Search NASA⌕ Search

SEARCH · Search NASA

Results for “cleaning methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Evaluating Ru-RuO 2 @BN as a Bifunctional Electrocatalyst for the Nitrogen Reduction Reaction and the Hydrogen Evolution Reaction

Electrochemical approaches toward clean energy production have been the focus of significant attention. Here, the nitrogen (N 2 ) reduction reaction (NRR) and the hydrogen (H 2 ) evolution reaction (HER) offer a promising method for producing NH 3 and H 2 , respectively. Nevertheless, practical obstacles that must be overcome in creating optimal catalysts are the sluggish kinetics and low selectivity of NRR and HER. Herein, we report on the synthesis of a Ru-RuO 2 -decorated boron nitride (BN) catalyst that shows excellent activity toward NRR. A rate of NH3 formation (V NH3 ) of 16.8 μg h -1 mg -1 and a corresponding Faradaic efficiency (FE) of 52.9% were noted at a potential of −0.5 V in 0.1 M HCl. However, the HER activity of Ru-RuO 2 @BN was found to be highly suppressed in 0.1 M HCl and did not yield a reasonable overpotential value. Thus, the capability of this material toward NRR suggests its viability as a promising catalyst for clean NH 3 production.

30 DIRECT ENERGY CONVERSION↗

Silane Modification of Glass and Silica Surfaces to Obtain Equally Oil-Wet Surfaces in Glass-Covered Silicon Micromodel Applications

The wettability of silicon and glass surfaces can be modified by silanization. However, similar treatments of glass and silica surfaces using the same silane do not necessarily yield the same wettability as determined by the oil-water contact angle. In this technical note, surface cleaning pretreatments were investigated to determine conditions that would yield oil-wet surfaces on glass with similar wettability to silica surfaces treated with the same silane, and both air-water and oil-water contact angles were determined. Air-water contact angles were less sensitive to differences between silanized silica and glass surfaces, often yielding similar values while the oil-water contact angles were quite different. Borosilicate glass surfaces cleaned with standard cleaning solution 1 (SC1) yield intermediate-wet surfaces when silanized with hexamethyldisilazane, while the same cleaning and silanization yields oil-wet surfaces on silica. However, cleaning glass in boiling concentrated nitric acid creates a surface that can be silanized to obtain oil-wet surfaces using HDMS. Moreover, this method is effective on glass with prior thermal treatment at an elevated temperature of 400oC. In this way, silica and glass can be silanized to obtain equally oil-wet surfaces using HMDS. It is demonstrated that pretreatment and silanization is feasible in silicon-silica/glass micromodels previously assembled by anodic bonding, and that the change in wettability has a significant observable effect on immiscisble fluid displacements in the pore network.

contact angle↗

Self-assembly of Ge quantum dots on periodically corrugated Si surfaces

The fabrication of regularly ordered Ge quantum dot arrays on Si surfaces usually requires extensive preparation processing, ensuring clean and atomically ordered substrates, while the ordering parameters are quite limited by the surface properties of the substrate. Here, we demonstrate a simple method for fabrication of ordered Ge quantum dots with highly tunable ordering parameters on rippled Si surfaces. The ordering is achieved by magnetron sputter deposition, followed by an annealing in high vacuum. We show that the type of ordering and lattice vector parameters of the formed Ge quantum dot lattice are determined by the crystallographic properties of the ripples, i.e., by their shape and orientation. Moreover, the ordering is achieved regardless the initial amorphisation of the ripples surface and the presence of a thin oxide layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An attempt to simulate laser-induced all-optical spin switching in a crystalline ferrimagnet

Interest in all-optical spin switching (AOS) is growing rapidly. The recent discovery of AOS in Mn 2 RuGa provides a much needed clean case of crystalline ferrimagnets for theoretical simulations. Here, we attempt to simulate it using the state-of-the-art first-principles method combined with the Heisenberg exchange model. We first compute the spin moments at two inequivalent manganese sites and then feed them into our model Hamiltonian. We employ an ultrafast laser pulse to switch the spins. We find that there is a similar optimal laser field amplitude to switch spins. However, we find that the exchange interaction has a significant effect on the system switchability. Weakening the exchange interaction could make the system unswitchable. This provides a crucial insight into the switching mechanism in ferrimagnets.

36 MATERIALS SCIENCE↗

Using HT and DT gamma rays to diagnose mix in Omega capsule implosions

Experimental evidence [1] indicates that shell material can be driven into the core of Omega capsule implosions on the same time scale as the initial convergent shock. It has been hypothesized that shock-generated temperatures at the fuel/shell interface in thin exploding pusher capsules diffusively drives shell material into the gas core between the time of shock passage and bang time. Here, we propose a method to temporally resolve and observe the evolution of shell material into the capsule core as a function of fuel/shell interface temperature (which can be varied by varying the capsule shell thickness). Our proposed method uses a CD plastic capsule filled with 50/50 HT gas and diagnosed using gas Cherenkov detection (GCD) to temporally resolve both the HT "clean" and DT "mix" gamma ray burn histories. Simulations using Hydra [2] for an Omega CD-lined capsule with a sub-micron layer of the inside surface of the shell pre-mixed into a fraction of the gas region produce gamma reaction history profiles that are sensitive to the depth to which this material is mixed. Furthermore, we observe these differences as a function of capsule shell thickness is proposed to determine if interface mixing is consistent with thermal diffusion λ ii ~T 2 /Z 2 ρ at the gas/shell interface. Finally, since hydrodynamic mixing from shell perturbations, such as the mounting stalk and glue, could complicate these types of capsule-averaged temporal measurements, simulations including their effects also have been performed showing minimal perturbation of the hot spot geometry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Binary neutron-star mergers with Whisky and SACRA: First quantitative comparison of results from independent general-relativistic hydrodynamics codes

We present the first quantitative comparison of two independent general-relativistic hydrodynamics codes, the whisky code and the sacra code. We compare the output of simulations starting from the same initial data and carried out with the configuration (numerical methods, grid setup, resolution, gauges) which for each code has been found to give consistent and sufficiently accurate results, in particular, in terms of cleanness of gravitational waveforms. We focus on the quantities that should be conserved during the evolution (rest mass, total mass energy, and total angular momentum) and on the gravitational-wave amplitude and frequency. We find that the results produced by the two codes agree at a reasonable level, with variations in the different quantities but always at better than about 10%.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Protection of extreme ultraviolet lithography masks. II. Showerhead flow mitigation of nanoscale particulate contamination [Protection of EUV lithography masks II: Showerhead flow mitigation of nanoscale particulate contamination]

An analysis is presented of a method to protect the reticle (mask) in an extreme ultraviolet (EUV) mask inspection tool using a showerhead plenum to provide a continuous flow of clean gas over the surface of a reticle. The reticle is suspended in an inverted fashion (face down) within a stage/holder that moves back and forth over the showerhead plenum as the reticle is inspected. It is essential that no particles of 10-nm diameter or larger be deposited on the reticle during inspection. Particles can originate from multiple sources in the system, and mask protection from each source is explicitly analyzed. The showerhead plate has an internal plenum with a solid conical wall isolating the aperture. The upper and lower surfaces of the plate are thin flat sheets of porous-metal material. These porous sheets form the top and bottom showerheads that supply the region between the showerhead plate and the reticle and the region between the conical aperture and the Optics Zone box with continuous flows of clean gas. The model studies show that the top showerhead provides robust reticle protection from particles of 10-nm diameter or larger originating from the Reticle Zone and from plenum surfaces contaminated by exposure to the Reticle Zone. Protection is achieved with negligible effect on EUV transmission. Furthermore, the bottom showerhead efficiently protects the reticle from nanoscale particles originating from the Optics Zone.

36 MATERIALS SCIENCE↗

Rare earth elements from waste

Rare earth elements (REEs) are critical materials in electronics and clean technologies. With the diminishing of easily accessible minerals for mining, the REE recovery from waste is an alternative toward a circular economy. Present methods for REE recovery suffer from lengthy purifications, low extractability, and high wastewater streams. Here, we report an ultrafast electrothermal process (~3000°C, ~1 s) based on flash Joule heating (FJH) for activating wastes to improve REE extractability. FJH thermally degrades or reduces the hard-to-dissolve REE species to components with high thermodynamic solubility, leading to ~2× increase in leachability and high recovery yields using diluted acid (e.g., 0.1 M HCl). The activation strategy is feasible for various wastes including coal fly ash, bauxite residue, and electronic waste. The rapid FJH process is energy-efficient with a low electrical energy consumption of 600 kWh ton –1 . The potential for this route to be rapidly scaled is outlined.

01 COAL, LIGNITE, AND PEAT↗

Impact of axial velocity and transmembrane pressure (TMP) on ARP filter performance

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. One potential method for increasing filter flux is to adjust the axial velocity and transmembrane pressure (TMP). SRR requested SRNL to conduct bench-scale filter tests to evaluate the effects of axial velocity and transmembrane pressure on crossflow filter flux. The objective of the testing was to determine whether increasing the axial velocity at the ARP could produce a significant increase in filter flux. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate and 2.5 g MST/L, processing the slurry through a bench-scale crossflow filter unit at varying axial velocity and TMP, and measuring filter flux as a function of time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Thermophysical Properties of TcO2

Technetium-99 is a highly radioactive isotope with a long half-life that is common in nuclear waste. It volatizes at a low temperature, which poses a significant challenge to the clean-up and containment processes. Due to difficulties in purifying technetium compounds, their thermophysical properties have not been measured or calculated. Here, first principle methods are used along with the quasi quasi-harmonic harmonic approximation to compute the Debye temperature, volumetric thermal expansion coefficient, bulk modulus, and heat capacity of rutile TcO2 for temperatures ranging from 0 to 1500 K and applied pressures ranging from 0 to 255 GPa. The computed atomic structures agree well with the results from diffraction measurements. The computed thermophysical properties are in the neighborhood of other rutile metal oxides and, in particular, are within approximately 10–13% of rutile ReO2, which is frequently used as a substitute for TcO2 in experimental studies.

Zhong, Hong↗

Practical method for diffusion welding of steel plate in air.

Description of a simple and easily applied method of diffusion welding steel plate in air which does not require a vacuum furnace or hot press. The novel feature of the proposed welding method is that diffusion welds are made in air with deadweight loading. In addition, the use of an autogenous (self-generated) surface-cleaning principle (termed 'auto-vac cleaning') to reduce the effects of surface oxides that normally hinder diffusion welding is examined. A series of nine butt joints were diffusion welded in thick sections of AISI 1020 steel plate. Diffusion welds were attempted at three welding temperatures (1200, 1090, and 980 C) using a deadweight pressure of 34,500 N/sq m (5 psi) and a two-hour hold time at temperature. Auto-vac cleaning operations prior to welding were also studied for the same three temperatures. Results indicate that sound welds were produced at the two higher temperatures when the joints were previously fusion seal welded completely around the periphery. Also, auto-vac cleaning at 1200 C for 2-1/2 hours prior to diffusion welding was highly beneficial, particularly when subsequent welding was accomplished at 1090 C.

Moore, T. J.↗

Fluorescent penetrant inspection

The purpose of this experiment is to familiarize the student with fluorescent penetrant inspection and to relate it to classification of various defects. The penetrant method of nondestructive testing is a method for finding discontinuities open to the surface in solids and essentially nonporous bodies. The method employs a penetrating liquid which is applied over the surface and enters the discontinuity or crack. After the excess of penetrant has been cleaned from the surface, the penetrant which exudes or is drawn back out of the crack indicates the presence and location of a discontinuity. The experimental procedure is described.

Sastri, Sankar↗

Nonlinear aerodynamics and the design of wing tips

This contract began in April 1990 with studies on the effect of wingtip shape on induced drag. That work considered problems of determining induced drag from computational aerodynamic methods and examined effects of wake roll up on the induced drag of elliptical and crescent wings. The research contract was continued in April 1991 and again in April 1992 with scope augmented to include considerations other than induced drag. The idea was to develop methods for comparing wing tip shapes on the basis of their effects on total drag, structural weight, and high lift performance. To accomplish this, work was done to improve methods for multidisciplinary analysis and optimization of wings. This report describes results of research conducted from April 1992 through March 1993. The general objective was to improve an existing wing optimization method and apply the method to specific problems of interest. The method, while a valuable tool for wing tip design studies, can be applied to more general problems, and has been applied to some of these other problems during its development. Specific goals that were accomplished are listed below and are explained in more detail in attached reports: analysis methods were improved in the area of structural modeling; small improvements to the high lift model were made, and ideas were collected on how clean wing c(sub l(sub max)) should vary with sweep - these ideas should provide a guide for future examination of high lift with experiment or CFD; and a calculation for drag due to the loss of leading edge suction was added to the wing analysis.

Kroo, Ilan↗

Planetary Protection Bioburden Analysis Program

This program is a Microsoft Access program that performed statistical analysis of the colony counts from assays performed on the Mars Science Laboratory (MSL) spacecraft to determine the bioburden density, 3-sigma biodensity, and the total bioburdens required for the MSL prelaunch reports. It also contains numerous tools that report the data in various ways to simplify the reports required. The program performs all the calculations directly in the MS Access program. Prior to this development, the data was exported to large Excel files that had to be cut and pasted to provide the desired results. The program contains a main menu and a number of submenus. Analyses can be performed by using either all the assays, or only the accountable assays that will be used in the final analysis. There are three options on the first menu: either calculate using (1) the old MER (Mars Exploration Rover) statistics, (2) the MSL statistics for all the assays, or This software implements penetration limit equations for common micrometeoroid and orbital debris (MMOD) shield configurations, windows, and thermal protection systems. Allowable MMOD risk is formulated in terms of the probability of penetration (PNP) of the spacecraft pressure hull. For calculating the risk, spacecraft geometry models, mission profiles, debris environment models, and penetration limit equations for installed shielding configurations are required. Risk assessment software such as NASA's BUMPERII is used to calculate mission PNP; however, they are unsuitable for use in shield design and preliminary analysis studies. The software defines a single equation for the design and performance evaluation of common MMOD shielding configurations, windows, and thermal protection systems, along with a description of their validity range and guidelines for their application. Recommendations are based on preliminary reviews of fundamental assumptions, and accuracy in predicting experimental impact test results. The software is programmed in Visual Basic for Applications for installation as a simple add-in for Microsoft Excel. The user is directed to a graphical user interface (GUI) that requires user inputs and provides solutions directly in Microsoft Excel workbooks. This work was done by Shannon Ryan of the USRA Lunar and Planetary Institute for Johnson Space Center. Further information is contained in a TSP (see page 1). MSC- 24582-1 Micrometeoroid and Orbital Debris (MMOD) Shield Ballistic Limit Analysis Program Lyndon B. Johnson Space Center, Houston, Texas Commercially, because it is so generic, Enigma can be used for almost any project that requires engineering visualization, model building, or animation. Models in Enigma can be exported to many other formats for use in other applications as well. Educationally, Enigma is being used to allow university students to visualize robotic algorithms in a simulation mode before using them with actual hardware. This work was done by David Shores and Sharon P. Goza of Johnson Space Center; Cheyenne McKeegan, Rick Easley, Janet Way, and Shonn Everett of MEI Technologies; Mark Manning of PTI; and Mark Guerra, Ray Kraesig, and William Leu of Tietronix Software, Inc. For further information, contact the JSC Innovation Partnerships Office at (281) 483-3809. MSC-24211-1 Spitzer Telemetry Processing System NASA's Jet Propulsion Laboratory, Pasadena, California The Spitzer Telemetry Processing System (SirtfTlmProc) was designed to address objectives of JPL's Multi-mission Image Processing Lab (MIPL) in processing spacecraft telemetry and distributing the resulting data to the science community. To minimize costs and maximize operability, the software design focused on automated error recovery, performance, and information management. The system processes telemetry from the Spitzer spacecraft and delivers Level 0 products to the Spitzer Science Center. SirtfTlmProc is a unique system with automated error notification and recovery, with a real-time continuous service that can go quiescent after periods of inactivity. The software can process 2 GB of telemetry and deliver Level 0 science products to the end user in four hours. It provides analysis tools so the operator can manage the system and troubleshoot problems. It automates telemetry processing in order to reduce staffing costs. This work was done by Alice Stanboli, Elmain M. Martinez, and James M. McAuley of Caltech for NASA's Jet Propulsion Laboratory. For more information, contact iaoffice @jpl.nasa.gov. This software is available for commercial licensing. Please contact Dan Broderick at Daniel.F. Broderick@jpl.nasa.gov. Refer to NPO-47803. NASA Tech Briefs, September 2013 29 This rapid response computer program predicts Orbiter Wing Leading Edge (WLE) damage caused by ice or foam impact during a Space Shuttle launch (Program "IMPACT2"). The program was developed after the Columbia accident in order to assess quickly WLE damage due to ice, foam, or metal impact (if any) during a Shuttle launch. IMPACT2 simulates an impact event in a few minutes for foam impactors, and in seconds for ice and metal impactors. The damage criterion is derived from results obtained from one sophisticated commercial program, which requires hours to carry out simulations of the same impact events. The program was designed to run much faster than the commercial program with prediction of projectile threshold velocities within 10 to 15% of commercial-program values. The mathematical model involves coupling of Orbiter wing normal modes of vibration to nonlinear or linear springmass models. IMPACT2 solves nonlinear or linear impact problems using classical normal modes of vibration of a target, and nonlinear/ linear time-domain equations for the projectile. Impact loads and stresses developed in the target are computed as functions of time. This model is novel because of its speed of execution. A typical model of foam, or other projectile characterized by material nonlinearities, impacting an RCC panel is executed in minutes instead of hours needed by the commercial programs. Target damage due to impact can be assessed quickly, provided that target vibration modes and allowable stress are known. This work was done by Robert Clark, Jr., Paul Cotter, and Constantine Michalopoulos of The Boeing Company for Johnson Space Center. For further information, contact the JSC Innovation Partnerships Office at (281) 483-3809. MSC-24988-1 Wing Leading Edge RCC Rapid Response Damage Prediction Tool (IMPACT2) Lyndon B. Johnson Space Center, Houston, Texas (3) the MSL statistics for only the accountable assays. Other options on the main menu include a data editing form and utility programs that produce various reports requested by the microbiologists and the project, and tools to generate the groupings for the final analyses. The analyses can be carried out in three ways: Each assay can be treated separately, the assays can be collectively treated for the whole zone as a group, or the assays can be collected in groups designated by the JPL Planetary Protection Manager. The latter approach was used to generate the final report because assays on the same equipment or similar equipment can be assumed to have been exposed to the same environment and cleaning. Thus, the statistics are improved by having a larger population, thereby reducing the standard deviation by the square root of N. For each method mentioned above, three reports are available. The first is a detailed report including all the data. This version was very useful in verifying the calculations. The second is a brief report that is similar to the full detailed report, but does not print out the data. The third is a grand total and summary report in which each assay requires only one line. For the first and second reports, most of the calculations are performed in the report section itself. For the third, all the calculations are performed directly in the query bound to the report. All the numerical results were verified by comparing them with Excel templates, then exporting the data from the Planetary Protection Analysis program to Excel.

Beaudet, Robert A.↗

Microbial Bioburden on NASA Cleanroom Surfaces: Cell Counting and Fluorescence in situ Hybridization

Spacecraft assembly cleanrooms can harbor a low number of microbial cells that could contaminate hardware designed for life detection missions (known as “bioburden”). We are evaluating epifluorescence microscopy and fluorescence in situ hybridization (FISH) as rapid, accurate, and cost-effective methods to complement other contamination detection techniques. This study is part of a larger effort to characterize background organic contamination and the efficacy of cleaning procedures in Johnson Space Center (JSC) Astromaterials Curation Laboratories and Goddard Space Flight Center (GSFC) spacecraft assembly rooms. The low level of biomass required careful use of blanks during each stage of sample collection and preparation. FISH was performed using general archaeal and bacterial probes, as well as some group-specific probes. While some active bacteria were identified, a large majority of them were dead or inactive, and thus were difficult to identify by standard FISH. Our results are consistent with other studies that show that the bioburden present in clean rooms includes active, dormant, and dead cells.

C J Huff↗

Method of purifying a gas stream using 1,2,3-triazolium ionic liquids

A method for separating a target gas from a gaseous mixture using 1,2,3-triazolium ionic liquids is presented. Industrial effluent streams may be cleaned by removing carbon dioxide from the stream by contacting the effluent stream with a 1,2,3-triazolium ionic liquid compound.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integrating Energy Efficiency Strategies with Industrialized Construction for Our Clean Energy Future: Preprint

NREL’s Industrialized Construction Innovation Team has developed an ambitious plan to accelerate the integration of energy efficiency (EE) strategies with Industrialized Construction (IC). The United States (U.S.) construction industry is beginning to use IC methods to build multifamily apartment buildings to address affordability and labor shortages. Apart from reducing cost of construction and delivery times, the IC method of permanent modular construction has the potential to facilitate the integration of a wide range of EE strategies and advanced controls into such buildings. While there may be unintended EE benefits to IC such as a tighter envelope due to higher construction quality, the process has not been leveraged specifically to enhance EE. NREL aims to claim this missed opportunity and integrate IC benefits with EE as well as advanced controls, distributed energy resources, and grid-friendly design strategies. The paper proposes an ‘IC Assessment Framework’ to achieve affordable zero-energy modular multifamily buildings. Through the selection criteria of Design for Manufacturing and Assembly, the framework aims to distill a broad range of proven EE strategies for site-built into a set of strategies that qualify as easy to integrate for off-site. The output is a Factory Information Model (FIM) that represents a process-based digital twin to enable advanced time-and-motion study, plugs into open source building energy modeling platform (EnergyPlus), and serves as a vital tool facilitating wider adoption of EE integration. Conclusively, the paper delineates next steps for upcoming pilots with NREL’s IC partners towards developing a transformational pathway for our Clean Energy Future.

30 DIRECT ENERGY CONVERSION↗

Significance and complications of drilling fluid rheology in geothermal drilling: A review

The harsh downhole conditions of high pressure and high temperature (HPHT) encountered in geothermal wells make the drilling operation challenging. Drilling in such environments requires a special drilling mud formulation with high thermal stability and good rheological properties to fulfill the drilling fluid functions. Therefore, great efforts should be put into selecting the suitable drilling fluid, optimize and monitor the drilling fluid properties throughout drilling operations, and predicting its performance under downhole conditions. Rheological properties significantly impact many drilling parameters such as hole cleaning, fluid and wellbore stability, wellbore hydraulics, torque and drag, and other drilling issues. This paper discusses water-based drilling fluids' flow behavior under HPHT conditions and highlights the significance of fluid rheology in geothermal drilling. The common challenges and complications related to fluid rheology encountered in geothermal drilling are addressed in this paper, such as hole cleaning, wellbore hydraulics, and drilling fluid stability. This article also reviews the recent advances in drilling mud systems, rheology enhancement, and rheological properties measurements at surface and subsurface conditions. Furthermore, the rheology models of drilling fluid at elevated temperatures are reviewed to fully understand their flow behavior and establish a method for drilling engineers to optimize fluid formulations for geothermal drilling.

58 GEOSCIENCES↗