Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural organization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mechanical Characterization of Low Modulus Polymer-Modified Calcium-Silicate-Hydrate (C-S-H) Binder

Calcium-silicate-hydrate (C-S-H) represents a key microstructural phase that governs the mechanical properties of concrete at a large scale. Defects in the C-S-H phase are also responsible for the poor ductility and low tensile strength of concrete. Manipulating the microstructure of C-S-H can lead to new cementitious materials with improved structural performance. This paper presents an experimental investigation aiming to characterize a new synthetic polymer-modified synthetic calcium-silicate-hydrate (C-S-H)/styrene-butadiene rubber (SBR) binder. The new C-S-H/SBR binder is produced by calcining calcium carbonate and mixing this with fumed silica (SiO 2 ), deionized water and SBR. Mechanical, physical, chemical and microstructural characterization was conducted to measure the properties of new hardened C-S-H binder. Results from the experimental investigation demonstrate the ability to engineer a new C-S-H binder with low elastic modulus and improved toughness and bond strength by controlling the SBR content and method of C-S-H synthesis. The new binder suggests the possible development of a new family of low-modulus silica-polymer binders that might fit many engineering applications such as cementing oil and gas wells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Solvent Processing and Ionic Liquid-Enabled Long-Range Vertical Ordering in Block Copolymer Films with Enhanced Film Stability

Rapid and reliable processing methods for forming ordered block copolymer (BCP) materials with low defect density in a thin film geometry are required for many nanotechnology applications. Vertically aligned BCP structures, in particular, have applications ranging from nanolithography for electronics and photonics to nanoporous membranes for water remediation and novel batteries for flexible electronics. However, the attainment of nearly complete vertical orientational order of the BCP ordered phase remains challenging. Solvent-based techniques, such as direct immersion annealing (DIA) and solvent vapor annealing (SVA), have immense potential for these applications of BCP films, as it allows for tuning of their thermodynamic, structural, and chain mobility driven kinetic properties. We first demonstrate that DIA, using a judicious choice of binary solvent mixtures along with a relatively hydrophobic ionic liquid (IL), induces the rapid vertical ordering in polystyrene-b-polymethylmethacrylate (PS-PMMA) block copolymer in lamellar films. The IL establishes synergy to the binary solvent mixture of toluene and heptane to 1 create a near-neutral solvent environment for attaining the vertical microstructure of the BCP. Next, we show that IL can suppress the de-wetting of the PS-PMMA films to achieve long-range order using SVA in cylindrical films for long annealing times. Both vertical and horizontal morphology is attained in these films by selecting different solvent environments. Furthermore, attaining enhanced vertical and horizontal BCP structure with long-range defect-free order by tuning solvent quality and using additives like IL can render them useful for many nanotech applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Direct Ab Initio Simulation of the Synthesis of BaZrO 3 and the Microstructure Impacts on Proton Transport

Controlling and predicting the processing-structure-performance relationship in functional materials is a grand challenge in materials science, with important implications for a wide range of emerging applications; a high fidelity understanding of the performance impact of microstructures formed under synthesis conditions is required to develop advanced materials, such as solid-state fuel cells and electrolyzers. Using the ceramic BaZrO 3 as a case study, we directly simulate the synthesis and investigate how proton transport is dictated by microstructures. We develop a framework that couples density functional theory (DFT), machine-learning interatomic potential (MLIP) driven molecular dynamics, and grand canonical Monte Carlo to perform large-scale, microstructure-resolved, atomistic simulations of proton transport in experimentally representative polycrystalline structures. Our fully ab initio approach, using a MLIP as a proxy for DFT, allows us to quantify the competition between two distinct diffusion mechanisms: one associated with grain-boundary regions and another within grains. When the impacts of grain boundaries are taken into account, proton transport exhibits substantial deviation from the bulk oxide limit. This addresses long-standing discrepancies between theory and experiments. Our integrated approach provides atomistic insight into microstructure-dependent proton pathways in BaZrO 3 and establishes a general protocol for predicting processing-structure-performance relationships.

organic↗
DOE OSTI2020

Understanding and Strategies for Controlled Interfacial Phenomena in Lithium-Ion Batteries and Beyond

Electrolyte chemistry and properties and electrode structure and chemical properties particularly at the interfaces are crucial for the development of advanced battery components. This project focused on elucidating the roles of the electrolyte and electrode on the formation and evolution of the SEI layer and cell electrochemical performance on silicon and on Li metal anodes. For Si nano/microstructures we evaluated lithiation, volume changes, reactivity, and chemo-mechanical transformations as functions of nanoparticle size, shape, presence of coatings, electrolyte composition, electron leakage to the electrolyte, and cycling. For Li metal anodes we provided detailed analyses of the electrode and electrolyte effects on interfacial reactivity and as a function of microstructural evolution and underlying stochasticity as dendrites nucleate and grow. We thoroughly investigated and simulated how the chemistry of the various components of the electrolyte and the electrode architecture may affect the electrochemical reactions as well as cell degradation. A multiscale modeling approach was utilized, where atomistic simulations informed about the microscopic behavior of the system, and intermediate time and length scales were investigated with mesoscopic models. Results were also tested against selected experiments from our collaborators. The combined theoretical-experimental strategy saves costs by utilizing predictions from computational analyses to guide experimentation.

25 ENERGY STORAGE↗
DOE OSTI2022

Layered oxide cathode-inspired secondary hard carbon microsphere anode material for high-power and long-life rechargeable batteries

A new anode material that will provide lithium ion (Li-ion) batteries with high energy and power density is urgently needed. In this work, a layered oxide cathode-inspired secondary hard carbon microsphere (CMS) anode material was designed, and exhibited excellent rate performance and long cyclability. Polyacrylonitrile/poly(styrene-co-acrylonitrile) (PAN/SAN) compositions displaying the meatball-like shape of the PAN precursor were carbonized into CMSs having turbostratic microstructures. The CMS carbonized at 1,000°C (CMS1000) displayed high specific capacity at the highest current density of 1,000mAg -1 , i.e., 77.6 % of its average charge capacity at 100 mA g -1 , and considerable cycling retention after 500 cycles, i.e., 83.8 % of the specific capacity at cycle 25. In conclusion, our work demonstrates that the design of new anode materials is a fruitful route to improve commercial Li-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Hotspot’s Better Half: Non-Equilibrium Intra-Molecular Strain in Shock Physics

Shockwave interactions with a material’s microstructure localizes energy into hotspots, which act as nucleation sites for complex processes such as phase transformations and chemical reactions. To date, hotspots have been described via their temperature fields. Nonreactive, all-atom molecular dynamics simulations of shock-induced pore collapse in a molecular crystal show that more energy is localized as potential energy (PE) than can be inferred from the temperature field and that PE localization persists beyond thermal diffusion. Furthermore, the origin of the PE hotspot is traced to large intramolecular strains, storing energy in modes readily available for chemical decomposition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Determination of Scale Bar for AGHCF Metallography Data

The DOE Nuclear Energy Advanced Reactor Technologies (ART) Fast Reactor Program (FRP) has supported the development of several databases containing information on the safety performance of fast reactors, components, and fuels. This growing collection of legacy experimental data, operating data, and analysis is available online to registered users. Metallography data represents one of the most critical types of post-irradiation examination (PIE) data being collected, organized, and archived in several ART Fast Reactor Databases (https://frdb.ne.anl.gov), including the Metallic Fuels Irradiation & Physics Database (FIPD), Out-of-Pile Transient Database (OPTD), and TREAT (the Transient Reactor Test Facility) Experimental Relational Database (TREXR). These databases contain three principal sets of metallography data. The first set comprises metallography data from Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) irradiated fuel pins examined in the Hot Fuel Examination Facility (HFEF). The second set consists of metallography data from EBR-II irradiated fuel pins examined in the Alpha-Gamma Hot Cell Facility (AGHCF). The third set includes metallography data from transient-tested fuel pins (including both out-of-pile furnace tests and TREAT tests) examined in AGHCF. Since both the second and third sets were generated in AGHCF, they are governed by identical specifications. The metallography data in the databases consist of digital images scanned from either positive or negative photographic films. To analyze the microstructure of a fuel pin, a series of preparatory steps are required, including sectioning, epoxy mounting, mechanical grinding and polishing, and etching. Following sample preparation, specimens are transferred for metallographic examination. The AGHCF and HFEF metallography data were generated using optical microscopes manufactured by Leitz and Bausch and Lomb (B&L). Images were recorded on Polaroid film at preset magnifications. Magnification verification for the Leitz and B&L metallographs was conducted every two months prior to 1989 and at least every six months from 1989 through the conclusion of the IFR program. Magnifications determined from imaging of microslide standards were compared to the instrument settings for magnifications ranging from 50× to 500×. If the magnifications determined from standards deviated from the instrument settings, adjustments were made to the bellows extension until agreement was achieved. The specifications for AGHCF and HFEF legacy metallography data have been established based on available hard-copy and digital records, most of which have been incorporated into the data repositories associated with FIPD, OPTD, and TREXR. Detailed specifications including hard-copy records, digitized records, cutting diagrams and sectioning schemes, high-magnification photographs, photomosaics (composites), information tags, scale bars, and magnification verification procedures can be found in a separate report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

A Novel Laser 3D Printing Method for the Advanced Manufacturing of Protonic Ceramics

Protonic ceramics (PCs) with high proton conductivity at intermediate temperatures (300–600 °C) have attracted many applications in energy conversion and storage devices such as PC fuel/electrolysis cells, PC membrane reactors, hydrogen pump, hydrogen or water-permeable membranes, and gas sensors. One of the essential steps for fulfilling the practical utilization of these intermediate-temperature PC energy devices is the successful development of advanced manufacturing methods for cost-effectively and rapidly fabricating them with high energy density and efficiency in a customized demand. In this work, we developed a new laser 3D printing (L3DP) technique by integrating digital microextrusion-based 3D printing and precise and rapid laser processing (sintering, drying, cutting, and polishing), which showed the capability of manufacturing PCs with desired complex geometries, crystal structures, and microstructures. The L3DP method allowed the fabrication of PC parts such as pellets, cylinders, cones, films, straight/lobed tubes with sealed endings, microchannel membranes, and half cells for assembling PC energy devices. The preliminary measurement of the L3DP electrolyte film showed a high proton conductivity of ≈7 × 10−3 S/cm. This L3DP technique not only demonstrated the potential to bring the PCs into practical use but also made it possible for the rapid direct digital manufacturing of ceramic-based devices.

08 HYDROGEN↗
DOE OSTI2023

Manufacturing porous U10Zr fuels with controlled porosities by SPS and thermal properties

To accommodate the swelling of metallic fuels induced by the fission gas release during burnup in sodium fast reactor for a sodium-free fuel option, advanced U-10Zr fuels with controlled porosity were designed and demonstrated by spark plasma sintering. U-10Zr fuel pellets with manufactured porosities varying from 35% up to fully dense fuel pellets have been fabricated by controlling ball milling times of the starting uranium powders, sintering temperature, pressure, and duration, and the correlation among the microstructure control – porosity – sintering conditions has been established. To further mimick the pore structure in irradiated fuels, different pore formers (NaCl and NH4HCO3) have been used to control the pore size and distribution. Microstructure characterization indicates a lamellar reaction zone of U and Zr, differing from the arc-melted U-10Zr as a result of rapid consolidation of SPS at lower temperature and short durations. The thermal conductivity of U10Zr with different porosities are also measured. Here this work demonstrates the success in manufacturing new metallic fuel forms with controlled porosities and pore distribution, which can be used as model systems to investigate the thermal transfer behavior of metallic fuels in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A novel sub-pilot-scale direct-contact ultrasonic dehydration technology for sustainable production of distillers dried grains (DDG)

DDG is a major source of protein, calcium, phosphorus, and sulfur is arguably the most important byproduct of the bioethanol industry with increasing demand over the past few years. Reducing energy consumption in the DDG production process and energy recovery from DDG is vital for sustainable bioethanol productions. In this paper, a novel direct-contact multi-frequency, multimode, and modulated (MMM) ultrasonic dryer (US) was developed for the first time and has been applied in dehydration of wet distillers' grain (WDG). Ultrasonic drying (US) was combined with a convective airflow (HA) at different temperatures of 25 (room temperature), 50 and 70 °C to evaluate the impact of US, HA, and US + HA on drying kinetics, activation energy, chemical compositions, microstructure, and color of DDG. Semi-empirical kinetic models were developed and evaluating drying performances showed that the application of ultrasound significantly enhanced the drying rate and decreased the drying time (by 46%), especially at low drying temperatures. The activation energy for moisture removal in the presence of ultrasound was about 50% of that without ultrasound. The final dried distillers' grains product processed by ultrasonic drying had a brighter color, a higher available protein, a higher digestible protein (the lowest acid detergent insoluble crude protein), and a better surface profile with no compromise on minerals and fiber contents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

3D-Printing of Meso-structurally Ordered Carbon Fiber/Polymer Composites with Unprecedented Orthotropic Physical Properties

Here we report the first example of a class of additively manufactured carbon fiber reinforced composite (AMCFRC) materials which have been achieved through the use of a latent thermal cured aromatic thermoset resin system, through an adaptation of direct ink writing (DIW) 3D-printing technology. We have developed a means of printing high performance thermoset carbon fiber composites, which allow the fiber component of a resin and carbon fiber fluid to be aligned in three dimensions via controlled micro-extrusion and subsequently cured into complex geometries. Characterization of our composite systems clearly show that we achieved a high order of fiber alignment within the composite microstructure, which in turn allows these materials to outperform equivalently filled randomly oriented carbon fiber and polymer composites. Moreover, our AM carbon fiber composite systems exhibit highly orthotropic mechanical and electrical responses as a direct result of the alignment of carbon fiber bundles in the microscale which we predict will ultimately lead to the design of truly tailorable carbon fiber/polymer hybrid materials having locally programmable complex electrical, thermal and mechanical response.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Chemical short-range order in derivative Cr–Ta–Ti–V–W high entropy alloys from the first-principles thermodynamic study

The development of high-entropy alloys (HEAs) focuses on exploring compositional regions in multi-component systems with all alloy elements in equal or near-equal atomic concentrations. Initially it was based on the main idea that high mixing configurational entropy contributions to the alloy free energy could promote the formation of a single solid solution phase. By using the ab-initio based Cluster Expansion (CE) Hamiltonian model constructed for the quinary bcc Cr–Ta–Ti–V–W system in combination with Monte Carlo (MC) simulations, we show that the phase stability and chemical short-range order (SRO) of the equiatomic quinary and five sub-quaternary systems, as well as their derivative alloys, can dramatically change the order–disorder transition temperatures (ODTT) as a function of alloy compositions. In particular, it has been found, that the equiatomic quaternary Ta–Ti–V–W and Cr–Ta–Ti–W alloys had the lowest order–disorder transition temperature (500 K) among all the analysed equiatomic compositions. In all investigated alloy systems, the strongest chemical ordering has been observed between Cr and V, which led to the conclusion that decreasing the concentration of either Cr or V might be beneficial in terms of decreasing the ODTT. It also predicts that increasing concentration of Ti significantly decreases the ODTT. Our analysis of chemical SRO as a function of alloy composition allows to understand the microstructure evolution of HEAs as a function of temperature in excellent agreement with available experimental observations. Importantly, our free energy of mixing and SRO calculations predict that the origin of precipitates formed by Cr- and V-rich in the sub-quaternary Cr–Ta–V–W system is driven by the thermodynamics. The modelling results are in an excellent agreement with experimental observation of Cr and V segregation in the W 0.38 Ta 0.36 Cr 0.15 V 0.11 alloy which in turns shows an exceptional radiation resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Investigation of LSM-YSZ Composite Cathode Performance Degradation with a Multistep Charge Transfer Model

The long-term performance degradation of LSM/YSZ composite cathodes is investigated via calibrated multiphysics simulation with a multistep oxygen reduction reaction (ORR) model and structural coarsening data from a phase field study. Multiphysics simulations, including a multistep ORR mechanism, are first developed for better understanding of the limiting processes in solid oxide fuel cells. The multistep ORR mechanism includes two parallel pathways, surface pathway and bulk pathway, which consist of elementary reaction steps. The multiphysics model is simultaneously calibrated with experimental polarization curves and impedance behavior for various air/fuel supply conditions. To our knowledge, this is the first time that a multistep ORR model is calibrated with such datasets. Next, the calibrated simulations are utilized to simulate a 2D half-cell constructed with measured microstructural data and random heterogeneity. Finally, the long-term performance degradation of the half-cell is predicted by the calibrated multiphysics model coupled with structural coarsening trends simulated using a phase field-based coarsening model. Degradation of both polarization curves and impedance behavior is investigated. Thorough analyses, including changes of contributions from different pathways, the resistance components, and overall reaction order, are performed to provide more insights into cathode performance degradation due to grain coarsening phenomena.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Tailoring the crystal growth of quartz on silicon for patterning epitaxial piezoelectric films

Epitaxial films of piezoelectric α-quartz could enable the fabrication of sensors with unprecedented sensitivity for prospective applications in electronics, biology and medicine. However, the prerequisites are harnessing the crystallization of epitaxial α-quartz and tailoring suitable film microstructures for nanostructuration. Here, we bring new insights into the crystallization of epitaxial α-quartz films on silicon (100) from the devitrification of porous silica and the control of the film microstructures: we show that by increasing the quantity of devitrifying agent (Sr) it is possible to switch from an α-quartz microstructure consisting of a porous flat film to one dominated by larger, fully dense α-quartz crystals. We also found that the film thickness, relative humidity and the nature of the surfactant play an important role in the control of the microstructure and homogeneity of the films. Via a multi-layer deposition method, we have extended the maximum thickness of the α-quartz films from a few hundreds of nm to the μm range. Moreover, we found a convenient method to combine this multilayer approach with soft lithography to pattern silica films while preserving epitaxial crystallization. This improved control over crystallization and the possibility of preparing patterned films of epitaxial α-quartz on Si substrates pave the path to future developments in applications based on electromechanics, optics and optomechanics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Effect of isovalent substitution on microstructure and phase transition of LaNb{sub 1−x}M{sub x}O{sub 4} (M=Sb, V or Ta; x=0.05–0.3)

LaNb{sub 1−x}M{sub x}O{sub 4} oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric measurements phase transition temperatures and thermal expansion coefficients of the studied materials were determined. It was shown that with increasing concentration of Sb the phase transition temperature decreases. Thermal expansion coefficient of the antimony substituted samples above the transition temperature is in the range from 8.1 to 9.1×10{sup −6} 1/K, whereas below the transition temperature the TEC value is between 14 and 17.3×10{sup −6} 1/K. Influence of Ta, V and Sb substitutions on the microstructure and grain size was studied. - Graphical abstract: Substitution of niobium by other pentavalent elements in LaNbO{sub 4} leads to change in phase transition temperature. In case of Sb substituent a shift of phase transition into the lower temperature region is observed. LaNb{sub 0.7}Sb{sub 0.3}O{sub 4} substitution allows to achieve material with tetragonal crystal structure at room temperature and no phase transition up to 1000 °C. - Highlights: • Antimony doped lanthanum niobate was successfully synthesized by solid state synthesis method. • The structural properties have been investigated by XRD and SEM. • The influence of doping on phase transition temperature has been studied.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Surfactant selection as a strategy for tailoring the structure and properties of UCT manganese oxides

Mesoporous manganese oxides were synthesized using the UCT inverse micelle templating method with four different Pluronic surfactants to investigate the effects on the morphology, microstructure and desulfurization behavior of these materials. All of the as-synthesized samples exhibited similar hierarchical microstructures, but the size and shape of the primary nanoparticles for each sample was different. The primary nanoparticle sizes for these samples vary between 2.3 and 7.0 nm. Most of the samples are crystalline and are composed of a mixture of Mn 3 O 4 and Mn 5 O 8 phases. The adsorption behavior of these samples was tested using a fixed bed reactor at a temperature of 200 °C. Microstructural analysis of the samples after the desulfurization tests revealed a transformation of the mesoporous manganese oxide to a dense manganese sulfide phase; this involves a volumetric expansion of the crystal, leading to densification and a rapid decay in the sorption capacity after the breakthrough point. The variation in the structure and properties of these materials is related to ratio of the PEO and PPO chain segment lengths in the Pluronic surfactants used. This indicates that the ratio must dictate the volume, shape and assembly of the inverse micelles in the UCT synthesis.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Screw-Dislocation-Driven Growth of 2D Perovskite Spiral Microplates

Two-dimensional (2D) organic–inorganic halide perovskites are solution-processable semiconductors that are promising for optoelectronic applications. Understanding crystallization mechanisms to achieve control over nanostructures is important for optimizing desired properties. Here we introduce a versatile strategy to synthesize spiral microplates of diverse 2D perovskites at the air–water interface through screw-dislocation-driven growth. Spirals of 11 2D perovskite compositions (LA) 2 (A) n−1 Pb n X 3n+1 with different spacer (LA) cations, A-cations, halide (X) anions, and n-number can be grown. They typically consist of single- or few-layer perovskite step heights but exhibit stacking complexity when multiple dislocations interact. The spiral microplates exhibit the characteristic optical properties (photoluminescence and second-harmonic generation) of the underlying 2D perovskites. Fluorescence-detected circular dichroism imaging shows that the chirality of the spiral center does not translate to the observed chiroptical properties of the microplate, consistent with the length scale of the chiral distortion. Furthermore, this solution growth of perovskite spirals diversifies the perovskite microstructures for optoelectronics and other applications.

2D halide perovskites↗