Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Laser-induced slip casting as an additive manufacturing approach for silicon carbide

Here, this work presents processing silicon carbide (SiC) with the laser-induced slip casting (LIS) additive manufacturing (AM). SiC was stabilized in water with polyethyleneimine (PEI) dispersant, and SiC slurries were made with rheology for LIS printing. High-density ceramic parts were printed, followed by single-step binder burnout and sintering. The printed parts achieved 93–95 % of theoretical density. X-ray computed tomography (XCT) revealed a small distribution of flaws exceeding 100 microns. The mechanical properties were measured in both parallel and perpendicular to the printing layers, and the orientation with layers perpendicular to the bending moment resulted in higher strength compared to the parallel direction. Porosity resulting from processing and large inclusions of boron carbide (B4C) were the root cause of failure in the measured samples. Despite these defects through this effort, this new approach demonstrates promise for green forming of SiC with densities greater than 95 % theoretical and tensile strengths above 250 MPa.

Additive Manufacturing↗

Design of Circular, Square, Single, and Multi-layer Induction Coils for Electromagnetic Priming Using Inductance Estimates

Special induction coils used for electro magnetic priming of ceramic foam filters in liquid metal filtration have been designed using a combination of analytical and finite element modeling. Relatively simple empirical equations published by Wheeler in 1928 and 1982 have been used during the design process. The equations were found to accurately predict the z-component of the magnetic flux densities of both single- and multi-layer coils as verified both experimentally and by using COMSOL{sup ®} 5.1 multiphysics simulations.

36 MATERIALS SCIENCE↗

Innovations in the Use of Nuclear Energy for Sustainable Manufacturing

Abstract Over the next 50 years, nuclear energy will become increasingly important in providing the electricity and heat needed both by the presently industrialized countries and by those countries which are now developing their manufacturing industries. The twin concerns of global climate change and of the vulnerability of energy supplies caused by increasing international competition will lead to a greater reliance on nuclear energy for both electricity and process heat. Conservative estimates of new nuclear construction indicate a 50% increase in capacity by 2030. Other estimates predict a tripling of present capacity. Required machine tool technologies will include the improvements in the manufacture of standard LWR components, such as pressure vessels and pumps. Further in the future, technologies for working high temperature metals and ceramics will be needed and will require new machining capabilities.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Miniature low-pass filter in low-loss 9k7 LTCC

DuPont 9k7 low-temperature cofired ceramic (LTCC) is a low-loss, or high-quality-factor Q, tape system targeting at radio frequency (RF) applications. This paper reports on the effect of a critical process parameter, the heating rate, on the densification and dielectric properties of the 9k7 LTCC. The role of competing densification and crystallization during the sintering of 9k7 is discussed. The high Q of DuPont 9K7 can be used to improve RF system performance, for example a better receiver noise figure, by designing embedded passive RF components such as inductors, capacitors and filters. Furthermore, miniaturized multilayer low-pass filters (LPF) with a wide stopband were fabricated to showcase the technology.

36 MATERIALS SCIENCE↗

Rolling Behavior of Surface Tagged Aluminum 6061 using Photoluminescent Oxides

Physical tagging of nuclear fuel is potentially one way of tracking throughout the fuel lifecycle. The process of tagging can take many forms, but one promising method is to embed a small amount of photoluminescent particles in the surface of a material which are not detectable under normal illumination but are readily visible under excitation by ultraviolet light. The goal of this project was to explore the potential to tag simulated nuclear fuel cladding with small ceramic particles, via laser beam welding or gas tungsten arc welding, and measure the photoluminescent response. Surface tagging using this method has demonstrated viability and detectability throughout this project; work in FY24 focused on the survivability of these tags through subsequent deformation processing similar to what taggants in a fuel manufacturing environment would be subjected to. This work demonstrated that particles are readily visible in the as-welded state (i.e., before subsequent rolling treatment to represent mechanical processing of a fuel material), but visibility is reduced as the deformation is induced. Despite the reduction in photoluminescence, the taggants are still visible after rolling processes are performed, making this surface tagging technique a promising candidate for nuclear fuel cladding tagging. This work demonstrated, though, that targeted optimization work would be necessary to develop a robust taggant depending on the fidelity and luminescent properties required.

36 MATERIALS SCIENCE↗

Phase Field Modeling of Pressure Induced Densification in Solid Electrolytes

Adoption of dense and homogeneous solid electrolytes can possibly mitigate the propagation of lithium dendrites and enable lithium metal anodes. Application of external pressure helps to minimize the sintering temperature in oxide ceramics and can potentially densify softer sulfide electrolytes even under room temperature conditions. Here, a previously developed phase field-based computational scheme for predicting the high-temperature sintering-induced densification of oxide ceramic solid electrolytes is extended in the present context to capture the influence of external pressure for densifying solid electrolytes. Two different bulk deformation mechanisms, namely, "reorganization" and "creep deformation," are dominant under external pressure, which is different from the surface and grain-boundary diffusion-induced densification of solid electrolytes that occurs during high temperature sintering. External pressure also increases the points of contact between the particles, which further enhances the propensity of diffusion-induced sintering process. Results obtained from simulations indicate that densification under external pressure is independent of the solid electrolyte particle morphology. Finally, a phase map is generated between applied pressure and temperature for achieving complete densification of oxide ceramics, which can possibly guide the synthesis of thin and dense solid electrolyte separators.

25 ENERGY STORAGE↗

Savannah River Site Defense Waste Processing Facility Melt Cell Remote Cleanup - 18037

This paper documents experiences at Savannah River Site (SRS) related to both the modification and use of a commercial remote vehicle to remove years of process-related litter (glass and various objects) from a hot cell floor during a production outage. The outage was necessary to replace a Department of Energy Environmental Management (DOE-EM) remotely-operated glass melter that had vitrified waste for 14 years at the Defense Waste Processing Facility. Both chunks of waste glass and numerous items littered the floor of the cell all associated with the long production run. The presence of litter become problematic as it could eventually impede movement or placement of items necessary to continue facility operation. The cleanup also reduces radiation rates within the hot cell which is beneficial. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optimized Slurries for Spray Drying: Different Approaches to Obtain Homogeneous and Deformable Alumina-Zirconia Granules

Spray drying is widely used for producing granulated feed materials for compaction process, which is the current industrial method for manufacturing alumina-zirconia femoral heads. The optimization of the granules compaction behavior requires the control of the slurry rheology. Moreover, for a dual-phase ceramic suspension, the even phase distribution has to be kept through the atomization step. Here we present two approaches addressing the key issues involved in the atomization of a composite system. Alumina-10 vol % zirconia powders were prepared by either a powder mixing route, or by the surface modification of a commercial α-alumina powder with a zirconium salt. Slurries from both powders were spray dried. The correlation between slurry rheology and pH, granules morphology and sintered microstructures was here investigated and discussed on the ground of the two feed materials characteristics. The processing conditions were optimized to obtain dense and homogeneous alumina-zirconia micro-nano composites by both processing routes.

36 MATERIALS SCIENCE↗

Spark Plasma Sintering of W-UO2 Cermets

About 50 vol.% 3 um depleted uranium dioxide (UO2) powder was encapsulated within a tungsten super alloy matrix produced from sub-micron tungsten powders using the Spark Plasma Sintering (SPS) process. An additive of 25 atom-percent (at.%) rhenium was included within the tungsten matrix to improve the ductility and fracture toughness of the ceramic–metallic (cermet) matrix. Cermet fabrication to 97.9% of the theoretical cermet density was achieved by sintering at 1500 degrees C with 40 MPa of applied pressure for 20 min. The results presented are from the first known trials of W–UO2 and nuclear cermet production via SPS.

36 MATERIALS SCIENCE↗

Pre-ceramic polymer-assisted nucleation and growth of copper sulfide nanoplates

Abstract Polymer-derived ceramics derived from pre-ceramic polymers (PCPs), have access to several form factors and are highly tunable systems. Tunability can be further expanded with the incorporation of functional nanoparticle fillers throughout the matrix for advanced nanocomposite polymer-derived ceramic development. However, capping ligands used in nanoparticle syntheses mix unfavorably with PCPs, giving aggregated filler material and diminished properties. To control dispersion, secondary nanoparticle processing is performed by adhering PCP-miscible caps to the surface after synthesis. This often sacrifices size control established for small nanoparticles (<10 nm). Herein, we successfully eliminate the need for extra nanoparticle processing through the development of a one-pot, copper sulfide synthesis in which a PCP assists the stable formation of nanoparticles and serves as the final graft molecule. We monitor the success of this methodology and the PCP’s role in the reaction through several characterization methods probing both the nanoparticle core and polymer graft.

Loughney, Patricia A. (ORCID:0000000199472267)↗

Ferroelectric and dielectric properties of ferrite-ferroelectric ceramic composites

Particulate composites of ferrite and ferroelectric phases with xNiFe{sub 2}O{sub 4} (NF) and (1 - x)Pb{sub 0.988}(Zr{sub 0.52}Ti{sub 0.48}){sub 0.976}Nb{sub 0.024}O{sub 3} (where x = 2, 10, 20, 30, 50, 70, and 100 wt. %) were prepared in situ by sol-gel method. The presence of a diphase composition was confirmed by X-ray diffraction while the microstructure of the composites was studied by scanning electron microscopy revealing a good mixing of the two phases and a good densification of the bulk ceramics. The dielectric permittivity shows usual dielectric dispersion behavior with increasing frequency due to Maxwell-Wagner interfacial polarization. AC conductivity measurements made in frequency range 1 Hz-1 MHz suggest that the conduction process is due to mixed polaron hopping. The effect of NF phase concentration on the P-E and M-H hysteresis behavior and dielectric properties of the composites was investigated. At low NF concentration a sharp ferro-paraelectric transition peak can be observed at around 360 Degree-Sign C while for higher NF concentrations a trend to a diffuse phase transition occurs. All the composite samples exhibit typical ferromagnetic hysteresis loops, indicating the presence of ordered magnetic structure.

36 MATERIALS SCIENCE↗

HIGH ALUMINUM HLW (HIGH LEVEL WASTE ) GLASSES FOR HANFORDS WTP (WASTE TREATMENT PROJECT)

This paper presents the results of glass formulation development and melter testing to identify high waste loading glasses to treat high-Al high level waste (HLW) at Hanford. Previous glass formulations developed for this HLW had high waste loadings but their processing rates were lower that desired. The present work was aimed at improving the glass processing rate while maintaining high waste loadings. Glass formulations were designed, prepared at crucible-scale and characterized to determine their properties relevant to processing and product quality. Glass formulations that met these requirements were screened for melt rates using small-scale tests. The small-scale melt rate screening included vertical gradient furnace (VGF) and direct feed consumption (DFC) melter tests. Based on the results of these tests, modified glass formulations were developed and selected for larger scale melter tests to determine their processing rate. Melter tests were conducted on the DuraMelter 100 (DMIOO) with a melt surface area of 0.11 m{sup 2} and the DuraMelter 1200 (DMI200) HLW Pilot Melter with a melt surface area of 1.2 m{sup 2}. The newly developed glass formulations had waste loadings as high as 50 wt%, with corresponding Al{sub 2}O{sub 3} concentration in the glass of 26.63 wt%. The new glass formulations showed glass production rates as high as 1900 kg/(m{sup 2}.day) under nominal melter operating conditions. The demonstrated glass production rates are much higher than the current requirement of 800 kg/(m{sup 2}.day) and anticipated future enhanced Hanford Tank Waste Treatment and Immobilization Plant (WTP) requirement of 1000 kg/(m{sup 2}.day).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Microstructure characterization of electric field assisted sintering (EFAS) sintered metallic and ceramic materials using local thermal diffusivity measurement

Electric Field Assisted Sintering (EFAS, also referred to as spark plasma sintering) is a powerful technology for the consolidation of powder materials. The high heating rate during the sintering process is critical for minimizing energy consumption, but it can also cause microstructure heterogeneities in sintered parts, such as spatially varied porosity. The examination of localized porosity usually requires the use of a scanning electron microscope with a carefully prepared surface. In this paper, photothermal radiometry is used to measure local thermal diffusivity and extract localized porosity of EFAS-sintered parts by using a percolation-threshold model. Applying this approach, we identified the radial position-dependent porosity variation in EFAS parts, which is likely formed due to the large temperature gradient during the sintering process. This approach has a unique advantage because it can measure samples with minimal or no surface preparation, enabling the possibility of in situ characterization in EFAS with proper system modification. Necessary modifications on the measurement approach for EFAS deployment and in situ characterization are also discussed.

36 MATERIALS SCIENCE↗

Radioactive Waste Conditioning, Immobilisation, And Encapsulation Processes And Technologies: Overview And Advances (Chapter 7)

The main immobilization technologies that are available commercially and have been demonstrated to be viable are cementation, bituminization, and vitrification. Vitrification is currently the most widely used technology for the treatment of high level radioactive wastes (HLW) throughout the world. Most of the nations that have generated HLW are immobilizing in either alkali borosilicate glass or alkali aluminophosphate glass. The exact compositions of nuclear waste glasses are tailored for easy preparation and melting, avoidance of glass-in-glass phase separation, avoidance of uncontrolled crystallization, and acceptable chemical durability, e.g., leach resistance. Glass has also been used to stabilize a variety of low level wastes (LLW) and mixed (radioactive and hazardous) low level wastes (MLLW) from other sources such as fuel rod cladding/decladding processes, chemical separations, radioactive sources, radioactive mill tailings, contaminated soils, medical research applications, and other commercial processes. The sources of radioactive waste generation are captured in other chapters in this book regarding the individual practices in various countries (legacy wastes, currently generated wastes, and future waste generation). Future waste generation is primarily driven by interest in sources of clean energy and this has led to an increased interest in advanced nuclear power production. The development of advanced wasteforms is a necessary component of the new nuclear power plant (NPP) flowsheets. Therefore, advanced nuclear wasteforms are being designed for robust disposal strategies. A brief summary is given of existing and advanced wasteforms: glass, glass-ceramics, glass composite materials (GCM’s), and crystalline ceramic (mineral) wasteforms that chemically incorporate radionuclides and hazardous species atomically in their structure. Cementitious, geopolymer, bitumen, and other encapsulant wasteforms and composites that atomically bond and encapsulate wastes are also discussed. The various processing technologies are cross-referenced to the various types of wasteforms since often a particular type of wasteform can be made by a variety of different processing technologies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Substitution behavior of x(Na{sub 0.5}K{sub 0.5})NbO{sub 3}-(1 − x)BaTiO{sub 3} ceramics for multilayer ceramic capacitors by a near edge x-ray absorption fine structure analysis

The doping effect of (Na{sub 0.5}K{sub 0.5})NbO{sub 3} (NKN) as alternatives for rare-earth elements on the electrical properties of BaTiO{sub 3} has been investigated, in terms of their substitution behavior. The dielectric constant of a specimen with x = 0.05 was about 79% higher than that of pure BaTiO{sub 3}, and the temperature coefficient of capacitance was satisfied by the X7R specification. The specimen with x = 0.05 showed the lowest tetragonality among the four compositions and had a fine grain size of <2 μm. Although the addition of NKN decreased the specimen's tetragonality, the electrical properties were enhanced by the formation of defect dipoles and conduction electrons, which resulted from an acceptor and donor substitution behavior. Through O K-edge near edge x-ray absorption fine structure spectroscopy, the practical substitution behavior was defined by the change in Ti 3d orbital states. The energy separation of the Ti 3d orbitals was more apparent with the specimen of x = 0.05, which is related to the donor level from the donor substitution of Nb{sup 5+} ion for Ti-sites. Therefore, the simultaneous substitution of Na{sup +}/K{sup +} and Nb{sup 5+} ions into BaTiO{sub 3} can improve dielectric properties, based on the charge-transfer process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Sol–gel preparation of well-adhered films and long range ordered inverse opal films of BaTiO{sub 3} and Bi{sub 2}Ti{sub 2}O{sub 7}

Highlights: • Highly adaptable sols are presented for processing of the electroceramic materials BaTiO{sub 3} and Bi{sub 2}Ti{sub 2}O{sub 7}. • High quality thin films are produced by dip coating with good phase control. • Infiltration of cross-linked polystyrene templates led to high quality inverse opals. - Abstract: Barium and bismuth titanate thin films and well-ordered inverse opal films are produced by dip coating from sols containing titanium alkoxides with acetic acid, acetylacetone, methoxyethanol and water. The inverse opal preparations used crosslinked polystyrene opal templates. Heat treatment in air produced tetragonal BaTiO{sub 3} or mixtures of the hexagonal and tetragonal phases, or phase pure Bi{sub 2}Ti{sub 2}O{sub 7}. Good quality films were obtained with a thickness of 5 μm from a single dipping, and the thickness could be increased by dipping multiple times. Inverse opals were well ordered and exhibited opalescence and photonic stop band effects.

36 MATERIALS SCIENCE↗

Equibiaxial flexural strength determination of UO 2 using a ball-on-ring test

To increase nuclear fuel performance and reliability, their mechanical properties require an accurate and statistically relevant assessment. Biaxial flexural strength tests provide an alternative to bend bar techniques for assessing mechanical behavior; namely, the transverse rupture strength (TRS) of ceramic samples. Biaxial test samples require simple geometries and minimal surface preparation, reducing fabrication costs and handling hazards. This study investigated the TRS of polycrystalline UO 2 fuel forms at room temperature using a ball-on-ring test fixture. Here, pellets were fabricated from UO 2 powder using conventional powder processing and sintering techniques. The TRS and Weibull parameters were obtained through Weibull statistics on over 60 UO 2 samples tested under equibiaxial flexure. The larger sample size in this study enabled a more robust Weibull statistical analysis than alternative test methods, which may not capture the stochastic failure of typical ceramics. Furthermore, two different loading ball diameters were employed to assess the impact of contact damage on fracture strength. While Hertzian contact damage was observed with the smaller loading ball, the fracture strength remained unaffected. A fracture analysis of the tested UO 2 samples indicated a mixture of intergranular and transgranular fracture that transitions to transgranular fracture with increasing distance from the fracture origin. The characteristic strength of the combined data sets was determined to be 148 MPa, and the Weibull modulus was determined to be 9.1. The TRS values and Weibull parameters were close to values found in the literature for alternative testing techniques using samples with similar microstructure and density. The findings in this study validate the ball-on-ring method used to obtain the TRS of UO 2 with a sample geometry more representative of nuclear fuels. Additionally, experimental TRS results from this study can be implemented in modeling codes to predict fuel performance, which is critical to fuel burnup extension and advanced nuclear fuel technologies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗