Search NASA⌕ Search

SEARCH · Search NASA

Results for “scanning electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Structural, magnetic and optical properties of a dilute magnetic semiconductor based on Ce{sub 1−x}Co{sub x}O{sub 2} thin film grown on LaAlO{sub 3}

Highlights: • Co doped CeO{sub 2} was grown on LaAlO{sub 3} (0 0 1) via a modified sol–gel spin-coating technique. • The concentration of the Co ions was varied from 1 to 15 at.%. • The incorporation of 5 at.% of Mn ions was found to provide formation of exceptionally magnetic moment. • This amount demonstrated a giant magnetic moment of 1.09 μ{sub B}/Co. • This amount reduced the optical band gap and enhanced the optical performance. - Abstract: The enhancement of the room temperature ferromagnetism and optical properties of the dilute magnetic metal oxides is a crucial clue to construct spin-based optoelectronic devices. In this work, Ce{sub 1−x}Co{sub x}O{sub 2} (0.01 ≤ x ≤0.15) thin films were prepared via ethylene glycol modified sol–gel spin coating technique on the LaAlO{sub 3} (0 0 1) substrate to enhance their room temperature ferromagnetism and optical properties. The structures, magnetic and optical properties of the prepared films were characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, SQUID magnetometer, X-ray photoelectron spectroscopy and UV–vis spectrophotometer. The results demonstrated that a single phase cubic structure was formed, implying the substitution of Co ions into the Ce ions sites. The prepared films showed room temperature ferromagnetism with saturation magnetic moment of 1.09 μ{sub B}/Co was achieved for 5 at.% Co-doped CeO{sub 2}. This film exhibited high optical transparency of 85% and low optical band energy gap of 3.39 eV. The improved magnetic and optical properties are argued to the increase of the density of the oxygen vacancies into the cerium oxide crystal structure due to the incorporation of Co ions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain-induced majority carrier inversion in ferromagnetic epitaxial LaCo O 3 - δ thin films

Tensile-strained LaCoO 3-δ thin films are ferromagnetic, in sharp contrast to the zero-spin bulk, although no clear consensus has emerged as to the origin of this phenomenon. While magnetism has been heavily studied, relatively little attention has been paid to electronic transport, due to the insulating nature of the strain-stabilized ferromagnetic state. Here, structure, magnetism, and transport are studied in epitaxial LaCoO 3-δ films (10–22-nm thick) on various substrates (from 1.4% compressive to 2.5% tensile strain), using synchrotron x-ray diffraction, scanning probe and transmission electron microscopy, magnetometry, polarized neutron reflectometry, resistivity, and Hall effect. High quality, smooth films are obtained, exhibiting superstructures associated with both oxygen vacancy ordering and periodic in-plane ferroelastic domains. Consistent with prior work, ferromagnetism with an approximately 80–85 K Curie temperature is observed under tension; polarized neutron reflectometry confirms a relatively uniform magnetization depth profile, albeit with interfacial dead layer formation. Electrical transport is found to have similar semiconducting nature to bulk, but with reduced resistivity and activation energy. Hall effect measurements, however, reveal a striking inversion of the majority carrier type, from p-type in the bulk and under compression to n-type under tension. While thus far overlooked, ferromagnetism in epitaxial LaCoO 3-δ films is thus directly correlated with n-type behavior, providing important insight into the ferromagnetic state in this system. Here, aided by density functional theory calculations, these results are interpreted in terms of tensile-strain-induced orbital occupation and band structure changes, including a rapid decrease in effective mass at the e g -derived conduction band minimum, and corresponding increase at the valence band maximum.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Insights into the dominant factors of porous gold for CO oxidation

Three different porous Au catalysts that exhibit high catalytic activity for CO oxidation were prepared by the leaching of Al from an intermetallic compound, Al{sub 2}Au, with 10 wt. %-NaOH, HNO{sub 3}, or HCl aqueous solutions. The catalysts were investigated using Brunauer-Emmett-Teller measurements, synchrotron X-ray powder diffraction, hard X-ray photoelectron spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy (TEM). Broad diffraction peaks generated during the leaching process correlated with high activity for all the porous Au catalysts. CO oxidation catalyzed by porous Au leached with NaOH and HNO{sub 3} is considered to be dominated by different mechanisms at low (< 320 K) and high (> 370 K) temperatures. Activity in the low-temperature region is mainly attributed to the perimeter interface between residual Al species (AlO{sub x}) and porous Au, whereas activity in the high-temperature region results from a high density of lattice defects such as twins and dislocations, which were evident from diffraction peak broadening and were observed with high-resolution TEM in the porous Au leached with NaOH. It is proposed that atoms located at lattice defects on the surfaces of porous Au are the active sites for catalytic reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

La{sub 2}Zr{sub 2}O{sub 7} Doping Effects on MOD-SmBCO-Coated Conductors

SmBa{sub 2}Cu{sub 3}O{sub 7-δ} (SmBCO)-coated conductors containing La{sub 2}Zr{sub 2}O{sub 7} (LZO) artificial pinning centers (APCs) were fabricated on buffered Hastelloy substrates by low fluorine metal organic deposition method (MOD). The properties of LZO-doped SmBCO film were systematically studied by x-ray diffraction (XRD), Raman spectra, and scanning electron microscope (SEM). Higher critical current density (J{sub c}) values not only in self field but also in applied magnetic field were obtained by moderate LZO doping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Supercritical CO{sub 2} mediated synthesis and catalytic activity of graphene/Pd nanocomposites

Highlights: • RGO/Pd composite was efficiently prepared via a facile method in supercritical CO{sub 2}. • Graphene sheets were coated uniformly with Pd nanoparticles with a size of ∼8 nm. • Composites exhibited excellent catalytic activity in the Suzuki reaction even after 10 cycles. - Abstract: Graphene sheets were decorated with palladium nanoparticles using a facile and efficient method in supercritical CO{sub 2}. The nanoparticles were formed on the graphene sheets by the simple hydrogen reduction of palladium(II) hexafluoroacetylacetonate precursor in supercritical CO{sub 2}. The product was characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and X-ray photoelectron spectroscopy. Highly dispersed nanoparticles with various sizes and shapes adhered well to the graphene sheets. The composites showed high catalytic activities for the Suzuki reaction under aqueous and aerobic conditions within 5 min. The effects of the different Pd precursor loadings on the catalytic activities of the composites were also examined.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Fast and low concentration detection of liquefied petroleum gas by Au-activated ZnO sensor

Highlights: • As-synthesized and Au-activated ZnO samples are studied as an LPG sensor. • The operating temperature of ZnO sensor decreases after activation by Au layer. • LPG sensitivity of ZnO sensor shows a significant enhancement after activation. • The Au-activated ZnO sensor is able to quick response to LPG. - Abstract: The development of a reliable and fast liquefied petroleum gas (LPG) sensor due to its highly inflammable and explosive nature is crucial to ensure a safe and healthy environment. In this research, as-synthesized and Au-activated nanostructured ZnO were prepared and investigated as an LPG sensor. The samples were structurally and morphologically characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). LPG sensitivity of the sample shows a significant enhancement after activation with the Au layer. The results also show that the Au-activated sample is able to detect the LPG in the range of 100–1000 ppm (and more concentrations) with the response time of 33-18 S that can be remarkable compared to the previous reports attributed to different materials and technologies.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2016

Enhanced conductivity at orthorhombic–rhombohedral phase boundaries in BiFeO 3 thin films

Enhanced properties in modern functional materials can often be found at structural transition regions, such as morphotropic phase boundaries (MPB), owing to the coexistence of multiple phases with nearly equivalent energies. Strain-engineered MPBs have emerged in epitaxially grown BiFeO 3 (BFO) thin films by precisely tailoring a compressive misfit strain, leading to numerous intriguing phenomena, such as a massive piezoelectric response, magnetoelectric coupling, interfacial magnetism and electronic conduction. Recently, an orthorhombic–rhombohedral (O–R) phase boundary has also been found in tensile-strained BFO. In this study, we characterise the crystal structure and electronic properties of the two competing O and R phases using X-ray diffraction, scanning probe microscope and scanning transmission electron microscopy (STEM). We observe the temperature evolution of R and O domains and find that the domain boundaries are highly conductive. Temperature-dependent measurements reveal that the conductivity is thermally activated for R–O boundaries. STEM observations point to structurally wide boundaries, significantly wider than in other systems. Furthermore, we reveal a strong correlation between the highly conductive domain boundaries and structural material properties. These findings provide a pathway to use phase boundaries in this system for novel nanoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Enhancement of the photo conversion efficiencies in Cu(In,Ga)(Se,S){sub 2} solar cells fabricated by two-step sulfurization process

Cu(In,Ga)(Se,S){sub 2} (CIGSS) absorber layers were fabricated by using a modified two-stage sputter and a sequential selenization/sulfurization method, and the sulfurization process is changed from one-step to two-step. The two-step sulfurization was controlled with two different H{sub 2}S gas concentrations during the sulfurization treatment. This two-step process yielded remarkable improvements in the efficiency (+0.7%), open circuit voltage (+14 mV), short circuit current (+0.23 mA/cm{sup 2}), and fill factor (+0.21%) of a CIGSS device with 30 × 30 cm{sup 2} in size, owing to the good passivation at the grain boundary surface, uniform material composition among the grain boundaries, and modified depth profile of Ga and S. The deterioration of the P/N junction quality was prevented by the optimized S content in the CIGSS absorber layer. The effects of the passivation quality at the grain boundary surface, the material uniformity, the compositional depth profiles, the microstructure, and the electrical characteristics were examined by Kelvin probe force microscopy, X-ray diffraction, secondary ion mass spectrometry, scanning electron microscopy, and current-voltage curves, respectively. The two-step sulfurization process is experimentally found to be useful for obtaining good surface conditions and, enhancing the efficiency, for the mass production of large CIGSS modules.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Fe(III) Oxide Mineralogy and Phosphate on Fe(II) Secondary Mineral Formation during Microbial Iron Reduction

The bioreduction of Fe(III) oxides by dissimilatory iron-reducing bacteria may result in the formation of a suite of Fe(II)-bearing secondary minerals, including magnetite (a mixed Fe(II)/Fe(III) oxide), siderite (Fe(II) carbonate), vivianite (Fe(II) phosphate), chukanovite (ferrous hydroxy carbonate), and green rusts (mixed Fe(II)/Fe(III) hydroxides). In an effort to better understand the factors controlling the formation of specific Fe(II)-bearing secondary minerals, we examined the effects of Fe(III) oxide mineralogy, phosphate concentration, and the availability of an electron shuttle (9,10-anthraquinone-2,6-disulfonate, AQDS) on the bioreduction of a series of Fe(III) oxides (akaganeite, feroxyhyte, ferric green rust, ferrihydrite, goethite, hematite, and lepidocrocite) by Shewanella putrefaciens CN32, and the resulting formation of secondary minerals, as determined by X-ray diffraction, Mössbauer spectroscopy, and scanning electron microscopy. The overall extent of Fe(II) production was highly dependent on the type of Fe(III) oxide provided. With the exception of hematite, AQDS enhanced the rate of Fe(II) production; however, the presence of AQDS did not always lead to an increase in the overall extent of Fe(II) production and did not affect the types of Fe(II)-bearing secondary minerals that formed. The effects of the presence of phosphate on the rate and extent of Fe(II) production were variable among the Fe(III) oxides, but in general, the highest loadings of phosphate resulted in decreased rates of Fe(II) production, but ultimately higher levels of Fe(II) than in the absence of phosphate. In addition, phosphate concentration had a pronounced effect on the types of secondary minerals that formed; magnetite and chukanovite formed at phosphate concentrations of ≤1 mM (ferrihydrite), <~100 µM (lepidocrocite), 500 µM (feroxyhyte and ferric green rust), while green rust, or green rust and vivianite, formed at phosphate concentrations of 10 mM (ferrihydrite), ≥100 µM (lepidocrocite), and 5 mM (feroxyhyte and ferric green rust). These results further demonstrate that the bioreduction of Fe(III) oxides, and accompanying Fe(II)-bearing secondary mineral formation, is controlled by a complex interplay of mineralogical, geochemical, and microbiological factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Microscopic analysis of irradiated UN–Mo–W for space nuclear propulsion

Nuclear propulsion is an effective method of providing thrust in deep space, allowing for shorter mission duration for long-term surface missions to Mars. The fuel for nuclear propulsion systems must exhibit superior mechanical and thermal properties, to decrease the possibility of fuel failure and to increase reactor efficiency. Here, the objective of the Sirius project is to fabricate and irradiate cermet fuels at the Idaho National Laboratory Transient Reactor Facility to determine the properties of the fuel after irradiation at prototypical nuclear propulsion start-up conditions. The Sirius project featured 3 test capsules, Sirius-1 featured uranium nitride fuel dispersed in a matrix of tungsten and rhenium, while Sirius-2A and -2B featured uranium nitride-molybdenum-tungsten fuel (UN-Mo-W). The fuel samples from the Sirius-2A and -2B capsules were examined after irradiation using optical microscopy, scanning electron microscopy, and X-ray diffraction analyses. The mechanical properties of the fuel from Sirius-2A and -2B are discussed in a previous work. In this study, the results of the optical microscopy, scanning electron microscopy, and X-ray diffraction analyses are discussed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

SEM and TEM characterization of microstructure of stainless steel composites reinforced with TiB{sub 2}

Steel-8TiB{sub 2} composites were produced by two new sintering techniques, i.e. Spark Plasma Sintering (SPS) and High Pressure-High Temperature (HP-HT) sintering. This study discusses the impact of these sintering methods on the microstructure of steel composites reinforced with TiB{sub 2} particles. Scanning electron microscopy (SEM), wavelength dispersive spectroscopy (WDS), X-ray diffraction, electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) were used to analyze the microstructure evolution in steel matrix composites. The results of microscopic examinations revealed a close relationship between the composite microstructure and the methods and conditions of sintering. Substantial differences were observed in the grain size of materials sintered by HP-HT and SPS. It has been demonstrated that the composites sintered by HP-HT tend to form a chromium-iron-nickel phase in the steel matrix. In contrast, the microstructure of the composites sintered by SPS is characterized by the presence of complex borides and chromium-iron phase. - Highlights: •The steel-8TiB{sub 2} composites were fabricated by Spark Plasma Sintering (SPS) and High Pressure-High Temperature (HP-HT). •Sintering techniques has an important effect on changes in the microstructure of steel-8TiB{sub 2} composites. •New phases of different size and morphology were identified.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Development and Mechanical Properties of In Situ Al{sub 3}Ti-Reinforced Nanostructured AA6061 via Mechanical Alloying

Mechanical alloying (MA) was used to disperse 10 wt.% titanium powder in AA6061 powder. The resultant powder was degassed, and differential scanning calorimetry was performed to determine the temperature for formation of titanium aluminide (Al{sub 3}Ti). The MA powder was characterized by field emission scanning electron microscopy, x-ray diffraction (XRD) and transmission electron microscopy (TEM). Subsequently, the MA powder was consolidated by spark plasma sintering (SPS) at 500 °C under a pressure of 50 MPa. XRD and x-ray energy-dispersive spectroscopy of spark plasma sintered compact revealed in situ formation of Al{sub 3}Ti. TEM micrographs of spark plasma sintered sample exhibited Al nanograins (average size 50 nm) in the AA6061 matrix along with the dispersed Al{sub 3}Ti (average size 200 nm). Hardness, yield strength and compressive strength of the SPSed samples were also evaluated and compared with AA6061.

36 MATERIALS SCIENCE↗
DOE OSTI2018

In situ analysis of plasticity and damage nucleation in a Ti-6Al-4V alloy and laser weld

Highlights: • EBSD in situ tensile test on a Ti-6Al-4V alloy and laser weld • Mainly prismatic, basal and pyramidal a slip activity in the base metal • Damage nucleation in the vicinity of the β phase and at α grain boundaries • Alignment of 10-10 crystallographic direction with the tensile axis in the α′ laths of the weld metal • Crack initiation along specific laths interfaces, former β grain boundary or twinned martensite laths in the weld metal The present work addresses the mechanisms of plasticity and damage nucleation in a Ti-6Al-4V alloy and its laser weld. To this end, in situ tensile tests are performed in a Scanning Electron Microscope (SEM) equipped with a Electron BackScatter Diffraction (EBSD) camera. The slip activity is automatically analyzed using a modified Schmid analysis. It is shown that the slip activity of the base metal consists mainly in prismatic, basal and pyramidal a slip. Damage nucleation in the vicinity of the β phase and at α grain boundaries is also evidenced in the base metal. In the α{sup ′} weld metal (a microstructure similar to the one often obtained in additive manufacturing Ti-alloy parts), plastic deformation results in a crystallographic rotation of the laths tending to align the 〈10 1-bar 0〉 direction with the tensile axis. The rare events of crack initiation in the martensite are shown to occur along specific laths interfaces, former β grain boundary or twinned martensite needles.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Adsorption and self-assembled structures of sexithiophene on the Si(111)-√(3)×√(3)-Ag surface

The adsorption and self-assembled structures of α-sexithiophene (α-6T) have been investigated on a Si(111)-Ag surface using scanning tunneling microscopy (STM), low-energy electron diffraction, and density functional theory calculations. The adsorbed α-6T molecules are arranged into unidirectional molecular rows with a side-by-side orientation. The molecular rows reveal three kinds of appearances in the filled-state STM images, which reflect the distinct adsorption sites. From tunneling spectroscopy, we find that the filled-state STM images of α-6T should be influenced by the surface states of Si(111)-Ag. At one monolayer coverage, sequentially ordering of the triple molecular rows results in the close-packed arrangement of the α-6T overlayer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Decagonal Sn clathrate on d-Al-Ni-Co

Decagonal quasiperiodic ordering of Sn thin films on d-Al-Ni-Co is shown based on scanning tunneling microscopy (STM), low-energy electron diffraction, and density functional theory (DFT). Interestingly, the decagonal structural correlations are partially retained even up to a large film thickness of 10 nm grown at 165±10K. The nucleation centers called “Sn white flowers” identified by STM at submonolayer thickness are recognized as valid patches of the decagonal clathrate structure with low adsorption energies of these motifs. Due to the excellent lattice matching (to within 1%) between columns of Sn dodecahedra in the clathrate structure and pentagonal motifs at the d-Al-Ni-Co surface, the interfacial energy favors clathrate over the competing Sn crystalline forms. DFT study of the Sn/Al-Ni-Co composite model shows good mechanical stability, as shown by the work of separation of Sn from Al-Ni-Co slab that is comparable to the clathrate self-separation energy. Finally, the relaxed surface terminations of the R 2 T 4 clathrate approximant are in self-similarity correspondence with the motifs observed in the STM images from monolayer to the thickest Sn film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

LDRD 22A1059-068FP Tailoring the Properties of Multi-Phase Materials Through the Use of Correlative Microscopy and Machine Learning - Poster

High strength alloys with good ductility, hardness, and toughness are needed to meet stringent design requirements for extreme environments. One complication in this pursuit is the evidence that metals rarely exhibit both high strength and good fracture toughness as the underlying mechanisms work in opposition. An exception to this behavior is found in multiphase alloys that form complex microstructures of mixed phases with variable grain sizes and shapes that provide increased fracture toughness by the arrangement of their constituent elements. We propose to explore this phenomenon using state-of-the-art machine learning (ML) techniques in a new and novel manner to identify and correlate the critical microstructural features in a Titanium-10Vanadium-2Iron-3Aluminum (Ti-10V-2Fe-3Al) alloy that is reported to exhibit high strength and fracture toughness. Additionally, we will employ multiple, complementary characterization techniques such as optical microscopy, electron backscatter diffraction (EBSD), energy dispersive spectroscopy (EDS) and scanning electron microscopy to provide multi-layer, quantitative ground truth measures of the microstructures. This data will be used to train a Convolutional Neural Network (CNN) in a semi-supervised environment to identify key microstructural features such as ? platelet dimensions and locations and ?/? phase boundaries and correlate those features with the strength and toughness. Here the ? and ? nomenclature refers to hexagonal close pack (hcp) and body center cubic (bcc) crystal structures, respectively. Previous work has focused on popular alloys and typically used one characterization technique. This research is focused on a promising titanium alloy, uses multiple complimentary characterization tools to provide precise microstructural information and correlates to improved fracture toughness. The resulting ML tool can be trained for additional microstructural features, different alloy(s), and or target mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

In-situ observations of cyclic deformation in an extruded Mg-2Nd-1Y-0.1Zr-0.1Ca alloy

In this study, the evolution of deformation mechanisms during cyclic loading in an extruded, solution-treated Mg–2Nd–1Y–0.1Zr–0.1Ca alloy was investigated using a combination of in-situ loading, scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and focused ion beam (FIB) nanofabrication. The initial microstructure exhibited a random crystallographic texture with no preferred grain orientation. Flat, rectangular dog-bone specimens were subjected to load-controlled, fully reversed fatigue for 50 cycles, during which the same region was sequentially mapped to track microstructural changes. After 10 cycles of loading deformation twins were observed. During tensile reloading detwinning or narrowing of those twinned regions occurred. After 20 cycles, detwinning ceased and residual twins remained in the material. SEM imaging revealed numerous surface slip traces after cyclic loading. EBSD-assisted slip trace analysis identified the activation of prismatic and pyramidal < c+a> slip systems during low-cycle fatigue. Site-specific scanning transmission electron microscopy (STEM) further revealed that deformation was also accommodated by basal < a> slip and the dissociation of < c+a> dislocations. Center-of-symmetry (COS) analysis confirmed that the dissociation of < c+a> dislocations resulted in the formation of I₁ intrinsic stacking faults after cyclic loading. These findings provide new insights into the complex interplay of dislocation mechanisms governing fatigue deformation in rare-earth-containing Mg alloys.

Cyclic deformation↗
DOE OSTI2019

Magnetic Properties of the Dilute Magnetic Semiconductor Zn{sub 1-x}Co{sub x}O Nanoparticles

The magnetic properties of the dilute magnetic semiconductor (DMS) are due the existence of two competing interactions, a direct ferromagnetic interaction and an indirect antiferromagnetic interaction. This is well established in the Zn{sub 1-x}Mn{sub x}O DMS, but is controversy in the Zn{sub 1-x}Co{sub x}O DMS. To gain insights, a series of Co-substituted ZnO NRs (x = 0, 0.01, 0.02, 0.03, 0.04, and 0.05) have been fabricated using a low-temperature hydrothermal method. The magnetization of these Co-doped ZnO NPs was measured with a vibrating sample magneto-meter. Expressing the magnetization results in units of Bohr magnetons per Co ions, it is found that the ferromagnetic contributions become more dominant as more magnetic Co ions are doped into the ZnO NPs. X-ray diffraction, energy dispersive X-ray, scanning electron microscopy, and photoluminescence measurements were done to characterize the Co:ZnO NPs.

77 NANOSCIENCE AND NANOTECHNOLOGY↗