Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51

The impact assessment of eccentric installation and roughness change in piping on the orifice flow measurement

In orifice flowmeters used in nuclear power plants, requirements for the inner surface roughness of upstream piping and eccentric installation exist depending on certain standards. If these cannot be satisfied based on the installation condition, an appropriate error margin must be considered, although this remains to be clarified. In this research, quantitative data concerning the relative error of orifice flowmeters were obtained during experiments with the parameters of the inner surface roughness of upstream piping and the installation eccentricity of the orifice hole. The maximum Reynolds number of the experimental facility is about 1.6x10{sup 6}. In orifice flowmeters, the flow rate is calculated based on the differential pressure between upstream and downstream orifices and the peculiar discharge coefficient C. The latter value shows an upward trend with increasing roughness of piping, while change of 0.3% of C was observed in terms of roughness (case 2), which approaches the limits of the JIS standard. With significant roughness (Case 3) that exceeds five times the JIS standard, C is shown to have increased by about 1%. No influence was observed by varying the direction of eccentric installation, hence this was fixed and the amount of eccentricity was considered. Change in C of about 0.25% was observed when around twice the standard level of eccentricity was applied. The error margin data under conditions exceeding the JIS standard for the orifice flowmeter was obtained. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Influence of humidity, temperature, and annealing on microstructure and tensile properties of electrospun polyacrylonitrile nanofibers

This study investigates the microstructure and mechanical properties of electrospun nanofibers from polyacrylonitrile (PAN)-dimethylformamide (DMF) solution at different relative humidity (RH) in the range from 14% to 60% and two different temperatures (20 °C and 40 °C). Nanofibers produced at low RH (22% or less at 20 °C) exhibit relatively smooth surface and solid core, whereas at higher RH (30% or higher at 20 °C) rough surface and porous core are observed. The resulting morphology is explained by means of H 2 O/DMF/PAN ternary phase diagram. At higher RH, the water diffusion into polymer-solution jet brings thermodynamic instability into the system leading to separation of polymer-rich phase and polymer-lean phase, where the later contributes to porosity. Higher process temperature (40 °C) yields larger miscibility area in the ternary phase diagram leading to formation of porous structure at relatively higher RH (40%). Tensile strength of nanofibrous yarns is found to vary from 80 MPa to 130 MPa depending on the processing temperature and RH. The amount of porosity is found to affect the tensile properties of nanofibers most significantly, although diameter and crystallinity play important role. Annealing is found to alleviate surface roughness and porosity and increase crystallinity. Furthermore, tensile strength of nanofibrous yarns is found to improve by up to 25% after annealing.

36 MATERIALS SCIENCE↗

Distribution of Bound and Free Water in Anatomical Fractions of Pine Residues and Corn Stover as a Function of Biological Degradation

Biomass quality is influenced by water’s abundance, distribution, and status in relation to other chemical species within the polymer matrix. Water interacts with polymers that make up the cell walls, and these interactions govern the physical and chemical changes that occur during the storage and preprocessing of biomass feedstocks. Time-domain nuclear magnetic resonance (TD-NMR) was employed to explore variations in the physical constraints of water within the lignocellulosic microstructure in distinct anatomical fractions of biomass and as a function of biological degradation. The Carr–Purcell–Meiboom–Gill sequence, when combined with knowledge of the chemical composition and physical structure of pine residues and corn stover anatomical fractions, gives an accurate measurement of the bound and free water. In this work, the impacts of storage and biological degradation were investigated to elucidate changes in the status and distribution of water within distinct plant tissues. We also investigate how degradation during storage affects water interactions in different pine residues (e.g., bark, branch, and needle) and corn stover (e.g., cob, leaf, and stalk) anatomical fractions using transverse relaxation times (T2). As demonstrated herein, TD-NMR provides quantitative data on lignocellulosic biomass–water interactions within anatomical fractions, which can further aid in the investigation of preprocessing effects on feedstock quality. Our findings suggest that biological heating enhances biomass–water interactions at the cellular and macromolecular scale. In addition, analysis of three-dimensional scanning electron microscopy reconstructions indicates that surface roughness wavelengths align with microscale roughness, suggesting that pine forestry residue and corn stover particles have primarily hydrophobic exterior surfaces. Furthermore, this study offers multiscale insights into understanding the microstructure, wettability, and chemical environment that dictate diffusion, enzyme access, and recalcitrance of lignocellulosic biomass.

09 BIOMASS FUELS↗

Diazirine-based photo-crosslinkers for defect free fabrication of solution processed organic light-emitting diodes

The fabrication of solution deposited OLEDs is fraught with difficulties, largely due to the interlayer mixing and surface erosion during sequential deposition of the layers. We demonstrate that these problems can be circumvented by using photopolymerizable diazirine-based cross-linker capable of converting soluble organic materials into highly cross-linked insoluble networks. 3-Trifluoromethyl(aryl)diazirines photolyze readily upon the 10–15 min exposure of 365 nm UV irradiation to generate carbenes, which react with polymers or small molecules via C–H bond insertion producing highly cross-linked materials. This photo-generated cross-linking does not require any catalyst, initiator or short-wavelength UV light and is performed at room temperature, releasing molecular nitrogen as the only byproduct. To show the cross-linked polymer layers do not display inter-layer mixing, we deposited red-emitting regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) over cross-linked (10% cross-linker) blue emitting dioctyl polyfluorene (PFO) layer. The overlaid layers showed clear and well-defined boundary with no interlayer mixing. The surface morphology of the solution deposited layers was investigated by AFM to show that the cross-linked layers exhibited significant decrease in surface roughness. This is also shown on the example of the hole transporting material 4,4'-bis[N-(1-naphthyl)-N-phenylamino]-biphenyl (NPB) which displayed roughness average to decrease from 6.4 nm to 1.0 nm. The effect of decreased surface roughness on the performance of phosphorescent OLEDs was investigated by fabricating devices with configuration of ITO/PEDOT:PSS/NPB:(0%/5%/10%) cross-linker/MCP:6% Ir(mppy) 3 /TPBI/CsF/Al. Furthermore, following the diazirine-mediated cross-linking, the OLEDs displayed a decrease in turn-on voltage from 3.8 V to 3.0 V along with a six-fold enhancement of external quantum efficiency (EQE max ) from 1.1% to 6.8% and maximum luminous efficiency increase from 3.8 cd A -1 to 22.9 cd A -1 . These results demonstrate that the simple diazirine mediated photo-cross-linking using mild conditions compatible with organic layers is a promising strategy for improving the performance of the solution-processed OLEDs.

36 MATERIALS SCIENCE↗

Influence of Spatter on Porosity, Microstructure, and Corrosion of Additively Manufactured Stainless Steel Printed Using Different Island Size

Specimens of 316 L stainless steel were printed using laser powder bed fusion (LPBF), a popular metal additive manufacturing (AM) technique, with varying island sizes. Not many researchers have considered the impact of spatter while optimizing LPBF printing parameters. In this research, the influence of spatter was considered while also investigating the effect of varied island size on the microstructure, surface roughness, microhardness, and corrosion resistance of LPBF-316 L. No correlation was observed between surface roughness or microhardness and minor variations in island size. However, a correlation was drawn between varied island sizes and porosity in LPBF-316 L. The specimens associated with larger island sizes showed significantly enhanced corrosion resistance due to fewer manufacturing defects and reduced porosity, attributed to the minimal influence of the spatter. Based on analysis, the LPBF parameters were revised, which lead to superior corrosion resistance of LPBF-316 L, attributed to high density and reduced porosity.

36 MATERIALS SCIENCE↗

A microcomputer program for estimating low altitude wind and turbulence fields

Past efforts to develop methods for objective wind analysis and to provide turbulence estimates to pilots are reviewed. The present approach involves a wind module and a turbulence module. The wind module extends the critical dividing streamline concept and past developments in mass-conserving wind interpolation schemes. The turbulence module is based on recent efforts to develop practical atmospheric turbulence parameterization schemes based on lapse rate, wind shear, surface heating, and surface roughness. The lapse rate and wind shear are readily obtained from the wind module. Surface roughness and heating come from land use information and net radiation estimates derived from cloud cover, terrain slope, local time, and latitude. This system is argued to have considerable potential for providing useful online information for many kinds of aircraft operations.

Ludwig, F. L.↗

Characteristics of Pressure Sensitive Paint Intrusiveness Effects on Aerodynamic Data

One effect of using pressure sensitive paint (PSP) is the potential intrusiveness to the aerodynamic characteristics of the model. The paint thickness and roughness may affect the pressure distribution, and therefore, the forces and moments on the wind tunnel model. A study of these potential intrusive effects was carried out at NASA Langley Research Center where a series of wind tunnel tests were conducted using the Modem Design of Experiments (MDOE) test approach. The PSP effects on the integrated forces were measured on two different models at different test conditions in both the Low Turbulence Pressure Tunnel (LTPT) and the Unitary Plan Wind Tunnel (UPWT) at Langley. The paint effect was found to be very small over a range of Reynolds numbers, Mach numbers and angles of attack. This is due to the very low surface roughness of the painted surface. The surface roughness, after applying the NASA Langley developed PSP, was lower than that of the clean wing. However, the PSP coating had a localized effects on the pressure taps, which leads to an appreciable decrease in the pressure tap reading.

Amer, Tahani R.↗

Characterization of Pressure Sensitive Paint Intrusiveness Effects on Aerodynamic Data

One effect of using pressure sensitive paint (PSP) is the potential intrusiveness to the aerodynamic characteristics of the model. The paint thickness and roughness may affect the pressure distribution. and therefore, the forces and moments on the wind tunnel model. A study of these potential intrusive effects was carried out at NASA Langley Research Center where a series of wind tunnel tests were conducted using the Modem Design of Experiments (MDOE) test approach. The PSP effects on the integrated forces were measured on two different models at different test conditions in both the Low Turbulence Pressure Tunnel (LTPT) and the Unitary Plan Wind Tunnel (UPWT) at Langley. The paint effect was found to be very small over a range of Reynolds numbers, Mach numbers and angles of attack. This is due to the very low surface roughness of the painted surface. The surface roughness, after applying the NASA Langley developed PSP, was lower than that of the clean wing. However, the PSP coating had a localized effects on the pressure taps, which leads to an appreciable decrease in the pressure tap reading.

Amer, Tahani R.↗

On the dynamic roughening transition in nanocomposite film growth

Surface roughness and dynamic growth behavior of TiC/a-C nanocomposite films deposited by nonreactive pulsed-dc (p-dc) magnetron sputtering were studied using atomic force microscopy, cross-sectional scanning, and transmission electron microscopy. From detailed analyses of surface morphology and growth conditions, it is concluded that a transition in growth mechanisms occurs, i.e., a mechanism dominated by geometric shadowing at a p-dc frequency of 100 kHz evolving to a surface diffusion mechanism driven by impact-induced atomistic downhill flow process by Ar{sup +} ions at a p-dc frequency of 350 kHz. It is shown that rapid smoothening of initially rough surfaces with rms roughness from {approx}6 to <1 nm can be effectively achieved with p-dc sputtering at 350 kHz pulse frequency, leading to a transition from a strong columnar to a columnar-free microstructure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Monolayer graphene growth on sputtered thin film platinum

It is demonstrated that sputtered thin film platinum (Pt) can be used as a catalytic metal for graphene growth on metal. During the crystallization annealing, the sputtered Pt is crystallized mostly into Pt (111) orientation, maintaining excellent surface roughness with no sign of agglomeration. The relatively lower carbon solubility in Pt and the good surface roughness of the thin film Pt enable us to form a uniform monolayer graphene on Pt over the entire region of the thin film Pt/SiO{sub 2}/Si substrate by carbon dissolution and segregation method processed in a methane ambient. The monolayer graphene grown on Pt has been successfully transferred to SiO{sub 2}/Si substrate by simple wet etching of Pt. The results of Raman spectroscopic and scanning tunneling microscopic measurements of the synthesized graphene layer are presented.

36 MATERIALS SCIENCE↗

Experimental approach for development of a powder spreading metric in additive manufacturing

The powder spreading is a vital step of powder-based additive manufacturing (AM) processes. The quality of spread powder can considerably influence the properties of fabricated parts. Poorly packed powder beds with high surface roughness result in printed part layers with large porosity and low dimensional accuracy, leading to poor mechanical properties. Therefore, the powder spreadability and its dependence on process parameters and powder characteristics should be quantified to improve the efficiency of powder-based AM methods. This study proposes a novel dimensionless powder spreadability metric that can be commonly used in different powder-based AM processes. The quality of spread powder in terms of powder bed density and surface roughness was evaluated by adjusting the process parameters including recoating velocity and layer thickness, and powder characteristics including particle size distribution. In addition, the dynamic repose angle was proposed and examined as another powder spreadability metric. Furthermore, the results showed that these two proposed metrics were strongly correlated and lower recoating velocity and larger layer thickness led to higher spreadability and lower dynamic repose angle.

36 MATERIALS SCIENCE↗

NOAA's oceanography studies under the Earth Resources Survey Program

Some results are presented of Earth Resources Survey Program studies conducted on: (1) Defining and developing methods of suppressing system noise and cloud contamination in satellite measurements of infrared window radiation. (2) Relating sea surface temperature patterns in the Gulf Stream and Gulf of Mexico to associated thermal front structure with aid of infrared data from Nimbus or ITOS. (3) Testing the feasibility of mapping sea surface roughness and low level wind speed over tropical oceans by means of ATS imagery in sun glitter zones. (4) Microwave radiometer measurements from aircraft and their usefulness and limitations for all-weather mapping of surface roughness, sea ice conditions, and possible surface temperature. (5) Evaluation of scanning radiometer data from ITOS for purposes of mapping snow and ice conditions.

Mcclain, E. P.↗

Useful Radar Data for Mars 2001 Landing Site Selection

Radar data, of both Doppler-only and delay-Doppler varieties, played a useful role in the landing site certification process for Mars Pathfinder. Radar provides information on the elevation of the planetary surface, on its radar reflectivity and on the surface roughness. The elevation is important for proper entry, descent and landing, as is the reflectivity if a radar altimeter is to be used on the lander. Both the reflectivity and the surface roughness can measure the rockiness of the surface, important for a safe landing, as well as for rover trafficability. The spatial resolution of this Earth-based remote sensing technique is around 10 km in longitude by some 150 km in latitude. In the case of Pathfinder the regionally averaged properties were confirmed by ground truth at the landing site in Ares Vallis. The landing site assessment for Pathfinder relied principally on data from the 1995 Mars opposition when sub-Earth latitudes on Mars ranged from 16 to 22 degrees north. Data from earlier oppositions (1992-93, 1990, 1988-89) are available and cover latitudes from 25 south to 25 north at various longitudes. The available data will be presented at the symposium. The data are of varying quality, although ranging data is available for about 20 radar tracks per opposition, reflectivity and roughness analyses may not always be possible. Some older data are also available (1982, 1980) with range-only information.

Haldemann, A. F. C.↗

Etching studies of silica glasses in SF{sub 6}/Ar inductively coupled plasmas: Implications for microfluidic devices fabrication

To fabricate microlaboratories, commercially available silica glasses represent a good alternative to the expensive quartz or fused silica substrates. Therefore, the authors have here investigated the behavior of four of them--Vycor, Pyrex, D263, and AF45--in SF{sub 6} and SF{sub 6}/Ar inductively coupled plasmas. Using Vycor, a material close to pure SiO{sub 2}, as a reference, they demonstrated that the etch rate negatively correlates with the global content in metallic oxides. However, no such clear trend was found for the surface roughness and they hypothesize that the large asperities (>500 nm) sometimes observed might be due to local variation in the glass surface composition. Furthermore, investigations on the influence of the plasma conditions (i.e., source power, dc self-bias, gas mixture, and pressure) on the etch rate, surface chemistry, and surface morphology, as well as positive ion current and fluorine concentration measurements, enable them to unravel an ion enhanced chemical etching mechanism, where stronger ion assistance is needed when more metallic oxides are present. By increasing the ion to neutral flux ratio, they consequently could, for all the materials, reduce the surface roughness to less than 5 nm while maintaining etch rates around 150 nm/min. These conditions have further been used to optimize pattern transfer experiments.

36 MATERIALS SCIENCE↗

Visible light scatter measurements of the Advanced X-ray Astronomical Facility /AXAF/ mirror samples

NASA is studying the properties of mirror surfaces for X-ray telescopes, the data of which will be used to develop the telescope system for the Advanced X-ray Astronomical Facility. Visible light scatter measurements, using a computer controlled scanner, are made of various mirror samples to determine surface roughness. Total diffuse scatter is calculated using numerical integration techniques and used to estimate the rms surface roughness. The data measurements are then compared with X-ray scatter measurements of the same samples. A summary of the data generated is presented, along with graphs showing changes in scatter on samples before and after cleaning. Results show that very smooth surfaces can be polished on the common substrate materials (from 2 to 10 Angstroms), and nickel appears to give the lowest visible light scatter.

Griner, D. B.↗

Adsorption of silica colloids onto like-charged silica surfaces of different roughness

Particle adsorption was explored in a model optical polishing system, consisting of silica colloids and like-charged silica surfaces. The adsorption was monitored in situ under various suspension conditions, in the absence of surfactants or organic modifiers, using a quartz crystal microbalance with dissipation monitoring (QCM-D). Changes in surface coverage with particle concentration, particle size, pH, ionic strength and ionic composition were quantified by QCM-D and further characterized ex situ by atomic force microscopy (AFM). A Monte Carlo model was used to describe the kinetics of particle deposition and provide insights on scaling with particle concentration. Transitions from near-zero adsorption to measurable adsorption were compared with equilibrium predictions made using the Deraguin-Verwey-Landau-Overbeek (DLVO) theory. In addition, the impact of silica surface roughness on the propensity for particle adsorption was studied on various spatial scale lengths by intentionally roughening the QCM sensor surface using polishing methods. It was found that a change in silica surface roughness at the AFM scale from 1.3 nm root-mean-square (rms) to 2.7 nm rms resulted in an increase in silica particle adsorption of 3-fold for 50-nm diameter particles and 1.3-fold for 100-nm diameter particles—far exceeding adsorption observed by altering suspension conditions alone, potentially because roughness at the proper scale reduces the total separation distance between particle and surface.

36 MATERIALS SCIENCE↗

Effects of Biomass Accessibility and Klason Lignin Contents during Consolidated Bioprocessing in Populus trichocarpa

The bacterium Clostridium thermocellum offers a distinct and integrated approach to ethanol production through consolidated bioprocessing (CBP). The Simons’ stain technique, which assays the accessibility of lignocellulosic biomass, has been traditionally applied to fungal cellulase systems; however, its application to CBP has not been fully explored. For this reason, the structural properties of eight Populus trichocarpa with either high or low biomass densities were compared in this paper to determine bioconversion differences during separate hydrolysis and fermentation (SHF) and CBP with C. thermocellum. Simons’ staining generally identifies low density poplar as more accessible than high density poplar. Additionally, low density P. trichocarpa generally contained less Klason lignin than high density poplar. SHF and CBP treatments consistently identified BESC-7 (high density, low accessibility, low surface roughness) as a low ethanol yielding biomass and GW-9914 (low density, high accessibility, high surface roughness) as a high ethanol yielding biomass. Upon further investigation, BESC-7 also contained a high Klason lignin content (~25%), while GW-9914 had a low lignin content (~20%). Cellulose degree of polymerization (DP) measurements exhibited a weak linear correlation with accessibility (r 2 = 0.17). Finally, therefore, the ethanol yields were correlated with accessibility and lignin content extremes but not cellulose DP.

09 BIOMASS FUELS↗

Hydrologic Connectivity and Patch‐To‐Hillslope Scale Relations in Dryland Ecosystems

Abstract In drylands, runoff during storms redistributes water and nutrients from bare soil areas to vegetated patches, subsidizing vegetation with additional resources. The extent of this redistribution depends on the interplay between surface roughness and permeability; greater permeability in vegetated patches promotes run‐on to vegetation, but greater surface roughness diverts runoff, producing tortuous flow paths that bypass vegetation. Here, this interplay is examined in virtual experiments using the 2D Saint Venant Equations to measure runoff connectivity. Flowpaths are delineated using tracers advected by the flow. Distances between tracer sources and sinks along flowpaths measure hydrologic connectivity at two lengthscales: connectivity to the hillslope outlet and within‐slope source‐sink connectivity. Differences between these connectivity lengthscales indicate how flow may “by‐pass” vegetated patches within hillslopes. At the hillslope scale, a derived power‐law relation between the runoff coefficient and outlet connectivity describes hillslope water losses, providing a foundation for identifying landscapes likely to shed water.

54 ENVIRONMENTAL SCIENCES↗