Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Hybrid Ag 2 VO 2 PO 4 /CF x as a High Capacity and Energy Cathode for Primary Batteries

In this report, we describe the electrochemistry of hybrid dual silver vanadium phosphorus oxide/carbon fluoride (Ag 2 VO 2 PO 4 /CF x ) cathodes with various weight ratios. Through modification of the Ag 2 VO 2 PO 4 /CF x ratio, we can control the gravimetric and volumetric capacity, as well as mitigate the voltage drop during high current pulses. The increase in impedance caused by irreversible LiF formation in CFx was reduced by the silver reduction-displacement during electrochemical discharge of the Ag 2 VO 2 PO 4 . Moreover, the addition of graphite was shown to reduce initial voltage delay. When Ag 2 VO 2 PO 4 dominates the electrode mass (i.e. 75/25 Ag 2 VO 2 PO 4 /CF x ) in the hybrid cathode, pulse testing shows less voltage drop and delay, but at the expense of capacity and energy density. As the amount of CFx in the composite increases (i.e. Ag 2 VO 2 PO 4 /CF x ratio of to 50/50 or 25/75), charge capacity and energy density increases, but at the expense of larger voltage drops and delays early in the discharge process. Thus, controlling the Ag 2 VO 2 PO 4 /CF x ratio can be used to tune the electrochemical properties of the dual cathode, allowing for optimization of capacity and power depending on the application.

25 ENERGY STORAGE↗

Infrared Microscopy as a Probe of Composition within a Model Biofuel Cell Electrode Prepared from Trametes versicolor Laccase

Abstract Infrared microscopy was applied in the study of laccase biofuel cell electrodes that demonstrated high current and power densities traceable to the use of a low equivalent weight (EW), short side chain (Aquivion) ionomer in the catalyst layer. The electrodes were prepared from a biocatalyst ink composed of orientation‐directing anthracene‐modified multi‐walled carbon nanotubes (An‐MWCNTs) in a dispersion of ionomer exchanged by hydrophobic cations. The ink was applied to an electronically conductive carbon felt support that was hot‐pressed to a Nafion‐NRE 212 (51 μm thickness) membrane, forming the framework for an air‐breathing biofuel cell cathode. Infrared microscopy sampling was performed with the use of a micro‐attenuated total reflection probe that enabled spectra to be recorded from ∼32 μm diameter circular spatial regions on the materials investigated. Sensitivity to deformation of the soft polymer membrane‐based materials was assessed through trial experiments on pure membrane samples before approaching the compositionally more complex biofuel cell electrodes. In studies of laccase cathodes, infrared spectral features of enzyme, buffer anions and surrounding An‐MWCNTs were identified. Heterogeneity in the spatial distribution of components and unexpected bands traceable to insoluble copper salts were detected. The results suggest directions for improving electrode activity and bring to light needs for advancing quantitative interpretations.

Liang, Ying↗

The [M 6 (S 2 C 2 Ph 2 ) 6 ] (M = Ni, Pd, Pt) Series: Multielectron Reservoirs That Sustain Ligand-Based Oxidations and Metal-Based Reductions

A complete [M 6 (S 2 C 2 R 2 ) 6 ] series (M = Ni (1), Pd (2), Pt (3); R = Ph), the rarest variety among homoleptic dithiolene transition-metal compounds, has been prepared by reaction between [M(S 2 C 2 Ph 2 ) 2 ] and a M 0 source. The platinum member of this set is the first of its type. Diffraction-quality crystals, grown with high reproducibility by evaporation from PhNO 2 solutions, reveal fully reduced [Ph 2 C 2 S 2 ] 2– dianions and an octahedral M 6 core that is reduced to C 2 symmetry by the fusion of a mononuclear D 2h [M(S 2 C 2 Ph 2 ) 2 ] fragment upon a C 4 -symmetric base. The [Ni 6 (S 2 C 2 Ph 2 ) 2 ] 1– monoanion, prepared by Cp* 2 Co reduction, shows only modest structural differences from its neutral counterpart. In CH 2 Cl 2 , 1 and 2 can undergo two reductions and an oxidation, while 3 sustains two reductions and two oxidations. In benzonitrile, 1 sustains three reversible oxidations at potentials that are shifted appreciably to less positive values. The cathodic processes are shown by density functional theory (DFT) calculations to involve an MO largely of metal–sulfur composition that has contributions throughout the C 4 -symmetric pentametallic base of the assembly, while the oxidations are largely ligand-based and confined to the monometallic [M(S 2 C 2 Ph 2 ) 2 ] cap. The absorption spectra are marked by multiple overlapping bands that produce a continuous, tapering absorption profile of unresolved shoulders and swells.

Ligands↗

In situ determination of lithium ion cathode/electrolyte thickness and composition as a function of charge

In this work we report the first experimental in situ determination of the thickness and estimated composition of a condensed electrode/electrolyte interface at various states of charge for the high voltage Li-ion cathode LiMn1.5Ni0.5O4 by exploiting the power of neutron reflectometry.1 Understanding the electrode/electrolyte interface is critical to developing an understanding of interfacial reactions needed to model transport phenomena and predict more stable electrolytes for electrochemical cells.2,3 However, developing the ability to control interfacial reactions in electrochemical cells is arguably one of the most critical challenges confronting researchers focused on energy storage and conversion reactions as well as liquid phase reactions such as photocatalysts and biomass conversion.2 For example, in electrochemical energy storage systems, such as batteries, the reactions between a solid electrode and a liquid electrolyte can lead to the formation of the solid electrolyte interphase (SEI), which directly mediates the stability, durability and safety of the cell. Controlling these interfacial reactions is essential to developing new, durable, and higher energy storage systems needed in the future.

Neutron Reflectometry↗

Hidden Subsurface Reconstruction and Its Atomic Origins in Layered Oxide Cathodes

Structural transformations near surfaces of solid-state materials underpin functional mechanisms of a broad range of applications including catalysis, memory, and energy storage. It has been a long-standing notion that the outmost free surfaces, accompanied by broken translational symmetry and altered atomic configurations, are usually the birthplace for structural transformations. Here, in a layered oxide cathode for Li-ion batteries, we for the first time observe the incipient state of the well documented layered-to-spinel-like structural transformation, which is surprisingly initiated from subsurface layer, rather than the very surface. Coupling atomic level scanning transmission electron microscopy imaging with electron energy loss spectroscopy, we discover that the reconstructed subsurfaces, featuring a mix of discrete patches of layered and spinel-like structures, are associated with selective atomic species partition and consequent nanoscale non-uniform composition gradient distribution at the subsurface. In conclusion, our findings provide fundamental insights on atomic-scale mechanisms of structural transformation in layered cathodes.

25 ENERGY STORAGE↗

Elucidating and Mitigating High-Voltage Degradation Cascades in Cobalt-Free LiNiO 2 Lithium-Ion Battery Cathodes

LiNiO 2 (LNO) is a promising cathode material for next-generation Li-ion batteries due to its exceptionally high capacity and cobalt-free composition that enables more sustainable and ethical large-scale manufacturing. However, its poor cycle life at high operating voltages over 4.1 V impedes its practical use, thus motivating efforts to elucidate and mitigate LiNiO 2 degradation mechanisms at high states of charge. Here, a multiscale exploration of high-voltage degradation cascades associated with oxygen stacking chemistry in cobalt-free LiNiO 2 , is presented. In this work, lattice oxygen loss is found to play a critical role in the local O3–O1 stacking transition at high states of charge, which subsequently leads to Ni-ion migration and irreversible stacking faults during cycling. This undesirable atomic-scale structural evolution accelerates microscale electrochemical creep, cracking, and even bending of layers, ultimately resulting in macroscopic mechanical degradation of LNO particles. By employing a graphene-based hermetic surface coating, oxygen loss is attenuated in LNO at high states of charge, which suppresses the initiation of the degradation cascade and thus substantially improves the high-voltage capacity retention of LNO. Overall, this study provides mechanistic insight into the high-voltage degradation of LNO, which will inform ongoing efforts to employ cobalt-free cathodes in Li-ion battery technology.

25 ENERGY STORAGE↗

Mesoscale Effective Property Simulations Incorporating Conductive Binder

Lithium-ion battery electrodes are composed of active material particles, binder, and conductive additives that form an electrolyte-filled porous particle composite. The mesoscale (particle-scale) interplay of electrochemistry, mechanical deformation, and transport through this tortuous multi-component network dictates the performance of a battery at the cell-level. Effective electrode properties connect mesoscale phenomena with computationally feasible battery-scale simulations. We utilize published tomography data to reconstruct a large subsection (1000+ particles) of an NMC333 cathode into a computational mesh and extract electrode-scale effective properties from finite element continuum-scale simulations. We present a novel method to preferentially place a composite binder phase throughout the mesostructure, a necessary approach due difficulty distinguishing between non-active phases in tomographic data. We compare stress generation and effective thermal, electrical, and ionic conductivities across several binder placement approaches. Isotropic lithiation-dependent mechanical swelling of the NMC particles and the consideration of strain-dependent composite binder conductivity significantly impact the resulting effective property trends and stresses generated. Lastly, our results suggest that composite binder location significantly affects mesoscale behavior, indicating that a binder coating on active particles is not sufficient and that more accurate approaches should be used when calculating effective properties that will inform battery-scale models in this inherently multi-scale battery simulation challenge.

25 ENERGY STORAGE↗

Effect of Catalyst and Catalyst Layer Composition on Catalyst Support Durability

Polymer electrolyte membrane fuel cells (PEMFCs) are efficient, zero-emission engines for the automotive sector. However, cost and durability are major barriers for the commercialization of PEMFCs. Degradation of the carbon support in the cathode catalyst layer due to high potential excursions caused by unmitigated events like H 2 starvation, or start-up/shutdown are still a major durability issue in PEMFCs. Catalyst support durability was studied by accelerated stress tests (ASTs) that included repeated potential cycling from 1.0 to 1.5 V. The effect of catalyst layer composition on carbon corrosion was studied using membrane electrode assemblies with different catalysts (Pt, PtCo), catalyst composition (catalyst wt.%, supports), ionomer composition (loading, and equivalent weights). The corrosion of the carbon support is similar between Pt and PtCo catalysts. However, the performance degradation rate is higher for the alloy catalysts due to differences in catalyst particle size and the transition metal’s leaching accelerating the performance degradation. The carbon loss is lower for catalysts with lower initial carbon loading (or higher catalyst wt.%), which is better for durability. However, the cumulative loss of carbon is identical for electrodes with the same catalyst support irrespective of catalyst and ionomer composition in the catalyst layer.

25 ENERGY STORAGE↗

Scalable synthesis of Na3V2(PO4)(3)/C porous hollow spheres as a cathode for Na-ion batteries

Na3V2(PO4)(3) (NVP) has been considered as a very promising cathode material for sodium-ion batteries (SIBs) due to its typical NASICON structure, which provides an open and three dimensional (3D) framework for Na+ migration. However, the low electronic conductivity of NVP limits its rate capability and cycling ability. In this study, carbon coated hollow structured NVP/C composites are synthesized via a template-free and scalable ultrasonic spray pyrolysis process, where the carbon coated NVP particles are uniformly decorated on the inner and outer surfaces of the porous hollow carbon spheres. When evaluated as a cathode material for SIBs, the unique NVP/C porous hollow sphere cathode delivers an initial discharge capacity of 99.2 mA h g(-1) and retains 89.3 mA h g(-1) after 300 charge/discharge cycles with a very low degradation rate of 0.035% per cycle. For comparison, the NVP/C composite, prepared by the traditional sol-gel method, delivers a lower initial discharge capacity of 97.4 mA h g(-1) and decreases significantly to 71.5 mA h g(-1) after 300 cycles. The superior electrochemical performance of NVP/C porous hollow spheres is attributed to their unique porous, hollow and spherical structures, as well as the carbon-coating layer, which provides a high contact area between electrode/electrolyte, high electronic conductivity, and high mechanical strength.

Mao, JF↗

Enhanced rate performance of Li3V2(PO4)3/C cathode by an improved rheological phase assisted microwave method

Highlights: • Rheological phase assisted microwave can utilize both advantages of two methods. • Polyethylene glycol was used as both rheological medium and carbon precursor. • 101.8 mA h g{sup −1} of specific capacity was obtained at 50 C rates. - Abstract: In this study, high-rate Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C composite is successfully synthesized via an improved rheological phase assisted microwave method using polyethylene glycol as both rheological medium and carbon precursor. The relatively uniform Li{sub 3}V{sub 2}(PO{sub 4}){sub 3} particles are encapsulated in amorphous carbon architecture to form core-shell structure, providing effective electron and ion transport. When used as a cathode material in lithium ion battery, the Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}/C composite displays a maximum discharge capacity of 101.8 mA h g{sup −1} at 50 C charge/discharge rate and still possesses 98.3% of capacity retention after 100 cycles, demonstrating superior rate capability and excellent cycling stability when compared with bare Li{sub 3}V{sub 2}(PO{sub 4}){sub 3}. The observed electrochemical performance could be attributed to uniform coated-carbon pyrolysis from polyethylene glycol rheological phase precursor and small Li{sub 3}V{sub 2}(PO{sub 4}){sub 3} pristine particles synthesized by the fast microwave heating route.

36 MATERIALS SCIENCE↗

Investigation of micro-structure and micro-hardness properties of 304L stainless steel treated in a hot cathode arc discharge plasma

We have established a hot cathode arc discharge plasma system, where different stainless steel samples can be treated by monitoring the plasma parameters and nitriding parameters independently. In the present work, a mixture of 70% N{sub 2} and 30% H{sub 2} gases was fed into the plasma chamber and the treatment time and substrate temperature were optimized for treating 304L Stainless Steel samples. Various physical techniques such as x-ray diffraction, energy dispersive x-ray spectroscopy and micro-vickers hardness tester were employed to determine the structural, surface composition and surface hardness of the treated samples.

36 MATERIALS SCIENCE↗

A Systematic Study on the Effects of Solvating Solvents and Additives in Localized High‐Concentration Electrolytes over Electrochemical Performance of Lithium‐Ion Batteries

Abstract Localized high‐concentration electrolytes (LHCEs) based on five different types of solvents were systematically studied and compared in lithium (Li)‐ion batteries (LIBs). The unique solvation structure of LHCEs promotes the participation of Li salt in forming solid electrolyte interphase (SEI) on graphite (Gr) anode, which enables solvents previously considered incompatible with Gr to achieve reversible lithiation/delithiation. However, the long cyclability of LIBs is still subject to the intrinsic properties of the solvent species in LHCEs. Such issue can be readily resolved by introducing a small amount of additive into LHCEs. The synergetic decompositions of Li salt, solvating solvent and additive yield effective SEIs and cathode electrolyte interphases (CEIs) in most of the studied LHCEs. This study reveals that both the structure and the composition of solvation sheaths in LHCEs have significant effect on SEI and CEI, and consequently, the cycle life of energetically dense LIBs.

Jia, Hao↗

Analysis of the electric field induced elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} by transmission electron microscopy

The chemical instability of line patterned Ge{sub 2}Sb{sub 2}Te{sub 5} was studied by transmission electron microscopy after electrically inducing melt and solidification. Compositional analysis showed elemental separation of Te to the anode side, while Ge and Sb mutually separated at the cathode side. Such elemental separation of Ge{sub 2}Sb{sub 2}Te{sub 5} is explained by the electric field effects and thermodynamic driving forces.

36 MATERIALS SCIENCE↗

Microstructure and temperature coefficient of resistance of thin cermet resistor films deposited from CrSi{sub 2}-Cr-SiC targets by S-gun magnetron

Technological solutions for producing nanoscale cermet resistor films with sheet resistances above 1000 {Omega}/{open_square} and low temperature coefficients of resistance (TCR) have been investigated. 2-40 nm thick cermet films were sputter deposited from CrSi{sub 2}-Cr-SiC targets by a dual cathode dc S-gun magnetron. In addition to studying film resistance versus temperature, the nanofilm structural features and composition were analyzed using scanning electron microscopy, atomic force microscopy, high-resolution transmission electron microscopy, energy-dispersive x-ray spectroscopy, and electron energy loss spectroscopy. This study has revealed that all cermet resistor films deposited at ambient and elevated temperatures were amorphous. The atomic ratio of Si to Cr in these films was about 2 to 1. The film TCR displayed a significant increase when the deposited film thickness was reduced below 2.5 nm. An optimized sputter process consisting of wafer degassing, cermet film deposition at elevated temperature with rf substrate bias, and a double annealing in vacuum, consisting of in situ annealing following the film sputtering and an additional annealing following the exposure of the wafers to air, has been found to be very effective for the film thermal stabilization and for fine tuning the film TCR. Cermet films with thicknesses in the range of 2.5-4 nm deposited using this technique had sheet resistances ranging from 1800 to 1200 {Omega}/{open_square} and TCR values from -50 ppm/ deg. C to near zero, respectively. A possible mechanism responsible for the high efficiency of annealing the cermet films in vacuum (after preliminary exposure to air), resulting in resistance stabilization and TCR reduction, is also discussed.

36 MATERIALS SCIENCE↗

Lithium Vanadium Oxide (Li 1.1 V 3 O 8 ) Coated with Amorphous Lithium Phosphorous Oxynitride (LiPON): Role of Material Morphology and Interfacial Structure on Resulting Electrochemistry

In the present work, lithium vanadium oxide (Li 1.1 V 3 O 8 ) particles synthesized at two different temperatures were coated with an amorphous lithium phosphorous oxynitride (LiPON) film for the first time, and the effects of the LiPON coating on the electrochemistry of the Li 1.1 V 3 O 8 materials with different morphologies were systematically investigated by comparing uncoated Li 1.1 V 3 O 8 and Li 1.1 V 3 O 8 coated with LiPON of various thicknesses. Galvanostatic discharge-charge cycling revealed increased functional capacity for the LiPON-coated materials. Post-cycling electrochemical impedance spectroscopy showed that LiPON-coated Li 1.1 V 3 O 8 materials developed less interfacial resistance with extended cycling, rationalized by vanadium migration into the LiPON coating seen by electron energy loss spectra. Post-mortem quantitative analysis of the anodes revealed more severe vanadium dissolution for the more irregularly shaped Li 1.1 V 3 O 8 materials with less LiPON coverage. Thus, this study highlights the specific benefits and limitations of LiPON coatings for stabilizing a moderate voltage Li 1.1 V 3 O 8 cathode material under extended cycling in liquid electrolyte, and describes a generally applicable approach for comprehensive characterization of a composite electroactive material which can be used to understand interfacial transport properties in other functional systems.

25 ENERGY STORAGE↗

The Science and Engineering of Durable Ultralow PGM Catalysts (2012 DOE-EERE-FCT Annual Progress Report)

Minimizing the quantity of Pt group metals used in polymer membrane fuel cells (PEMFCs) is one of the remaining grand challenges for fuel cell commercialization. Tremendous progress has been achieved over the last two decades in decreasing the Pt loading required for efficient fuel cell performance. Unfortunately, the fluctuations in the price of Pt represent a substantial barrier to the economics of widespread fuel cell use. Durability and impurity tolerance are also challenges that are tightly coupled to fuel cell Pt electrode loading. Traditional approaches to decreasing the amount of Pt required for good performance include: (1) Increasing mass activity by decreasing Pt particle size by supporting on carbon; (2) Alloy formulation Pt-Co, Pt-Cr alloys to improve mass activity; (3) Increasing Pt utilization by optimization of electronic and ionic contact of the Pt particles; (4) Improving conductivity of the electronic and ionic conducting constituents of the membrane electrode assembly; and (5) Improving reactant to and product mass transport away from the electroactive sites. Recent novel approaches include the nanoengineering of core shell catalysts and Pt particles of unusual geometries such as nanowires/whiskers. The success of the aforementioned approaches has been great; however further advances using such approaches have been hampered by a lack of underlining scientific understanding of the catalyst activity, particle growth mechanisms, and optimization strategies for designing composite electrodes The objectives of this report are: (1) Development of durable, high mass activity Platinum Group Metal (PGM) cathode catalysts-enabling lower cost fuel cells; (2) Elucidation of the fundamental relationships between PGM catalyst shape, particle size and activity to help design better catalysts; (3) Optimization of the cathode electrode layer to maximize the performance of PGM catalysts-improving fuel cell performance and lowering cost; (4) Understanding the performance degradation mechanisms of high mass activity cathode catalysts-provide insights to better catalyst design; and (5) Development and testing of fuel cells using ultra-low loading high activity PGM catalysts-validation of advanced concepts.

08 HYDROGEN↗

Disordered anodes for Ni-metal rechargeable battery

An electrochemical cell is provided that includes a structurally and compositionally disordered electrochemically active alloy material as an anode active material with unexpected capacity against a nickel hydroxide based cathode active material. The disordered metal hydroxide alloy includes three or more transition metal elements and is formed in such a way so as to produce the necessary disorder in the overall system. When an anode active material includes nickel as a predominant, the resulting cells represent the first demonstration of a functional Ni/Ni cell.

25 ENERGY STORAGE↗