SEARCH · Search NASA

Results for “PLATES - ELASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Analytical results for post-buckling behaviour of plates in compression and in shear

The postbuckling behavior of long rectangular isotropic and orthotropic plates is determined. By assuming trigonometric functions in one direction, the nonlinear partial differential equations of von Karman large deflection plate theory are converted into nonlinear ordinary differential equations. The ordinary differential equations are solved numerically using an available boundary value problem solver which makes use of Newton's method. Results for longitudinal compression show different postbuckling behavior between isotropic and orthotropic plates. Results for shear show that change in inplane edge constraints can cause large change in postbuckling stiffness.

Stein, M.↗

NASA NTRS1987

Test results of a pumped two-phase mounting plate with ammonia

The design, fabrication, and testing of full-scale prototype units of a two-phase mounting plate (TPMP), which will be used in a two-phase ammonia-based thermal control system for a large spacecraft, are described. The mounting plate uses an evaporator design in which liquid is mechanically pumped through porous feed tubes within the plate. The prototype TPMPs were tested with ammonia at heat loads over 3000 W (3.2 W/sq cm) and local heat fluxes of up to 4 W/sq cm. Calculated total heat transfer coefficients from these tests were between 0.8 and 1.0 W/sq cm per C. This represents a better than twenty-fold improvement over comparable single-phase heat transfer coefficients. Design diagrams are included.

Swanson, T. D.↗

NASA NTRS1987

Remote measurement of in-plane diffusivity components in plates

A method of determining thermal diffusivity in thin plates is presented. The method, using infrared images of evolving thermal patterns previously injected with a laser, is noncontacting, one-sided, and remote. It does not require independent estimates of either the emissivity of the sample or the sample thickness. With a line-segment pattern for thermal input, it yields the inplane components of the diffusivity tensor in anisotropic materials and also the rate of heat loss to the environment of the plate. Two methods of data analysis are presented, one corresponding to a heating line of general cross section and the other considering a Gaussian cross section, thereby saving considerable computer time. Both methods produce a statistical evaluation of measurement quality as well as estimates of diffusivity and loss rate. Results are shown for plates of metals and graphite-epoxy composite materials. Principal components and orientation for the diffusivity tensor are obtained in the anisotropic graphite-epoxy sample.

Welch, Christopher S.↗

NASA NTRS1987

Further generalization of an equivalent plate representation for aircraft structural analysis

Recent developments from a continuing effort to provide an equivalent plate representation for aircraft structural analysis are described. Previous work provided an equivalent plate analysis formulation that is capable of modeling aircraft wing structures with a general planform such as cranked wing boxes. However, the modeling is restricted to representing wing boxes having symmetric cross sections. Further developments, which are described in this paper, allow modeling of wing cross section having asymmetries that can arise from airfoil camber or from thicknesses being different in the upper and lower cover skins. An implementation of thermal loadings, which are described as temperature distributions over the planform of the cover skins, has been included. Spring supports have been added to provide for a more general set of boundary conditions. Numerical results are presented to assess the effect of wing camber on the static and dynamic response of an example wing structure under pressure and thermal loading. These results are compared with results from a finite element analysis program to indicate how well a cambered wing box can be represented with an equivalent plate formulation.

Giles, Gary L.↗

NASA NTRS1987

Vector constraints on western U.S. deformation from space geodesy, neotectonics, and plate motions

The rate-of-slip vector on the San Andreas fault in central California estimated from geodetic and Holocene geological data is inconsistent with the prediction of rigid plate models such as RM2. This well-known 'San Andreas discrepancy' is diagnostic of plate deformation distributed both east of the fault in the Basin and Range and west of the fault along the California continental margin. Constraints on the integrated deformation rates across these two regions consistent with: (1) the kinematical boundary conditions imposed by the rigid plate model; (2) neotectonic and paleoseismic estimates of deformation rates; (3) ground-based geodetic measurements; and (4) rates of change observed by very long baseline interferometry along seven baselines to western U.S. sites are constructed. The space-geodetic data on Basin and Range extension taken over a 4-year interval are compatible with geological observations averaged over the Holocene; the best estimate of its integrated deformation rate, provided by the joint inversion of both data types, is 9.7 + or - 2.1 mm/yr, N 56 deg W + or - 10 deg, too small and in the wrong direction to account entirely for the San Andreas discrepancy. The integral of this deformation, estimated by subtracting the Basin and Range contribution from the discrepancy vector, requires significant right-lateral shear parallel to the San Andreas (13 + or - 5 mm/yr) and some compression perpendicular to it (9 + or - 3 mm/yr).

Minster, J. Bernard↗

NASA NTRS1987

An efficient quadrilateral element for plate bending analysis

A simple, shear flexible, quadrilateral plate element is developed based on the Hellinger/Reissner mixed variational principle with independently assumed displacement and stress fields. The crucial point of the selection of appropriate stress parameters is emphasized in the formulation. For this purpose, a set of guidelines is formulated based on the follwoing considerations: (1) suppression of all kinematic deformation modes, (2) the element has a favorable value for the constraint index in the thin plate limit, and (3) element properties are frame-invariant. For computer implementation the components of the element stiffness matrix are evaluated analytically using the symbolic manipulation package MACSYMA. The effectiveness and practical usefulness of the proposed element are demonstrated by the numerical results of a variety of problems involving thin and moderately thick plates under different loading and support conditions.

Saleeb, A. F.↗

NASA NTRS1987

Interaction of airborne and structure-borne noise radiated by plates

The interaction of airborne and structure-borne noise radiated by aircraft structures is studied analytically and experimentally for the case of noise radiating from thin, isotropic, rectangular aluminum plates as a result of fully coherent, combined acoustic and vibrational inputs. Attention is given to the great influence of the relative phase between inputs on the combined noise radiation characteristics of the plates; these phase-dependent effects, which are manifest as cross-terms in both the dynamic and acoustic portions of the analysis, can radically alter the combined sound power radiated by airframe structure plates. Such interactive effects have heretofore been neglected in analyses of results from analytical and experimental studies of propeller-driven aircraft interior noise.

Mcgary, M. C.↗

NASA NTRS1987

Quantum efficiencies of imaging detectors with alkali halide photocathodes. I - Microchannel plates with separate and integral CsI photocathodes

Measurements and comparisons have been made of the quantum efficiencies of microchannel plate (MCP) detectors in the far-UV (below 2000-A) wavelength range using CsI photocathodes (a) deposited on the front surfaces of microchannel plates and (b) deposited on solid substrates as opaque photocathodes with the resulting photoelectrons input to microchannel plates. The efficiences were measured in both pulse-counting and photodiode modes of operation. Typical efficiencies are about 15 percent at 1216 A for a CsI-coated MCP compared with 65 percent for an opaque CsI photocathode MCP detector. Special processing has yielded an efficiency as high as 20 percent for a CsI-coated MCP. This may possibly be further improved by optimization of the tilt angle of the MCP channels relative to the front face of the MCP and incident radiation. However, at present there still remains a factor of at least 3 quantum efficiency advantage in the separate opaque CsI photocathode configuration.

Carruthers, George R.↗

NASA NTRS1986

Radiative and free-convective heat transfer from a finite horizontal plate inside an enclosure

An experimental and analytical investigation of heat transfer from a horizontal, thin, square plate inside of an enclosure was carried out. Experimental results were obtained from both the upward-facing and the downward-facing sides of the heated plate. Starting with the integrated momentum and energy equations, approximate solutions were obtained for heat transfer in the laminar and the turbulent regime that correlate well with experimental data. Radiative heat transfer correction was given special attention. Effects of the enclosure-related recirculation of the test fluid, as well as effects of simultaneous heat transfer on both sides of the plate, caused an early transition, and indicated a high level of internal turbulence.

Hrycak, Peter↗

NASA NTRS1988

Acousto-ultrasonic input-output characterization of unidirectional fiber composite plate by SV waves

A unidirectional fiberglass epoxy compostie specimen is modelled as a homogeneous transversely isotropic continuum plate medium. Acousto-ultrasonic noncontact input-output characterization is studied theoretically with a transmitting and a receiving transducer located on the same face of the plate. The single reflection problem for an incident SV wave at a plane boundary in transversely isotropic medium is analyzed. An obliquely incident SV wave results in a reflected SV wave and a reflected P wave for an angle of incidence of the incident SV wave less than the critical angle. Otherwise, there exists only an SV wave in the medium as the reflected P wave degenerates into a surface wave travelling parallel to the plane boundary. The amplitude ratio of the reflected SV wave is -1 when the angle of incidence is greater than or = the critical angle. The directional dependence of the phase velocity of the SV wave propagating in the transversely isotropic medium has a significant effect on the delay time, as opposed to the directional independence of the phase velocity of a shear wave propagating in an isotropic medium. The displacements associated with the SV wave in the plate and which may be detected by the noncontact receiving transducer are approximated by an asymptotic solution for an infinite transversely isotropic medium subjected to a harmonic point load.

Liao, Peter↗

NASA NTRS1987

Tectonics of the Nazca-Antarctic plate boundary

A new bathymetric chart of part of the Chile transform system is constructed, based mainly on an R/V Endeavor survey from 100 deg W to its intersection with the East Ridge of the Juan Fernandez microplate. A generally continuous lineated trend can be followed through the entire region, with the transform valley being relatively narrow and well-defined from 109 deg W to approximately 104 deg 30 min W. The fracture zone then widens to the east, with at least two probable en echelon offsets to the south at 104 deg and 102 deg W. Six new strike-slip mechanisms along the Chile Transform and one normal fault mechanism near the northern end of the Chile Rise, inverted together with other plate-motion data from the eastern portion of the boundary, produce a new best-fit Euler pole for the Nazca-Antarctic plate pair, providing tighter constraints on the relative plate motions.

Anderson-Fontana, Sandra↗

NASA NTRS1988

Comparison of boundary-layer transition on a cone and flat plate at Mach 3.5

NASA-Langley's Pilot Low-Disturbance Tunnel has been used to obtain boundary layer transition data on a cone and flat plate at Mach 3.5. The transition Reynolds numbers measured under these low noise conditions are higher than those in conventional noisy tunnels by a factor of 3 in the case of the cone and of seven in that of the flat plate. Transition predictions based on compressible linear stability theory and the e exp N method, for N=10, are in excellent agreement with the measured locations with transition onset for both the cone and flat plate under these low noise conditions.

Chen, F.-J.↗

NASA NTRS1988

Predicting impact induced delaminations in composite plates

A method is presented which can be used to estimate the dimensions of delaminations in fiber reinforced composite plates impacted by a solid object. The impact occurs at low velocity such that the impactor does not penetrate the surface of the plate. Comparisons between measured and calculated delamination lengths and widths are given. The use of the method in the design of impact resistant plates is discussed.

Wu, Hsi-Yung T.↗

NASA NTRS1988

Interference effects on the hypersonic, rarefied flow about a flat plate

The Direct Simulation Monte Carlo method is used to study the hypersonic, rarified flow interference effects on a flat plate caused by nearby surfaces. Calculations focus on shock-boundary-layer and shock-lip interactions in hypersonic inlets. Results are presented for geometries consisting of a flat plate with different leading-edge shapes over a flat lower wall and a blunt-edge flat plate over a 5-degree wedge. The problems simulated correspond to a typical entry flight condition of 7.5 km/s at altitudes of 75 to 90 km. The results show increases in predicted local heating rates for shock-boundary-layer and shock-lip interactions that are quantitatively similar to those observed experimentally at much higher densities.

Wilmoth, Richard G.↗

NASA NTRS1989

High intensity acoustic tests of a thermally stressed aluminum plate in TAFA

An investigation was conducted in the Thermal Acoustic Fatigue Apparatus at the Langley Research Center to study the acoustically excited random motion of an aluminum plate which is buckled due to thermal stresses. The thermal buckling displacements were measured and compared with theory. The general trends of the changes in resonances frequencies and random responses of the plate agree with previous theoretical prediction and experimental results for a mechanically buckled plate.

Ng, Chung Fai↗

NASA NTRS1989

Friction factor data for flat plate tests of smooth and honeycomb surfaces

Friction factors for honeycomb surfaces were measured with a flat plate tester. The flat plate test apparatus was described and a method was discussed for determining the friction factor experimentally. The friction factor model was developed for the flat plate test based on the Fanno Line Flow. The comparisons of the friction factor were plotted for smooth surfaces and six-honeycomb surfaces with three-clearances, 6.9 bar to 17.9 bar range of inlet pressures, and 5,000 to 100,000 range of the Reynolds number. The optimum geometries for the maximum friction factor were found as a function of cell width to cell depth and cell width to clearance ratios.

Ha, Tae Woong↗

NASA NTRS1989

Compression behavior of delaminated composite plates

The response of delaminated composite plates to compressive in-plane loads was investigated. The delaminated region may be either circular or elliptical, and may be located between any two plies of the laminate. For elliptical delaminations, the axes of the ellipse may be arbitrarily oriented with respect to the applied loads. A model was developed that describes the stresses, strains, and deformation of the sublaminate created by the delamination. The mathematical model is based on a two dimensional nonlinear plate theory that includes the effects of transverse shear deformation. The model takes into account thermal and moisture induced strains, transverse pressures acting on the sublaminate, and contact between the sublaminate and plate. The solution technique used is the Ritz method. A computationally efficient computer implementation of the model was developed. The code can be used to predict the nonlinear-load-strain behavior of the sublaminate including the buckling load, postbuckling behavior, and the onset of delamination growth. The accuracy of the code was evaluated by comparing the model results to benchmark analytical solutions. A series of experiments was conducted on Fiberite T300/976 graphite/epoxy laminates bonded to an aluminum honeycomb core forming a sandwich panel. Either circles or ellipses made from Teflon film were embedded in the laminates, simulating the presence of a delamination. Each specimen was loaded in compression and the strain history of the sublaminate was recorded far into the postbuckling regime. The extent of delamination growth was evaluated by C-scan examination of each specimen. The experimental data were compared to code predictions. The code was found to describe the data with reasonable accuracy. A sensitivity study examined the relative importance of various material properties, the delamination dimensions, the contact model, the transverse pressure differential, the critical strain energy release rate, and the relative growth direction on the buckling load, the postbuckling behavior, and the growth load of the sublaminate.

Peck, Scott O.↗

NASA NTRS1988

Line spring model and its applications to part-through crack problems in plates and shells

The line spring model is described and extended to cover the problem of interaction of multiple internal and surface cracks in plates and shells. The shape functions for various related crack geometries obtained from the plane strain solution and the results of some multiple crack problems are presented. The problems considered include coplanar surface cracks on the same or opposite sides of a plate, nonsymmetrically located coplanar internal elliptic cracks, and in a very limited way the surface and corner cracks in a plate of finite width and a surface crack in a cylindrical shell with fixed end.

Erdogan, Fazil↗