Search NASA⌕ Search

SEARCH · Search NASA

Results for “Propellant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Development of a solvent processed insensitive propellant

Two types of low vulnerability propellants are studied which are distinguished by whether the binder is a rubber, such as polyurethane or CTBN, or a plasticizable polymer such as ethyl cellulose or cellulose acetate. The former propellants are made by a partial cure extrusion process while the latter are made by the conventional solvent process. Emphasis is given to a cellulose binder (plasticizer) RDX composition. The type of binder used, the particle size of the RDX and the presence of small quantities of nitrocellulose in the solvent processed compositions have important influences on the mechanical and combustion characteristics of the propellant. The low temperature combustion is of particular concern because of potential breakup of the grains that can lead to instability.

Trask, R.↗

Low and high speed propellers for general aviation: Performance potential and recent wind tunnel test results

The performance of lower speed, 5 foot diameter model general aviation propellers, was tested in the Lewis wind tunnel. Performance was evaluated for various levels of airfoil technology and activity factor. The difference was associated with inadequate modeling of blade and spinner losses for propellers round shank blade designs. Suggested concepts for improvement are: (1) advanced blade shapes (airfoils and sweep); (2) tip devices (proplets); (3) integrated propeller/nacelles; and (4) composites. Several advanced aerodynamic concepts were evaluated in the Lewis wind tunnel. Results show that high propeller performance can be obtained to at least Mach 0.8.

Jeracki, R. J.↗

Outer planet satellite return missions using in situ propellant production

In situ production of oxygen and oxygen with hydrogen for utilization as return propellant from the Galilean satellites has been investigated. Europa has emerged as the preferred landing sight because of the availability of water ice and its surface temperature. When oxygen is used with methane transported from earth, a Europa sample return mission requires 4000 kg less estimated earth launch mass than a vehicle using space storable propellant. Neither methane nor oxygen require active refrigeration at Europa. When oxygen and hydrogen are both utilized to form the primary sample return propellant, the required processor mass increases, but the estimated earth launch mass requirement is reduced by an additional 550 kg.

Ash, R. L.↗

An analytical tool for simulating Large AMplitude Propellant Slosh

The development of a multiple-mass, nonlinear, finite-element analytical model - the Large AMplitude Propellant Slosh model (LAMPS) in two- and three-dimensional versions, is described. The model is used in predicting the forces on the Space Shuttle external tank caused by large amplitude motion of propellant fluid. Comparisons between measured propellant reorientation forces and those predicted by the LAMPS models are presented, and it is concluded that the model provides a cost effective, experimentally verified approach to a complicated nonlinear problem.

Berry, R. L.↗

High temperature propellant development

It is reported that the neccessary technology has been developed and demonstrated for the manufacture of heat-sterilizable solid propellants which meet specific ballistic goals. It is shown that: (1) phosphate doping of ammonium perchlorate significantly enhances the thermal stability of the substance; (2) grinding the ammonium perchlorate to reduce particle size further increases thermal stability; and (3) unsaturated polymers such as the polybutadienes can be successfully used in a heat-sterilizable propellant system. Among the topics considered by the study are oxidizers, dopants, binders, and the thermal cycling of 70 lb and 600 lb propellant grains.

Anderson, F. A.↗

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 1: Unpartitioned Blades

An investigation to determine the effectiveness of icing protection afforded by air-heating hollow steel unpartitioned propeller blades has been conducted In the NACA Cleveland icing research tunnel. The propeller used was a production model modified with blade shank and tip openings to permit internal passage of heated air. Blade-surface and heated-air temperatures were obtained and photographic observations of Ice formations were made with variations In icing intensity and heating rate to the blades. For the conditions of Icing to which the propeller was subjected, it was found that adequate ice protection was afforded with a heating rate of 40 1 000 Btu per hour per blade. With less than 40,000 Btu per hour per blade, ice protection failed because of significant ice accretions on the leading edge. The chordwise distribution of heat was unsatisfactory with most of the available heat dissipated well back of the leading edge on both the thrust and camber face's instead of at the leading edge where it was most needed. A low utilization of available heat for icing protection is indicated by a beat-exchanger effectiveness of approximately 47 percent.

Mulholland, Donald R.↗

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 3: 25% Partitioned Blades

The icing protection obtained from an internally air-heated propeller blade partitioned to confine the heated air forward of 25-percent chord was investigated in the NACA Cleveland icing research tunnel. A production-model hollow steel propeller was modified with an Internal radial partition at 25-percent chord and with shank and tip openings to admit and exhaust the heated air. Temperatures were measured on the blade surfaces and in the heated-air system during tunnel icing conditions. Heat-exchanger effectiveness and photographs of Ice formations on the blades were obtained. Surface temperature measurements indicated that confining the heated air forward of the 25-percent chord gave.a more economical distribution of the applied heat as compared with unpartitioned and 50-percent partitioned blades, by dissipating a greater percentage of the available heat at the leading edge. At a propeller speed of 850 rpm, a heating rate of 7000 Btu per hour per blade at a shank air temperature of 400 F provided adequate Icing protection at ambient-air temperatures of 23 F but not at temperatures as low as 15 F. With the heating rate used, a heat-exchanger effectiveness of 77 percent was obtained as compared to 56 percent for 50-percent partitioned and 47 percent for unpartitioned blades.

Mulholland, Donald R.↗

An Investigation Utilizing an Electrical Analogue of Cyclic Deicing of a Hollow Steel Propeller with an External Blade Shoe

A study has been made of the heat requirement for the cyclic de-icing of hollow steel propellers fitted with external blade heating shoes. Solutions to the equations for the heat flow in cyclic heating of propellers were obtained, using an electrical analogy. The study showed how the energy requirement for propeller de-icing with existing blade shoes could be decreased, and illustrated the effect of blade-shoe design on the energy requirement. It was demonstrated, for example, that by increasing the heating intensity and decreasing the heating period from those currently used the energy requirement could be decreased in the order of 60 percent. ' In addition, ft was shown that heating requirements could be decreased further, by as much as 60 percent, through proper design of the shoes. The' investigation also showed the energy requirement to increase with decreasing liquid-water content and air temperature. Uncertainties as to the exact values of convective heat-transfer coefficient prevailing over the surface of the blade and ice layer resulted in uncertainties of approximately proportional magnitude in the values of required heating intensity.

Neel, Carr B., Jr.↗

Equations for Composite-Propellant Burning

Reported study of composite-propellant burning summarizes recent advances in understanding behavior of propellant formulations based on ammonium perchlorate (AOP), binder, and aluminum in various proportions and particle size distributions. Approach presented incorporates adapted version of earlier model for monopropellant AP. Objective is to predict burning-rate characteristics of composite propellants at high pressure.

Strand, L. D.↗

Finite volume calculation of three-dimensional potential flow around a propeller

The finite volume scheme of Jameson (1977) is used to calculate potential flow around a propeller rotating at high speed. An H-type mesh is generated and used successfully in the calculations. A test calculation with a thick blade cross section shows that the present code is capable of computing the propeller flow at the advance Mach number 0.8. The possible physical mechanisms which may play an important role in the propeller aerodynamics are discussed.

Jou, W.-H.↗

Effect of storable propellants on single-stage earth-to-orbit vehicles

A comparison is made between the storable-propellant engine and an equivalent dual-expander engine using oxygen, propane, and hydrogen propellants. The propane and hydrogen dual-expander engine is then compared with previous results with separate propane and hydrocarbon engines. It is shown that the dual-expander reduces vehicle dry mass from 94 to 89 Mg, or 5%. The hydrogen-only thrust of the dual-expander is 0.4 MN, while the separate hydrogen engines have a thrust of 2.3 MN. The low thrust level increases the difficulty of cooling the dual-expander engine, and additional hydrogen flow is added for transpirational cooling. This additional hydrogen flow leads to an increase in the hydrogen tank size. It is also shown that storable propellants increase the dry mass of single-stage earth-to-orbit vehicles by about 20% and the gross mass by about 54%. It is concluded that dual-expander engines should be studied with several thrust splits and thrust levels.

Martin, J. A.↗

Small transport aircraft technology propeller study

A study to define potential benefits of advanced technology propeller for 1985-1990 STAT commuter airplanes was completed. Two baselines, a Convair, 30 passenger, 0.47 Mach number airplane and a Lockheed, 50 passenger, 0.70 Mach number airplane, were selected from NASA-Ames sponsored airframe contracts. Parametric performance, noise level, weight and cost trends for propellers with varying number of blades, activity factor, camber and diameter incorporating blade sweep, tip proplets, advanced composite materials, advanced airfoils, advanced prevision synchrophasing and counter-rotation are presented. The resulting DOC, fuel burned, empty weight and acquisition cost benefits are presented for resizings of the two baseline airplanes. Six-bladed propeller having advanced composite blades, advanced airfoils, tip proplets and advanced prevision synchrophasers provided the maximum DOC improvements for both airplanes. DOC and fuel burned were reduced by 8.3% and 17.0% respectively for the Convair airplane and by 24.9% and 41.2% respectively for the Lockheed airplane. The larger reductions arose from a baseline definition with very heavy fuselage acoustic treatment. An alternate baseline, with a cabin noise 13dB in excess of the objective, was also studied.

Black, B. M.↗

Aerodynamic evaluation of circulation control propellers

The aerodynamic compatibility of fixed-pitch circulation-control (CC) propellers with the performance characteristics and requirements of a 1600 kg (3600 lb) single-engine variable-pitch propeller general aviation airplane was evaluated. The initial results with elliptical-shaped CC airfoils indicated that the feasibility of application to fixed-pitch propellers was doubtful for the class of airplane investigated (cruise speed of about 300 km/hr) and improbable for higher-speed airplanes. Supplemental data for a cambered circulation-control supercritical airfoil, which became available after completion of the initial evaluation, were subsequently analyzed and are included in the Addendum to this report. With the much superior aerodynamic characteristics of the CC-supercritical airfoil, elimination of variable pitch appears aerodynamically feasible for low-speed airplanes through the use of a moderate amount of upper-surface blowing near the trailing edge during cruise. Overall feasibility depends upon results of structural and systems-type analyses.

Braslow, A. L.↗

In-flight acoustic test results for the SR-2 and SR-3 advanced-design propellers

Several advanced-design propellers, previously tested in the wind tunnel at the Lewis Research Center, have been tested in flight at the Dryden Flight Research Facility. The flight-test propellers were mounted on a pylon on the top of the fuselage of a JetStar airplane. Acoustic data for the advanced-design SR-2 and SR-3 propellers at Mach numbers to 0.8 and helical-tip Mach numbers to 1.15 are presented; maximum blade-passage frequency sound-pressure levels are also compared.

Lasagna, P. L.↗

Propeller Design Program

Planform and propeller twist with minimum induced loss calculated. New Theoretical treatment combines classical theories of Betz-Prandtl, Goldstein, and Glauert easily applied to problem of determining propeller blade geometry for minimum induced loss. Analysis applicable at subsonic flight speeds and neglects structural considerations in propeller design.

Phillips, W. H.↗

Aeroelastic analysis for propellers - mathematical formulations and program user's manual

Mathematical development is presented for a specialized propeller dedicated version of the G400 rotor aeroelastic analysis. The G400PROP analysis simulates aeroelastic characteristics particular to propellers such as structural sweep, aerodynamic sweep and high subsonic unsteady airloads (both stalled and unstalled). Formulations are presented for these expanded propeller related methodologies. Results of limited application of the analysis to realistic blade configurations and operating conditions which include stable and unstable stall flutter test conditions are given. Sections included for enhanced program user efficiency and expanded utilization include descriptions of: (1) the structuring of the G400PROP FORTRAN coding; (2) the required input data; and (3) the output results. General information to facilitate operation and improve efficiency is also provided.

Bielawa, R. L.↗

A possible explanation for the present difference between linear noise theory and experimental data for supersonic helical tip speed propellers

High speed turboprops are attractive candidates for future aircraft because of their high propulsive efficiency. However, the noise of their propellers may create a cabin environment problem for the aircraft powered by these propellers. The noise of some propeller models was measured, and predictions of the noise using a method based on the Ffowcs Williams-Hawkins equation were made. The predictions and data agree well at lower helical tip Mach numbers but deviate above Mach 1.0. Some possible reasons why the theory does not predict the data and focuses on improvement of the aerodynamic inputs as the most likely remedy are investigated. In particular, it is proposed that an increase in the drag and a decrease in the lift near the tip of the blade where the majority of the noise is generated, is warranted in the input to the theory.

Dittmar, J. H.↗

An experimental investigation of the effect of boundary layer refraction on the noise from a high-speed propeller

Models of supersonic propellers were previously tested for acoustics in the Lewis 8- by 6-Foot Wind Tunnel using pressure transducers mounted in the tunnel ceiling. The boundary layer on the tunnel ceiling is believed to refract some of the propeller noise away from the measurement transducers. Measurements were made on a plate installed in the wind tunnel which had a thinner boundary layer than the ceiling boundary layer. The plate was installed in two locations for comparison with tunnel ceiling noise data and with fuselage data taken on the NASA Dryden Jetstar airplane. Analysis of the data indicates that the refraction increases with: increasing boundary layer thickness; increasing free stream Mach number; increasing frequency; and decreasing sound radiation angle (toward the inlet axis). At aft radiation angles greater than about 100 deg there was little or no refraction. Comparisons with the airplane data indicated that not only is the boundary layer thickness important but also the shape of the velocity profile. Comparisons with an existing two-dimensional theory, using an idealized shear layer to approximate the boundary layer, showed that the theory and data had the same trends. Analysis of the data taken in the tunnel at two different distances from the propeller indicates a decay with distance in the wind tunnel at high Mach numbers but the decay at low Mach numbers is not as clear.

Dittmar, J. H.↗