochemical surface areas of Pt/Nb-TiO 2 and Pt/C were found to be 48m2·g -1 and 83m2·g -1 respectively, and the mass activity for the ORR at 0.9V vs. RHE were found to be 150 mA·mg-1Pt and 124 mA·mg-1Pt respectively. The improved mass activity on Pt/Nb-TiO 2 was attributed to strong metal support interaction (SMSI) between the Nb-TiO 2 support and the Pt catalyst based on the 625 meV decrease in the binding energy of the Pt4f x-ray photo-electron spectroscopy (XPS) peaks of Pt/Nb-TiO 2 compared to Pt/C. To quantify the impact of the SMSI, a kinetic model was applied to calculate the elementary reaction rate constants for the various steps of the ORR on both catalysts. The reaction rate constant (k1) for the direct 4-electron transfer pathway to produce H 2 O was significantly larger in Pt/Nb-TiO 2 as compared to Pt/C. Thus, the reduction in the electron binding energy as observed in the XPS was found to aid the facile filling of the higher energy 2p orbitals of O 2 thereby leading to improved 4-electron transfer kinetics and improved overall activity.

08 HYDROGEN↗

Electron density analysis of the effects of sugars on the structure of lipid bilayers at low hydration - a preliminary study

Small angle X-ray scattering is used to study the effects of sugars on membranes during dehydration. Previous work has shown that the bilayer and chain-chain repeat spacings of DPPC bilayers are relatively unaffected by the presence of sugars. In this work we present a preliminary analysis of the electron density profiles of DPPC in the presence of sugars at low hydration. The difficulties of determining the correct phasing are discussed. Sugars and other small solutes have been shown to have an important role in improving the tolerance of a range of species to desiccation and freezing. In particular it has been shown that sugars can stabilize membranes in the fluid membrane phase during dehydration, and in the fully dehydrated state. Equivalently, at a particular hydration, the presence of sugars lowers the transition temperature between the fluid and gel phases. There are two competing models for explaining the effects of sugars on membrane phase transition temperatures. One, designated the water replacement hypothesis (WRH) states that sugars hydrogen bond to phospholipid headgroups, thus hindering the fluid-gel phase transition. One version of this model suggests that certain sugars (such as trehalose) achieve the measured effects by inserting between the phospholipid head groups. An alternative model explains the observed effects of sugars in terms of the sugars effect on the hydration repulsion that develops between opposing membranes during dehydration. The hydration repulsion leads to a lateral compressive stress in the bilayer which squeezes adjacent lipids more closely together, resulting in a transition to the gel phase. When sugars are present, their osmotic and volumetric effects reduce the hydration repulsion, reduce the compressive stress in the membranes, and therefore tend to maintain the average lateral separation between lipids. This model is called the hydration forces explanation (HFE). We recently showed that neither mono- nor di-saccharides affect the average distance between lipid chains in the bilayer, supporting the predictions of the HFE. In this paper we further investigate the effects of sugars on membrane structure by conducting electron density analysis of recent data. This preliminary analysis sheds additional light onto the effects of sugars on membrane structure.

08 HYDROGEN↗

Electronic structures and pseudogap nature of the strongly correlated Kondo semimetals and insulators CeNiSn and CeRhX(X=As, Sb)

Employing temperature (T)-dependent angle-resolved photoemission spectroscopy (ARPES) near the Ce 4d absorption edge, we have investigated the electronic structures of the strongly correlated Kondo insulators (KIs) and/or Kondo semimetals of CeNiSn and CeRhX (X=As, Sb), which also belong to potential topological KIs (TKIs). Good agreement is found between the Fermi surfaces (FSs) measured at the Ce 4d→4f on resonance and those calculated and unfolded into the Ce-only Brillouin zone, supporting the crucial Ce 4f contribution to the Fermi-edge states in them. While the FSs of CeRhSb and CeNiSn are similar to each other, they are quite different from those of CeRhAs, which is understood to originate from the semimetallic Kondo ground states of CeNiSn and CeRhSb in contrast to the insulating Kondo ground state of CeRhAs. T-dependent ARPES demonstrates the existence of the Kondo resonance above the Fermi level (EF) and its T-driven decoherence in CeNiSn and CeRhSb, and the existence of the Ce 4f Kondo-like peak well below EF with a pseudogap in CeRhAs. With increasing T, the tail of the Kondo resonance in CeNiSn and CeRhSb loses its coherence, whereas the Ce 4f Kondo-like peak in CeRhAs persists up to T≥200 K. The Kondo temperatures (TKs) are estimated via the analysis of T-dependent ARPES, yielding TK≈80 K (CeNiSn), TK≈180 K (CeRhSb), and TK≫200 K (CeRhAs). High-resolution, low-T ARPES confirms the Kondo resonance just above EF in CeNiSn and CeRhSb Kondo semimetals and the KI ground state of CeRhAs with a pseudogap of Δ≈30 meV, demonstrating the importance of the coherent Kondo states in determining their potential topological properties. The differences in the T-dependent ARPES of CeNiSn and CeRhSb suggest the weaker f-c hybridization in CeNiSn than in CeRhSb (c: conduction electron), which is likely due to the more localized Ni 3d orbitals than the delocalized Rh 4d orbitals. The differences between the T-dependent ARPES of CeNiSn/CeRhSb Kondo semimetals and those of CeRhAs Kondo insulator are likely due to the smaller volume of CeRhAs than those of CeNiSn/CeRhSb.

Kang, J-S↗

Chromium Tolerant, Highly Active and Stable Electrocatalytic Internal Surface Coating for Cathode of Commercial SOFCs (Final Report)

This project is aimed to develop a chromium (Cr) tolerant, highly active, and stable coating layer on the internal surfaces of the porous composite cathode from commercially available SOFCs. Such coating layer was developed using the additive manufacturing process of Atomic Layer Deposition (ALD) and has been applied on the cathode consisting of either an electronic conductor of LaxSr 1-x MnyO 3-δ (LSM) or mixed ionic and electronic conducting La x Sr 1-x Co y Fe 1-y O 3-δ (LSCF). PI's work has demonstrated that the internal surface of cathode from the commercial cells, can be further tailored using ALD coating to dramatically enhance the cell performance. For instance, ALD layer consisting heterostructured nano composite of nano-Pt and nano-(Mn 0.8 Co 0.2 ) 3 O 4 oxide on the internal surface of porous LSM/YSZ cathode from SOFCs, has resulted in the large reduction of the cell polarizations resistance by up to 53%, and enormous increase of power density over 370%. For the cells with LSCF/Sm 2 O 3 doped CeO 2 (SDC) cathode, the conformal layer of nano-composite consisting of superjacent CoOx and subjacent minimum amount of Pt nano-grains has resulted in the power density enhancement by 126% for the large scale industry tubular cells at 750°C, and both the performance enhancement and nanostructure of the ALD layer are stable over ~ 2000 h continuous operation performed at industry test station. In the meanwhile, those ALD coating layer developed by PI's work is also inherently Cr-tolerant, and could act as physical barrier for preventing Cr diffusion into the cathode backbone, so as to mitigate the Cr poisoning effect on the cathode. In this project, the impact of Cr on the performance of those ALD coated commercial cells has been evaluated. Based on evolution of the cell performance, the ALD coating layer chemistry and ALD coating layer thickness has been optimized to maximize the overall Cr tolerance, cell power density and cell longevity. Different ALD coating has been applied onto the internal surface of LSM/YSZ and LSCF/SDC backbone respectively. The architecture/scaffold structures on the internal surface of different cathode, designed by this project, was catalogued and analyzed using High Resolution Transmission Electron Microscopy (HRTEM), and cell power/durability performance are assured via comprehensive electrochemical performance testing in the industry operation relevant conditions. The impact of the electrochemical operation current density, the water humidity, the cell operation temperature, and cell operation duration on the Cr tolerance of ALD coated cells has been systematically investigated. There is completely different nanostructure degradation mechanisms between LSM and LSCF cells induced by Cr contamination. For the LSCF/SDC baseline cell, With the Cr source, there is no apparent Sr surface segregation phase even for the baseline cell operated for 3000 h at 750 °C. With the Cr source, there is significant amorphous (SrCr)Ox phase accumulated in the original pore region. For the commercial baseline cells, Cr contaminants on the LSM electrode severely impacted the entire cell's electrochemical performance and nanostructure degradation. Those degradations include (1). Peak power density loss of 64 % after 109 h of operation. The dramatic increase in Rp (2). They are cracking at LSM/SSZ interface, LSM grains. SSZ remains intact but with (CrMn)Ox. By contrast, ALD coating (MnCo)Ox/Pt dramatically improves the Cr resistance, as follows (1). ALD-coated cell with a power density is 280-380 % of the baseline cell, depending on the ALD layer thickness. (2). For a cell with a 20 nm thick ALD layer, there is a large performance enhancement (> 200 % power density) induced by ALD coating of Cr-tolerant Mn 0.8 Co 0.2 Ox. (3). For a cell with a 20 nm thick ALD layer, after 168 h at 750 °C power density of the ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination for 109 h. The ALD coating on the internal surface of cathode developed by this project integrated multi-functions. Those multi-functions include (1). Dramatically improving the cell power density for the commercial cells; (2). Dramatically improving contamination resistance of the cathode, for being an excellent protection coating layer sealing off Cr contamination. (3). Dramatically increasing the cell longevity by potentially preventing the microstructure evolution and grain coarsening of the cathode. Overall, this project will provide a simple solution to simultaneously enhance power density and increase the reliability, robustness, and endurance of commercial SOFCs, over the entire operating temperature range of 650-800 °C. For the inherently functional SOFC, the ALD coating of LSM based cathode mitigate the Cr-contamination. Power density of ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination. In addition to SOFCs, the novel on-demand design approach and creation of multifunctional heterogeneous architecture on the electrode surface presented in this work opens further research for their application in other types of fuel cells, batteries, and sensors for which electrochemical reactions on the surface are similarly critical.

36 MATERIALS SCIENCE↗

Review of the first charged-particle transport coefficient comparison workshop

We present the results of the first Charged-Particle Transport Coefficient Code Comparison Workshop, which was held in Albuquerque, NM October 4–6, 2016. In this first workshop, scientists from eight institutions and four countries gathered to compare calculations of transport coefficients including thermal and electrical conduction, electron–ion coupling, inter-ion diffusion, ion viscosity, and charged particle stopping powers. In this paper, we give general background on Coulomb coupling and computational expense, review where some transport coefficients appear in hydrodynamic equations, and present the submitted data. Large variations are found when either the relevant Coulomb coupling parameter is large or computational expense causes difficulties. Understanding the general accuracy and uncertainty associated with such transport coefficients is important for quantifying errors in hydrodynamic simulations of inertial confinement fusion and high-energy density experiments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of gradual cobalt substitution on lithium nickel phosphate nano-scale composites for high voltage applications

The carbon-free LiNiPO{sub 4} and cobalt doped LiNi{sub 1−x}Co{sub x}PO{sub 4}/C (x = 0.0–1.0) were synthesized and investigated for high voltage applications (> 4 V) for Li-ion batteries. Nano-scale composites were prepared by handy sol–gel approach using citric acid under slightly reductive gas atmosphere (Ar-H{sub 2}, 85:15%). Structural and morphological characteristics of the powders were revealed by X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), high resolution transmission electron microscopy (HR-TEM) and inductively coupled plasma (ICP). Except for a small impurity phase (Ni{sub 3}P), phase pure samples crystallized in the olivine-lattice structure with a linear relationship between lattice parameters (a, b and c) and chemical composition. The FE-SEM images proved that LiNiPO{sub 4}/C particles (50–80 nm) did not agglomerate, and showed that as the cobalt content was higher agglomeration had increased. The electrochemical properties of all electrodes were investigated by galvanostatic charge–discharge measurements. Substitution of Ni{sup 2} {sup +} by Co{sup 2} {sup +} caused higher electronic conductivities and showed more effective Li{sup +} ion mobility. When the cobalt content is 100%, the capacity reached to a higher level (146.2 mA h g{sup −} {sup 1}) and good capacity retention of 85.1% at the end of the 60 cycles was observed. The cycling voltammogram (CV) revealed that LiCoPO{sub 4}/C electrode improved the electrochemical properties. The Ni{sup 3} {sup +}–Ni{sup 2} {sup +} redox couple was not observed for carbon free LiNiPO{sub 4}. Nevertheless, it was observed that carbon coated LiNiPO{sub 4} sample exhibits a significant oxidation (5.26 V)–reduction (5.08 V) peaks. With this study, characteristics of the LiNi{sub 1−x}Co{sub x}PO{sub 4}/C series were deeply evaluated and discussed. - Highlights: • Structural, morphological and electrochemical effects of Co doped LiNi{sub 1−} {sub x}Co{sub x}PO{sub 4}/C electrodes are investigated. • Cheap, effective and simple sol–gel approach is used. • After the 60th cycle, capacity retention is almost 87% for LiCoPO{sub 4}/C electrode. • LiNiPO{sub 4}/C sample exhibits a distinctive oxidation (5.26 V)–reduction (5.08 V) peaks.

36 MATERIALS SCIENCE↗

Apollo Sample 64455: Petrologic and Geochemical Characterization of a Glass-Coated Impact Melt Rock

Introduction and Background: Impact melts are a key product of the impact cratering process. Impact melts can turbulently entrain pre-existing rock fragments, and melt part of those entrained materials until thermal equilibrium is achieved [1–3]. Lunar impact melt rocks are valuable for determining the precise ages of basin-forming and cratering events, which anchor the cratering chronology and dynamics of the entire solar system [4, and references therein]. Additionally, entrained clasts can inform on the petrology and age of crustal materials that predate the melt-forming impact. In lithologies where no pristine samples are available, entrained materials may hold the record of endogenous lunar volatiles, provided we can untangle their impact histories as high temperature impact melt can heat the clasts and may alter their native volatiles or isotopic signatures [5–6]. Here, we characterize an Apollo 16 sample, 64455,70B, in an effort to understand the physical, microstructural, and geochemical consequences of impact melt contact metamorphism. We acquired optical light and x-ray maps of the sample, as well as quantitative analyses via electron probe microanalysis (EPMA). These tasks allow us to better understand the interaction between impact melts and entrained clasts, ultimately closing knowledge gaps in high-temperature impact processing on planetary surfaces. Sample Description: Sample 64455 is an oblong crystalline rock encased in glass to form an egg-like shape [7–8]. The impact melt coating has altered the outer (1 to 2 mm) rind of the crystalline rock and has preserved schlieren. The interior crystalline rock is likely a crystalline impact melt rock based on its bulk Ir content of 2.25 parts per billion [9]. The composition of the impact melt glass rind cannot be solely derived from the crystalline interior, the glassy rind is more aluminous and less magnesian [10]. Neither the crystalline interior nor the glassy rind were radiometrically age dated, although several studies investigated its cosmogenic isotopes and exposure ages, which reveal the sample was exposed on the lunar surface for ~1–2 Ma [11–13]. Preliminary Results: The interior crystalline rock consists primarily of plagioclase with interstitial pyroxene and olivine. Plagioclase grains are zoned and compositions range from An97–89, while pyroxene compositions generally range from En68Fs19Wo13 to En82Fs15Wo3 and olivine are Fo77 to Fo85. Minor phases include Fe-Ni metal, Ca-phosphates, a K- and Si-rich phase, sulfides, and Fe-phosphides. The glass rind contains approximately 44 wt.% SiO2, 25 wt.% Al2O3, 6 wt.% FeO, 8 wt.% MgO, and 14 wt.% CaO, with other oxides at <1 wt.% each, although the composition of the glass becomes more variable closest to the crystalline rock. The rind consists of rounded plagioclase, pyroxene, and olivine crystals with interstitial melt. In some locations, the rounded crystals are surrounded by closely-packed, blade-like crystals, <5 µm in width. These results indicate that the crystalline interior has partially melted where in contact with the high-temperature impact melt and while further investigation is needed, pyroxene may have preferentially melted relative to olivine and plagioclase. Future Work: We plan to conduct electron backscatter diffraction (EBSD) mapping in order to determine crystallinity and crystal orientation. Next using transmission electron microscopy (TEM) data in conjunction with EBSD and EPMA information, we will model the diffusion of moderately volatile elements between the melt and remnant crystals.

A C Stadermann↗

Modeling laser interactions with aluminum and tantalum targets using a hybrid atomistic-continuum model

A hybrid atomistic-continuum method can model the microstructure evolution of metals subjected to laser irradiation. This method combines classical molecular dynamics (MD) simulations with the two-temperature model (TTM) to account for the laser energy absorption and heat diffusion behavior. Accurate prediction of the temperature evolution in the combined MD-TTM method requires reliable accuracy in electron heat capacity, electron thermal conductivity, and electron–phonon coupling factor across the temperatures generated. This study uses the electronic density of states (DOS) obtained from first-principle calculations. The calculated electron temperature-dependent parameters are used in MD-TTM simulations to study the laser metal interactions in FCC and BCC metals and the phenomenon of laser shock loading and melting. This study uses FCC Al and BCC Ta as model systems to demonstrate this capability. When subjected to short pulsed laser shocks, the dynamic failure behavior predicted using temperature-dependent parameters is compared with the experimentally reported single-crystal and nanocrystalline Al and Ta systems. The MD-TTM simulations also investigate laser ablation and melting behavior of Ta to compare with the ablation threshold reported experimentally. In conclusion, this manuscript demonstrates that integrating the temperature-dependent parameters into MD-TTM simulations leads to the accurate modeling of the laser–metal interaction and allows the prediction of the kinetics of the solid–liquid interface.

36 MATERIALS SCIENCE↗

Electrochemically Induced High Capacity Displacement Reaction of PEO/MoS2/Graphene Nanocomposites with Lithium

MoS2/PEO/graphene composite is successfully prepared and the discharge mechanism of MoS2 as an anode material for Li-ion batteries has been investigated systematically in this work. The simultaneous formation of Li2S and Mo at deep discharge depth has been shown for the first time. The deposition of Mo metal with Li residing on the defects after the first discharge increases the intrinsic electronic conductivity of the electrode leading to a superior cycling stability for over 185 cycles. After the first discharge the amorphous Mo matrix allows a large amount of Li+ ions to repeatedly deposit and being oxidized during cycling while the transition between Li2S and S contribute to the capacity above 2.0 V. The interactions between as-formed Mo and S prevents the dissolution of the intermediate polysulfide thus providing clues to immobilize the soluble species in a Li-S battery. Excellent rate performances are achieved in this MoS2/PEO/graphene composite indicating a fast diffusion path of Li+ ions existing not only in the bulk material but also in the interface between the electrode and the electrolyte.

36 MATERIALS SCIENCE↗

A High Power Density Intermediate-Temperature Solid Oxide Fuel Cell with Thin (La 0.9 Sr 0.1 ) 0.98 (Ga 0.8 Mg 0.2 )O 3-δ Electrolyte and Nano-Scale Anode

Solid oxide fuel cells (SOFCs) with thin (La0.9Sr0.1)0.98Ga0.8Mg0.2O3-δ (LSGM) electrolytes are primary candidates for achieving high (> 1 W cm-2) power density at intermediate (< 650 °C) temperatures. Although high power density LSGM-electrolyte SOFCs have been reported, it is still necessary to develop a fabrication process suitable for large-scale manufacturing and to minimize the amount of LSGM used. Here we show that SOFCs made with a novel processing method and a Sr0.8La0.2TiO3-α (SLT) oxide support can achieve high power density at intermediate temperature. The SLT support is advantageous, especially compared to LSGM supports, because of its low materials cost, electronic conductivity, and good mechanical strength. The novel process is to first co-fire the ceramic layers – porous SLT support, porous LSGM layer, and dense LSGM layer – followed by infiltration of nano-scale Ni into the porous layers. Low polarization resistance of 0.188 Ωcm2 was achieved at 650 °C for a cell with an optimized anode functional layer (AFL) and an (La,Sr)(Fe,Co)O3 cathode. Maximum power density reached 1.12 W cm-2 at 650 °C, limited primarily by cathode polarization and ohmic resistances, so there is considerable potential to further improve the power density.

36 MATERIALS SCIENCE↗

Suppressing Lithium Dendrite Growth by Metallic Coating on a Separator

Abstract Lithium (Li) metal is one of the most promising candidates for the anode in high‐energy‐density batteries. However, Li dendrite growth induces a significant safety concerns in these batteries. Here, a multifunctional separator through coating a thin electronic conductive film on one side of the conventional polymer separator facing the Li anode is proposed for the purpose of Li dendrite suppression and cycling stability improvement. The ultrathin Cu film on one side of the polyethylene support serves as an additional conducting agent to facilitate electrochemical stripping/deposition of Li metal with less accumulation of electrically isolated or “dead” Li. Furthermore, its electrically conductive nature guides the backside plating of Li metal and modulates the Li deposition morphology via dendrite merging. In addition, metallic Cu film coating can also improve thermal stability of the separator and enhance the safety of the batteries. Due to its unique beneficial features, this separator enables stable cycling of Li metal anode with enhanced Coulombic efficiency during extended cycles in Li metal batteries and increases the lifetime of Li metal anode by preventing short‐circuit failures even under extensive Li metal deposition.

Lee, Hongkyung↗

Ultrathin Lutetium Oxide Film as an Epitaxial Hole-Blocking Layer for Crystalline Bismuth Vanadate Water Splitting Photoanodes

Here a novel ultrathin lutetium oxide (Lu 2 O 3 ) interlayer is integrated with crystalline bismuth vanadate (BiVO4) thin film photoanodes to facilitate carrier transport through atomic-scale interface control. The epitaxial Lu 2 O 3 2 O 3</sub interlayer modulates the electronic conduction pathways along structural grain boundaries and determines the overall device performance. This study provides more information on the nature of interface-engineered carrier transport for efficient photoelectrode heterostructure design.

36 MATERIALS SCIENCE↗

In Situ Synthesis of Molybdenum Carbide Nanoparticles Incorporated into Laser‐Patterned Nitrogen‐Doped Carbon for Room Temperature VOC Sensing

Abstract Carbon laser‐patterning (CLaP) is emerging as a new tool for the precise and selective synthesis of functional carbon‐based materials for on‐chip applications. The aim of this work is to demonstrate the applicability of laser‐patterned nitrogen‐doped carbon (LP‐NC) for resistive gas‐sensing applications. Films of pre‐carbonized organic nanoparticles on polyethylenetherephthalate are carbonized with a CO 2 ‐laser. Upon laser‐irradiation a compositional and morphological gradient in the films is generated with a carbon content of 92% near the top surface. The specific surface areas of the LP‐NC are increased by introducing sodium iodide (NaI) as a porogen. Electronic conductivity and surface area measurements corroborate the deeper penetration of the laser‐energy into the film in the presence of NaI. Furthermore, impregnation of LP‐NC with MoC 1− x (<10 nm) nanoparticles is achieved by addition of ammonium heptamolybdate into the precursor film. The resulting doping‐sensitive nano‐grain boundaries between p‐type carbon and metallic MoC 1− x lead to an improvement of the volatile organic compounds sensing response of Δ R / R 0 = −3.7% or −0.8% for 1250 ppm acetone or 900 ppm toluene at room temperature, respectively, which is competitive with carbon‐based sensor materials. Further advances in sensitivity and in situ functionalization are expected to make CLaP a useful method for printing selective sensor arrays.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Crystallographic Insight of Reduced Lattice Volume Expansion in Mesoporous Cu 2+ -Doped TiNb 2 O 7 Microspheres during Li + Insertion

TiNb 2 O 7 represents a promising anode material for lithium-ion batteries (LIBs), but its practical applications are currently hampered by the non-negligible volumetric expansion and contraction during the charge/discharge process and the sluggish ion/electron kinetics. Here a combination technique is reported by systematically optimizing the porous and spherical morphology, crystal structure, and surface decoration of mesoporous Cu 2+ -doped TiNb 2 O 7 microspheres to enhance the electrochemical Li + storage performance and stability simultaneously. The Cu 2+ dopants preferentially replace Ti 4+ in crystal lattices, which decreases the Li + diffusion barrier and increases the electronic conductivity, as confirmed by density functional theory (DFT) calculation and demonstrated by diverse electrochemical characterizations. The successful Cu 2+ doping significantly reduces the lattice expansion coefficient from 7.26% to 4.61% after Li + insertion along the b-axis of TiNb 2 O 7 , as visualized from in situ and ex situ XRD analysis. The optimal 5% Cu 2+ -doped TiNb 2 O 7 with surface coating of N-doped carbon exhibits significantly enhanced specific capacity and rate and cyclic performances in both half- and full-cell configurations, demonstrating an excellent electrochemical behavior for fast-charging LIB applications.

36 MATERIALS SCIENCE↗