Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Development of an interatomic potential for the simulation of defects, plasticity, and phase transformations in titanium

New interatomic potentials describing defects, plasticity, and high temperature phase transitions for Ti are presented. Fitting the martensitic hcp-bcc phase transformation temperature requires an efficient and accurate method to determine it. We apply a molecular dynamics method based on determination of the melting temperature of competing solid phases, and Gibbs-Helmholtz integration, and a lattice-switch Monte Carlo method: these agree on the hcp-bcc transformation temperatures to within 2 K. We were able to develop embedded atom potentials which give a good fit to either low or high temperature data, but not both. The first developed potential (Ti1) reproduces the hcp-bcc transformation and melting temperatures and is suitable for the simulation of phase transitions and bcc Ti. Two other potentials (Ti2 and Ti3) correctly describe defect properties and can be used to simulate plasticity or radiation damage in hcp Ti. The fact that a single embedded atom method potential cannot describe both low and high temperature phases may be attributed to neglect of electronic degrees of freedom, notably bcc has a much higher electronic entropy. As a result, a temperature-dependent potential obtained from the combination of potentials Ti1 and Ti2 may be used to simulate Ti properties at any temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Elastic-plastic deformation of molybdenum single crystals shocked along [100]

To understand the elastic-plastic deformation response of shock-compressed molybdenum (Mo) – a body-centered cubic (BCC) metal, single crystal samples were shocked along the [100] crystallographic orientation to an elastic impact stress of 12.5 GPa. Elastic-plastic wave profiles, measured at different propagation distances ranging between ~0.23 to 2.31 mm using laser interferometry, showed a time-dependent material response. Within experimental scatter, the measured elastic wave amplitudes were nearly constant over the propagation distances examined. These data point to a large and rapid elastic wave attenuation near the impact surface, before reaching a threshold value (elastic limit) of ~3.6 GPa. Numerical simulations of the measured wave profiles, performed using a dislocation-based continuum model, suggested that {110}<111> and/or {112}<111> slip systems are operative under shock loading. In contrast to shocked metal single crystals with close-packed structures, the measured wave profiles in Mo single crystals could not be explained in terms of dislocation multiplication alone. A dislocation generation mechanism, operative for shear stresses larger than that at the elastic limit, was required to model the rapid elastic wave attenuation and to provide a good overall match to the measured wave profiles. However, the physical basis for this mechanism was not established for the high-purity single crystal samples used in this study. As a result, the numerical simulations also suggested that Mo single crystals do not work harden significantly under shock loading in contrast to the behavior observed under quasi-static loading.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Plastic dynamics of the Al 0.5 CoCrCuFeNi high entropy alloy at cryogenic temperatures: Jerky flow, stair-like fluctuation, scaling behavior, and non-chaotic state

This study reports on the plastic behavior of the Al 0.5 CoCrCuFeNi high-entropy alloy at cryogenic temperatures. The samples are uniaxially compressed at 4.2 K, 7.5 K, and 9 K. A jerky evolution of stress and stair-like fluctuation of strain are observed during plastic deformation. A scaling relationship is detected between the released elastic energy and strain-jump sizes. Furthermore, the dynamical evolution of serrations is characterized by the largest Lyapunov exponent. The largest Lyapunov exponents of the serrations at the three temperatures are all negative, which implies that the dynamical regime is non-chaotic. This trend reflects an ordered slip process, and this ordered slip process exhibits a more disordered slip process, as the temperature decreases from 9 K to 4.2 K or 7.5 K.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shock initiation and hot spots in plastic-bonded 1,3,5-triamino-2,4,6-trinitrobenzene (TATB)

TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is a powerful explosive whose dynamical behavior is difficult to study because TATB is so insensitive to initiation by shock waves. We used a tabletop microscope equipped with 0–4.5 km/s laser-launched flyer plates to study shock initiation of TATB, which was fabricated in the form of an array of hundreds of plastic-bonded explosive minicharges (X-TATB = 80% TATB + 20% Sylgard 182 polymer). The 4 ns shocks from the flyer plates were not effective in initiating TATB, but we also developed a two-layer array where flyers first initiated a plastic-bonded PETN (pentaerythritol tetranitrate) charge (X-PETN = 80% PETN + 20% Sylgard), which drove an initiating 25 ns shock into the X-TATB. Thermal emission from shocked X-TATB was used to measure time-dependent temperature profiles with a resolution of 2 ns and to produce high-speed (5 ns) videos. In X-TATB, flyer plates produced 2500–3500 K hot spots and combustion at 2500 K. With X-PETN initiators, X-TATB had 3500–4000 K hot spots and a powerful volume explosion lasting a few nanoseconds. Prospects for producing TATB detonations on a tabletop are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Single Crystal Plasticity Model with Deformation Twinning for the High Rate Deformation of β-HMX

Deformation twinning is an active deformation mechanism during loading along certain crystallographic directions of β-cyclotetramethylene tetranitramine (β-HMX). In this work, a finite strain thermomechanical model is extended to include twinning as a deformation mechanism in addition to plastic slip. The stress is derived from the free energy expression including a term representing the equation of state. The crystal plasticity framework is used to divide the total strain into inelastic and elastic component, where the elastic part is used in the expression for the free energy. The twin systems are treated as pseudo slip systems and the shear rate on the twin systems is evaluated in terms of the twin resistance and the projection of the stress tensor. The model parameters were calibrated against a set of plate impact experiments performed on β-HMX by Dick et al. The remaining plate impact experiments are used to evaluate the predictive capability of the model. The quality of the model fits and predictions is discussed from a physical and modeling perspective. Particularly, the role of twin modeling on results is highlighted. Finally, the model is used to explore the relationship between the propensity for twinning and crystal orientation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Intrinsic synaptic plasticity of ferroelectric field effect transistors for online learning

Nanoelectronic devices emulating neuro-synaptic functionalities through their intrinsic physics at low operating energies is imperative toward the realization of brain-like neuromorphic computers. In this work, we leverage the non-linear voltage dependent partial polarization switching of a ferroelectric field effect transistor to mimic plasticity characteristics of biological synapses. Here, we provide experimental measurements of the synaptic characteristics for a 28nm high-k metal gate technology based device and develop an experimentally calibrated device model for large-scale system performance prediction. Decoupled read-write paths, ultra-low programming energies and the possibility of arranging such devices in a cross-point architecture demonstrate the synaptic efficacy of the device. Our hardware-algorithm co-design analysis reveals that the intrinsic plasticity of the ferroelectric devices has potential to enable unsupervised local learning in edge devices with limited training data

42 ENGINEERING↗
DOE OSTI2026

Hot electron preheat effects in two-photon polymerization plastic lattice laser-driven shock-tube experiments on the OMEGA laser

We present simulations of Omega shock tube experiments designed to investigate hot electron preheat effects in 3D-printed, two-photon polymerization (2PP) plastic lattices. Preheat is inferred in the experiments from the expansion of a plastic witness disk embedded in the lattice. Using the Eulerian radiation-hydrodynamics code xRAGE, we model shock propagation and preheat from both radiative and hot electron energy sources to evaluate their relative impact. To simulate the transport of laser-generated hot electrons, the nonlocal electron heat transport model proposed by Schurtz, Nicolaï, and Busquet (SNB) is extended with a hot electron source term and an energy cascade algorithm. We explore how variations in ablator, lattice geometry, and laser drive affect the shock velocity and witness disk expansion. Simulations show that the inclusion of a 5 μm gold layer reduces shock pressure by 60% and shock speeds by 30%–40% but does not significantly reduce the hot electron preheat, and that different lattice geometries lead to enhanced shock velocities—up to 40% faster than in homogeneous foams. However, radiative and conductive preheat from classical mechanisms alone fail to match experiment. By including a hot electron source term, we reproduce experimental observables such as disk expansion rates and spatial radiographic features. We find that a hot electron population corresponding to 4%–8% of the incident laser energy with T hot = 50 keV produces expansion which agrees with the experimental data, suggesting hot electron preheat is the most plausible explanation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Characterization and engineering of a two-enzyme system for plastics depolymerization

Significance Deconstruction of recalcitrant polymers, such as cellulose or chitin, is accomplished in nature by synergistic enzyme cocktails that evolved over millions of years. In these systems, soluble dimeric or oligomeric intermediates are typically released via interfacial biocatalysis, and additional enzymes often process the soluble intermediates into monomers for microbial uptake. The recent discovery of a two-enzyme system for polyethylene terephthalate (PET) deconstruction, which employs one enzyme to convert the polymer into soluble intermediates and another enzyme to produce the constituent PET monomers (MHETase), suggests that nature may be evolving similar deconstruction strategies for synthetic plastics. This study on the characterization of the MHETase enzyme and synergy of the two-enzyme PET depolymerization system may inform enzyme cocktail-based strategies for plastics upcycling.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Ultrahigh strength and plasticity in laser rapid solidified Al–Si nanoscale eutectics

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microfabrication of plastic-PDMS microfluidic devices using polyimide release layer and selective adhesive bonding

In this study, we present an improved method to bond poly(dimethylsiloxane) (PDMS) with polyimide (PI) to develop flexible substrate microfluidic devices. The PI film was separately fabricated on a silicon wafer by spin coating followed by thermal treatment to avoid surface unevenness of the flexible substrate. In this way, we could also integrate flexible substrate into standard micro-electromechanical systems (MEMS) fabrication. Meanwhile, the adhesive epoxy was selectively transferred to the PDMS microfluidic device by a stamp-and-stick method to avoid epoxy clogging the microfluidic channels. To spread out the epoxy evenly on the transferring substrate, we used superhydrophilic vanadium oxide film coated glass as the transferring substrate. After the bonding process, the flexible substrate could easily be peeled off from the rigid substrate. Contact angle measurement was used to characterize the hydrophicity of the vanadium oxide film. X-ray photoelectron spectroscopy analysis was conducted to study the surface of the epoxy. We further evaluated the bonding quality by peeling tests, which showed a maximum bonding strength of 100 kPa. By injecting with black ink, the plastic microfluidic device was confirmed to be well bonded with no leakage for a day under 1 atm. Finally, this proposed versatile method could bond the microfluidic device and plastic substrate together and be applied in the fabrication of some biosensors and lab-on-a-chip systems.

42 ENGINEERING↗
DOE OSTI2017

Crystal plasticity modeling of β phase deformation in Ti-6Al-4V

Ti-6Al-4V is an alloy of titanium that dominates titanium usage in applications ranging from mass-produced consumer goods to high-end aerospace parts. The material's structure on a microscale is known to affect its mechanical properties but these effects are not fully understood. Specifically, this work will address the effects of low volume fraction intergranular β phase on Ti-6Al-4V's mechanical response during the transition from elastic to plastic deformation. A crystal plasticity-based finite element model is used to fully resolve the deformation of the β phase for the first time. This high fidelity model captures mechanisms difficult to access via experiments or lower fidelity models. Lastly, the results are used to assess lower fidelity modeling assumptions and identify phenomena that have ramifications for failure of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Crystal plasticity based constitutive modeling of ZEK100 magnesium alloy combined with in-situ HEXRD experiments

In the current works, both micro- and macro-mechanical properties of a hexagonal close-packed (HCP) polycrystalline ZEK100 magnesium alloy were investigated. In the experimental perspective, in-situ high energy X-ray diffraction (HEXRD) from a synchrotron source was conducted during the uniaxial tension along the rolling direction (RD) and the transverse direction (TD) to measure the lattice strain evolutions and stress-strain behaviors. In the modeling perspective, crystal plasticity finite element (CPFE) model was developed incorporating the deformation twinning for the HCP-structured metals. The HEXRD experiments and crystal plasticity models were then coupled to characterize the constitutive behaviors of the ZEK100 alloy. The lattice strain data representing the microscopic behavior of the material and the macroscopic stress-strain behavior were then tied together as objective values to estimate the critical resolved shear stress (CRSS) and hardening parameters of available slip and twin systems of the ZEK100 alloy using the developed CPFE model. The stress-strain behavior as well as the lattice strain variation during the uniaxial tension tests are presented using the CPFE model and compared with the actual HEXRD data.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Brightness and uniformity measurements of plastic scintillator tiles at the CERN H2 test beam

Here, we study the light output, light collection efficiency and signal timing of a variety of organic scintillators that are being considered for the upgrade of the hadronic calorimeter of the CMS detector. The experimental data are collected at the H2 test-beam area at CERN, using a 150 GeV muon beam. In particular, we investigate the usage of over-doped and green-emitting plastic scintillators, two solutions that have not been extensively considered. We present a study of the energy distribution in plastic-scintillator tiles, the hit efficiency as a function of the hit position, and a study of the signal timing for blue and green scintillators.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Measurement of proton quenching in a plastic scintillator detector

The non-linear energy response of the plastic scintillator EJ-260 is measured with the MicroCHANDLER detector, using neutron beams of energy 5 to 27 MeV at the Triangle Universities Nuclear Laboratory. The first and second order Birks' constants are extracted from the data, and found to be $k_B = (8.70 \pm 0.93)\times 10^{-3}\ {\rm g/cm^2/MeV}$ and $k_C = (1.42 \pm 1.00) \times 10^{-5}\ {\rm (g/cm^2/MeV)^2}$. This result covers a unique energy range that is of direct relevance for fast neutron backgrounds in reactor inverse beta decay detectors. Furthermore, these measurements will improve the energy non-linearity modeling of plastic scintillator detectors. In particular, the updated energy response model will lead to an improvement of fast neutron modeling for detectors based on the CHANDLER reactor neutrino detector technology.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2019

Investigation of plastic yielding in near-micrometer grain size aluminum using synchrotron microdiffraction

The onset of plastic yielding has been studied in samples of aluminum with nearmicrometer average grain size using in situ tensile loading combined with synchrotron radiation. A white-beam Laue 3D micro-diffraction technique was used allowing the collection of diffraction signal from a volume with a resolution of 1 μm in all three dimensions. The orientation data obtained from the micro-diffraction are used to estimate the local variation in geometrically necessary dislocation density, and correction factors are suggested for voxels where neighbors are missing in either one or two dimensions. The results demonstrate a considerable heterogeneity in deformation in the early stages of plastic deformation.

Zhang, C L↗
DOE OSTI2023

Torrefaction of almond shell as a renewable reinforcing agent for plastics: techno-economic analyses and comparison to bioethanol process

Abstract In 2016, the US state of California alone produced nearly 3.5 billion kilograms of almonds, accounting for approximately 84% of the world’s almond production. This generated about 2.58 million metric tons (MTs) of almond residues. Almond shells are currently either burned to generate power or disposed of in landfill. Valorizing almond shells and hulls provides an opportunity to replace petroleum-derived products and divert organic material from landfill. Here we demonstrate a detailed techno-economic analysis (TEA) of an almond shell torrefaction process capable of utilizing the 520 000 MTs of almond shells produced annually in California. Our process also includes preprocessing the torrefied biomass to exploit it as a reinforcing agent for plastics. We further compared the revenue generated from the torrefied biomass and bioethanol derived from the same quantity of almond shells. We considered three different torrefaction facility scales to evaluate trade-offs between economies of scale at the facility and trucking costs to deliver almond shells. A facility that takes in 200 000 MT yr –1 of almond shells results in lower per-unit-output basis capital and operating cost relative to other smaller-scale torrefaction facilities, including 10 000 MT yr –1 and 50 000 MT yr –1 , considered for analysis in this study. The large-sale facility results in a minimum selling price (MSP) of the torrefied biomass of $311.4 MT –1 . An analogous TEA on converting almond residues into bioethanol is also investigated. The MSP of almond shell derived ethanol ($1.71 kg −1 ) is higher than that of corn ($0.48 kg −1 ) or cellulosic biomass ($0.88 kg −1 ) derived ethanol. Compared with the bioethanol route, the torrefied almond shells result in three times more revenue if utilized as a reinforcing agent for plastics.

Liu, Dupeng (ORCID:0000000269514064)↗
DOE OSTI2017

Scaling Symmetries in Elastic-Plastic Dynamic Cavity Expansion Equations Using the Isovector Method

Cavity-expansion approximations are widely-used in the study of penetration mechanics and indentation phenomena. We apply the isovector method to a well-established model in the literature for elastic-plastic cavity-expansion to systematically demonstrate the existence of Lie symmetries corresponding to scale-invariant solutions. Here we use the symmetries obtained from the equations of motion to determine compatible auxiliary conditions describing the cavity wall trajectory and the elastic-plastic material interface. The admissible conditions are then compared with specific similarity solutions in the literature.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Sustainable production of plastic-degrading enzymes in Chlamydomonas pacifica

AbstractThe discovery of a new extremophile alga,Chlamydomonas pacifica, provides an opportunity to expand on heterologous protein expression beyond the traditionalChlamydomonas reinhardtii. C. pacificais a unicellular extremophile capable of surviving at high pH, high temperatures, and high salinity. These various growth conditions allow C. pacifica to outcompete any invading contaminants in open-air environments. Developing this novel species as a platform for recombinant protein production could significantly advance commercial microalgal recombinant protein production. We have previously shown thatC. reinhardtiican secrete a plastic-degrading enzyme: a PETase known as PHL7. This PETase is capable of cleaving ester bonds and has been used commercially for the degradation of PET plastics. However, the expression of such an enzyme has yet to be done in open raceway ponds and on a large scale. Here, we describe the culturing of PHL7 transgenic C. pacifica strain in three 80L raceway ponds and the measurements of recombinant enzymatic expression and activity found in the culture media. Our work provides proof of concept that this new organism can produce functional PHL7 enzymes in addition to producing the valuable components that inherently exist in theC. pacificaalgae biomass.Graphical Abstract

Diaz, Crisandra Jade (ORCID:0000000173429041)↗