Search NASA⌕ Search

SEARCH · Search NASA

Results for “distributed wind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Performance and test section flow characteristics of the National Full-Scale Aerodynamics Complex 80- by 120-Foot Wind Tunnel

Results from the performance and test section flow calibration of the 80- by 120-Foot Wind Tunnel are presented. Measurements indicating the 80- by 120-ft test section flow quality were obtained throughout the tunnel operational envelope and for atmospheric wind speeds up to approximately 20 knots. Tunnel performance characteristics and a dynamic pressure system calibration were also documented during the process of mapping the test section flow field. Experimental results indicate that the test section flow quality is relatively insensitive to dynamic pressure and the level of atmospheric winds experienced during the calibration. The dynamic pressure variation in the test section is within +/-75 percent of the average. The axial turbulence intensity is less than 0.5 percent up to the maximum test section speed of 100 knots, and the vertical and lateral flow angle variations are within +/-5 deg and +/-7 deg, respectively. Atmospheric winds were found to affect the pressure distribution in the test section only at high ratios of wind speed to test section speed.

Zell, Peter T.↗
NASA NTRS1972

Interstellar helium in interplanetary space

The velocity distribution function of He(+) in the solar wind at 1 AU is calculated with the assumption that the source is photoionization of a cold (T = 100 K), neutral interstellar wind. If the spiral magnetic field is noise free, the velocity distribution is diffuse and would not produce a peak at 4(E over Q) sub H in an E over Q particle spectrum. If the velocity of the interstellar wind with respect to the sun lies in the ecliptic, a large variation of the He(+) number density with respect to ecliptic longitude is expected.

Feldman, W. C.↗
DOE OSTI2021

Sensor enabled data-driven predictive analytics for modeling and control with high penetration of DERs in distribution systems

The electric power grid is undergoing a tremendous transformation due to the increasing penetration of renewable energy resources beginning with wind and more recently with the distributed energy resources (DERs) such as solar and battery storage. DERs have dramatically changed the role of the distribution systems in the overall power grid, and they are expected to contribute a significant portion of power generation in the future. If current trends for DERs continue, system operation and control will need to change dramatically for improved grid reliability and resiliency. As renewable resources increase in penetration, new and challenging operational, planning, and design problems are expected to emerge. Some of the key challenges that arise in the planning and operation of the future grid are: 1) Quantifying the impact of high DER penetration in distribution systems on bulk grid behavior over multiple time scales. 2) Identifying whether a particular DER configuration/settings have a large impact on the overall grid behavior. These challenges can be addressed in an offline manner using detailed T&D grid models and they can also be addressed in an online manner using sensor measurements. In particular, the advancement and planned growth in sensor technology in power grid over various voltage levels provide us with a unique opportunity to tackle these challenges from a data analytic perspective without needing detailed T&D grid models. A few questions that naturally arise when addressing the challenges from DERs using sensor data are: 1) How can we use limited sensor measurements to monitor & control voltage stability and small signal stability of the bulk system? 2) How can we ensure that the developed data analytic methods are robust to data availability and quality issues? 3) How can we compute the developed analytics in a scalable manner using streaming measurements? In this project, we addressed the aforementioned challenges arising from DERs and answered the questions raised above on how to effectively use the sensor measurements to enhance the reliability and performance of the electric grid. Thus, the overarching goal of this project is to develop effective reduced/representative system models from data that make the computational complexity sufficiently manageable so as to be useful to simulate, analyze, and even control complex non-linear power systems dynamics with large penetrations of DERs. In order to achieve the objective, the project team established a four-fold technical approach 1) Formulated a combined transmission-distribution co-simulation framework for data generation and validation, 2) Derived reduced/representative models of power systems based on data-driven methods for efficient computation and appropriate representation of system behavior, 3) Developed data driven characterization of power system behavior based on transfer operator theory, machine learning and optimization for model estimation, 4) Incorporated a scalable data management and processing architecture using distributed Kafka streaming applications that coordinate input data streams to the developed data analytics. The key accomplishments of the project are: 1) Development of a scalable multi-timescale T&D co-simulation framework (both for steady state and for dynamic co-simulation) using commercial solvers (PSSE and GridLAB-D). The steady-state T&D co-simulation interface is shared with our industry partner (PJM). 2) A structured reduced order dynamic model of distribution systems that can represent partial motor stalling along with a systematic procedure to derive the model parameters. 3) A PMU based online method to monitor, localize and mitigate fault-induced delayed voltage recovery using DER reactive support and load control in distribution systems. 4) Development of linear operator based robust methodologies for dynamic state estimation, uncertainty quantification, system identification and trajectory prediction for power system dynamics. 5) An adaptive damping control for utilizing wind energy resources to provide oscillation damping and system stability. 6) Implementation of Kafka-based framework for efficient processing of streaming data using Linux-based local virtual environment.

DER integration↗
NASA NTRS1959

Chordwise Pressure Distributions over Several NACA 16-Series Airfoils at Transonic Mach Numbers up to 1.25

A two-dimensional wind-tunnel investigation of the pressure distributions over several NACA 16-series airfoils with thicknesses of 4, 6, 9, and 12 percent of the chord and design lift coefficients of 0, 0.2, 1 and 0.5 has been conducted in the Langley airfoil test apparatus at transonic Mach numbers from 0.7 to 1.25. The tests ranged in Reynolds number from 2.4 x 10 (exp 6) to 2.8 x 10 (exp 6) and in angle of attack from -10 to 12 degrees. Chordwise pressure distributions and schlieren flow photographs are presented without analysis.

Ladson, Charles L.↗
NASA NTRS1979

An empirical polytrope law for solar wind thermal electrons between 0.45 and 4.76 AU: Voyager 2 and Mariner 10

Empirical evidence is presented that solar wind thermal electrons obey a polytrope law with polytrope index gamma = 1.175 plus or minus 0.03. The Voyager 2 and Mariner 10 data used as evidence are compared and discussed. The theoretical predictions that solar wind thermal electrons in the asymptotic solar wind should obey a polytrope law with polytrope index gamma = 1.16 plus or minus. The widespread impressions in the literature that solar wind electrons behave more like an isothermal than adiabatic gas, and the arguments that Coulomb collisions are the dominant stochastic process shaping observed electron distribution functions in the solar wind are reexamined, reviewed and evaluated. The assignment of the interplanetary potential as equal to approximately seven times the temperature of the thermal electrons is discussed.

Sittler, E. C., Jr.↗
NASA NTRS1971

Average solar wind proton properties from Pioneers 6 and 7.

Distributions and average values for the proton speed, azimuthal and polar flow directions, and the proton temperature and density in the solar wind are presented. The data are obtained from the Ames plasma probes on Pioneers 6 and 7. The time periods covered include Dec. 18, 1965 to mid-February 1966, and mid-August to mid-October 1966. The distributions of the parameters, except for the polar flow direction, are skewed, partially because of stream-stream interactions in the solar wind. The average values of the basic plasma parameters from the two spacecraft are different which could be due partially to different solar activity at the two times, and partially to sector and beam structure dependence.

Mihalov, J. D.↗
NASA NTRS1978

A simple method for obtaining a three-dimensional proton distribution function from Voyager plasma data

The main sensor of the Vogager plasma experiment consists of a cluster of three, modulated-grid Faraday cups whose normals are arranged symmetrically about the symmetry axis of the cluster at an angle of 20 degrees to that axis. In interplanetary space, each cup explores the positive ion distribution by accepting particles from contiguous slices in velocity space. The slices are narrow in the direction of the normal to the modulating grid but are broad in planes parallel to that grid. The resulting three sets of measurements can be combined to yield the three-dimensional distribution function in the following way: the distribution function is assumed to be gyrotropic. For each value of speed in a frame of reference moving with the bulk velocity of the solar wind, the variation of the distribution function with angle from the field direction is represented by a series of Legendre polynomials. Effects such as double-streaming and heat flow can be well represented by using only the first three terms of the series which are fully specified by the measurements. Examples of the use of this method in the analysis of Voyager data are shown.

Olbert, S.↗
NASA NTRS1988

Comparison of pressure distributions on model and full-scale NACA 64-621 airfoils with ailerons for wind turbine application

The aerodynamic similarity between a small (4-inch chord) wind tunnel model and a full-scale wind turbine blade (24-foot tip section with a 36-inch chord) was evaluated by comparing selected pressure distributions around the geometrically similar cross sections. The airfoils were NACA 64-621 sections, including trailing-edge ailerons with a width equal to 38 percent of the airfoil chord. The model airfoil was tested in the OSU 6- by 12-inch High Reynolds Number Wind Tunnel; the full-scale blade section was tested in the NASA Langley Research Center 30- by 60-foot Subsonic Wind Tunnel. The model airfoil contained 61 pressure taps connected by embedded tubes to pressure transducers. A belt containing 29 pressure taps was fixed to the full-scale section at midspan to obtain surface pressure data. Lift coefficients were obtained by integrating pressures, and corrections were made for the 3-D effects of blade twist and downwash in the blade tip section. The results of the two different experimental methods correlated well for angles of attack from minus 4 to 36 degrees and aileron reflections from 0 to 90 degrees.

Gregorek, G. M.↗
DOE OSTI2022

Unleashing the Frequency: Multi-Megawatt Demonstration of 100% Renewable Power Systems with Decentralized Communication-Less Control Scheme

Power systems, which range in size from small microgrids to island systems to large regional grids, are typically managed by a central controller that requires complex communication methods and can be unreliable and pose cyber security risks in certain applications, especially when controlling a larger number of nodes. We propose an inherently robust, scalable method of integration using multiple energy storage systems and distributed energy resources, which does not require any means of dedicated communication. This method moves beyond the paradigm of controlling grid frequency at a fixed value (e.g., 60 Hz), instead allowing the frequency to fluctuate within certain limits (e.g., 59.6-60.4 Hz). With a greater operating range, the frequency can carry necessary information from energy storage systems to highly variable distributed energy resources like photovoltaics, wind, hydro, etc.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Atmospheric particle abundance and sea salt aerosol observations in the springtime Arctic: a focus on blowing snow and leads

Abstract. Sea salt aerosols play an important role in the radiation budget and atmospheric composition over the Arctic, where the climate is rapidly changing. Previous observational studies have shown that Arctic sea ice leads are an important source of sea salt aerosols, and modeling efforts have also proposed blowing snow sublimation as a source. In this study, size-resolved atmospheric particle number concentrations and chemical composition were measured at the Arctic coastal tundra site of Utqiaġvik, Alaska, during spring (3 April–7 May 2016). Blowing snow conditions were observed during 25 % of the 5-week study period and were overpredicted by a commonly used blowing snow parameterization based solely on wind speed and temperature. Throughout the study, open leads were present locally. During periods when blowing snow was observed, significant increases in the number concentrations of 0.01–0.06 µm particles (factor of 6, on average) and 0.06–0.3 µm particles (67 %, on average) and a significant decrease (82 %, on average) in 1–4 µm particles were observed compared to low wind speed periods. These size distribution changes were likely caused by the generation of ultrafine particles from leads and/or blowing snow, with scavenging of supermicron particles by blowing snow. At elevated wind speeds, both submicron and supermicron sodium and chloride mass concentrations were enhanced, consistent with wind-dependent local sea salt aerosol production. At moderate wind speeds below the threshold for blowing snow as well as during observed blowing snow, individual sea spray aerosol particles were measured. These individual salt particles were enriched in calcium relative to sodium in seawater due to the binding of this divalent cation with organic matter in the sea surface microlayer and subsequent enrichment during seawater bubble bursting. The chemical composition of the surface snowpack also showed contributions from sea spray aerosol deposition. Overall, these results show the contribution of sea spray aerosol production from leads on both aerosols and the surface snowpack. Therefore, if blowing snow sublimation contributed to the observed sea salt aerosol, the snow being sublimated would have been impacted by sea spray aerosol deposition rather than upward brine migration through the snowpack. Sea spray aerosol production from leads is expected to increase, with thinning and fracturing of sea ice in the rapidly warming Arctic.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1978

An analysis of maximum horizontal wind speeds recorded since 1961 at Kennedy Space Center, Florida

Tabulations of maximum horizontal wind speed values are reported that were recorded at the Kennedy Space Center. Maximum wind speeds were recorded during the eight hurricanes which have affected the area--Cleo in August 1964 through Agnes in June 1972. Detailed tabulations and frequency distributions of daily maximum horizontal wind speeds recorded at NASA's 150 m ground tower facility at nine levels from December 1965 through March 1970 are also included.

Alexander, M. B.↗
NASA NTRS2004

The Wind and Temperature Spectrometer (WTS) in the Atmospheric Neutral Density Experiment (ANDE) Satellite

Miniaturization efforts in new spectrometers for ionosphere/thermosphere investigations of the ion-drifts and neutral winds and corresponding temperatures make possible very light (about 250 g) packages consuming less than 0.4 W. Previously described, our approach measures the angular and energy distributions of neutral atoms and molecules (or ions) in two perpendicular planes; using those distributions to determine the full wind vector, the temperature and the relative densities of O and N2, as required for the ANDE mission. The measurements require two separate electron impact ion sources each with its own electron beam cathode. We have developed a low-temperature thermionic emission cathode that delivers 1 mA electron current at 80 mW power, making it possible to operate neutral wind-temperature experiments for the first time with powers less than 0.5 W. Advances in the ion optics of the energy-angle spectrometer enhance the energy resolution-aperture product more than a factor of 3 to enable energy resolutions of a few percent with large apertures. With these technology improvements it is now possible to obtain the full neutral wind vector, temperature and O/N2, density ratio once per second in a 250g/0.4W package with sensitivity up to about 500 km altitude in the thermosphere. We will describe the WTS as deployed in ANDE and show simulated data with the non-linear least squares analysis to illustrate expected performance of the WTS in the estimated errors in the three components of the wind, the temperature, and the relative densities.

Herrero, F. A.↗
NASA NTRS1995

Theoretical Plasma Distribution Consistent With Ulysses Magnetic Field Observations in a High-Speed Solar Wind Tangential Discontinuity

The overall multi-layer structure of the magnetic field observed by Ulysses across a broad solar wind tangential discontinuity can be reproduced fairly well by means of a kinetic model. Such a simulation provides complementary information about the velocity distribution functions, which are not always known due to the low time resolution inherent in plasma measurements. The success of such a simulation proves that our kinetic model can be used as a realistic basis for further studies of the structure and stability of tangential discontinuities.

solar wind Ulysses plasma↗
NASA NTRS1992

Nozzle/Diffuser For Test Section Of Wind Tunnel

Nozzle-diffuser improves distribution of flow in test section and increases recovery of pressure in first diffuser. Has rectangular or circular cross section like contraction duct just upstream of test section and is, in effect, extension of contraction duct. Because flow returning to fan at higher pressure, less fan power needed to maintain same rate of flow.

Barna, P. Stephen↗
NASA NTRSDate not supplied

SURFACE EXOSURE TIMESCALES OF APOLLO CORE SAMPLE 73002 SPACE WEATHERED GRAINS

Introduction: Space weathering causes the surface regolith on airless bodies like the Moon to be morphologically, microstructurally, and chemically altered due to micrometeoroid bombardment and solar wind irradiation[1]. These processes produce a multitude of microstructural and chemical changes in individual soil grains that accumulate as grains are exposed on the surface over time. One microstructural feature produced by exposure to the solar wind is the development of ion-damaged rims on regolith grains via H+ and He+ ion irradiation. Also present are solar energetic particle (SEP) tracks, which are nanoscale lineations of ionization damage within grain interiors formed by high energy solar flare ions(primarily Fe group nuclei) which penetrate millimeters below the surface [2]. Recent work has confirmed that the thickness of solar wind-damaged amorphous rims on anorthite grains, nanocrystalline rims on olivine grains, and their respective SEP track densities are correlated with their surface exposure ages [3].Core sample 73002, recently released under the Apollo Next Generation Sample Analysis (ANGSA) Program, has provided an opportunity to study material collected from the light mantle formation during Apollo 17. The light mantle is thought to have been deposited via a landslide originating from the neighboring South Massif [4]. Spectral profiles and ferromagnetic resonance measurements of bulk soils sampled at cm-intervals from 73002 indicate the existence of mature regolith extending ~8 cm below the surface, suggesting the presence of an in-situ reworking zone in the core[5,6].Here we present the distribution of SEP track densities, solar wind damaged rim widths, and the corresponding surface exposure ages of grains residing in the proposed in-situ reworking zone of core 73002. Methods: Bulk samples of regolith from the first eight intervals and every following fourth interval down the core (dissection Pass 2) were delivered to Purdue University as <45 μm size fractions. The first eight0.5 cm intervals, representing the top 4cmof regolith, were individually dry sieved to a<20 μm size fraction, and grains were prepared by ultramicrotomy for analysis in the scanning transmission electron microscope (STEM). Bright field (BF) and dark field (DF) STEM images of solar flare tracks and solar wind damaged rims were acquired on a JEOL 2500SE TEM, equipped with a 60 mm2ultra-thin window silicon drift energy dispersive X-ray (EDX) spectrometer at NASA John-son Space Center. Grain compositions were determined by EDX compositional spectrum imaging. SEP track densities and amorphous rim thicknesses were measured on BF and DF images. Results: The fraction of grains with discernable space weathering features decreased with depth, with 100% in the first interval exhibiting space weathering features as opposed to ~60% in Interval 8.BF and DF STEM images show splash-melt and vapor deposited rims on outermost grain margins with embedded Fe-bearing nanoparticles ranging in size up to ~10 nm in diameter. Images also show solar-wind damaged rims below the vapor deposits, and SEP tracks present in grain interiors. The rim thicknesses and SEP track densities were determined using the methods of [3] for 54grains spanning the top 4 cm. ~80% of the grains analyzed were anorthite and ~20% were olivine. The track production rate from[3] was used to estimate the surface exposure times of the grains in this study. The majority of exposure times are in the 1 -5 MY range for all intervals. The lowest value was 3.8x 10¬5years in Interval 8and the highest value was1.1x 107years in Interval 6. Grains with the highest solar wind damage rim thicknesses and SEP track densities are found in Interval 6.The highest rim thickness and track density observed for anorthiteis126.5 nm and4.7 x 1011tracks/cm2, while for olivine they are 98.6 nm and 1.83 x 1011tracks/cm2, respectively. Discussion: Intervals from the top 4 cm of 73002 show similar SEP track density and solar wind damaged rim thickness distributions. Spectral and ferromagnetic resonance measurements of 73002 indicate an in-situ reworking zone up to~8 cm below the surface[5,6].The depth analyzed in this work is within the core’s uppermost in-situ reworking zone and may serve as an explanation to the homogenous distribution of exposure ages. The decreasing abundance of space weathered features with depth is consistent with regolith mixing models showing an exponential decay in regolith maturity with depth over time[7].A maximum surface exposure age determined via SEP track density is approximately 10million years. This timescale is consistent with the lower estimate of surface exposure ages of the light mantle determined in previous studies, which can range from 10s to over 100 Ma [4].It also falls within the core regolith reworking development timescale of ~17 Ma [5,6]. Additional analysis will be performed for a further seven intervals in 73002.

J A McFadden↗
NASA NTRSDate not supplied

TROPOMI Geometry-dependent Lambertian-Equivalent surface Reflectivity (GLER) Product for Improved Trace-Gas Retrieval

Accurate information about the reflectivity of the Earth's surface is required for most satellite retrievals of atmospheric composition, and this information is generally taken from monthly surface reflectivity climatology that neglects angular dependence. Previously we introduced Geometry-dependent Lambertian-equivalent surface reflectivity (GLER) which captures solar and satellite viewing angle dependence as well as daily and seasonal changes. GLER is calculated from simulations of Rayleigh-only top-of-atmosphere (TOA) radiances over non-Lambertian surfaces. We use NASA's Moderate Resolution Imaging Spectroradiometer (MODIS) bidirectional reflectance distribution function (BRDF) product over land and the wind-dependent Cox–Munk wave-facet slope distribution including water-leaving radiance over water to accounts for surface BRDF. We have developed global GLER product, previously for the Ozone Monitoring Instrument (OMI) and recently for Sentinel-5 Precursor (S5P) TROPOspheric Monitoring Instrument (TROPOMI) with several new improvements and updates. We have implemented the near real time daily V006 MODIS MCD43C1 BRDF data and gap-filled with a daily BRDF coefficient climatology created from 2002-2017 V006 MCD43GF data. The NASA’s Global Modelling Initiative hourly 0.25 x 0.25 deg Replay simulations are used for more accurate determination of pixel specific terrain pressure. To improve detection of seasonal snow/ice scenes, we use the 4-km snow cover product from the Interactive Multi-sensor Snow and Ice Mapping System (IMS). Finally, we use an improved version of the vector linearized discrete ordinate radiative transfer (VLIDORT) for update of the top-of-atmosphere (TOA) radiance look-up-tables (LUTs). We demonstrate how the use of GLER is beneficial to TROPOMI’s high spatial resolution (up to 3.5 km x 3.5 km) measurements to monitor atmospheric trace gas pollutants down to the sub-city scale.

TROPOMI↗
DOE OSTI2020

New Technologies for Power System Operation and Analysis, 1st Edition

New Technologies for Power System Operation and Analysis considers the very latest developments in renewable energy integration and system operation, including electricity markets and wide-area monitoring systems and forecasting. Helping readers quickly grasp the essential information needed to address renewable energy integration challenges, this new book looks at basic power system mathematical models, advanced renewable integration and system optimizations from transmission and distribution system sides. Sections cover wind, solar, gas and petroleum, making this a useful reference for all engineers interested in power system operation.

electricity markets↗