Search NASA⌕ Search

SEARCH · Search NASA

Results for “cathode coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Mechanically and Chemically Robust Sandwich-Structured C@Si@C Nanotube Array Li-Ion Battery Anodes

Stability and high energy densities are essential qualities for emerging battery electrodes. Because of its high specific capacity, silicon has been considered a promising anode candidate. However, the several-fold volume changes during lithiation and delithiation leads to fractures and continuous formation of an unstable solid-electrolyte interphase (SEI) layer, resulting in rapid capacity decay. Here, we present a carbon–silicon–carbon (C@Si@C) nanotube sandwich structure that addresses the mechanical and chemical stability issues commonly associated with Si anodes. The C@Si@C nanotube array exhibits a capacity of ~2200 mAh g –1 (~750 mAh cm –3 ), which significantly exceeds that of a commercial graphite anode, and a nearly constant Coulombic efficiency of ~98% over 60 cycles. In addition, the C@Si@C nanotube array gives much better capacity and structure stability compared to the Si nanotubes without carbon coatings, the ZnO@C@Si@C nanorods, a Si thin film on Ni foam, and C@Si and Si@C nanotubes. In situ SEM during cycling shows that the tubes expand both inward and outward upon lithiation, as well as elongate, and then revert back to their initial size and shape after delithiation, suggesting stability during volume changes. The mechanical modeling indicates the overall plastic strain in a nanotube is much less than in a nanorod, which may significantly reduce low-cycle fatigue. Furthermore, the sandwich-structured nanotube design is quite general, and may serve as a guide for many emerging anode and cathode systems.

25 ENERGY STORAGE↗

Evaluation residual moisture in lithium-ion battery electrodes and its effect on electrode performance

Removing residual moisture in lithium-ion battery electrodes is essential for desired electrochemical performance. In this manuscript, the residual moisture in LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathodes produced by conventional solvent-based and aqueous processing is characterized and compared. The electrochemical performance has also been investigated for various residual moisture contents. As a result, it has been demonstrated that the residual moisture lowers the first cycle coulombic efficiency, but its effect on short term cycle life is insignificant.

25 ENERGY STORAGE↗

Spark Breakdown Threshold in Non-Uniform Fields

We develop a criterion for spark breakdown in non-uniform field geometries with positive polarity and small electrode separations so that breakdown evolves without the formation of a leader. We arrive at the spark-breakdown criterion by framing it in terms of gain and instability conditions, whose relative importance are established from an analysis of the experimental breakdown characteristics and correlations with streamer behavior in short gaps. Results are presented in the context of two generic geometries having coaxial and point-plane electrodes. For nearly uniform field situations, we re-confirm that the breakdown criterion obtained by the usual extension of either the Townsend or Meek criteria satisfactorily predicts the experimental results. On the other hand, for increasing non-uniformity, the results for the corona and spark branches of the breakdown characteristics are shown inconsistent with a breakdown criterion solely based on either the Townsend or streamer mechanisms. In particular, the avalanche gain factor, the primary component of the Townsend and streamer criteria does not determine the spark breakdown criterion. Streamers can cross the gap for a significantly wide range of applied voltages without triggering a spark. We find that it is the instability condition, derived from a relation between the minimum Laplacian field in the gap and the local streamer body field (which we relate to the streamer sustaining field), that is sufficient for determining the spark threshold thereby yielding a breakdown criterion. We examine the physics of the discharge occurring in the several parts of the nonuniform field gap to elucidate the underpinning of the threshold criterion. These include streamer stability and branching in the stressed electrode region, cathode fall setup near the planar-type electrode, and importantly, the renewed ionization of the discharge resulting from neutral expansion of the gas discharge driven by currents, which are critically dependent on the minimum field level in the gap. We also discuss experiments which were carried out to examine instabilities associated with the streamer breakdown of uniform gaps with triggering.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hollow-cathode chemical vapor deposition of thick, low-stress diamond-like carbon films

A radio-frequency (RF), hollow-cathode plasma source with confining magnetic field is described for the chemical vapor deposition of thick ( > 10 µm), amorphous diamond-like carbon ablator films for inertial confinement fusion applications. Plasma is characterized by optical emission spectroscopy, while properties of the resultant films are measured by a combination of profilometry, Rutherford backscattering spectrometry, elastic recoil detection analysis, X-ray diffraction, Raman spectroscopy, and atomic force microscopy. The dependence of the deposition rate, film density, elemental composition, self-bias and residual stress is reported as a function of RF power. Higher density films were found when using Ar plasma, than N 2 or H 2 plasma. The coatings produced are x-ray amorphous, exhibit low compressive stress ( ~ 100 MPa), high density ( < 1.7 g/cm 3 ), hydrogen content of ~ 30 at.%, and a low average roughness of 0.75 nm. Finally, applications of these films as tunable-density ablators for inertial confinement fusion experiments are discussed.

36 MATERIALS SCIENCE↗

Robust Large-Scale Dynamic Windows using Reversible Metal Electrodeposition

This project funded the study and development of dynamic windows based on reversible metal electrodeposition (RME). Dynamic windows allow user control over light and heat flow into and out of buildings, which offer both advantages in building aesthetics (with worker productivity improvement of 2%) and energy efficiency (up to 20% savings) compared to static controls such as low emissivity coatings and blinds/shades. Despite these advantages, dynamic windows, which traditionally rely on electrochromic metal oxides or conductive organic molecules for light modulation have failed to significantly impact the market due to issues related to cost, color, and optical dynamic range. Dynamic windows based on reversible metal electrodeposition (RME) are an exciting alternative approach and have the potential to overcome the issues associated with traditional technologies. A RME dynamic window is an electrochemical cell that modulates light using the reversible electrodeposition of metal on and off a transparent conducting oxide (TCO), which serves as the working electrode. The electrolyte has nearly colorless metal salts dissolved, and application of a cathodic potential on the TCO reduces the metal cations across the TCO surface to their metallic form, making a thin film that is efficient at blocking out light. A reverse in polarity oxidizes the metal, where it dissolves into solution, returning the window back to transparent. The counter electrode typically employed is a metal mesh, which is used to balance the electrochemical reactions happening on the TCO working electrode. These RME dynamic windows have the largest dynamic range (capable of reaching <<0.1% transmission) with color neutral tinting of any existing technology using solution processed techniques, which positions the technology as a promising candidate to penetrate the residential market. We have successfully scaled up the windows from 25 cm2 to 929 cm 2 , and we have demonstrated significant improvements to both the cycle life (10,000 cycles in a 3-electrode half-cell) and shelf life (>1 month) of our windows. We have published our work in high impact journals (6 published and 2 manuscripts in prep), filed 5 patents, and have incorporated TYNT Technologies to commercialize the technology.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Direct Air Capture-Compatible Azolate and Amino Acid Ionic Liquids for Electrochemical CO 2 Reduction to CO on a Silver Cathode

Direct air capture (DAC) compatible ionic liquids (ILs) are attractive for integrating CO 2 capture and conversion due to their high CO 2 solubility at low partial pressures, tunable chemisorption mechanisms, low volatility, and wide electrochemical windows. However, very few ILs have high CO 2 uptake at DAC conditions (420 ppm CO 2 ), and even fewer have been evaluated for chemical compatibility and mechanistic continuity for combined capture and electrochemical CO 2 reduction (eCO 2 RR). We demonstrate that two representative DAC-capable ILs, [P 4444 ][Val] (amino acid-based) and [P 66614 ][5-Me-Imd] (azolate-based), exhibit favorable electrochemical reduction behavior. CO and H 2 were the dominant gas-phase products by GC, while 1 H and 13 C NMR confirmed negligible liquid-phase HCOOH. Chronoamperometry at moderate applied potentials (−2.0 to −2.5 V vs Ag/AgCl) in a two-compartment H-cell with a Ag coated carbon paper as the working electrode yielded steady-state current densities of ∼10 mA cm −2 with CO FE of 96% for [P 4444 ][Val] and 95% for [P 66614 ][5-Me-Imd], highlighting the role of viscosity and chemically absorbed CO 2 -IL species to provide highly selective CO formation while suppressing H 2 evolution.

amino acid ionic liquid↗

Electrospun Nanofiber Electrodes for High and Low Humidity PEMFC Operation

MEAs with nanofiber mat electrodes containing Pt/C catalyst and Nafion binder were fabricated and evaluated. The electrodes were prepared by electrospinning a solution of catalyst powder, salt-form Nafion (with Na + , Li + , or Cs + as the sulfonic acid counterion), and a carrier polymer of either polyethylene oxide or poly(acrylic acid). The carrier polymer was extracted prior to MEA testing by a hot water soaking step. The resulting fibers were 15%–17% porous, with a core–shell-like morphology (a coating of primarily Nafion on the fiber surface). MEAs with anode/cathode catalyst loadings of 0.1 mg Pt cm −2 each and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions in H 2 /air fuel cell tests, e.g., a maximum power density of 919 mW cm −2 at 100% RH and 832 mW cm −2 at 40% RH for a test at 80 °C and 200 kPa abs . The presence of nm-size pores within the fibers trapped water via capillary condensation during low RH feed gas testing, thus maintaining a high proton conductivity of the Nafion binder in the anode and cathode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder.

25 ENERGY STORAGE↗

Performance characteristics of high-conductivity channel electron multipliers

The paper describes a new type of continuous channel multiplier (CEM) fabricated from a low-resistance glass to produce a high-conductivity channel section and thereby obtain a high count-rate capability. The flat-cone cathode configuration of the CEM is specifically designed for the detection of astigmatic exit images from grazing-incidence spectrometers at the optimum angle of illumination for high detection efficiencies at XUV wavelengths. Typical operating voltages are in the range of 2500-2900 V with stable counting plateau slopes in the range 3-6% per 100-V increment. The modal gain at 2800 V was typically in the range (50-80) million. The modal gain falls off at count rates in excess of about 20,000 per sec. The detection efficiency remains essentially constant to count rates in excess of 2 million per sec. Higher detection efficiencies (better than 20%) are obtained by coating the CEM with MgF2. In life tests of coated CEMs, no measurable change in detection efficiency was measured to a total accumulated signal of 2 times 10 to the 11th power counts.

Timothy, J. G.↗

Atomically dispersed iron sites with a nitrogen–carbon coating as highly active and durable oxygen reduction catalysts for fuel cells

Nitrogen-coordinated single atom iron sites (FeN 4 ) embedded in carbon (Fe–N–C) are the most active platinum group metal-free oxygen reduction catalysts for proton-exchange membrane fuel cells. Still, current Fe–N–C catalysts lack sufficient long-term durability and are not yet viable for practical applications. Here we report a highly durable and active Fe–N–C catalyst synthesized using heat treatment with ammonia chloride followed by high-temperature deposition of a thin layer of nitrogen-doped carbon on the catalyst surface. We propose that catalyst stability is improved by converting defect-rich pyrrolic N-coordinated FeN 4 sites into highly stable pyridinic N-coordinated FeN 4 sites. The stability enhancement is demonstrated in membrane electrode assemblies using accelerated stress testing and a long-term steady-state test (>300 h at 0.67 V), approaching a typical Pt/C cathode (0.1 mg Pt cm -2 ). The encouraging stability improvement represents a critical step in developing viable Fe–N–C catalysts to overcome the cost barriers of hydrogen fuel cells for numerous applications.

08 HYDROGEN↗

Nb3Sn thin films grown using energetic condensation for SRF applications

The traditional method used to coat thin films of Nb3Sn onto SRF cavities has been to start with a Nb cavity and dip it into molten Sn. At high temperatures (>1100 °C), the Sn diffuses into the Nb to create a stoichiometrically correct film1,2 that offers superconducting properties. Here we describe a lower-temperature process that uses two separate plasmas of Nb and Sn to fire 50-150eV ions of Nb and Sn at a substrate that is heated to <400 °C. The non-equilibrium energetic condensation of Nb and Sn ions via subplantation3 creates a high crystal quality film of Nb3Sn. The stoichiometry of this film is controlled by adjusting the currents to the two separate cathodes that in turn controls the ion fluxes to the substrate. EDX, Tc, RRR and other measurements show that this method enables growth of superconducting films even on relatively low temperature substrates. This approach might offer a path to creating higher temperature Cu SRF cavities of the future that might reduce materials and cryogenics costs. 1 G. Arnolds-Mayer, Proc. SRF2, Geneva, Switzerland, pp. 643-666, 1984 2 Sam Posen, Matthias Liepe, Yi Xie, N. Valles, Proceedings of Thin Films Workshop, Padua Italy, October 2010 3 M. Krishnan et al., Superconductor Science and Technology, vol. 24, no. 11, p. 115002, Nov. 2011

James, C.↗

Ultralow content of Pt on Pd–Co–Cu/C ternary nanoparticles with excellent electrocatalytic activity and durability for the oxygen reduction reaction

Optimizing the utilization of Pt to catalyze the sluggish kinetics of the oxygen reduction reaction (ORR) is of vital importance in proton exchange membrane fuel cells. One of the strategies is to spread Pt atoms over the surface of a substrate to increase the surface area. We report a facile method to synthesize Pd6CoCu@Pt/C core-shell nanoparticles with an ultralow amount of Pt. It was found that Pt-coated layer on Pd6CoCu cores plays a vital role in enhancing the ORR activity and the cycling stability. The half-wave potential of Pd6CoCu@Pt/C positively shifts about 50 mV and 17 mV relative to Pd6CoCu/C and Pt/C, respectively. The Pt mass activity on Pd6CoCu@Pt/C was calculated to be about 27 times higher than that on Pt/C catalysts at 0.9 V. Furthermore, the Pd6CoCu@Pt/C nanoparticles exhibit superior stability with almost no decay for the ORR polarization curves during 10,000 potential cycles and the core-shell structure remains with only a slight increase in the thickness of the Pt overlayer. Our findings provide a methodology for synthesizing highly efficient catalytic materials for the cathodic application in fuel cells.

36 MATERIALS SCIENCE↗

Directing High-Efficiency Na Plating with Carbon–Aluminum Junction Interfaces for Anode-Free Na Metal Batteries

Anode-free sodium metal batteries are highly promising for future energy storage but suffer from much faster cycling degradation as they are sensitive to even trace levels of irreversible side reactions. This work focuses on the most practical Al foil current collectors and systematically examined the effect of nano-sized carbon coating on improving the Na plating and stripping stability. We identified that the carbon-Al junction interface generated by carbon coating enabled more uniform Na depositing with lower overpotentials, delivering higher than 99.8% Faradaic efficiencies for a wide range of cycling currents between 0.5 and 3.0 mA cm -2 . This performance is much better than the 96.4% efficiency observed on uncoated Al foils under the same conditions, and was also confirmed under lean electrolyte and freezing electrolyte conditions, and can be attributed to the stronger interfacial binding and enhanced sodiophilic properties of the carbon-aluminum junction sites. Furthermore, these sites not only ensure uniform Na plating but also eliminates side reactions that would otherwise cause electrolyte depletion. As a result, Na-metal free full cells assembled with high capacity Na 3 V 2 (PO 4 ) 3 cathode delivered ~ 85% capacity retention for 100 cycles, higher than the 73% of retention of uncoated Al foil.

25 ENERGY STORAGE↗

Catalyst surfaces for the chromous/chromic redox couple

An electricity producing cell of the reduction-oxidation (REDOX) type is described. The cell is divided into two compartments by a membrane, each compartment containing a solid inert electrode. A ferrous/ferric couple in a chloride solution serves as a cathode fluid which is circulated through one of the compartments to produce a positive electric potential disposed therein. A chromic/chromous couple in a chloride solution serves as an anode fluid which is circulated through the second compartment to produce a negative potential on an electrode disposed therein. The electrode is an electrically conductive, inert material plated with copper, silver or gold. A thin layer of lead plates onto the copper, silver or gold layer when the cell is being charged, the lead ions being available from lead chloride which was added to the anode fluid. If the REDOX cell is then discharged, the current flows between the electrodes causing the lead to deplate from the negative electrode and the metal coating on the electrode will act as a catalyst to cause increased current density.

Giner, J. D.↗

Improving the Electrocatalytic Activity and Durability of the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ Cathode by Surface Modification

Electrode materials with high activity and good stability are essential for commercialization of energy conversion systems such as solid oxide fuel cells or electrolysis cells at the intermediate temperature. Modifying the existing perovskite-based electrode surface to form a heterostructure has been widely applied for the rational design of novel electrodes with high performance. Despite many successful developments in enhancing electrode performance by surface modification, some controversial results are also reported in the literature and the mechanisms are still not well understood. In this work, the mechanism of how surface modification impacts the oxygen reduction reaction (ORR) activity and stability of perovskite-based oxides was investigated. We took La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) as the thin-film model system and modified its surface with additive Pr x Ce 1–x O 2 layers of different thicknesses. We found a strong correlation between surface oxygen defects and the ORR activity of the heterostructure. By inducing higher oxygen vacancy concentration compared to bare LSCF, PrO 2 coating is proved to greatly facilitate the rate of oxygen dissociation, thus significantly enhancing the ORR activity. Because of low oxygen vacancy density introduced by Pr 0.2 Ce 0.8 O 2 and CeO 2 coating, on the one hand, it does not boost the rate of ORR but successfully suppresses surface Sr segregation, leading to an enhanced durability. Our findings will demonstrate the vital role of surface oxygen defects and provide important insights for the rational design of high-performance electrode materials through surface defect engineering.

25 ENERGY STORAGE↗

Modification of LiMn 2 O 4 surfaces by controlling the Acid–Base surface chemistry of atomic layer deposition

In this combined theoretical and experimental study, we report the effects of Al precursor selection on the growth chemistry, interfacial structure, and electrochemistry of Al 2 O 3 coatings on spinel LiMn 2 O 4 (LMO) surfaces by atomic layer deposition (ALD). Five Al precursors, exhibiting a range of Lewis acid-base properties, were used to establish trends in the ALD Al 2 O 3 growth chemistry on LMO powders in comparison to redox-inactive planar silicon substrates. We show that the Lewis acid-base properties of the Al precursor ligands can be used to tune both the Mn oxidation states and the Al 2 O 3 coverage on the LMO surface. Density functional theory calculations are used to examine the reaction mechanism of each precursor on LMO surfaces, elucidating a correlation between the Lewis acidity of the ligands and the decomposition thermochemistry. In-depth X-ray photoelectron spectroscopy and in situ Fourier transform infrared spectroscopy measurements support these theoretical predictions and further reveal how different Al precursors modify the atomic and electronic structure near the LMO surface during ALD. While the Mn oxidation state is strongly influenced by the Lewis acidity of the precursor ligand, the surface coverage and thickness of the Al 2 O 3 coating are a more representative descriptor of the electrochemical performance measured in coin cell experiments. Finally, we show how the ligand acid-base properties of ALD precursors can be used to rationally tailor atomic layer growth mechanisms, which may enable atomic level control over the structure of functionalized interfaces for various applications related to catalysis, semiconductors, and energy storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhancement of SOFC Cathode Electrochemical Performance Using Multi-Phase Interfaces

This work explored the use of oxide heterostructures for enhancing the catalytic and degradation properties of solid oxide fuel cell (SOFC) cathode electrodes. We focused on heterostructures of Ruddlesden-Popper and perovskite phases. Building on previous work showing enhancement of the Ruddlesden-Popper (La,Sr) 2 CoO 4 / perovskite (La,Sr)CoO 3 heterostructure compared to pure (La,Sr)CoO 3 we explored the application of related heterostructures of Ruddlesden-Popper phases on perovskite (La,Sr)(Co,Fe)O 3 . Our approaches included thin-film electrodes, physical and electrochemical characterization, elementary reaction kinetics modeling, and ab initio simulations. We demonstrated that Sr segregation to surfaces is likely playing a critical role in the performance of (La,Sr)CoO 3 and (La,Sr)(Co,Fe)O 3 and that modification of this Sr segregation may be the mechanism by which Ruddlesden-Popper coatings enhance performances. We determined that (La,Sr)(Co,Fe)O 3 could be enhanced in thin films by about 10× by forming a heterostructure simultaneously with (La,Sr) 2 CoO 4 and (La,Sr)CoO 3 . We hope that future work will develop this heterostructure for use as a bulk porous electrode.

25 ENERGY STORAGE↗