Search NASA⌕ Search

SEARCH · Search NASA

Results for “laser absorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Nd:Glass-Raman laser for water vapor dial

A tunable solid-state Raman shifted laser which was used in a water vapor Differential Absorption Lidar (DIAL) system at 9400 A is described. The DIAL transmitter is based on a tunable glass laser operating at 1.06 microns, a hydrogen Raman cell to shift the radiation to 1.88 microns, and a frequency doubling crystal. The results of measurements which characterize the output of the laser with respect to optimization of optical configuration and of Raman parameters were reported. The DIAL system was also described and preliminary atmospheric returns shown.

Kagann, R. H.↗
NASA NTRS1987

Kinetics of the reactions of SH radicals with NO2 and O2

The SH + NO2 reaction rate constant was measured by monitoring SH concentrations with long-path optical absorption at 324 nm in a laser photolysis system. At 298 K, the rate constant was found to be (4.8 + or - 1.0) x 10 to the -11th cu cm/molecule per sec. An upper limit of 4 x 10 to the -19th cu cm/molecule per sec was inferred for the SH + O2 reaction, indicating that the atmospheric oxidation of the SH radical may occur via reaction with species such as NO2 and O3.

Stachnik, R. A.↗
NASA NTRS1988

Lidar atmospheric sounder and altimetry for the Earth Observing System (EOS) satellite

The NASA Space Station Program includes development of a polar orbiting platform as part of the Earth Observing System (EOS) Program. A lidar facility is in turn being developed for the EOS polar platforms to make atmospheric science measurements utilizing techniques of laser atmospheric backscatter (optical radar), Differential Absorption Lidar (DIAL) and altimetry. The science for this facility has been developed by the Lidar Atmospheric Sounder and Altimetry (LASA) panel for the Earth Observing System and will be addressed in an Announcement of Opportunity which will be released early in 1988 to solicit science proposals and experiment proposals for the EOS missions.

Woerner, Charles V.↗
NASA NTRS1989

Stratospheric ozone measurements using a ground-based, high-power lidar

A lidar facility has been established at the JPL-Table Mountain Observatory at an altitude of 2300 m in the San Gabriel Mountains northeast of Los Angeles. This facility uses the laser remote sensing technique of differential absorption lidar (DIAL) to derive atmospheric ozone concentration profiles. Two separate systems are used to obtain the ozone profile: an Nd:YAG based troposphere system will measure from the ground to 20 km and an excimer based system measures from 15 km to 50 km. The systems are designed to make long-term measurements so that small changes in the ozone abundance can be detected. This paper will describe the stratospheric ozone lidar system and present some of the results which have been obtained since it began routine operation in January 1988.

Mcdermid, I. Stuart↗
NASA NTRS1992

Nonintrusive spectroscopic techniques for supersonic/hypersonic aerodynamics and combustion diagnostics

This paper presents an overview of the primary nonintrusive diagnostic techniques being developed by the NASA Langley Research Center to address the validation needs of Computational Fluid Dynamic (CFD) codes. The techniques include absorption in the UV and IR, Laser Induced Fluorescence, electron beam fluorescence, and a number of scattering techniques including Rayleigh, spontaneous Raman, and several coherent Raman spectroscopies. Most of the techniques are highly specialized, require complex data interpretation, and can satisfy only a few of the CFD needs. For these reasons, the evolving trend in flowfield diagnostics appears to favor a mode in which the diagnostic researcher, the experimental aerodynamicist, and the CFD community jointly define experiments based on the aeronautical requirements and on available diagnostic techniques.

Exton, R. J.↗
NASA NTRS1991

Concentration measurements in an axisymmetric jet using laser-induced fluorescence

Errors associated with the use of an image processing technique to correct images of an axisymmetric jet produced by laser-induced fluorescence are analyzed. In particular, attention is given to errors related to the alignment of the optical system, spreading of the laser light sheet, laser light attenuation due to light absorption by the fluorescent dye, and solubility effects. Although the above effects are negligible in the case of a small low-concentration jet, they are not negligible in all fluorescent dye experiments.

Shoe, B.↗
NASA NTRS1997

Kinetics of the BrO + NO2 Association Reaction. Temperature and Pressure Dependence in the Falloff Regime

A laser flash photolysis-long path absorption technique has been employed to study the kinetics of the reaction BrO + NO2 + M yields (k1) products as a function of temperature (248-346 K), pressure (16-800 torr), and buffer gas identity (N2,CF4) The reaction is found to be in the falloff regime between third and second-order over the entire range of conditions investigated This is the first study where temperature-dependent measurements of k1(P,T) have been reported at pressures greater than 12 torr; hence, our results help constrain choices of k1(P,T) for use in models of lower stratospheric BrO(x) chemistry. Approximate falloff parameters in a convenient form for atmospheric modeling are derived.

Thron, R. P.↗
NASA NTRS1997

Kinetics of the Reactions of IO Radicals with NO and NO2

A laser flash photolysis-long path absorption technique has been employed to study the kinetics of the reactions of IO radicals with NO and NO2 as a function of temperature and pressure. The IO and NO rate coefficient is independent of pressure over the range 40-200 Torr of N2, and its temperature dependence over the range 242-359 K is adequately described by the Arrhenius expression k(sub 1) = (6.9 +/- 1.7) x 10(exp -12) exp[(328 +/- 71)/T] cu cm/(molecule.s) (errors are 2 sigma, precision only). These Arrhenius parameters are similar to those determined previously for the ClO + NO and BrO + NO reactions. The IO and NO2 association reaction is found to be in the falloff regime over the temperature and pressure ranges investigated (254-354 K and 40-750 Torr of N2). Assuming F(sub c) = 0.4 independent of temperature, a physically reasonable set of falloff parameters which adequately describe the data are k(sub 0) = 7.7 x 10(exp -31)(T/300)(exp -5.0) cm(exp 6)/(molecule(exp 2).s) and k(sub infinity) = 1.55 x 10(exp -11)cu cm/(molecule.s) independent of temperature. The IO + NO2 rate coefficients determined in this study are about a factor of 2 faster than those reported in the only previous study of this reaction.

Daykin, E. P.↗
NASA NTRS2010

Development of a Coherent Differential Absorption Lidar for Range Resolved Atmospheric CO2 Measurements

A pulsed, 2-m coherent Differential Absorption Lidar (DIAL) / Integrated Path Differential Absorption (IPDA) transceiver, developed under the Laser Risk Reduction Program (LRRP) at NASA, is integrated into a fully functional lidar instrument. This instrument will measure atmospheric CO2 profiles (by DIAL) initially from a ground platform, and then be prepared for aircraft installation to measure the atmospheric CO2 column densities in the atmospheric boundary layer (ABL) and lower troposphere. The airborne prototype CO2 lidar can measure atmospheric CO2 column density in a range bin of 1km with better than 1.5% precision at horizontal resolution of less than 50km. It can provide the image of the pooling of CO2 in lowlying areas and performs nighttime mass balance measurements at landscape scale. This sensor is unique in its capability to study the vertical ABL-free troposphere exchange of CO2 directly. It will allow the investigators to pursue subsequent in science-driven deployments, and provides a unique tool for Active Sensing of CO2 Emissions over Night, Days, and Seasons (ASCENDS) validation that was strongly advocated in the recent ASCENDS Workshop.

Yu, Jirong↗
NASA NTRS2011

Range Resolved CO2 Atmospheric Backscattering Measurements Using Fiber Lasers and RZPN Code Modulation

We report the use of a return-to- zero (RZPN) pseudo noise modulation technique for making range resolved measurements of CO2 within the planetary boundary layer (PBL) using commercial, off-the-shelf, components. Conventional, range resolved, DIAL measurements require laser pulse widths that are significantly shorter than the desired spatial resolution and necessitate using pulses whose temporal spacing is such that scattered returns from only a single pulse are observed by the receiver at any one time (for the PBL pulse separations must be greater than approximately 20 microseconds). This imposes significant operational limitations when using currently available fiber lasers because of the resulting low duty cycle (less than approximately 0.0005) and consequent low average laser output power. The RZPN modulation technique enables a fiber laser to operate at much higher duty cycles (approaching 0.04) thereby more effectively utilizing the amplifier's output. This increases the counts received by approximately two orders of magnitude. Our approach involves employing two distributed feedback lasers (DFB), each modulated by a different RPZN code, whose outputs are then amplified by a CW fiber amplifier. One laser is tuned to a CO2 absorption line; the other operates offline thereby permitting the simultaneous acquisition of both on and offline signals using independent RZPN codes. This minimizes the impact of atmospheric turbulence on the measurement. The on and offline signals are retrieved by deconvolving the return signal using the appropriate kernels.

Burris, John↗
NASA NTRS2012

Characterization of Material Response During Arc-Jet Testing with Optical Methods Status and Perspectives

The characterization of ablation and recession of heat shield materials during arc jet testing is an important step towards understanding the governing processes during these tests and therefore for a successful extrapolation of ground test data to flight. The behavior of ablative heat shield materials in a ground-based arc jet facility is usually monitored through measurement of temperature distributions (across the surface and in-depth), and through measurement of the final surface recession. These measurements are then used to calibrate/validate materials thermal response codes, which have mathematical models with reasonably good fidelity to the physics and chemistry of ablation, and codes thus calibrated are used for predicting material behavior in flight environments. However, these thermal measurements only indirectly characterize the pyrolysis processes within an ablative material pyrolysis is the main effect during ablation. Quantification of pyrolysis chemistry would therefore provide more definitive and useful data for validation of the material response codes. Information of the chemical products of ablation, to various levels of detail, can be obtained using optical methods. Suitable optical methods to measure the shape and composition of these layers (with emphasis on the blowing layer) during arc jet testing are: 1) optical emission spectroscopy (OES) 2) filtered imaging 3) laser induced fluorescence (LIF) and 4) absorption spectroscopy. Several attempts have been made to optically measure the material response of ablative materials during arc-jet testing. Most recently, NH and OH have been identified in the boundary layer of a PICA ablator. These species are suitable candidates for a detection through PLIF which would enable a spatially-resolved characterization of the blowing layer in terms of both its shape and composition. The recent emission spectroscopy data will be presented and future experiments for a qualitative and quantitative characterization of the material response of ablative materials during arc-jet testing will be discussed.

Winter, Michael↗
NASA NTRS2010

Low Power Consumption Lasers for Next Generation Miniature Optical Spectrometers for Major Constituent and Trace Gas Analysis

The air quality of any manned spacecraft needs to be continuously monitored in order to safeguard the health of the crew. Air quality monitoring grows in importance as mission duration increases. Due to the small size, low power draw, and performance reliability, semiconductor laser-based instruments are viable candidates for this purpose. The minimum instrument size requires lasers with emission wavelength coinciding with the absorption of the fundamental frequency of the target gases which are mostly in the 3.0-5.0 micrometers wavelength range. In this paper we report on our progress developing high wall plug efficiency type-I quantum-well GaSb-based diode lasers operating at room temperatures in the spectral region near 3.0-3.5 micrometers and quantum cascade (QC) lasers in the 4.0-5.0 micrometers range. These lasers will enable the development of miniature, low-power laser spectrometers for environmental monitoring of the spacecraft.

semiconductor lasers↗
NASA NTRSDate not supplied

Relative Detectability of Iron-Bearing Phases for the Mars 2020 Sherloc Deep UV Raman Instrument: 1. Focusing on Carbonates

A deep ultraviolet (DUV) Raman and fluorescence instrument is a surface standoff instrument mounted on the robotic arm of the Mars 2020 (M2020) rover Perseverance, and it is a key element of the Scanning Habitable Environments with Luminescence for Organics and Chemicals (SHERLOC) investigation [1]. Measurement and science objectives include mineralogical and organic images (~100 μm/pixel) that map sub-millimeter spatial distributions and characterization of primary and secondary minerals, potential organics, and their interaction/alteration products. The results of data analysis pertain to understanding igneous and alteration processes on Mars through time, assessing habitability, evidencing in situ biosignatures, and, along with results from other Perseverance instruments, selecting samples to cache for Mars sample return. Acceptance of the SHERLOC investigation for the NASA M2020 mission [2] created a need for Mars-relevant DUV Raman spectra, particularly for inorganic materials [e.g., 3, 4]. As reported previously [e.g., 4, 5], phases with Fe cations as essential elements (e.g., siderite (FeCO3) and ankerite (FeCa(CO3)2) for carbonates) significantly hinder detection by DUV Raman because of intense absorption of incident and scattered DUV laser radiation by Fe cations. We report here the relative detectability of carbonates (Mg,Ca,Fe,Mn)CO3 by DUV Raman using a SHERLOC analog laboratory instrument.

R V Morris↗
DOE OSTI2023

Inverse Bremsstrahlung Absorption

Inverse bremsstrahlung absorption was measured based on transmission through a finite-length plasma that was thoroughly characterized using spatially resolved Thomson scattering. Expected absorption was then calculated using the diagnosed plasma conditions while varying the absorption model components. To match data, it is necessary to account for: (1) the Langdon effect; (2) laser-frequency (rather than plasma-frequency) dependence in the Coulomb logarithm, as is typical of bremsstrahlung theories but not transport theories; and (3) a correction due to ion screening. Radiation-hydrodynamic simulations of inertial confinement fusion implosions have to date used a Coulomb logarithm from the transport literature and no screening correction. Here, we anticipate that updating the model for collisional absorption will substantially revise our understanding of laser-target coupling for such implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1986

Observation of atmospheric ozone by dial with Raman lasers pumped by a KrF laser

Since the XeCl excimer laser (308 nm) was first used in Differential Absorption Lidar (DIAL) for stratospheric ozone detection, the XeCl ozone lidar became a useful tool for the monitoring of the stratospheric ozone concentration. Shorter wavelength lasers are needed for the observation of ozone in the troposphere where the ozone concentration is about one order of magnitude smaller than in the stratosphere. In 1983, tropospheric ozone was observed with the combination of the second Stokes line (290.4 nm) of stimulated Raman scattering from methane pumped by a KrF laser and the XeCl laser line. The measurement of the ozone distribution from ground to 30 km was reported, using three Stokes lines of Raman lasers pumped by a KrF laser. At wavelengths shorter than 295 nm, the background solar radiation is effectively suppressed by atmospheric ozone. Such a solar-blind effect can be expected when two wavelengths 277 and 290.4 nm are used for DIAL ozone detection. A preliminary measurement of the day time ozone distribution in the troposphere is presented using these wavelengths generated by a KrF laser with a Raman shifter. Analysis using the lidar equation predicts the maximum detectable range is 7 km.

Maeda, M.↗