Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

Domain wall motion across microstructural features in polycrystalline ferroelectric films

This paper describes the effect of microstructural features such as grain boundaries and triple points on the pinning of domain wall motion in perovskite Pb(Zr 0.52 Ti 0.48 )O 3 (PZT) films on polycrystalline SrRuO 3 /SrTiO 3 substrates. Here, spatial variability in the collective domain wall dynamics was assessed using non-linearity mapping via Band Excitation Piezoresponse Force Microscopy (BE-PFM). Collocating the non-linearity maps with triple point locations (as visualized by EBSD) allowed for exploration of the effects that local microstructure (e.g., grain boundary) have on domain wall motion. It was found that the extrinsic behavior varied with both the misorientation angle and the proximity to the grain boundary. The width of influence of individual grain boundaries on the motion of domain walls was a function of the character of the grain boundary; random grain boundaries exhibit deeper minima in α d /d 33,initial and larger widths of influence (up to 905 nm) compared to coincident site lattice (CSL) boundaries (up to 572 nm). Additionally, triple points containing larger numbers of random boundaries exhibited non-Rayleigh behavior to greater distances, suggesting that the triple point provides either a deep potential minimum or a region where domain wall motion is unfavorable.

36 MATERIALS SCIENCE↗

Microstructural modification of additively manufactured metals by electropulsing

Additive manufacturing (AM) promises rapid development cycles and fabrication of ready-to-use, geometrically-complex parts. The metallic parts produced by AM often contain highly non-equilibrium microstructures, e.g. chemical microsegregation and residual dislocation networks. While such microstructures can enhance some material properties, they are often undesirable. Many AM parts are thus heat-treated after fabrication, a process that significantly slows production. This study investigated if electropulsing, the process of sending high-current-density electrical pulses through a metallic part, could be used to modify the microstructures of AM 316 L stainless steel (SS) and AlSi10Mg parts fabricated by selective laser melting (SLM) more rapidly than thermal annealing. Electropulsing has shown promise as a rapid postprocessing method for materials fabricated using conventional methods, e.g. casting and rolling, but has never been applied to AM materials. For both the materials used in this study, as-fabricated SLM parts contained significant chemical heterogeneity, either chemical microsegregation (316 L SS) or a cellular interdendritic phase (AlSi10Mg). In both cases, annealing times on the order of hours at high homologous temperatures are necessary for homogenization. Using electropulsing, chemical microsegregation was eliminated in 316 L SS samples after 10, 16 ms electrical pulses. In AlSi10Mg parts, electropulsing produced spheroidized Si-rich particles after as few as 15, 16 ms electrical pulses with a corresponding increase in ductility. Finally, this study demonstrated that electropulsing can be used to modify the microstructures of AM metals.

36 MATERIALS SCIENCE↗

On the efficacy of post-build thermomechanical treatments to improve properties of Zirconium fabricated using ultrasonic additive manufacturing

Here, hot-isostatic pressing has been applied to Zirconium plate fabricated using the ultrasonic additive manufacturing (UAM) technique to enhance interfacial bond quality. Specimens heated to 800 C for 1 h at 100 MPa pressure showed grain growth across many prior foil-to-foil interfaces, thereby increasing foil adhesion. In addition to the material softening induced by a loss of Hall-Petch strengthening, premature failure of specimens loaded parallel to the build direction was observed. Premature specimen failure was attributed to the local delamination at prior foil-to-foil boundaries where grain growth was pinned by Ti impurities introduced during the UAM process via the interaction between a Ti-alloy buffer foil and the welded Zr-foils underneath. In addition, the presence of Ti along select foil interfaces resulted in the nucleation and growth of secondary (Zr,Ti)(Fe,Cr) laves phases during higher-temperature thermomechanical processing. Using a combination of micro-scale X-ray computed tomography, fractography, and in-situ digital image correlation, the effect of defects along prior foil-to-foil boundaries was revealed as delamination-assisted plasticity accelerated specimen failure in preferred tensile orientations. These findings underscore the importance of impurity control when optimizing weld quality of higher-strength material systems using ultrasonic welding.

36 MATERIALS SCIENCE↗

Microstructural evaluation of a Fe-12Cr nanostructured ferritic alloy designed for impurity sequestration

Fast reactor fuel cladding candidate materials require proficiency in extreme environments consisting of high temperatures and irradiation doses in excess of 150 displacements per atom (dpa). Nanostructured oxide dispersion strengthened (ODS) alloys have been developed extensively for this purpose due to their notable high temperature strength, creep resistance, and irradiation resistance. However, their properties can deteriorate if interstitial impurities such as C and N are not well controlled during the fabrication process. A new Fe-12Cr nanostructured ODS alloy OFRAC (Oak Ridge Fast Reactor Advanced Fuel Cladding) with solute additions of Mo, Ti, and Nb has been developed to provide the desired properties mentioned above while simultaneously sequestering impurities within the matrix. After extrusion at 850°C, the as-extruded microstructure consists of an average 490 nm grain size and a high number density (6.8 × 10 23 m -3 ) of 2.2 nm diameter (Y,Ti,O) nanoclusters distributed homogeneously in the matrix. Atom probe tomography investigations suggest non-stochiometric compositions for the smallest nanoclusters. In addition, a second population of nanometer scale (Nb,Ti) rich carbonitrides is also present in the microstructure that captures the potentially detrimental C and N impurity atoms present in the matrix. Atom probe tomography results indicate elemental segregation of Cr, Mo, and Nb to grain boundaries in the as-extruded material, consistent with previous investigations of solid solution strengthening by solute additions. In conclusion, the ability of OFRAC to sequester impurities introduced from the powder metallurgical approach to nanostructured ferritic alloy development, compounded with its beneficial mechanical properties, makes this alloy a competitive candidate for fast reactor applications.

36 MATERIALS SCIENCE↗

Characterization of fluidized bed chemical vapor deposition ZrC coatings on PyC/YSZ kernels deposited under differing conditions

In this study, coated fuel particle architectures with ZrC coatings are candidate fuels for advanced power reactors and space nuclear propulsion (SNP) concepts. Owing to its relevance to SNP, the composition, microstructure, and mechanical properties of eight ZrC coatings prepared by fluidized bed chemical vapor deposition were evaluated. Evaluation by SEM and EBSD showed that all grains were columnar. Across the various examined samples, minor axis diameters varied between 0.3 and 1.1 μm, and major axis diameters varied between 0.4 and 2.3 μm. Major and minor diameters increased with thickness particularly at higher deposition temperatures in which the major grain axis (from an ellipse fit to the grain shape) increased by 2.5 μm over the entire coating. Coatings with higher reactive gas flows and Zr/C concentrations closer to 1 were observed to contain nanocrystalline graphite deposits. Reactive gas flow doubling led to increases in coating thickness from around 10–15 μm to around 22–27 μm.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methods development towards automated, physics-informed, quantitative quality control of TRISO-SiC

Tristructural-isotropic (TRISO) fuel particles have been developed as a high-performance fuel for use in high-temperature gas-cooled reactor (HTGR) systems due to their high efficiency and stability under both normal and off-normal conditions. Broader deployment of this technology in advanced nuclear applications may benefit from quantitative quality assurance and quality control (QA/QC) methods that directly link TRISO properties to downstream performance. A key TRISO property is the SiC layer microstructure, which influences fission product retention during irradiation. However, existing QA/QC for the TRISO-SiC microstructure comprises only a qualitative visual inspection; therefore, there is a clear opportunity for the development of quantitative methods for TRISO QA/QC. Here, to this end, previous work has demonstrated an image processing approach to grain boundary (GB) identification and subsequent extraction of microstructural metrics; however, extensive twinning within the SiC layer complicates such analyses because twin GBs significantly influence microstructural metrics but are not expected to contribute to fission product transport. This study presents the initial development, training, and testing of an ML-based image segmentation algorithm designed to identify and remove twin GBs from standard backscattered electron micrographs, providing an industrially applicable, quantitative, and physically meaningful QA/QC approach for the TRISO-SiC microstructure. Although pixel-wise performance metrics for the twin predictions are low, the change in grain area and the number of GB pixels after twin removal predicted by the ML workflow are within 1% of the true values calculated using crystallographic data. This suggests that the model is well capable of predicting overall twin boundary structures and grain morphology, and continued advancement of this approach could enable automated, scalable, and physics-informed QA/QC for TRISO-SiC microstructures, supporting the reliable qualification of coated particle fuels for next-generation reactor systems.

Computer vision↗

Fast in-situ annealing stage coupled with EBSD: A suitable tool to observe quick recrystallization mechanisms

A heating stage has been developed to perform in-situ annealing in a SEM equipped with an EBSD system in order to study recrystallization mechanisms. High temperature treatments could then be performed inside the SEM, up to 1180 Degree-Sign C and with high heating and cooling rates ({approx} 100 Degree-Sign C s{sup -1}). Samples were cooled down to room temperature to perform EBSD orientation mapping in between successive short-duration heat treatments. Microstructure evolution snapshots obtained this way allow gaining an insight into recrystallization mechanisms. The interest of such experiments is shown for two examples: static recrystallization of cold deformed pure tantalum and post-dynamic evolution of hot-deformed Zircaloy4. - Highlights: Black-Right-Pointing-Pointer Heating stage for in-SEM annealing at high temperature (up to 1200 Degree-Sign C). Black-Right-Pointing-Pointer High heating and cooling rates (100 Degree-Sign C s{sup -1}), no temperature overshoot. Black-Right-Pointing-Pointer Sequential observation of very fast recrystallization mechanisms.

36 MATERIALS SCIENCE↗

Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by austenitic filler metal

The evolution of microstructure and texture across an as-welded dissimilar UNS S32750 super duplex/UNS S30403 austenitic stainless steel joint welded by UNS S30986 (AWS A5.9 ER309LMo) austenitic stainless steel filler metal using gas tungsten arc welding process was evaluated by optical micrography and EBSD techniques. Due to their fabrication through rolling process, both parent metals had texture components resulted from deformation and recrystallization. The weld metal showed the highest amount of residual strain and had large austenite grain colonies of similar orientations with little amounts of skeletal ferrite, both oriented preferentially in the < 001 > direction with cub-on-cube orientation relationship. While the super duplex stainless steel's heat affected zone contained higher ferrite than its parent metal, an excessive grain growth was observed at the austenitic stainless steel's counterpart. At both heat affected zones, austenite underwent some recrystallization and formed twin boundaries which led to an increase in the fraction of high angle boundaries as compared with the respective base metals. These regions showed the least amount of residual strain and highest amount of recrystallized austenite grains. Due to the static recrystallization, the fraction of low degree of fit (Σ) coincident site lattice boundaries, especially Σ3 boundaries, was increased in the austenitic stainless steel heat affected zone, while the formation of subgrains in the ferrite phase increased the content of < 5° low angle boundaries at that of the super duplex stainless steel. - Graphical abstract: Display Omitted - Highlights: • Extensive grain growth in the HAZ of austenitic stainless steel was observed. • Intensification of < 100 > orientated grains was observed adjacent to both fusion lines. • Annealing twins with Σ3 CSL boundaries were formed in the austenite of both HAZ. • Cub-on-cube OR was observed between austenite and ferrite in the weld metal. • Weld metal had the lowest texture intensity and ratio of low angle and CSL boundaries.

36 MATERIALS SCIENCE↗

Analysis of heterogeneities in strain and microstructure in aluminum alloy and magnesium processed by high-pressure torsion

Two distinct bulk light metals were opted to study the shear strain evolution and associated heterogeneities in texture/microstructure development during torsional straining by high pressure torsion (HPT): a face centered cubic Al alloy (A5086) and a hexagonal commercial purity Mg. Relatively thick disk samples - four times thicker than usually employed in HPT process - were processed to 180° and 270° rotations. With the help of X-ray tomography, the shear strain gradients were examined in the axial direction. The results showed strongly localized shear deformation in the middle plane of the disks in both materials. These gradients involved strong heterogeneities in texture, microstructure and associated hardness, in particular through the thickness direction at the periphery of the disk where the interplay between significant strain hardening and possible dynamic recrystallization could occur. - Highlights: •HPT processing was conducted on bulk specimens thicker than the usual thin-disks. •The Al alloy (A5086) and commercial purity magnesium samples were compared. •Distributions of strain and microhardness were evaluated in the radial and axial direction. •Plastic deformation is highly localized in the middle plane at outer edge in both materials. •Different DRX rates governed the differences in microstructure and hardening behavior.

36 MATERIALS SCIENCE↗

Microstructural control of FeCrAl alloys using Mo and Nb additions

The effects of Mo and Nb additions on the microstructure and mechanical properties of two FeCrAl alloys were studied in this paper. Fine and uniform recrystallized grain structures (~ 20–30 μm) were achieved in both alloys through suitable annealing after warm-rolling. The formation of Fe 2 Nb-type Laves phase precipitates in the Nb-containing FeCrAl alloy effectively stabilized the deformed and recrystallized microstructures. The Mo-containing FeCrAl alloy exhibited strong γ texture fiber after annealing at 650–900 °C, whereas the annealed Nb-containing FeCrAl alloy had much weaker texture. Finally, both strength and ductility decreased as the grain size increased in both alloys.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of extruded Mg-Gd-Y-Zn-Zr alloys filled with intragranular LPSO phases

Highlights: • Intragranular thin-platelet LPSO phases strongly restrict the DRX. • The low extrusion ratio fails to widely break the intragranular LPSO. • The large extrusion ratio results in the full DRX via the CDRX mechanism. • Finer DRX-ed grains and LPSO induce the higher yield strength and elongation. • The larger grain size causes an increase in the strain hardening rate. - Abstract: A comparison has been made on the dynamic recrystallization (DRX), texture, and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloys extruded with different ratios (ER, 36 and 7.1). Intragranular long-period stacking ordered (LPSO) phases strongly restrict the DRX by restraining the lattice rotation of α-Mg grains and hindering the migration of the boundaries of DRX-ed grains. Extrusion with ER of 36 can widely break the intragranular LPSO phases and create a fully DRX-ed microstructure with a relatively random texture, while the lower ER of 7.1 fails to break the LPSO and leads to a bimodal microstructure with a strong basal fiber texture. Finer DRX-ed grains and smaller LPSO phases account for the superior tensile yield strength and elongation of the ER36 alloy. However, the ultimate tensile strength of the ER7.1 alloy catches up because its larger grain size causes an increase in the strain hardening rate.

36 MATERIALS SCIENCE↗

EBSD characterization of boundary types after discontinuous precipitation in a grit-blasted nickel-based superalloy

Highlights: • During recrystallization, high-angle grain boundaries increased dramatically. • The reaction fronts are high-angle GBs, but are not always correspond to CSL type. • Σ3 twin boundaries have been confirmed to be positive on reducing residual stress. • No advancing reaction front corresponds to Σ3 twin boundary type. - Abstract: In the present work, direct and detailed insights with respect to the statistical information on boundary type of discontinuous precipitates and their advancing reaction fronts in a Re-containing single crystal superalloy DD6 have been obtained by EBSD. With the annealing time prolonging, the reaction fronts proceeded into the original matrix for gradual release of grit-blast induced stress. The average recrystallized grain diameter and the average depth of recrystallization were respective 0.83 μm and 3.98 μm for the specimen annealed at 1050 °C for 10 min, which, after 16 h, had grown to the average values of 3.22 μm and 31.17 μm. The reaction fronts of discontinuous precipitation have been confirmed to be high-angle grain boundaries, but do not always correspond to CSL type. Besides the role of strain energy dissipation for recrystallization, the formation of twin structure has no direct relationship with the proceeding of reaction fronts. The information of boundary type of discontinuous precipitation and its advancing reaction fronts would provide new insight into the cellular recrystallization behavior.

36 MATERIALS SCIENCE↗

Twining and dynamic recrystallization in austenitic Alloy 718 during friction welding

Highlights: • DDRX was the primary grain refinement mechanism in friction welding of Alloy 718. • Two models were developed to explain the twin formation mechanism. • Intragranular twins were caused by grain boundary growth incidents. • Intergranular twin boundaries were ascribed to boundary growth stagnation. - Abstract: Quantitative boundary misorientation analysis verified that discontinuous dynamic recrystallization (DDRX) was the primary grain refinement mechanism in friction welding of Alloy 718. Two models were developed to explain the formation mechanism of intragranular twins and intergranular twins, respectively. Intragranular twins were caused by grain boundary growth incidents. After twin initiation, the twin boundary migrated toward the plastic-deformed grain interior to reduce the stored energy. Additionally, intergranular twin boundaries were ascribed to boundary growth stagnation. When boundary growth stagnation occurred, twin boundaries could form and altered the orientation of the boundary migration front, so that boundary migration could progress, leaving a single twin boundary behind.

36 MATERIALS SCIENCE↗

Influence of velocity of pressing in RCS processed AA8090 Al-Li alloy

Highlights: • For the first time the Influence of RCS on the properties of AA 8090 has been studied by processing velocity. • It is found that the properties vary according to pressing velocity and number of passes. • Reported significant property improvement achieved through the pressing velocity of 1.5mm/s. - Abstract: The effect of the velocity of pressing on grain refinement in AA8090 Al-Li alloy sheets during repetitive corrugation and straightening (RCS) at 300 °C is studied. V-groove corrugation dies and flattening dies were used at three different pressing velocities of 1.5 mm/s, 2 mm/s and 2.5 mm/s. The specimen temperature was maintained at 300 °C. Grain refinement was significantly influenced by the pressing velocity. The samples processed for 8 passes at a pressing velocity of 1.5 mm/s had an improved microhardness value of 104 HV and an increased tensile strength of 405 MPa which is respectively 39% and 113% more than the corresponding values in the parent material. TEM analysis showed that samples processed at a pressing velocity of 1.5 mm/s had in places a grain size down to 50 nm and the EBSD results revealed that the average grain size was 2 μm, with 86% of the total number of grain boundaries of the high angle type.

36 MATERIALS SCIENCE↗

A comparative research on bobbin tool and conventional friction stir welding of Al-Mg-Si alloy plates

Highlights: • 6061-T4 Al plates were successfully welded by both BT-FSW and C-FSW processes. • A wide welding parameter window was achieved with bobbin tool. • BT-FSW joints showed good strength similar to that of C-FSW joints. • Proving that an Isothermal Dissolution Layer Theory also apply to BT-FSW - Abstract: In our work, Al-Mg-Si (6061Al -T4) plates of 6 mm thickness were subjected to bobbin tool friction stir welding (BT-FSW) and conventional friction stir welding (C-FSW) for comparison. How the welding process affects the microstructure and mechanical properties was investigated at various rotation rates and welding speeds. The results showed that butt FSW joints with high quality could be produced at the selected parameters. The joint strength rose with enhanced welding speed and was nearly independent of the rotation rate in both the welding processes. The strength of the joints produced with BT-FSW reached the same level as that of the C-FSW. The maximum joint strength of 229 MPa was 93% of the base material (BM), which is superior to the reported results of 60–80% for the T4 condition. The fracture position of most of the joints was in the heat-affected zone (HAZ), which is the lowest hardness zone.

36 MATERIALS SCIENCE↗

Formation mechanism of an α2 phase-rich layer on the surface of Ti-22Al-25Nb alloy

Highlights: • This paper reports the formation mechanism of a α{sub 2}-rich layer on the surface of the Ti-22Al-25Nb alloy. • The α{sub 2}-rich layer is significantly harder than the alloy interior. • The α{sub 2}-rich layer is formed owing to the Ti{sub 2}O{sub 3} particles produced by oxygen infiltration at the surface. • The relative orientation of the α{sub 2} and Ti{sub 2}O{sub 3} phases is (1–100)α{sub 2}//(1–100)Ti{sub 2}O{sub 3}. - Abstract: In order to investigate the formation mechanism of the α{sub 2}-rich layer in the surface of the Ti-22Al-25Nb alloy, systematic analyses are carried out on the surface of the alloy by using SEM, XRD and EBSD. The results reveal that this α{sub 2}-rich layer is formed by oxidation of the surface layer. In this surface oxidation layer, there are abundant Ti{sub 2}O{sub 3} particles similar with the α{sub 2} phase in structure. These Ti{sub 2}O{sub 3} particles serve as nucleation points and lower the nucleation energy of the α{sub 2} phase, promoting the precipitation and growth of α{sub 2} phase on the surface layer of the alloy. This surface layer has a hardness of 684 HV, significantly exceeding the value of 312 HV for the interior of the alloy and thus considerably improves the surface properties of the alloy, serving as a high-performance, self-generated surface strengthening layer.

36 MATERIALS SCIENCE↗

Impact of forging direction on the recrystallization behaviour of nickel base superalloy AD730 billet material at subsolvus temperatures

Highlights: • Large unrecrystallized grains present a fine distribution of intragranular γ′ precipitates; • Intragranular precipitates play a key role on strain distribution and subsequent recrystallization behaviour for AD730; • Continuous dynamic recrystallization (CDRX) promotes the gradual consumption of large unrecrystallized grains. • Undissolved secondary precipitates play a key role on the microstructural evolution of AD730 • No significant effect associated to the forging direction on the recrystallization behaviour of AD730 was found. AD730™ is a newly developed Ni-based superalloy for turbine disk applications produced by cast and wrought processes. Conventional ingot-to-billet conversion is an expensive and very complex operation. Because of the difficulties to achieve a uniform strain for recrystallization, large unrecrystallized grains are retained along this process. Heterogeneities of grain size have a negative impact on subsequent forging processes as well as ultrasonic inspectability of the destination part. The main aim of this work is to analyse the impact of both forging direction (billet, cogging) and strain (ε = 0.3–2) on the microstructural evolution of AD730 at subsolvus temperatures from a semi-finished product (billet) under conditions representative of both cogging and hot forging operations. Special attention to the presence of large unrecrystallized grains was paid. Double truncated cones (DTCs) were hot forged at subsolvus temperatures followed by air cooling. SEM and EBSD analysis were conducted in the as-received (billet) and the as-forged conditions. AD730 alloy presents a complex microstructure characterized by the presence of large unrecrystallized grains, aligned in the billet direction, with remarkable differences in γ′ precipitates distribution as compared to recrystallized structures. The fine distribution of primary γ′ precipitates (pinning effect) plays a key role on grain size control but also on the recrystallization behaviour. Continuous dynamic recrystallization (CDRX) mechanism was found to be operating in the large unrecrystallized grains, promoting the formation intragranular DRX grains and the gradual recrystallization of these grains. Strain presents a strong effect on the microstructural evolution of AD730, increasing the recrystallization fraction and refining the structure. By contrast, no significant effect associated to the forging direction was found. Conditions representative of cogging operations (ε ≤ 0.6) at subsolvus temperatures were translated into large fractions of unrecrystallized structures (strain accumulation).

36 MATERIALS SCIENCE↗

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗