Search NASA⌕ Search

SEARCH · Search NASA

Results for “FASTENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Design and Development of Sequential Rotary Valve

Valves are used to regulate the flow of fluids through systems. This rotary valve's main purpose is to fill, pressurize, empty, and vent three smaller tanks with the supply of one larger tank. Many different designs are being taken into consideration, which are each at different stages of development. The furthest along uses three ball valves on a common shaft to open and close their respective ports as the shaft completes one full rotation or cycle. We were tasked with advancing this design to its first test as a plastic model for flow verification, as well as sizing and ordering the necessary O-rings and fasteners. A motor will also be sized to satisfy the torque requirements, and will then be programmed using a Raspberry Pi to rotate the shaft at the calculated speed and dwelling times needed to fill each tank equally. In addition, we have also been advancing designs that use a camshaft and poppets. These are earlier on in their development, currently being sized to replicate the expected flow patterns of the rotary ball valve. Expected outcomes of this valve include bi-directionality, successful sealing under pressure, and accurate cycling.

D’Orsi, Nicholas↗

Friction and Wear of Unlubricated NiTiHf with Nitriding Surface Treatments

The unlubricated friction and wear properties of the superelastic materials NiTi and NiTiHf, treated by either gas nitriding or plasma nitriding, have been investigated. Pin on disk testing of the studied materials was performed at sliding speeds from 0.01 to 1m/s at normal loads of 1, 5 or 10N. For all of the studied friction pairs (NiTiHf pins vs. NiTi and NiTiHf disks) over the given parameters, the steady-state coefficients of friction varied from 0.22 to 1.6. Pin wear factors ranged from approximately 1E-6 against the NiTiHf and plasma nitrided disks to approximately 1E-4 for the gas nitrided disks. The plasma nitrided disks provided wear protection in several cases and tended to wear by adhesion. The gas nitrided treatment generated the most pin wear but had essentially no disk wear except at the most severe of the studied conditions (1N load and 1m/s sliding speed). The results of this study are expected to provide guidance for design of components such as gears and fasteners.

friction↗

Investigation of Bolt Preload Relaxation for JWST Thermal Heat Strap Assembly Joints with Aluminum-1100 and Indium Gaskets

Accurately predicting fastener preload relaxation in the James Webb Space Telescope (JWST) heat strap assemblies is essential to insure adequate thermal performance during its mission lifecycle. The mechanisms for preload relaxation in the strap joints include Al-1100 material creep, indium gasket flow-out, and embedment of the joint faying surfaces. This report documents the results from a bolted joint relaxation test, including analysis and curve fitting of the test data for predicting preloads five years after initial torque application. The report also includes the derivation of a preload uncertainty factor enveloping both torque/preload application scatter and expected preload relaxation at the end of mission life.

Joint↗

Investigation of Bolt Preload Relaxation for JWST Thermal Heat Strap Assembly Joints with Aluminum-1100 and Indium Gaskets

Accurately predicting fastener preload relaxation in the James Webb Space Telescope (JWST) heat strap assemblies is essential to insure adequate thermal performance during its mission lifecycle. The mechanisms for preload relaxation in the strap joints include Al-1100 material creep, indium gasket flow-out, and embedment of the joint faying surfaces. This report documents the results from a bolted joint relaxation test, including analysis and curve fitting of the test data for predicting preloads five years after initial torque application. The report also includes the derivation of a preload uncertainty factor enveloping both torque/preload application scatter and expected preload relaxation at the end of mission life.

Preload↗

Inductive Pulsed Plasma Thruster Development Testing at NASA-MSFC

The inductive pulsed plasma thruster (IPPT) is an electromagnetic plasma accelerator that has been identified in NASA roadmaps as an enabling propulsion technology for some niche low-power missions and for high-power in-space propulsion needs. The IPPT is an electrodeless space propulsion device where a capacitor is charged to an initial voltage and then discharged producing a high current pulse through a coil. The field produced by this pulse ionizes propellant, inductively driving current in a plasma located near the face of the coil. Once the plasma is formed it can be accelerated and expelled at a high exhaust velocity by the electromagnetic Lorentz body force arising from the interaction of the induced plasma current and the magnetic field produced by the current in the coil. Thrusters of this type possess many demonstrated and potential benefits that make them worthy of continued investigation. The electrodeless nature of these thrusters eliminates the lifetime and contamination issues associated with electrode erosion in conventional electric thrusters. Also, a wider variety of propellants are accessible when compatibility with metallic electrodes in no longer an issue. IPPTs have been successfully operated using propellants like ammonia, hydrazine, and CO2, and there is no fundamental reason why they would not operate on other in situ propellants like H2O. It is well-known that pulsed accelerators can maintain constant specific impulse (I(sub sp)) and thrust efficiency (η(sub t)) over a wide range of input power levels by adjusting the pulse rate to hold the discharge energy per pulse constant. It has also been demonstrated that an inductive pulsed plasma thruster can operate in a regime where η(sub t) is relatively constant over a wide range of I(sub sp) values (3000-8000 s). Finally, thrusters in this class have operated in single-pulse mode at high energy per pulse, and by increasing the pulse rate they offer the potential to process very high levels of power using a single thruster. There has been significant previous research on IPPTs designed around a planar-coil (flat-plate) geometry. The most notable of these was the Pulsed Inductive Thruster (PIT), with the PIT MkV presently representing the state of- the-art in pulsed high-power IPPT technological development. In this paper, we focus on two planar-geometry devices that operate at significantly different power levels. Most work performed at NASA-Marshall Space Flight Center (MSFC) has, to date, focused on lower power thruster operation (≈ 10s to 100s of J/pulse, up to 2-2.5 kW average power throughput) and previously described in Refs. [5,6]. The most recent work aimed to assemble a device that could be tested in cyclic mode on a thrust-stand, and which could augment the existing data set for IPPTs. In addition, the thruster was designed to serve as a test-bed for solid state switching circuitry and pulsed gas valves, with the modular design of the device allowing for variation in or upgrades to test configuration. Recently, MSFC obtained on loan from the Georgia Institute of Technology (Atlanta, GA) the PIT MkVI, successor to the PIT MkV. The MkV and MkVI are similar in design with much of the hardware from the former, specifically the capacitors and spark-gap switches, being reused in the latter. The coil is simliar in geometry but has bent copper rods used in the latest iteration in place of the Litz wire windings found in the MkV. The MkVI master switch for the spark gaps is located in the vacuum chamber contained within a sealed, pressurized vessel fastened to the back of the thruster. This is different from the MkV where many capacitor charging lines and spark gap-triggering delay lines ran to the thruster from a master trigger located outside the vacuum chamber. The MkVI was damaged during testing soon after its fabrication was completed. The thruster arrived at MSFC still-damaged and mostly disassembled into many individual pieces. The device has been repaired, with a few additional design changes implemented after discussions with the late Prof. Lovberg regarding the initial testing results and issues encountered.

Polzin, Kurt A.↗

Design of Multifunctional Hierarchical Space Structures

We describe a system for the design of space structures with tunable structural properties based on the discrete assembly of modular lattice elements. These lattice elements can be constructed into larger beam-like elements, which can then be assembled into large scale truss structures. These discrete lattice elements are reversibly assembled with mechanical fasteners, which allows them to be arbitrarily reconfigured into various application-specific designs. In order to assess the validity of this approach, we design two space structures with similar geometry but widely different structural requirements: an aerobrake, driven by strength requirements, and a precision segmented reflector, driven by stiffness and accuracy requirements. We will show agreement between simplified numerical models based on hierarchical assembly and analytical solutions. We will also present an assessment of the error budget resulting from the assembly of discrete structures. Lastly, we will address launch vehicle packing efficiency issues for transporting these structures to lower earth orbit.

Aeronautics↗

Characterizing Material Scalability for Ultralight Lattice Design

Stiff yet ultra-light lattice structures constructed using digital materials have many practical applications as the building block for aircraft and other structures. By furthering our understanding of how material configuration affects the structural properties of an ultralight lattice, we can intelligently design these structures based on their intended function. Here we compare the behavior of ultralight lattice structures when fabricated by different materials. The individual unit cells of the lattice structures are referred to as voxels. The stiffness, elastic modulus, and yield strength of the specimens in compression and tension are determined through mechanical testing. Specimens are tested both as single voxel as well as 4x4x4 voxel constructions on an Instron 5982 Universal Testing System until failure. Each voxel is manufactured in bulk through injection molding, with a unit cell pitch of 76.2 mm. Individual voxels are fastened with machine screws and nuts to create assemblies. Four separate materials are used as voxel compositions in this experiment. These include a homogeneous polymer referred to as Ultem 1000, a glass-fiber reinforced polymer referred to as Ultem 2200, a polymer with chopped carbon fibers as 30% of its fill, and homogenous polypropylene. This work compares mechanical behavior, as well as the convergence behavior of the lattice as the size of the lattice assembly increases for various materials. The goal of this study is to characterize the behavior of homogenous lattices such that heterogenous lattices can be designed with different material voxels to achieve target material properties for ultralight space applications.

Sajjadi, Afsheen↗

The Effect of Hole Quality on the Bearing Strength of Carbon Fiber Laminates

On programs involving flight hardware for launch vehicles that the author has been involved in over the years, the question always arises as to how to best machine and inspect holes drilled for fasteners. While common sense dictates that ‘well-drilled’ holes are desired over ‘poorly drilled’ holes for bolt bearing applications, the effect of hole quality on the bearing strength of carbon fiber laminates has not been extensively studied in the open literature. If this effect is not quantitatively known, the question of what hole quality needs to be required for the flight hardware cannot be answered. In addition, the function of the part with respect to the holes needs to be taken into account. There is no such thing as a defect-free hole since some chip-out of fibers within the hole will occur regardless of drill bit and backing plate pressure. For most holes machined in a carbon fiber laminate, some extent of delamination and fiber breakout on the entrance and exit of the hole is going to occur. Much time and money can be spent on trying to perfect the drilling technique and subsequent inspection of holes in carbon fiber laminates, including adding extra plies of cloth to the surfaces to help prevent fiber breakout; but is this effort really justified if little-to-no increase in bearing strength is realized by good-quality holes over those of lesser quality?

Nettles, A. T.↗

Molecular Dynamics Investigation of the Structural and Mechanical Properties of Off-Stoichiometric Epoxy Resins

We carried out molecular dynamics (MD) simulations to measure the mechanical properties of various off-stoichiometric polymers regarding amine to epoxy ratios (r) and to understand the stiffness of the polymers in terms of their structures. The aerospace-grade API-60 epoxy resin is used as an adhesive bond for assembling large-scale composite structures via the co-curing-ply bonding method. This method will produce a reliable and certifiable composite joint without additional fasteners. Calculated Young's modulus was measured from the uniaxial tension simulation with several high strain rates, and the experimental modulus was estimated by extrapolating the simulation results. We found that the stiffness was associated with molecular packing caused by chemical cross-linking. We also found that the number of network clusters gradually decreased as the ratio approached r = 1.0, which made the tighter cluster and the system much stiffer with an increase in the molecular weight and the degree of cross-linking. Structural properties such as Rg, MSD were measured to figure out the degree of stiffness with respect to the r.

Jang, Chang Woon↗

STITCHED COMPOSITES WITH THREE-DIMENSIONAL STITCH PATHS

Stitched composites have been shown to exhibit damage tolerance and to reduce weight compared to traditional layered composites through unitization of the structure by elimination of fasteners. Stitching capabilities have been incorporated into the Integrated Structural Assembly of Advanced Composites (ISAAC) system at NASA Langley Research Center with the introduction of two stitching heads. Stitching path control was initially implemented as straight lines in space, as was done for previous stitching development. However, more complex stitched structures such as a wind tunnel blade or around cutouts within a fuselage or wing skin, require that the stitching paths be implemented as three-dimensional (3D) stitching paths in space. Unfortunately, control programming output by an existing preprocessor program cannot stitch these curved paths due to problems that arise in stitch formation and the introduction of side forces on the needles using the conventional programming approach whereby the head is simultaneously controlled through translations and rotations. This lack of capability is most significant for the single-sided stitching head, where two needles are in the preform at the same time for the majority of the stitching process. A means to program 3D stitching paths in space was developed whereby the translation and rotation of each stitch were decoupled, thereby eliminating the problems associated with current control programming approach. Using this newly developed stitching path definition and control programming, complex stitching paths have successfully been stitched at the ISAAC facility. The ability to stitch general 3D stitching paths in space enables the use of stitching on more complex parts.

carbon-epoxy↗

Stitched Composites with Three-Dimensional Stitch Paths

Stitched composites have been shown to exhibit damage tolerance and to reduce weight compared to traditional layered composites through unitization of the structure by elimination of fasteners. Stitching capabilities have been incorporated into the Integrated Structural Assembly of Advanced Composites (ISAAC) system at NASA Langley Research Center with the introduction of two stitching heads. Stitching path control was initially implemented as straight lines in space, as was done for previous stitching development. However, more complex stitched structures such as a wind tunnel blade or around cutouts within a fuselage or wing skin, require that the stitching paths be implemented as three-dimensional (3D) stitching paths in space. Unfortunately, control programming output by an existing preprocessor program cannot stitch these curved paths due to problems that arise in stitch formation and the introduction of side forces on the needles using the conventional programming approach whereby the head is simultaneously controlled through translations and rotations. This lack of capability is most significant for the single-sided stitching head, where two needles are in the preform at the same time for the majority of the stitching process. A means to program 3D stitching paths in space was developed whereby the translation and rotation of each stitch were decoupled, thereby eliminating the problems associated with current control programming approach. Using this newly developed stitching path definition and control programming, complex stitching paths have successfully been stitched at the ISAAC facility. The ability to stitch general 3D stitching paths in space enables the use of stitching on more complex parts.

carbon-epoxy↗

Atoms to Aircraft to Spacecraft

The next generation of aerospace systems requires materials and structures that combine high performance at high utilization in short missions with the possibility of high rate production, without excessive non-recurring cost, to allow for rate flexibility and shorter structural life cycles. The development of materials and structures that offer this flexibility in rate without negatively influencing performance and economic viability will require a matching and overlapping experimental and computational design approach. The objective is to go from Atom to Airframe to Spaceframe for thermoplastic unidirectional tape based fastener-free assemblies. Thermoplastic composites are chosen as the focus because these materials allow for reversible fusion bonding in every stage of their life cycle after synthesis. Our strategy is to combine multi-scale computational approaches with multi-scale experimental activities to develop an understanding of and capabilities to manufacture custom unidirectional thermoplastic tape. This tape will be the basis for our high-rate multiple-technology manufacturing approach validated by the production of two representative demonstrators for urban air mobility vehicle structures. The multi-disciplinary team will work in an integrated manner to effectively combine computational approaches with experimental approaches at each stage of characteristic manufacturing flows. The team aims for tools and technology to quantify the thermo-rheological aspects of unidirectional tape-based production and assembly of aerospace quality thermoplastic components as well as for validated tools for unidirectional tape-based thermoplastic preform and part design and manufacture. The work will be used to design and build two demonstration structural parts characteristic for urban air mobility vehicles.

Paul Ziehl↗

NASA Facts: AERoBOND Project

Sustainability of the commercial air travel industry requires new aircraft with ultra-efficient structures and designs, which will depend largely on lightweight polymer composites and new assembly methods. Manufacturers of commercial transport aircraft are compelled to install thousands of redundant fasteners into bonded joints to prevent failures due to unpredictable weak bonds. The Adhesive-Free Bonding of Complex Composites (AERoBOND) process enables re-flow of matrix resin during assembly to eliminate the material discontinuity at the interface, thereby eliminating the dependence of mechanical performance on interfacial adhesion.

Frank Louis Palmieri↗

Molecular Dynamics Investigation of the Structural and Mechanical Properties of Off-Stoichiometric Epoxy Resins

Molecular dynamic (MD) simulations were performed to compute the mechanical properties of off-stoichiometric epoxy resins as a function of hardener/epoxy mixture ratio (r). Properties were characterized in relation to their microscopic structures. Such resins have been used recently for adhesive-free bonding of large-scale composite structures using the co-curing-ply method. In this process, two partially precured composite panels with hardener-poor (HP) off-stoichiometric resins are coupled with ply(ies) of complementary hardener-rich (HR) formulations and then cured simultaneously. This bonding process has the potential to produce reliable and certifiable composite joints without the need for additional fasteners, which are often required for many conventional bonding methods because even small amounts of contamination can cause a weak bond. The reflow and mixing of the HP/HR resin in this bonding process result in a joint with no discernable interface that should not be susceptible to surface contamination. However, incomplete mixing of the two offset resins may result in chemical heterogeneity of the cured polymeric joint. Thus, different r values may be obtained across the joint. Classical MD simulations were performed to compute the Young’s modulus of polymers with different r values and correlate their properties to network structures. High stiffness was associated with molecular packing due to chemical crosslinking, leading to a single network structure. Moreover, the networks became denser as the ratio approached the stoichiometric value r = 1. Thus, the r = 1 systems were single clusters, with high stiffness, high molecular weight, and a high degree of crosslinking. Structural properties such as radius of gyration and mean square displacement were determined to investigate the variation in the stiffness with respect to r. This MD simulation study was validated with experimental measurements.

Chang Woon Jang↗

Closed-Loop Control of Laser Surface Treatment via Laser Induced Breakdown Spectroscopy

Current composite manufacturing rates need to be improved to meet the projected demand of on-demand mobility (ODM) and commercial aircraft transports. Some processes in the composite manufacturing chain require touch labor such as manual sanding of surfaces prior to bonding and installing thousands of mechanical fasteners in bonded primary structures to achieve Federal Aviation Administration (FAA) certification. The consequences are insufficient repeatability in bond quality resulting in increased manufacturing time. The FAA has indicated that robust process control is one potential means of certifying bondlines in primary structure. This work describes an integrated closed-loop control system between a laser machining system and laser induced breakdown spectroscopy (LIBS) instrumentation as a means of assuring bond performance and achieving certified composite bondlines. Preliminary results from in-situ treatment and inspection are presented. Results indicate that LIBS inspection and laser treatment can be conducted simultaneously to achieve high quality, reliable adhesive bonds.

Rodolfo Ledesma↗

Closed-Loop Control of Laser Surface Treatment via Laser Induced Breakdown Spectroscopy

Current composite manufacturing rates need to be improved to meet the projected demand of on-demand mobility (ODM) and commercial aircraft transports. Some processes in the composite manufacturing chain require touch labor such as manual sanding of surfaces prior to bonding and installing thousands of mechanical fasteners in bonded primary structures to achieve Federal Aviation Administration (FAA) certification. The consequences are insufficient repeatability in bond quality resulting in increased manufacturing time. The FAA has indicated that robust process control is one potential means of certifying bondlines in primary structure. This work describes an integrated closed-loop control system between a laser machining system and laser induced breakdown spectroscopy (LIBS) instrumentation as a means of assuring bond performance and achieving certified composite bondlines. Preliminary results from in-situ treatment and inspection are presented. Results indicate that LIBS inspection and laser treatment can be conducted simultaneously to achieve high quality, reliable adhesive bonds.

Rodolfo Ledesma↗

Improved Method for Increased-Rate Stitched Composites Manufacturing

Stitched composites, as defined herein, are created by stitching a dry preform, infusing the preform with resin and curing the resin. Stitched composites have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. However, conventional stitched composite structure production is very time and manual-labor intensive, and therefore is not conducive for high-rate production of commercial aircraft main structure. The National Aeronautics and Space Administration (NASA) Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project has the objective to increase the manufacturing rate for future composite aircraft. Stitched resin infused (SRI) composites are one of the technologies being considered under the HiCAM Project, but to be viable, production rates must be increased (i.e., production time reduced). Previous work has shown that it is possible to reduce the time required to stitch a dry composite preform, such as a skin with integral stiffeners, but the stitching process is a small portion of the total time required to produce a stitched preform. To significantly reduce overall stitched preform production time, a study was undertaken to examine a new stitching method that would yield time reduction in the pre- and post-stitching activities that include all portions of a stitched preform production with the exception of the actual stitching process. The new method resulted in significant reduction in production time, from 27% to 40%, while at the same time reducing the costs associated with fabricating a stitched preform by eliminating stations within the production line, simplifying tooling, reducing labor, and reducing consumables.

Stitching↗

Improved Method for Increased-Rate Stitched Composites Manufacturing

Stitched composites, as defined herein, are created by stitching a dry preform, infusing the preform with resin and curing the resin. Stitched composites have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. However, conventional stitched composite structure production is very time and manual-labor intensive, and therefore is not conducive for high-rate production of commercial aircraft main structure. The National Aeronautics and Space Administration (NASA) Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project has the objective to increase the manufacturing rate for future composite aircraft. Stitched resin infused (SRI) composites are one of the technologies being considered under the HiCAM Project, but to be viable, production rates must be increased (i.e., production time reduced). Previous work has shown that it is possible to reduce the time required to stitch a dry composite preform, such as a skin with integral stiffeners, but the stitching process is a small portion of the total time required to produce a stitched preform. To significantly reduce overall stitched preform production time, a study was undertaken to examine a new stitching method that would yield time reduction in the pre- and post-stitching activities that include all portions of a stitched preform production with the exception of the actual stitching process. The new method resulted in significant reduction in production time, from 27% to 40%, while at the same time reducing the costs associated with fabricating a stitched preform by eliminating stations within the production line, simplifying tooling, reducing labor, and reducing consumables.

Stitching↗