Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Measurement and prediction of through-section residual stresses in the manufacturing sequence of bearing components

Through-section residual stresses in an asymmetric, thin-walled tapered bearing component were non-destructively studied via neutron diffraction after soft machining, heat treatment and hard turning. Two-dimensional area maps revealed non-uniform distributions of stress fields in both the thinnest and thickest sections of the component, indicating that the entire processing sequence plays a vital role — not only in distortion, but in the final stress state as well. Here, a computational model was developed to further understand the extent of the distortion induced in bearing components as a result of process variables in the manufacturing sequence.

36 MATERIALS SCIENCE↗

Residual Stress Mapping of As-Built and Hot Isostatic Pressure Treated GRCop-84 as Fabricated by Selective Laser Melting

GRCop-84, a copper alloy developed by NASA Glenn Research Center (GRC) with the starting At% (atomic percent) Cu-8 Cr-4 Nb, has a copper matrix with a fine intermetallic dispersion of Cr2Nb (cubic Laves phase C15). The alloy is being developed for high-heat-flux applications and has excellent high temperature properties including retention of tensile strength at high temperatures, high thermal conductivity, and excellent creep resistance. GRCop-84 has shown higher survivability rates than other metal additive alloys, good surface finish, and requires less operator tweaking for builds, and this is not fully understood. Neutron diffraction provides an accurate, non-destructive method of measuring the thermal stresses accumulated during production; the primary source of failure before annealing. The unstressed lattice spacing (d (sub 0)), residual stress, and distribution have been characterized for simple shapes in HIP (Hot Isostatic Pressing,) and as-built conditions made with SLM (Selective Laser Melting), a powder bed fusion method, with the HIP samples showing significantly reduced stresses concentrations than the as-built.

Minnecci, Robert↗

Misfit dislocation gettering by substrate pit-patterning in SiGe films on Si(001)

We show that suitable pit-patterning of a Si(001) substrate can strongly influence the nucleation and the propagation of dislocations during epitaxial deposition of Si-rich Si{sub 1-x}Ge{sub x} alloys, preferentially gettering misfit segments along pit rows. In particular, for a 250 nm layer deposited by molecular beam epitaxy at x{sub Ge} = 15%, extended film regions appear free of dislocations, by atomic force microscopy, as confirmed by transmission electron microscopy sampling. This result is quite general, as explained by dislocation dynamics simulations, which reveal the key role of the inhomogeneous distribution in stress produced by the pit-patterning.

36 MATERIALS SCIENCE↗

Structures and Zonal Flows in Magnetized Plasmas

The numerical study of the zonal flows (transport barriers) in the drift-wave turbulence in magnetically confined plasmas is presented. The existence of two distinct mechanisms for their generation is demonstrated. The evolution of a drift wave-zonal flow system, nonlinearly coupled via the Reynolds stress, is described by a nonlinear equation for the slowly varying envelope of the drift waves, and the nonlinear dispersion relation for the modulational instability of a drift wave pump is derived and analyzed. First, an arbitrary spatial distribution of strictly poloidally propagating drift waves is shown to rapidly decay into the array of localized soliton-like structures moving with different speeds. The corresponding zonal flow potential evolves into the sequence of shocks that produces a strong shearing, with many alternating plasma flows. Next, it is demonstrated that the coherent dipolar vortices, that constitute the building blocks of the strong drift-wave turbulence, are unstable in the presence of an electron temperature gradient. The dipolar vortices (or modons) undergo a qualitative modification by the action of the scalar nonlinearity arising from the magnetic {beta} effect. The modons propagating in the direction of the electron diamagnetic drift rapidly topple, disintegrating into two monopoles that propagate independently and rapidly disperse. Conversely, for the modons that initially moved in the direction of the ion diamagnetic drift, the {beta}-effect produces the change of the direction of the propagation, followed by the stretching in the poloidal direction. On a long time scale, such modons expand to a length equal to the size of the computational box, and essentially an one-dimensional zonal flow is created, whose transverse scale is determined by the initial modon size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shear-Sensitive Liquid Crystal Coating Method Applied Through Transparent Test Surfaces

Research conducted at NASA Ames Research Center has shown that the color-change response of a shear-sensitive liquid crystal coating (SSLCC) to aerodynamic shear depends on both the magnitude of the local shear vector and its direction relative to the observer's in-plane line of sight. In conventional applications, the surface of the SSLCC exposed to aerodynamic shear is illuminated with white light from the normal direction and observed from an oblique above-plane view angle of order 30 deg. In this top-light/top-view mode, shear vectors with components directed away from the observer cause the SSLCC to exhibit color-change responses. At any surface point, the maximum color change (measured from the no-shear red or orange color) always occurs when the local vector is aligned with, and directed away from, the observer. The magnitude of the color change at this vector-observer-aligned orientation scales directly with shear stress magnitude. Conversely, any surface point exposed to a shear vector with a component directed toward the observer exhibits a non-color-change response, always characterized by a rusty-red or brown color, independent of both shear magnitude and direction. These unique, highly directional color-change responses of SSLCCs to aerodynamic shear allow for the full-surface visualization and measurement of continuous shear stress vector distributions. The objective of the present research was to investigate application of the SSLCC method through a transparent test surface. In this new back-light/back-view mode, the exposed surface of the SSLCC would be subjected to aerodynamic shear stress while the contact surface between the SSLCC and the solid, transparent wall would be illuminated and viewed in the same geometrical arrangement as applied in conventional applications. It was unknown at the outset whether or not color-change responses would be observable from the contact surface of the SSLCC, and, if seen, how these color-change responses might relate to those observed in standard practice.

Reda, Daniel C.↗

Distributed measurement of minimum and maximum in-situ stress in substrates

A system for performing distributed measurements of in-situ stress includes an expandable element with at least one fiber optic sensor. The expandable element can be positioned at various depths in a hole in a substrate. A pressurizing device expands (and contracts) the expandable element when the expandable element is inserted in the hole in the substrate to exert pressure on the hole wall. A pressure sensor provides a sensor output indicative of a pressure applied to the hole wall by the expandable element. The fiber optic sensor and an optical interrogator measure strain along a length of the sensor in a continuous, high spatial resolution manner Based on the measured strain and pressure sensor output, the system determines various properties of the substrate such as, minimum principal stress, maximum principal stress, and/or principal stress direction associated with one or more fractures in the substrate, as well as substrate modulus.

Ohanian, III, Osgar John↗

Stress field and interaction forces between dislocations and precipitate distributions

A computational method is developed for calculation of the stress field and interaction forces between dislocations and precipitates of arbitrary shape and distribution. The internal stress generated by precipitates due to coherency strain is implemented within the discrete dislocation dynamics (DDD) framework. The s-version finite element method (s-FEM), which models a precipitate of arbitrary shape using a local mesh is used to calculate coherency stress fields. The method facilitates meshing precipitate volumes of arbitrary geometry, and multiple local meshes can be superimposed at various positions of the global mesh. Accuracy and convergence conditions of the method are established. For a single precipiate, the method is shown to be 3.5 times faster than a standard FEM calculation for the same accuracy, and the gain in speed increases with the number of precipitates. The CRSS of spherical precipitates is found to be higher than disk-shaped precipitates of the same volume fraction.

42 ENGINEERING↗

The influences of fluorine and process variations on polysilicon film stress and MOSFET hot carrier effects

The use of fluorinated gate oxides may provide an improvement in nMOSFET reliability by enhancing hot carrier resistance. In order to clarify the mechanisms by which polysilicon processing and fluorination influence the oxide behavior, a matrix of nMOSFET structures was prepared using various processing, doping, and implantation strategies. These structures were evaluated for crystalline morphology and chemical element distribution. Mechanical stress measurements were taken on the polysilicon films from room temperature to cryogenic temperature. These examinations showed that fluorination of a structure with randomly oriented polysilicon can reduce residual mechanical stress and improve hot carrier resistance at room temperature.

Lowry, Lynn E.↗

Neutron measurements of stresses in a test artifact produced by laser-based additive manufacturing

A stainless steel test artifact produced by Direct Metal Laser Sintering and similar to a proposed standardized test artifact was examined using neutron diffraction. The artifact contained a number of structures with different aspect ratios pertaining to wall thickness, height above base plate, and side length. Through spatial resolutions of the order of one millimeter the volumetric distribution of stresses in several was measured. It was found that the stresses peak in the tensile region around 500 MPa near the top surface, with balancing compressive stresses in the interior. The presence of a support structure (a one millimeter high, thin walled, hence weaker, lattice structure deposited on the base plate, followed by a fully dense AM structure) has only minor effects on the stresses.

36 MATERIALS SCIENCE↗

3-D laser anemometer measurements in a labyrinth seal

The flow field inside a seven cavity labyrinth seal with a 0.00127 m clearance was measured using a 3-D laser Doppler anemometer system. Through the use of this system, the mean velocity vector and the entire Reynolds stress tensor distributions were measured for the first, third, fifth, and seventh cavities of the seal. There was one large recirculation region present in the cavity for the flow condition tested, Re = 28,000 and Ta = 7,000. The axial and radial mean velocities as well as all of the Reynolds stress term became cavity independent by the third cavity. The azimuthal mean velocity varied from cavity to cavity with its magnitude increasing as the flow progressed downstream.

Morrison, G. L.↗

Bidisperse supension balance model

The suspension balance model (SBM) for viscous Stokes flow has been well studied for the case of identical, monodisperse spherical particles in a channel, however, more work remains to be done to explore the bidisperse and polydisperse SBM. Here, we present a simple extension of the SBM that allows for modeling of suspensions of particles of bidisperse size. The comparison with avaiable experiments and direct simulations is found to be good. Additionally, we present a range of simulations to justify the assumptions made in the polydisperse suspension balance model for non-Brownian, neutrally buoyant particles that vary in size with a bidisperse distribution. The aim is to study the effects of moderate size variation on the rheology of the suspension and the distribution of the particles across the flow, especially in the near-wall regions. It is shown that, at the size ratios considered, bidispersity in the particle size does not significantly affect rheological parameters including the particle volume fraction and relative viscosity in the bulk of a Couette flow. The particle phase stresses are distributed between small and large particles in proportion to the relative volume fractions of each species. In bidisperse suspensions, the large particles in the wall layer develop a spatial structure and form chains in the streamwise direction.

97 MATHEMATICS AND COMPUTING↗

Influence of Asymmetric Cyclic Loading on Structural Evolution and Deformation Behavior of Cu-5 at.% Zr Alloy: An Atomistic Simulation-Based Study

Molecular dynamics (MD) simulation-based studies of tensile test and structural evolution of Cu-5 at.% Zr alloy under asymmetric cyclic loading (i.e., ratcheting behavior) considering various stress ratios such as − 0.2, − 0.4 and − 0.6 for different temperatures, viz.≈ 100, 300 and 500 K have been performed using embedded atom model Finnis–Sinclair potential. According to obtained stress–strain response from MD calculation, Cu-5 at.% Zr alloy specimen is pristine in nature as sudden drop in stress just after yield stress and subsequent elastic type deformation are observed for this alloy. Predicted ratcheting strain by MD simulation for Cu-5 at.% Zr alloy varies from 4.5 to 5%. Significant increase in ratcheting strain has been observed with the increase in temperature. Slight reduction in crystallinity is identified at the middle of the each loading cycle from the performed radial distribution function analysis and cluster analysis.

36 MATERIALS SCIENCE↗

Determination of the Fracture Parameters in a Stiffened Composite Panel

A modified J-integral, namely the equivalent domain integral, is derived for a three-dimensional anisotropic cracked solid to evaluate the stress intensity factor along the crack front using the finite element method. Based on the equivalent domain integral method with auxiliary fields, an interaction integral is also derived to extract the second fracture parameter, the T-stress, from the finite element results. The auxiliary fields are the two-dimensional plane strain solutions of monoclinic materials with the plane of symmetry at x(sub 3) = 0 under point loads applied at the crack tip. These solutions are expressed in a compact form based on the Stroh formalism. Both integrals can be implemented into a single numerical procedure to determine the distributions of stress intensity factor and T-stress components, T11, T13, and thus T33, along a three-dimensional crack front. The effects of plate thickness and crack length on the variation of the stress intensity factor and T-stresses through the thickness are investigated in detail for through-thickness center-cracked plates (isotropic and orthotropic) and orthotropic stiffened panels under pure mode-I loading conditions. For all the cases studied, T11 remains negative. For plates with the same dimensions, a larger size of crack yields larger magnitude of the normalized stress intensity factor and normalized T-stresses. The results in orthotropic stiffened panels exhibit an opposite trend in general. As expected, for the thicker panels, the fracture parameters evaluated through the thickness, except the region near the free surfaces, approach two-dimensional plane strain solutions. In summary, the numerical methods presented in this research demonstrate their high computational effectiveness and good numerical accuracy in extracting these fracture parameters from the finite element results in three-dimensional cracked solids.

Lin, Chung-Yi↗

Two-Dimensional Problem of Thermoelasticity for a Half Space in the Presence of Heat Release in a Ribbon-Shaped Domain Parallel to its Boundary

Using a logarithmic single-layer potential, thermoelastic displacement potential, Airy stress function, and Boussinesq function, we solve two-dimensional problems of stationary heat conduction and thermoelasticity under the conditions of plane deformation of a semiinfinite body in the presence of heat release in a ribbon-shaped domain parallel to its boundary (in this domain, either a temperature or a heat flux is given). The boundary of the body is kept at temperature equal to zero. We study the distribution of stresses in the domain of heat release with given heat sources of constant intensity at constant temperature.

42 ENGINEERING↗

A Novel Approach for Bounding the Stress Experienced by the Core of Utility-Scale Printed Circuit Heat Exchangers Under Thermohydraulic Loads

Printed circuit heat exchangers (PCHEs) have rapidly gained popularity since being introduced nearly three decades ago, and they are currently widely deployed in the petrochemical and aviation industry. Their compactness, thermohydraulic efficiency, inherent suitability for high temperature/pressure fluids containment, and demonstrated durability are some of the reasons the nuclear industry is seeking to adopt this technology as well. However, the relatively strict nuclear-related regulatory design code, especially when classified as critical to the safety of the reactors, is posing challenges to adopting the technology. From stress analysis point of view, one undesirable feature of PCHEs is their geometrical complexity, which is implied by their multilength-scale features. As a result, a full-scale model of a utility-scale exchanger cannot simply be solved on a computer because meshing such components results in a vast number of degrees-of-freedom. Here, this work seeks to address the challenge of stress analyses to PCHEs by presenting a method to simplify the geometry of PCHE designs. The models proposed by this work can be practically analyzed on a standard computer and provide a path for implementing ASME design rules. The analyses presented herein are divided into five separate investigations. Each is carried out to incrementally simplify the analyzed model by addressing features such as the shapes of the flow passages, the complex distribution of stress in large components, the three-dimensionality of the stress and strain, the thermal stresses caused by thermohydraulic operation observed experimentally and more.

42 ENGINEERING↗

Finite element solutions for crack-tip behavior in small-scale yielding

The subject considered is the stress and deformation fields in a cracked elastic-plastic power law hardening material under plane strain tensile loading. An incremental plasticity finite element formulation is developed for accurate analysis of the complete field problem including the extensively deformed near tip region, the elastic-plastic region, and the remote elastic region. The formulation has general applicability and was used to solve the small scale yielding problem for a set of material hardening exponents. Distributions of stress, strain, and crack opening displacement at the crack tip and through the elastic-plastic zone are presented as a function of the elastic stress intensity factor and material properties.

Tracey, D. M.↗

Stress-Dependent Matrix Cracking in 2D Woven SiC-Fiber Reinforced Melt-Infiltrated SiC Matrix Composites

The matrix cracking of a variety of SiC/SiC composites has been characterized for a wide range of constituent variation. These composites were fabricated by the 2-dimensional lay-up of 0/90 five-harness satin fabric consisting of Sylramic fiber tows that were then chemical vapor infiltrated (CVI) with BN, CVI with SiC, slurry infiltrated with SiC particles followed by molten infiltration of Si. The composites varied in number of plies, the number of tows per length, thickness, and the size of the tows. This resulted in composites with a fiber volume fraction in the loading direction that ranged from 0.12 to 0.20. Matrix cracking was monitored with modal acoustic emission in order to estimate the stress-dependent distribution of matrix cracks. It was found that the general matrix crack properties of this system could be fairly well characterized by assuming that no matrix cracks originated in the load-bearing fiber, interphase, chemical vapor infiltrated Sic tow-minicomposites, i.e., all matrix cracks originate in the 90 degree tow-minicomposites or the large unreinforced Sic-Si matrix regions. Also, it was determined that the larger tow size composites had a much narrower stress range for matrix cracking compared to the standard tow size composites.

Morscher, Gregory N.↗