Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastic modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Recrystallization of A Shot Peened Single Crystal Nickel-Base Superalloy

Single crystal nickel-base superalloys used as turbine engine airfoils can have much higher creep and thermal fatigue resistance required for blades and vanes than polycrystalline superalloys due to the absence of weak grain boundaries, as well as the low elastic modulus in the [001] single crystal growth direction (Refs. 1 and 2). This has allowed an increase in the turbine rim inlet temperatures for improved performance and efficiency. However, these advantages in performance require constraints on acceptable levels of single crystal defects, such as macroscopic grain boundaries at low angles to the primary grain (i.e., low angle boundaries or LAB), higher angle boundaries, small new grains nucleated at the blade surface (a.k.a. freckles), larger new grains, and also the single crystal blades’ orientation, typically degrees off of the [001] direction and the orientation of a transverse [010] direction with respect to blade geometry. Therefore, single crystal turbine airfoils, which are frequently used with as-cast surfaces, are grain etched and inspected before and after heat treatments to ensure these aspects conform to acceptability limits.

single crystal↗

Using Digital Image Correlation for Quantifying Load Induced in Elastomers at Cryogenic Temperatures

Elastomers have glass transition temperatures (TG) that are well below room temperature. Below this temperature, elastomers can suddenly exhibit significantly different mechanical properties than those exhibited at warmer temperatures. A unique test was developed to measure the induced load generated by elastomers that have been gripped on both ends and cooled to cryogenic temperatures. The test simulates a space flight critical component that will result in loss of vehicle if the elastomer separates from the gripped end. Digital image correlation (DIC) was used to measure the strain on the material surface and the displacement of the grips during testing. Two cameras were mounted on an isolated tripod to capture images through optical glass fitted on the thermal chamber. DIC measurements were used to measure the elastic modulus, coefficient of thermal expansion, and the loads at the gripped ends, above and below the TG. There was nearly no load developed while the temperature was above the TG but loads rapidly increased two orders of magnitude as the temperature dropped below the TG.

Matlock Mennu↗

Radiation-Resistant Ti/BN Coatings: Insights From 171 Days Exposure to Space Radiation and Atomic Oxygen in Low Orbit

Atmospheric Plasma Spray (APS) and Vacuum Plasma Spray (VPS) techniques were used to develop Ti/2 vol.% hBN coatings, for extreme space environments and tested aboard the International Space Station as part of the MISSE-17 (Materials International Space Station Experiments) program. The coatings were exposed to atomic oxygen, space radiation, and low-orbit thermal cycling. VPS coatings showed a 56% increase in microhardness, a 26% rise in elastic modulus, minimal porosity and crack density changes compared to APS coatings. The change in mechanical properties is attributed to the formation of TiO, TiO₂ and TiN from nitrogen retention, alongside radiation-induced dislocations, which enhanced surface hardening. The oxidation of titanium led to the formation of TiO and TiO₂, while boron nitride was retained and underwent transmutation in VPS coatings. XPS and EDS analyses confirmed the enhanced space-environment resistance of VPS coatings, making them ideal for long-term spacecraft protection in lunar and Martian conditions.

Abhijith Kunneparambil Sukumaran↗

Thermal Degradation Behavior of Siloxane Elastomer Impregnated Carbon Nanotube Areogel Networks

A novel class of nanoporous graphitic carbon foams has been synthesized. Unprecedented properties - electrically conductive, thermally stable (> 1000 C), and mechanically robust. Improved transport properties (DWNT-CA, SWNT-CA) - greater than 100% enhancement in thermal conductivity, 100-400% improvement in electrical conductivity. Rich mechanical deformation behavior (SWNT-CA) - stiff ({approx}100% improvement of elastic modulus), energy dissipation, fracture toughness, and fatigue behavior. Implications for energy-related technologies - hydrogen storage, fusion and fission energy, catalysis, electrochemical energy storage, and composites with foam scaffolds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved rubber nanofillers

During this task, Silane functionalized TiO2 and HK3Ti4O4(SiO4)3 were sent to Goodyear (GY) for testing. These materials were characterized based on their interaction with the model elastomer, squalene. The Van der Waals interactions and Hamaker Constants for ZnO particles in squalene and rubber materials were characterized and it was determined that a 10-20 nm spacing was necessary between primary filler particles to maintain a stable nanocomposite. Contact angle measurements on the ZnO and ZnO-silane materials indicated that the solvent should wet the particles, and solvophobic attractions should not be present. These studies showed that the surface modification with sulfosilane coupling agents was successful, and high levels of dispersion of the particles remained possible. Further, a novel surface charging phenomenon where negative surface charging is developed in the squalene environment was observed and corroborated by measurements of particle size and of the surface modified materials in squalene. This impacts the dispersion of the particles according to the traditional colloidal interpretation of electrostatic repulsive forces between particles. Additionally, thin nanocomposite fibers were developed using electrospinning. The size and shape of the oxides did not change during the electrospinning process, although the shape of the fiber and the distribution of the particles, particularly for ZnO, was not ideal. There was an obvious increase in elastic modulus and hardness from the addition of the oxides, but differentiating the oxides, and particularly the surfactants, was difficult. The A-1289 lead to the greatest dispersion of the filler particles, while the A-1589 and the NXT produced clustered particle aggregates. This agrees with previous study of these materials in low molecular weight squalene solvent studies reported earlier. The behavior of the nanoparticle ZnO and the microparticle silica is different as well, with the ZnO being contained within the elastomer, and the SiO2 forming monolayers at the surface of the elastomer. The dynamic mechanical analysis did not show clear trends between the surface modification and the aggregate structure. In the silica particles, the NXT led to the least particle interaction, followed by the A-1289 and highest particle interaction found for the A-1589. For the nanosized ZnO, the best dispersion was found for the A-1589, with both the A-1289 and NXT exhibiting frequency dependent responses.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Complementary effects of multi-protein components on biomineralization in vitro

The extracellular matrix (ECM) is composed of mixed protein fibers whose precise composition affects biomineralization. New methods are needed to probe the interactions of these proteins with calcium phosphate mineral and with each other. Here we follow calcium phosphate mineralization on protein fibers self-assembled in vitro from solutions of fibronectin, elastin and their mixture. We probe the surface morphology and mechanical properties of the protein fibers during the early stages. The development of mineral crystals on the protein matrices is also investigated. In physiological mineralization solution, the elastic modulus of the fibers in the fibronectin-elastin mixture increases to a greater extent than that of the fibers from either pure protein. In the presence of fibronectin, longer exposure in the mineral solution leads to the formation of amorphous calcium phosphate particles templated along the self-assembled fibers, while elastin fibers only collect calcium without any mineral observed during early stage. TEM images confirm that small needle-shape crystals are confined inside elastin fibers which suppress the release of mineral outside the fibers during late stage, while hydroxyapatite crystals form when fibronectin is present. These results demonstrate complementary actions of the two ECM proteins fibronectin and elastin to collect cations and template mineral, respectively.

36 MATERIALS SCIENCE↗

Solid electrolyte material manufacturable by polymer processing methods

The present invention relates generally to electrolyte materials. According to an embodiment, the present invention provides for a solid polymer electrolyte material that is ionically conductive, mechanically robust, and can be formed into desirable shapes using conventional polymer processing methods. An exemplary polymer electrolyte material has an elastic modulus in excess of 1.times.10.sup.6 Pa at 90 degrees C. and is characterized by an ionic conductivity of at least 1.times.10.sup.-5 Scm-1 at 90 degrees C. An exemplary material can be characterized by a two domain or three domain material system. An exemplary material can include material components made of diblock polymers or triblock polymers. Many uses are contemplated for the solid polymer electrolyte materials. For example, the present invention can be applied to improve Li-based batteries by means of enabling higher energy density, better thermal and environmental stability, lower rates of self-discharge, enhanced safety, lower manufacturing costs, and novel form factors.

36 MATERIALS SCIENCE↗

Measurement of Interfacial Adhesion in Glass-Epoxy Systems Using the Indentation Method

The adhesion of coatings often controls the performance of the substrate-coating system. Certain engineering applications require an epoxy coating on a brittle substrate to protect and improve the performance of the substrate. Experimental observations and measurements of interfacial adhesion in glass-epoxy systems are described in this thesis. The Oliver and Pharr method was utilized to calculate the bulk epoxy hardness and elastic modulus. Spherical indentations were used to induce delaminations at the substrate-coating interface. The delamination sizes as a function of load were used to calculate the interfacial toughness. The interfacial fracture energy of my samples is an order of magnitude higher than a previous group who studied a similar glass-epoxy system. A comparison study of how different glass treatments affect adhesion was also conducted: smooth versus rough, clean versus dirty, stressed versus non-stressed.

36 MATERIALS SCIENCE↗

Analytical Model Methodology Development and Demonstration of Approach on Used Fuel Performance Characterization for Condition of Normal Transportation

U.S. Nuclear Regulatory Commission (NRC) rules require that used nuclear fuel (UNF) rods maintain their integrity during handling, transportation, and storage to ensure maintenance of the fuel retaining boundary, safety against criticality, and long term fuel retrievability for processing and disposal. Consequently, understanding the mechanical performance of UNF rods under cumulative loading stemming from handling, normal conditions of transport (NCT), and normal conditions of storage (NCS) is necessary as their performance under these conditions establishes part of their safety basis. The U.S. Department of Energy (DOE) commissioned a multi-laboratory team consisting of subject matter experts at Pacific Northwest National Laboratory, Idaho National Laboratory, Sandia National Laboratory, and Oak Ridge National Laboratory to develop a methodology to examine the structural performance and potential for failure of UNF under NCT and to perform a demonstration of this methodology for a typical UNF transportation campaign. This team prepared a Research, Development, and Demonstration (RD&D) Plan that describes a methodology, including development and use of analytical models, to evaluate loading and associated mechanical responses of UNF rods and key structural components during NCT. The initial scope of this plan has now been fully executed. The demonstration of the methodology laid out in the RD&D plan is focused on structural performance evaluation of Westinghouse Electric 17×17 OFA pressurized water reactor fuel assemblies with a discharge burnup range of 30 58 GWd/MTU (assembly average), loaded in a representative high-capacity (=32 fuel rod assemblies) transportation package and transported on a 3000 mile rail journey. In general, the modeling and simulation approach consists of three levels; the cask level, the fuel assembly level, and the fuel rod level. This modeling approach utilized finite element analysis sub-modeling techniques to accurately model the complete spent nuclear fuel transport system on the railcar (cask restraint structure, cask, basket, assembly, and fuel rods). The sub-modeling approach allows for more detailed finite element models of individual system components, faster analysis run times for the individual sub-models, and flexibility when updating or modifying the sub-models to incorporate better excitation data, initial material properties, or other pertinent information. The final results of the initial demonstration are that cladding strains were not large enough to cause structural failure, but cyclic strains roughly projected for the entire route were significant in some cases. The number of cycles that the model hits certain strain "bins" are counted. These are extrapolated for a 3000 mile trip and the damage ratio is calculated which is the number of cycles the fuel rods hit certain strain bins over the 3000 mile journey divided by the number of cycles to failure. Under the final model and set of inputs, the total damage from summation of the worst shock and vibration cases is ~18% of the expected fatigue limit. Therefore the fuel rods are not expected to fail during NCT given the assumptions listed. Additionally, a number of sensitivity studies were performed. It was found that the areas of highest sensitivity were the cladding elastic modulus, the spacer grid stiffness, the spacer grid location, and gaps between the assembly and the cask; these findings can be used to guide future work.

Used Nuclear Fuel, Storage, Transportation, Normal↗

MICRO-CELLULOSE FIBER REINFORCED BIOCOMPOSITES FOR ADDITIVE MANUFACTURING

Polymer additive manufacturing (AM) technology is rapidly growing and it is transitioning from being primarily a prototyping method to an advanced manufacturing technique. Melt extrusion/fused deposition modeling, a method in which molten thermoplastic-based feedstock material is deposited in a raster pattern layer by layer, is the most commonly used technique in polymer AM. The technique enables direct digital manufacturing of desired geometry with controlled anisotropic distribution of reinforcing phase. While thermoplastic composites are being used in many areas of industry including AM, due to increasing environmental and long-term sustainability concerns, there is an increasing interest in bio-based renewable alternatives. Nano-to-mm scale plant-based fibers are utilized to improve properties of thermoplastics and produce bio-composites. The effect of commercially available micro-scale cellulose fibers (MFC) on the mechanical and rheological behavior of polylactic acid to produce fully bio-based composites are being investigated and selected formulations will be 3D-printed to investigate the effect of printing process on MFC alignment. Significant increases in both tensile strength and elastic modulus of compression-molded MFC-PLA composites were observed at 40 % (by wt) fiber levels.

Tekinalp, Halil↗

AGC 4 Graphite Specimen Postirradiation Characterization Plan

This characterization plan describes the thermal, physical, and mechanical measurement techniques that will be used to characterize graphite samples being tested in the fourth Advanced Graphite Creep experiment (AGC-4). Instruments, fixtures, and methods are currently in place for both pre and postirradiation material property measurements of bulk density, thermal diffusivity, coefficient of thermal expansion, elastic modulus, and electrical resistivity. Postirradiation testing procedures used to characterize the samples are described and discussed in the plan. Where they exist, American Society for Testing and Materials (ASTM) International testing standards will apply to the tests. Any departure from ASTM International testing standards or the approved laboratory procedures are documented within this characterization plan. Deviations that occur during testing will be documented in data reports.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanical Characterization of Loblolly Pine

Biorefineries are faced with various material flow challenges during feeding and handling, due to inherent variability and inhomogeneity of biomass feedstocks. This impacts the efficiency of refinery processes and unit operations. Proper characterization of bulk properties allows for optimal process design and reduction of overall costs. This work is aimed at evaluating the physical and mechanical properties that impact bulk flow of loblolly pine. Cyclic axial compression tests are performed to elucidate consolidation behavior under different stress conditions. The results are then used to develop correlations between material parameters (particle size, tissue type, moisture content) and Elastic Modulus of bulk samples.

09 BIOMASS FUELS↗

Characterization of Annealing-Induced Phase Segregation in Composite Silicon Anodes for Li-ion Batteries

Silicon (Si) anodes present a promising alternative to graphite anodes for lithium-ion batteries (LIBs), as Si has a greater specific capacity. However, one major constraint is the volumetric change of Si during lithiation that results in an unstable solid-electrolyte interphase (SEI), so Si-containing electrodes require the use of various strategies to mitigate these effects and improve performance. One such solution is the use of Si nanoparticles (NPs) that maximize the surface area to volume ratio. Here, we discuss electrodes made with Si NPs treated with polyethylene oxide (PEO) (for improving dispersion during processing), conductive carbon NPs, and P84 polyimide binder which shows significant impacts of annealing treatment on improvements of active material utilization, first cycle efficiency, and capacity retention with extensive cycling . We used air-free argon ion polishing to create electrode cross sections and imaged through the electrode thickness using atomic force microscopy (AFM)-based nano-electrical characterization of scanning spreading resistance microscopy (SSRM), nano-mechanical characterizations of contact resonance and force volume (CR-FV), and scanning electron microscopy-based energy dispersive x-ray spectroscopy (SEM-EDS). Results show that the Si and conductive carbon segregate into phases with a distinctive carbon-rich banded morphology that surrounds the Si-rich phase during annealing. In pristine electrodes, the carbon- and SEI-rich bands exhibit a higher electronic conductivity and a lower elastic modulus than the Si active material phase. These structures, as well as distinct electronic and mechanical properties, remain during cycling, suggesting an improvement of electrical conduction pathways and a mechanical strain buffer for active Si material expansion during cycling. This phase separation may be a major factor in the improvement seen in electrochemical performance due to annealing. Additionally, our nm-scale and multi-mode characterizations provide a novel route for understanding and improving energy storage devices, which is advantageous due to the highly inhomogeneous of composite electrodes in nm-mm scales.

ENERGY STORAGE↗

The Effect of Artificial SEIs on Lithium Metal Anode Morphology and Conductivity

Lithium metal has often been termed the “holy grail” of battery technology, due to its high capacity (2,061 mAh/cm3) and low electrochemical potential (-3.04 V vs. SHE). However, lithium’s beneficially low potential also causes it to be highly reactive in the presence of organic solvents, making it difficult to harness the high energy capabilities for rechargeable batteries. Common failure of lithium metal batteries occurs by rapid dendrite growth leading to a hazardous short-circuit. Various methods have been brought forth to better understand the fundamental mechanisms of lithium metal batteries, as well as modifications made to better stabilize lithium metal. A common route of modification is done through interface engineering, with attempts to artificially provide a stable, homogeneous solid-electrolyte interface (SEI). The stability of the SEI has direct effects on the heterogeneity of the electrode surface, which initiates a waterfall effect of for progressive reactions such as dendrite growth, dead lithium accumulation, and electrolyte consumption. This work aims to produce a mixed LiI-LiF artificial SEI to improve ionic conductivity while retaining a high elastic modulus.

25 ENERGY STORAGE↗

First Results from Nanoindentation of Vapor Diffused Nb3Sn Films on Nb

The mechanical vulnerability of the Nb3Sn-coated cavities is identified as one of the significant technical hurdles toward deploying them in practical accelerator applications in the not-so-distant future. It is crucial to characterize the material's mechanical properties in ways to address such vulnerability. Nanoindentation is a widely used technique for measuring the mechanical properties of thin films that involves indenting the film with a small diamond tip and measuring the force-displacement response to calculate the film's elastic modulus, hardness, and other mechanical properties. For the first time, the nanoindentation analysis was performed on multiple vapor-diffused Nb3Sn samples coated at Jefferson Lab and Fermilab Nb3Sn coating facilities. This contribution will discuss the first results obtained from the nanoindentation of Nb3Sn-coated Nb samples prepared via the Sn vapor diffusion technique.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

First Results From Nanoindentation of Vapor Diffused Nb3Sn Films on Nb

The mechanical vulnerability of the Nb3Sn-coated cavities is identified as one of the significant technical hurdles toward deploying them in practical accelerator applications in the not-so-distant future. It is crucial to characterize the material's mechanical properties in ways to address such vulnerability. Nanoindentation is a widely used technique for measuring the mechanical properties of thin films that involves indenting the film with a small diamond tip and measuring the force-displacement response to calculate the film's elastic modulus, hardness, and other mechanical properties. The nanoindentation analysis was performed on multiple vapor-diffused Nb3Sn samples coated at Jefferson Lab and Fermilab coating facilities for the first time. This contribution will discuss the first results obtained from the nanoindentation of Nb3Sn-coated Nb samples prepared via the Sn vapor diffusion technique.

43 PARTICLE ACCELERATORS↗

Current status of research and development program for characterizing fuel debris at Fukushima Daiichi NPS by JAEA

Japan Government and TEPCO submitted a research road map for decommissioning Fukushima Daiichi Nuclear Power Plant. Two projects about debris are in progress: 'Assessment of simulated fuel debris characteristics' and 'Development of technologies for the processing of fuel debris'. The major results concerning the first project are the following 4 points. First, it was suggested that typical phase of oxide of fuel debris is (U,Zr)O{sub 2} and that of metal is Fe{sub 2}(Zr,U) by thermodynamic calculation. Secondly, important properties of fuel debris for developing defueling tools were identified as shape, size, density, hardness, elastic modulus, fracture toughness, thermal conductivity, specific heat (heat capacity), and melting point. Thirdly, the influence of seawater salt and B{sub 4}C/SUS to characteristics of debris was found, such as deposition of magnesium oxide crystal on the surface of fuel debris. The Influence of Pu to thermal properties of fuel debris was found, such as the increase of melting point. Concerning the second project, the major results are the following. First, a draft of the whole image of scenarios was developed. Secondly, the alkaline resolution method using Na{sub 2}O{sub 2} is most likely to be applied as a part of analysis technologies. Thirdly, it was shown that a part of fuel debris rich in U might be soluble in nitric acid. Fourthly, it was shown that all pyrochemical processes examined have potential to be applied for treating fuel debris. The results of the projects will contribute to the decommissioning program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Crush Strengths of Stainless Steel Honeycomb for Packaging

Honeycomb structures are used as energy absorbers to dissipate kinetic energy. Their low density to high axial strength and inexpensive cost make them ideal for the energy absorption application. Mechanical properties of lightweight materials are well known compared to more dense materials like stainless steel. Determines the viability of using 304 Stainless Steel honeycomb in future SRNL radioactive material packages. Using a combination of the material properties and testing procedures both static and dynamic crush strength of stainless steel honeycomb will be determined. Both static and dynamic crush strengths of stainless steel honeycomb need to be quantified because strain rate plays a role in the material strength. The stainless steel honeycomb being tested will be cut into sections of about 2.0 inches in width, 2.3 inches in length and 2.5 inches in height. The cell size of the material is 0.25 in and the ribbon thickness 0.003 in. The material has a yield strength of 48 ksi and an ultimate strength of 103.2 ksi, with an elastic modulus of 29,300 ksi. Compression testing to determine the static crush strength will use an Instron compression test machine. This Instron machine uses a 20 ksi capacity load cell, while recording data at varying low strain rates. Dynamic impact testing will involve dropping a 43.8 lb impactor from a height around 5 feet onto the stainless steel honeycomb. The honeycomb structure will be on a rigid surface and the impactor will be dropped via a quick release hook. Dynamic crush strength is determined from the weight of the impactor, height of the drop and difference in height of the honeycomb after the drop.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗